Aerospace Engineering Commons^™

Investigation Of Additively Manufactured Polymer And Transparent Polymer Composites, Gregory Taylor

Doctoral Dissertations

"The objective of this study is an investigation of both the characterization of fused deposition modeling (FDM) of polymer thermoplastics and the manufacture of glass-reinforced transparent composites. The flexural behavior and fracture toughness of FDM parts are critical for the evaluation and optimization of both material and process. This study focuses on the performance of FDM Ultem 1010 specimens intended to be used as composite tooling due the material's high heat resistance. A three-point bend test is performed for flexure properties while a single edge notch bend test is performed for fracture toughness. For each of the tests, the build …

Efficient Design Optimization Methodology For Nonconventional Laminated Thin-Walled Composite Structures, Mazen Albazzan

Theses and Dissertations

Structural designers seek the best possible design of a structure that optimally meets the requirements of a specific application. The measure of the quality of the final design can often be related to specific stiffness and strength of the structure. Because of their superior mechanical and environmental properties compared to traditional metals, fiberreinforced composite materials have earned a widespread acceptance for different structural applications. The tailoring potential of composites to achieve high specific stiffness and strength has promoted them as promising candidates for constructing lightweight structures. From that aspect, designers have tackled the problem of designing composite laminates, which is …

Crop Height Estimation With Unmanned Aerial Vehicles, Carrick Detweiler, David Anthony, Sebastian Elbaum

School of Computing: Faculty Publications

An unmanned aerial vehicle (UAV) can be configured for crop height estimation. In some examples, the UAV includes an aerial propulsion system, a laser scanner configured to face downwards while the UAV is in flight, and a control system. The laser scanner is configured to scan through a two-dimensional scan angle and is characterized by a maxi mum range. The control system causes the UAV to fly over an agricultural field and maintain, using the aerial propulsion system and the laser scanner, a distance between the UAV and a top of crops in the agricultural field to within a programmed …

Including Topographical Effects In Slant-Range Modeling, Kari C. Ward, Kyle J. Demarsy

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Spacecraft descent-to-landing navigation often includes the use of a slant-range measurement, the distance from the spacecraft to a surface along the off-nadir pointing direction of the sensor. Modeling a slant range sensor requires a reference surface, approximations of which include spherical and ellipsoidal surfaces, spherical harmonic models, and topographical maps based on prior reconnaissance data. For the spherical and ellipsoidal reference surfaces, a closed-form solution of the slant-range measurement exists. However, these approaches are inaccurate with respect to the true surface. This paper develops a method to implement digital elevation maps of a given surface to create a topography-based model …

Electric Solid Propellant Ablation In A Pulsed Electric Thruster, Matthew S. Glascock, Joshua L. Rovey

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Electric solid propellants are advanced solid chemical rocket propellant that can be controlled (ignited, throttled and extinguished) with electric current. Work reported here focuses on application of electric solid propellant in a pulsed electric thruster similar to a pulsed plasma thruster. In the future it may be possible to develop a dual-mode electric solid propellant thruster that is switchable between steady applied electric current chemical mode and pulsed alternating electric current electric mode. Results presented here use a laboratory test thruster to create an arc discharge of 5-20 J per pulse in a cylindrical cavity of propellant. Results for Teflon …

A Monolithic Internal Strain-Gage Balance Design Based On Design For Manufacturability, Thomas Ladson Webb Iii

Mechanical & Aerospace Engineering Theses & Dissertations

This paper proposes an alternative approach to internal strain-gage balance design driven by Design for Manufacturability (DFM) principles. The objective of this research was a reduction in fabrication time and, subsequently, cost of a balance by simplifying its design while maintaining basic stiffness and sensitivity. Traditionally, the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) balance designs have relied on Electro-Discharge Machining (EDM), which is a precise but slow and, therefore, expensive process. EDM is chosen due to several factors, including material hardness, surface finish, and complex geometry, including blind cuts. The new balance design objectives require no …

