Aerospace Engineering Commons^™

Filament Winding Composite Airframes For Sounding Rockets, Eric Ford

Student Works

This study’s objective was to determine the feasibility of manufacturing carbon fiber cylinders using an X-Winder filament winder for a structural airframe in sounding rockets. Multiple carbon fiber tubes were manufactured using the X-Winder and tested. The results of this testing successfully demonstrated that tubes manufactured with the X-Winder are capable of performing as an airframe for small sounding rockets. Five tube samples were destructively tested in compression, and the average maximum compressive strength of the tubes was 9,854 lbf. One of the tubes was used as the airframe in a small sounding rocket which flew to 4,042 feet above …

Narmax Identification Based Closed-Loop Control Of Flow Separation Over Naca 0015 Airfoil, Sohaib Obeid, Goodarz Ahmadi, Ratneshwar Jha

Henry M. Rowan College of Engineering Departmental Research

A closed-loop control algorithm for the reduction of turbulent flow separation over NACA 0015 airfoil equipped with leading-edge synthetic jet actuators (SJAs) is presented. A system identification approach based on Nonlinear Auto-Regressive Moving Average with eXogenous inputs (NARMAX) technique was used to predict nonlinear dynamics of the fluid flow and for the design of the controller system. Numerical simulations based on URANS equations are performed at Reynolds number of 106 for various airfoil incidences with and without closed-loop control. The NARMAX model for flow over an airfoil is based on the static pressure data, and the synthetic jet actuator is …

Numerical Method For Rapid Aerostructural Design And Optimization, Jeffrey D. Taylor, Douglas F. Hunsaker

Mechanical and Aerospace Engineering Student Publications and Presentations

During early phases of wing design, analytic and low-fidelity methods are often used to identify promising design concepts. In many cases, solutions obtained using these methods provide intuition about the design space that is not easily obtained using higher-fidelity methods. This is especially true for aerostructural design. However, many analytic and low-fidelity aerostructural solutions are limited in application to wings with specific planforms and weight distributions. Here, a numerical method for minimizing induced drag with structural constraints is presented that uses approximations that apply to wings with arbitrary planforms and weight distributions. The method is applied to the NASA Ikhana …

Aerodynamic And Aeroacoustic Performance Of Small Uav Propellers In Static Conditions, William Jordan, Robert W. Deters, Shreyas Narsipur

Publications

The proliferation of small multi-rotor UAVs in commercial, recreational, and surveillance spheres has garnered significant interest in the noise produced by these vehicles. The current research aims to study the relationship between the aerodynamic performance and acoustic characteristics of small-scale UAV propellers. Three commercially available propellers for the DJI Phantom 2/3 UAV were selected for preliminary development and validation of an aeroacoustic experimental test setup and associated data reduction methods. Propeller thrust, torque, and power measurements were recorded at static conditions. Upon successful validation of the test bench, acoustic measurements were taken at the propeller disk’s upstream and in-plane locations. …

Performance Testing Of Aero-Naut Camfolding Propellers, Or D. Dantsker, Robert W. Deters, Marco Caccamo, Michael S. Selig

Publications

The increase in popularity of unmanned aerial vehicles (UAVs) has been driven by their use in civilian, education, government, and military applications. However, limited on-board energy storage significantly limits flight time and ultimately usability. The propulsion system plays a critical part in the overall energy consumption of the UAV; therefore, it is necessary to determine the most optimal combination of possible propulsion system components for a given mission profile, i.e. propellers, motors, and electronic speed controllers (ESC). Hundreds of options are available for the different components with little performance specifications available for most of them. By examining a variety of …

Vibration Isolation System, Bradley Y. Kwan, Bailey Groh, Max Wu, Nicole Yen

Mechanical Engineering

The Vibration Isolation System Senior Project is a collaborative group project between its sponsor, Maxar Technologies, and a team of students from Cal Poly - SLO to effectively design, manufacture, and test a structural assembly for satellites, isolating vibrations during launch and orbit conditions. After initial sponsor contact, requirements and needs were set which dictated deliverables for the senior project group. The group performed analyses to validate all design decisions, including a modified concept and design direction, selection of a prototype viscoelastic damping material, preliminary testing to validate design specifications, and detailed design and analysis toward a finalized design. Instead …

Design Of A Martian Communication Constellation Of Cubesats, Scott J. Pirkle

Master's Theses

Spacecraft operating on the Martian surface have used relay satellites as a means of improving communication capabilities, mainly in terms of bandwidth and availability. However, the spacecraft used to achieve this have been large spacecraft (1000s of kilograms) and were not designed with relay capability as the design priority. This thesis explores the possibility of using a CubeSat-based constellation as a communications network for spacecraft operating on the Martian surface. Brute-force techniques are employed to explore the design space of possible constellations. An analysis of constellation configurations that provide complete, continuous coverage of the Martian surface is presented. The stability …

Design, Validation, And Verification Of The Cal Poly Educational Cubesat Kit Structure, Nicholas B. Snyder

Master's Theses

In this thesis, the development of a structure for use in an educational CubeSat kit is explored. The potential uses of this kit include augmenting existing curricula with aspects of hands on learning, developing new ways of training students on proper space systems engineering practices, and overall contributing to academic capacity building at Cal Poly and its collaborators. The design improves on existing CubeSat kit structures by increasing accessibility to internal components by implementing a modular backplane system, as well as adding the ability to be environmentally tested. Manufacturing of the structure is completed with both additive (Fused Deposition Modeling …

A Parametric Study Of Formation Flight Of A Wing Based On Prandtl's Bell-Shaped Lift Distribution, Kyle S. Lukacovic

Master's Theses

The bell-shaped lift distribution (BSLD) wing design methodology advanced by Ludwig Prandtl in 1932 was proposed as providing the minimum induced drag. This study used this method as the basis to analyze its characteristics in two wing formation flight. Of specific interest are the potential efficiency savings and the optimal positioning for formation flight. Additional comparison is made between BSLD wings and bird flight in formation.

This study utilized Computational Flow Dynamics (CFD) simulations on a geometric modeling of a BSLD wing, the Prandtl-D glider. The results were validated by modified equations published by Prandtl, by CFD modeling published by …

Initial Orbit Determination Error Analysis Of Low-Earth Orbit Rocket Body Debris And Feasibility Study For Debris Cataloguing From One Optical Facility, Kyle Stoker

Master's Theses

This paper is predicated on determining the effectiveness of angles-only initial orbit determination (IOD) methods when limited observational data is available for low-Earth orbit (LEO) rocket body debris. The analysis will be conducted with data obtained from Lockheed Martin Space’s Space Object Tracking (SpOT) facility, focusing on their observational data from 2018 that contains tracking of rocket body debris for less than one minute per overhead pass. After the IOD accuracies are better understood, a feasibility study will follow that investigates the possibility of cataloguing LEO orbital debris from a single optical observation facility with similar observational capabilities as that …

A Study Of The Design Of Adaptive Camber Winglets, Justin J. Rosescu

Master's Theses

A numerical study was conducted to determine the effect of changing the camber of a winglet on the efficiency of a wing in two distinct flight conditions. Camber was altered via a simple plain flap deflection in the winglet, which produced a constant camber change over the winglet span. Hinge points were located at 20%, 50% and 80% of the chord and the trailing edge was deflected between -5° and +5°. Analysis was performed using a combination of three-dimensional vortex lattice method and two-dimensional panel method to obtain aerodynamic forces for the entire wing, based on different winglet camber configurations. …

Pocket Rocket: A 1u+ Propulsion System Design To Enhance Cubesat Capabilities, James M. Harper

Master's Theses

The research presented provides an overview of a 1U+ form factor propulsion system design developed for the Cal Poly CubeSat Laboratory (CPCL). This design utilizes a Radiofrequency Electrothermal Thruster (RFET) called Pocket Rocket that can generate 9.30 m/s of delta-V with argon, and 20.2 ± 3 m/s of delta-V with xenon. Due to the demand for advanced mission capabilities in the CubeSat form factor, a need for micro-propulsion systems that can generate between 1 – 1500 m/s of delta-V are necessary.