Evaluating Augmented Reality For Space Telerobotics Training, John Karasinski

Link Foundation Modeling, Simulation and Training Fellowship Reports

Despite the extensive previous research into manual tracking, to the author’s knowledge there exists no study in the literature addressing human performance or workload changes in manual tracking tasks between traditional computer monitors and mobile, augmented reality headsets. The aim of this study was to investigate the effect of several factors on human performance and workload in a three-axis manual tracking task. Recent advances in computing hardware have enabled a new generation of augmented reality stereoscopic devices, such as the Microsoft HoloLens, which have yet to be evaluated in the literature. The Microsoft HoloLens provides depth cues to the user …

Direct Numerical Simulation Of Pressure Fluctuations Induced By Supersonic Turbulent Boundary Layers, Chao Zhang

Doctoral Dissertations

"Direct Numerical Simulations are used to generate a database of high-speed zero-pressure-gradient turbulent boundary layers developing spatially over a flat plate with nominal freestream Mach number ranging from 2:5 to 14 and wall-to-recovery temperature ranging from 0:18 to 1:0. The flow conditions of the DNS are representative of the operational conditions of the Purdue Mach 6 quiet tunnel, the Sandia Hypersonic Wind Tunnel at Mach 8, and the AEDC Hypervelocity Tunnel No. 9 at Mach 14. The DNS database is used to gauge the performance of compressibility transformations, including the classical Morkovin's scaling and strong Reynolds analogy as well as …

The Separation Of Shear-Driven Liquid Films From A Sharp Corner, Zahra Sadeghizadeh

Doctoral Dissertations

"The separation of shear-driven liquid films occurs in many engineering applications such as port fuel injected engines, demisters, and gas transfer lines. Despite the importance of this problem, the details of the interaction between operating parameters such as liquid flow rate, gas velocities and liquid film properties on the forces at the expanding corner are still not clear. To enhance the insight on the complicated interaction between the gas and liquid phases, the shear-driven liquid flow around a corner has been studied both experimentally and analytically in this work. The effect of the complex liquid film structure on liquid mass …

Gust Alleviation System For General Aviation Aircraft, Lucas Coleman Mills

Mechanical & Aerospace Engineering Theses & Dissertations

A designed control motion scheme to improve passenger comfort in general aviation aircraft by reducing normal acceleration and pitch rate due to turbulence is investigated. An aerodynamic math model is created for ViGYAN’s Active Ride Improvement System flight article, a one-eighth scale Pilatus Porter PC-6 with conventional forward main wing, aft horizontal and vertical tails, and a single engine with tractor configuration. The test article incorporates a full-span gust flap and forward mounted gust sensor to mechanize the gust alleviation control system, and these features are present in the dynamic model. The model is a two degree of freedom linear …

Development Of A Cfd Model Of The Catalytic Combustion Of A Microtube Multi-Mode Propulsion System, Andrew Paul Taylor

Masters Theses

"This thesis presents the process and results of the development of a computational fluid dynamics (CFD) model in ANSYS Fluent 18.1 on the catalytic decomposition of a novel liquid monopropellant in a microtube in order to gain deeper insights than what is available through the experimental data. The CFD model was created using the Euler- Euler Multiphase model in conjunction with the Heterogeneous Reaction submodel. Such a choice of modeling setting was backed up by theory and benchmark computations on multiphase and compressible flow, shown in Section 3 and Appendix A. It was found that the previously determined one-step reaction …

The Design Of A Rocket Propulsion Labview Data Acquisition And Control System, Dylan Allan Ott

Open Access Theses & Dissertations

When designing a rocket engine, both the propulsion system and propellant choice(s) are an important deciding factor. Desired rocket engine behavior, specific impulse, and levels of thrust are all different between the various propulsion systems. A bi-propellant cryogenic liquid 5lbf, 500lbf, and 2000lbf rocket engine was designed and manufactured by UTEP. The 5lbf rocket engine is a Reaction Control Engine and the 500lbf and 2000lbf rocket engine is a throttleable Main Engine. To provide a reliable and safe data acquisition and control system for this experiment, a Real-Time control platform was needed. A compact DAQ system was purchased and configured …

Instrumentation And Inertial Navigation Systems Design For Tensegrity Robot Implementations, Scott Edward Harper

Graduate Theses, Dissertations, and Problem Reports (ETD)