By 2019, Pocket Rocket had been developed to a Technology Readiness Level (TRL) of 5 and ground tested in …

Impulse And Performance Measurements Of Electric Solid Propellant In A Laboratory Electrothermal Ablation-Fed Pulsed Plasma Thruster, Matthew S. Glascock, Joshua L. Rovey, Kurt A. Polzin

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Electric solid propellants are advanced solid chemical rocket propellants that can be controlled (ignited, throttled and extinguished) through the application and removal of an electric current. This behavior may enable the propellant to be used in multimode propulsion systems utilizing the ablative pulsed plasma thruster. The performance of an electric solid propellant operating in an electrothermal ablation-fed pulsed plasma thruster was investigated using an inverted pendulum micro-newton thrust stand. The impulse bit and specific impulse of the device using the electric solid propellant were measured for short-duration test runs of 100 pulses and longer-duration runs to end-of-life, at energy levels …

Conceptual Design Of A South Pole Carrier Pigeon Uav, Kendrick M. Dlima

Master's Theses

Currently, the South Pole has a large data problem. It is estimated that 1.2 TB of data is being produced every day, but less than 500 GB of that data is being uploaded via aging satellites to researchers in other parts of the world. This requires those at the South Pole to analyze the data and carefully select the parts to send, possibly missing out on vital scientific information. The South Pole Carrier Pigeon will look to bridge this data gap.

The Carrier Pigeon will be a small unmanned aerial vehicle that will carry a 30 TB solid-state hard drive …

Thermal Modeling And Testing Of The Blue Thermal Vacuum Chamber, Madeline R. Jensma

Master's Theses

The Blue Thermal Vacuum Chamber (TVAC) located in the Space Environments Laboratory at California Polytechnic State University, San Luis Obispo (Cal Poly), may be used for thermal vacuum testing of test articles that fit with in the semi cylindrical test section that has a radius of approximately 18 cm and a length of 61 cm. The potential test articles include CubeSat systems and subsystem. The Blue TVAC can also be used for educational and research purposes. The goal of this thesis project is to develop a thermal model of the Blue TVAC to predict and analyze the thermal response of …

A Study Of The Standard Cirrus Wing Lift Distribution Versus Bell Shaped Lift Distribution, William H. Bergman

Master's Theses

This thesis discusses a comparison of the differences in aerodynamic performance of wings designed with elliptical and bell-shaped lift distributions. The method uses a Standard Cirrus sailplane wing with a lift distribution associated with the induced drag benefits of an elliptical distribution (span efficiency = 0.96) as the basis of comparison. The Standard Cirrus is a standard class sailplane with 15-meter wingspan that was designed by Schempp-Hirth in 1969. This sailplane wing was modeled and analyzed in XFLR5, then validated against existing wind tunnel airfoil data, and Standard Cirrus flight test data. The root bending moment of the baseline wing …

A Study Of The Utilization Of Panel Method For Low Aspect Ratio Wing Analysis, William Barton D. Newey

Master's Theses

This study demonstrates the applicability of using a modified application strategy of panel method to analyze low aspect ratio wings at preliminary design phases. Conventional panel methods fail to capture the leading edge vortex (LEV) that is shed by wings with low aspect ratios, typically below 2 depending on planform. This aerodynamic phenomenon contributes to a significant amount of the lift of these wings and the result is a drastic underestimation of the lift characteristics when analyzed by conventional panel method. To capture the effect of the leading edge vortex, a panel method code was used with an extended definition …

Three Axis Attitude Control System Design And Analysis Tool Development For The Cal Poly Cubesat Laboratory, Liam T. Bruno

Master's Theses

The Cal Poly CubeSat Laboratory (CPCL) is currently facing unprecedented engineering challenges—both technically and programmatically—due to the increasing cost and complexity of CubeSat flight missions. In responding to recent RFPs, the CPCL has been forced to find commercially available solutions to entire mission critical spacecraft subsystems such as propulsion and attitude determination & control, because currently no in-house options exist for consideration. The commercially available solutions for these subsystems are often extremely expensive and sometimes provide excessively good performance with respect to mission requirements. Furthermore, use of entire commercial subsystems detracts from the hands-on learning objectives of the CPCL by …

Application Of Mounting Personal Pid Voc Sensors To Small Unmanned Aircraft Systems To Aid First Responders, Cheri Marcham

Publications

Small Unmanned Aerial Systems in Emergency Response

• Current sUAS Uses
• Search and rescue
• Thermal imaging
• Evaluating structural stability
• Spread of wildfires
• Storm damage

Design And Test Of An Autonomy Monitoring Service To Detect Divergent Behaviors On Unmanned Aerial Systems, Loay Y. Almannaei

Theses and Dissertations

Operation of Unmanned Aerial Vehicles (UAV) support many critical missions in the United State Air Force (USAF). Monitoring abnormal behavior is one of many responsibilities of the operator during a mission. Some behaviors are hard to be detect by an operator, especially when flying one or more autonomous vehicles; as such, detections require a high level of attention and focus to flight parameters. In this research, a monitoring system and its algorithm are designed and tested for a target fixed-wing UAV. The Autonomy Monitoring Service (AMS) compares the real vehicle or simulated Vehicle with a similar simulated vehicle using Software …

Safran Seat Attachment System, Craig John Kimball, Tyler Bragg, Lynette Cox

Mechanical Engineering

This final design review (FDR) document outlines the senior design project being carried out by a team of mechanical engineering undergraduate students attending California Polytechnic State University, San Luis Obispo for Safran Seats in Santa Maria, CA. The project originally was to design, build, and test a universal attachment to secure a widebody business class seat to seven aircraft models with different seat track geometry. The goal was to design, document, and create a finished product that fits design, weight, and manufacturing requirements, as well as passes static 9G FWD testing. Structural analysis, manufacturing analysis, FEA, and CAD assemblies will …

Miniaturized Ultraviolet Imager Phase Iii, Bradley D. Albright, Nicolas A. Armenta, Colin W. Harrop

Mechanical Engineering

This document details the work to date, June 9, 2020, done by the Cal Poly Mechanical Engineering senior project team, Miniaturized Ultraviolet Imager: Phase III (MUVI III), sponsored by the University of California, Berkeley – Space Sciences Laboratory (UCB SSL). MUVI III is the third senior project team of an ongoing design, MUVI: the prototype of a 2U sized CubeSat intended to capture aurora images in the ionosphere. The first team, MUVI I, finished development of the UV imager. The second team, MUVI II, designed the mirror mounting and deployable door mechanisms. The goal of MUVI phase III is to …

Development Of A State-Space Aeroelastic Model Of A Flexible T-Tail Aircraft For Flutter Analysis, Patrick S. Downs

Doctoral Dissertations and Master's Theses

Flutter prediction is an important part of the preliminary design process of any new aircraft. Current analysis methods include coupled fluid structure interaction codes and doublet lattice panel codes. The computation resources and time required for CFD solutions makes them unattractive for preliminary design and doublet lattice models require considerable pre and post processing to provide satisfactory results. Thus, a process for developing an analytical model to facilitate rapid design changes and the implementation of active control systems is the main motivation of this thesis. An analytical model is developed by first deriving the equations of motion of the structure …

Work-In-Progress: Augmented Reality System For Vehicle Health Diagnostics And Maintenance, Yuzhong Shen, Anthony W. Dean, Rafael Landaeta

Electrical & Computer Engineering Faculty Publications

This paper discusses undergraduate research to develop an augmented reality (AR) system for diagnostics and maintenance of the Joint Light Tactical Vehicle (JLTV) employed by U.S. Army and U.S. Marine Corps. The JLTV’s diagnostic information will be accessed by attaching a Bluetooth adaptor (Ford Reference Vehicle Interface) to JLTV’s On-board diagnostics (OBD) system. The proposed AR system will be developed for mobile devices (Android and iOS tablets and phones) and it communicates with the JLTV’s OBD via Bluetooth. The AR application will contain a simplistic user interface that reads diagnostic data from the JLTV, shows vehicle sensors, and allows users …

3-D Printed Hybrid Propulsion Solutions For Smallsat Lunar Landing And Sample Return, Stephen A. Whitmore

Funded Research Records

No abstract provided.