One of the major challenges faced when developing missions for the exploration of planetary bodies is the risk these terrains pose on the science platform when using a traditional lander or wheeled rover. One means of developing platforms to traverse these harsh terrains is to utilize mobility systems comprised of tensegrity structures. These structures have the capacity to distribute loads across a network of axially loaded members such that they can be constructed in a very lightweight manner and morph their geometries when required. In literature, there has been significant progress in simulated environments to utilize tensegrity structures as mobility …

Robust Nonlinear Estimation And Control Applications Using Synthetic Jet Actuators, Natalie Ramos Pedroza

Doctoral Dissertations and Master's Theses

Limit cycle oscillations (LCO), also known as utter, cause significant challenges in flight control of small unmanned aerial vehicles (SUAVs), and could potentially lead to structural damage and catastrophic failures. LCO can be described as vibrational motions in the rocking, pitching and plunging displacements of an aircraft wing. To address this, the use of synthetic jet actuators (SJAs) in UAV flight control systems is becoming popular as a practical alternative and to mechanical deflection surfaces.

Synthetic jet actuators are promising tools for LCO suppression systems in small UAVs due to their small size, ease of operation, and low cost. Uncertainties …

The Effect Of Task Load, Automation Reliability, And Environment Complexity On Uav Supervisory Control Performance, Sarah M. Sherwood

Doctoral Dissertations and Master's Theses

Over the last decade, military unmanned aerial vehicles (UAVs) have experienced exponential growth and now comprise over 40% of military aircraft. However, since most military UAVs require multiple operators (usually an air vehicle operator, payload operator, and mission commander), the proliferation of UAVs has created a manpower burden within the U.S. military. Fortunately, simultaneous advances in UAV automation have enabled a switch from direct control to supervisory control; future UAV operators will no longer directly control a single UAV subsystem but, rather, will control multiple advanced, highly autonomous UAVs. However, research is needed to better understand operator performance in a …

Development Of A Supplier’S Delivery Time And Delivered Quality Performance Index And Assessment Of Alternative Decisions Regarding Underperforming Suppliers For The Aerospace Industry, Clint Saidy

Theses and Dissertations

This study investigates current practices of supplier’s delivery assessment so that a comprehensive index and a cost function model could be properly developed. Following a thorough literature review, a framework was created based on a penalty cost function that integrates both suppliers’ ability to deliver on time, as well as suppliers’ capability to deliver good quality. Afterward, suppliers could then be ranked and placed either in good standing, or transversely on probation. Underperforming suppliers face three potential outcomes based on current literature: (1) switching supplier, (2) increase collaboration, (3) maintaining the status quo. The decision vis-à-vis failing suppliers is based …

Relationship Between Airline Category, Geographical Region, And Safety Performance, Peter Simpson

Walden Dissertations and Doctoral Studies

Passengers rank safety as a key factor in airline choice. Thus, safety performance impacts an airline's ability to attract customers. The purpose of this correlational study was to examine the relationship and difference between airline category low-cost carriers (LCCs) and full-service carriers (FSCs), geographical region, and safety performance measured by accident rates. The target population comprised all airlines in all countries that had an accident during the 14-year period 2004 to 2017. Data consisted of archival data of all global airline accidents and airline departure frequencies for the 14-year period. The theory of organizational accidents in complex sociotechnical systems explains …

Study Of Biomimetic Micro And Macro Structures For Drag Reduction, Justin S. Schrout

Graduate Theses, Dissertations, and Problem Reports (ETD)

The ever increasing demand for global travel coupled with increasing costs of fuels have prompted many researchers to study new methods to save fuel to make travel more efficient. One of the proverbial low-hanging fruits for fuel efficiency is aerodynamic drag reduction. Simple changes in the shape or placement of structures on the surface of different types of vehicles have been shown to increase fuel efficiency by reducing drag (e.g., add-on lower and aft wake fairings on tractor trailers which have seen a tremendous rise in popularity on US highways in recent years). Areas of interest in drag reduction have …

Investigation Of 2195 And 2219 Post Weld Heat Treatments For Additive Friction Stir Lap Welds, Matthew Champagne