Development And Application Of Elliptic Blending Lag K-Omega Sst Standard And Wall-Distance-Free Turbulence Model, Wenjie Shang

McKelvey School of Engineering Graduate Student Theses & Dissertations

In recent decades, Computational Fluid Dynamics (CFD) has become the most widely used technology to understand the fundamental complex fluid dynamics of turbulent flows as well as for modeling of turbulent flows in industrial applications. In industrial applications, the widely used methodology is to solve Reynolds-Average Navier-Stokes Equations (RANS) equations in conjunction with a turbulence model since it strikes a balance between accuracy and computational cost compared to other high fidelity approaches namely the Large Eddy Simulation (LES) and Direct Numerical Simulation (DNS), There are a large number of turbulence models proposed in past five decades, majority of them are …

Thermal Transport Across The Interface Between Liquid N-Dodecane And Its Own Vapor: A Molecular Dynamics Study, Eric Bird, Jesus Gutierrez Plascencia, Zhi Liang

Mechanical and Aerospace Engineering Faculty Research & Creative Works

There Are Two Possible Thermal Transport Mechanisms at Liquid-Gas Interfaces, Namely, Evaporation/condensation (I.e., Heat Transfer by Liquid-Vapor Phase Change at Liquid Surfaces) and Heat Conduction (I.e., Heat Exchange by Collisions between Gas Molecules and Liquid Surfaces). using Molecular Dynamics (MD) Simulations, We Study Thermal Transport Across the Liquid-Vapor Interface of a Model N-Dodecane (C12H26) under Various Driving Force Conditions. in Each MD Simulation, We Restrict the Thermal Energy to Be Transferred Across the Liquid-Vapor Interface by Only One Mechanism. in Spite of the Complex Intramolecular Interactions in N-Dodecane Molecules, Our Modeling Results Indicate that the Schrage Relationships, Which Were Shown …

Congressional Committee Resources On Space Policy During The 115th Congress (2017-2018): Providing Context And Insight Into Us Government Space Policy, Bert Chapman

Libraries Faculty and Staff Presentations

Article 1 of the US Constitution assigns the US Congress numerous responsibilities. These include creating new laws, revising existing laws, funding government programs, and conducting oversight of these programs' performance. Oversight of US Government agency space policy programs is executed by various congressional space policy committees including the House and Senate Science Committees, Armed Services, and Appropriations Committees. These committees conduct many public hearings on space policy, which invite expert witnesses to testify on US space policy programs and feature debate on the strengths and weaknesses of these programs. Documentation produced by these committees is widely available to the public, …

Wind Tunnel Wake Generator, Carl Pickl, James L. Rutledge, Marc D. Polanka, Brian Crabtree, Christopher Harkless

AFIT Patents

A wake generator for placement in a wind tunnel between a wind source and a test object includes a first frame member having a first track formed thereon, where the first track has a shape including a first side that is substantially rounded and a second side that is substantially flat. The wake generator may include a mounting plate disposed within a perimeter of the first track, where the mounting plate is rotatable relative to the first frame member about a first axis. The wake generator may also include a plurality of bars slidably engaged to the mounting plate and …

Delaying Flow Separation Using Piezoelectric Actuators, Kenechukwu Okoye

Honors Theses

Flow separation causes aircraft to experience an increase in drag degrading their aviation performance. The goal of the study was to delay flow separation on an airfoil by embedding a high-frequency translational piezoelectric actuator along the surface of the airfoil. This study investigated the extent to which the high-frequency translational piezoelectric actuator displaces the flow separation downstream or prevents it altogether utilizing a fog-based flow visualization experiment. The actuators with two actuation surfaces were embedded on the suction surface of an Eppler 862 airfoil model and placed in a low-speed wind tunnel. Dry ice fog streams were injected into the …