LSU New Orleans Theses and Dissertations

To evaluate potential uses for friction stir welding in additive manufacturing, two separate parts were fabricated, one of 2195-T84 and the other 2219-T87, utilizing fixed pin techniques and additive lap welds. The parts were cut into samples, artificially aged and subjected to Rockwell hardness (HRB), Vickers hardness, micrographic photography, and metallographic imaging on both pre- and post- heat treatment. Additionally, tensile testing was performed on the heat-treated samples. A comparisons of test results showed a minimal increase in the yield strength of the 2195-T84 samples compared to as-welded tensile results obtained from a previous project. The ultimate tensile strength was …

Design, Manufacture, And Structural Dynamic Analysis Of A Biomimetic Insect-Sized Wing For Micro Air Vehicles, Jose Enrique Rubio

LSU New Orleans Theses and Dissertations

The exceptional flying characteristics of airborne insects motivates the design of biomimetic wing structures that can exhibit a similar structural dynamic behavior. For this purpose, this investigation describes a method for both manufacturing a biomimetic insect-sized wing using the photolithography technique and analyzing its structural dynamic response. The geometry of a crane fly forewing (family Tipulidae) is acquired using a micro-computed tomography scanner. A computer-aided design model is generated from the measurements of the reconstructed scanned model of the insect wing to design the photomasks of the membrane and the venation network required for the photolithography procedure. A composite …

Synthetic Jet Actuator-Based Aircraft Tracking Using A Continuous Robust Nonlinear Control Strategy, N. Ramos-Pedroza, W. Mackunis, M. Reyhanoglu

Publications

A robust nonlinear control law that achieves trajectory tracking control for unmanned aerial vehicles (UAVs) equipped with synthetic jet actuators (SJAs) is presented in this paper. A key challenge in the control design is that the dynamic characteristics of SJAs are nonlinear and contain parametric uncertainty. The challenge resulting from the uncertain SJA actuator parameters is mitigated via innovative algebraic manipulation in the tracking error system derivation along with a robust nonlinear control law employing constant SJA parameter estimates. A key contribution of the paper is a rigorous analysis of the range of SJA actuator parameter uncertainty within which asymptotic …

Outer Space: A Steam Voyage, Jancy Mcphee

The Transdisciplinary STEAM+ Journal

SciArt Exchange offers multi-disciplinary art contests, artwork events, consulting, training and community resources to support science and technology education, collaboration, and innovation. Using a science-integrated- with-art approach, SciArt Exchange supports, prepares, and convenes people of all ages, backgrounds and affiliations to discuss and potentially solve space, science, and technology challenges. This field note shares the Humans in Space Art Program and the Project Mars Competition.

The Effect Of Z-Binding Yarns On The Electrical Properties Of 3d Woven Composites, Mohamed Nasr Saleh, Arief Yudhanto, Gilles Lubineau, Constantinos Soutis

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Electrical resistance monitoring (ERM) has been used to study the effect of the z-binding yarns on the initial electrical resistance (ER) and its change of three architectures of 3D woven carbon fiber composites namely (orthogonal "ORT", layer-to-layer "LTL" and angle interlock "AI") when tested in tension. Specimens are loaded in on-axis "warp" and off-axis "45°" directions. In situ ERM is achieved using the four-probe technique. Monotonic and cyclic "load/unload" tests are performed to investigate the effect of piezo-resistivity and residual plasticity on resistance variation. The resistance increases for the off-axis loaded specimens (∼90%) is found to be higher than that …

A Comparison Of The Aerodynamic Centers For Panel Code Compressible Corrections And Openfoam 5 For Mach 0.1 To 0.8, Dustin Weaver

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

It is known that the aerodynamic center changes from quarter chord to half chord from incompressible to compressible flows on airfoils. Compressible corrections are derived and implemented in a vortex panel code. These results will be used to find the aerodynamic centers for the specified Mach range of 0.1 to 0.8 in 0.1 increments within - 6 to 6 degrees angle of attack. OpenFOAM 5 cases will be created with specific meshes and settings. The results calculated from OpenFOAM 5 will be compared to the results obtained from the compressible corrections.

Multiphase Flow Modeling For Design And Optimization Of A Novel Down-Flow Bubble Column, Mutharasu Lalitha Chockalingam

LSU Doctoral Dissertations

The application of the Euler-Euler framework based Computational Fluid Dynamics (CFD) models for simulating the two-phase gas-liquid bubbly flow in down-flow bubble columns is discussed in detail. Emphasis is given towards the modelling and design optimization of a novel down-flow bubble column. The design features of this novel down-flow bubble column and its advantages over a conventional Plunging Jet down-flow bubble column are discussed briefly. Then, some of the present challenges in simulating a conventional Plunging Jet down-flow bubble column in the Euler-Euler framework is highlighted, and a sigmoid function based drag modification function is implemented to overcome those challenges. …

Flight Dynamics: Flying Qualities Of Handling Factors Are Engineered Into The Aircraft Design, Nihad E. Daidzic

Aviation Department Publications

Flight dynamics is an aerospace engineering discupline that addresses aircraft stability and controllability. It is also mathematically very intensive and is traditionally the most difficult in the pilot training curriculum. Ultimately, it does not matter how good steady-state performance of an aircraft design is if its flying (handling) qualities are deficient. Paradoxically, the first airplane Wright Flyer, was statically and dynamically unstable, had large control authority, and was difficult to fly. We've come a long way since those early days, but stability is still vitally important in aircraft design and flight ops. The focus of this article will be airplane …

Rotordynamic Enhancement By Utilizing The Controlled Hydrostatic Injection Of Hybrid Air Foil Bearing, Behzad Zamanian Yazdi

Mechanical and Aerospace Engineering Dissertations - Archive

Air foil bearings (AFBs) are introduced as promising bearings for oil-free turbomachinery applications. Air foil bearing (AFB) technology has made substantial advancement during the past decades and found its applications in various small turbomachinery. AFBs provide reliable operation at high speed and high temperature with negligible power loss. However, rotordynamic instability, friction and drag during the start/stop, and thermal management are still challenges for further application of the technology. Hybrid Air Foil Bearing (HAFB) technology utilizes the radial injection of externally pressurized air into the traditional hydrodynamic AFB’s film thickness through orifices attached to the top foil. HAFB is one …

Optimization Of Aircraft Tow Steered Composite Wing Structures, Micheal Chamberlain Henson

Mechanical and Aerospace Engineering Dissertations - Archive

An efficient methodology for design of aircraft composite wing structures is presented. The developed approach provides a flexible and integrated strategy to leverage advantages of composite material tow steering to achieve more effective wing designs. This is accomplished by including the coupling between OML geometry, aerodynamics and structural response. Structural and aerodynamic analyses are derived from parametric aircraft geometry and assembled into a framework for aero-structural wing sizing. A Ritz equivalent plate solution is extended to model composite materials with variable fiber path geometry. The structural modeling approach is implemented to automate creation of both Ritz and finite element analyses. …

A Micromechnics Approach To Predicting The Onset Yielding Envelope Of Particulate Composite Materials, Behrooz Karimi

Mechanical and Aerospace Engineering Dissertations - Archive

Composite materials fail for various reasons and extensive research has been conducted both experimentally and theoretically. However, theoretical prediction of composite failure by yielding seems scarce. Adding reinforcing elements to matrix significantly affects the structural behavior of composite materials. The inserted particles on one hand obstruct the progress of cracks and on the other hand cause stress concentration on the interface of the particle-matrix and eventually influence the ultimate strength of the material. In this research, we study the interface stresses and strength in particulate reinforced composites under uniform mechanical and thermal loading. We theoretically obtain failure envelopes for particulate …

Towards The Fabrication Of Bioresorbable Constructs With Customized Properties Using Additive Manufacturing, Prashanth Ravi

Mechanical and Aerospace Engineering Dissertations - Archive

Additive Manufacturing (AM) has been employed to fabricate medical constructs for over two decades. This dissertation investigates the effects of AM process parameters on raster level geometric features and structural properties of bioresorbable constructs. The development of an open architecture custom multi-process 3D printer employed for fabricating bioscaffolds and test structures is discussed. Bioresorbable polymers including a newly synthesized radiopaque polymer, poly (glycerol sebacate fumarate) gadodiamide (Rylar) and medical grade poly-L-lactic acid (PLLA) were investigated. In the first part, the effects of process parameters on raster geometry were investigated to aid in the fabrication of structures with improved geometric features …