Aerospace Engineering Commons^™

Atmospheric Pressure Calibration To Improve Accuracy Of Transponder-Based Aircraft Operations Counting Technology, John H. Mott, Chuyang Yang, Darcy M. Bullock

Journal of Aviation Technology and Engineering

In the United States, over 2,400 of the 2,941 non-primary National Plan of Integrated Airport System airports have limited means of establishing operations counts due to lack of available personnel. Precise counts of airport operations are helpful for allocating airport improvement funds, as well as for local and system planning. An emerging technology utilizing ADS-B position data to calibrate signal strength received from Mode C transponders, thereby capturing location information from over 90% of the aircraft operating in the National Airspace System, has successfully estimated operations counts at these non-towered airports with reasonable levels of accuracy. This paper evaluates the …

Tooling Design Modeling For Composite Fuselage Of Beechcraft King Air 250 Using Catia, Miazor Fidelis Ekom

Journal of Aviation Technology and Engineering

Aircraft’s constant operation in tough conditions necessitates the need for structural components of high strength yet low weight. Composite materials are being used as an alternative to conventional aluminum alloys because of their competitive strength-to-weight and stiffness-to-weight ratios. In this paper, the detailed design procedure of a light-aircraft composite material fuselage tooling in three dimensions is shown. In its operation, the layup tools provide a surface for the composite part which is the correct shape of the part and is stable through the cure cycle, and also providing a means of indexing the part for the next manufacturing operation. This …

Viability And Application Of Mounting Personal Pid Voc Sensors To Small Unmanned Aircraft Systems, Cheryl Lynn Marcham, Scott Burgess, Joseph Cerreta, Patti J. Clark, James P. Solti, Brandon Breault, Joshua G. Marcham

Publications

Using a UAS-mounted sensor to allow for a rapid response to areas that may be difficult to reach or potentially dangerous to human health can increase the situational awareness of first responders of an aircraft crash site through the remote detection, identification, and quantification of airborne hazardous materials. The primary purpose of this research was to evaluate the remote sensing viability and application of integrating existing commercial-off-the-shelf (COTS) sensors with small unmanned aircraft system (UAS) technology to detect potentially hazardous airborne contaminants in emergency leak or spill response situations. By mounting the personal photoionization detector (PID) with volatile organic compound …

Numerical Reconstruction Of Spalled Particle Trajectories In An Arc-Jet Environment, Raghava S. C. Davuluri, Sean C. C. Bailey, Kaveh A. Tagavi, Alexandre Martin

Mechanical Engineering Faculty Publications

To evaluate the effects of spallation on ablative material, it is necessary to evaluate the mass loss. To do so, a Lagrangian particle trajectory code is used to reconstruct trajectories that match the experimental data for all kinematic parameters. The results from spallation experiments conducted at the NASA HYMETS facility over a wedge sample were used. A data-driven adaptive methodology was used to adapts the ejection parameters until the numerical trajectory matches the experimental data. The preliminary reconstruction results show that the size of the particles seemed to be correlated with the location of the ejection event. The size of …

Comparison Of Theoretical And High-Fidelity Aerostructural Solutions, Jeffrey D. Taylor, Douglas F. Hunsaker

Mechanical and Aerospace Engineering Student Publications and Presentations

As contemporary aerostructural research in aircraft design trends toward high-fidelity computational methods, aerostructural solutions based on theory are often neglected or forgotten. In fact, in many modern aerostructural wing optimization studies, the elliptic lift distribution is used as a benchmark in place of theoretical aerostructural solutions with more appropriate constraints. In this paper, we review several theoretical aerostructural solutions that could be used as benchmark cases for wing design studies, and we compare them to high-fidelity solutions with similar constraints. Solutions are presented for studies with 1) constraints related to the wing integrated bending moment, 2) constraints related to the …

Characterization Of The Common Research Model Wing For Low-Fidelity Aerostructural Analysis, Jeffrey D. Taylor, Douglas F. Hunsaker

Mechanical and Aerospace Engineering Student Publications and Presentations

A characterization of the Common Research Model (CRM) wing for low-fidelity aerostructural optimization is presented. The geometric and structural properties are based on the CAD geometries and finite-element models for the CRM wing and the undeflected Common Research Model Wing (uCRM). Three approximations are presented for the elastic axis from previously-published studies on wing boxes similar to the uCRM, and approximations of the flexural and torsional rigidity are presented from a previously-published study using the uCRM wing. The characterization presented in this paper is intended to be used within low-fidelity aerostructural analysis tools to facilitate rapid design optimization and exploratory …

Sensitivity And Estimation Of Flying-Wing Aerodynamic, Propulsion, And Inertial Parameters Using Simulation, Jaden Thurgood, Douglas F. Hunsaker

Mechanical and Aerospace Engineering Student Publications and Presentations

This paper explores the difficulties of aircraft system identification, specifically parameter estimation, for a rudderless aircraft. A white box method is used in conjunction with a nonlinear six degree-of-freedom aerodynamic model for the equations of motion in order to estimate 33 parameters that govern the aerodynamic, inertial, and propulsion forces within the mathematical model. The analysis is conducted in the time-domain of system identification. Additionally, all the parameters are estimated using a single flight rather than a series of shorter flights dedicated to estimating specific sets of parameters as is typically done. A final flight plan is developed with a …

Performance Of A Dual Plane Airfoil Model With Varying Gap, Stagger, And Decalage Using Pressure Measurements And Particle Image Velocimetry, Salome Kenneth Nunes

Browse all Theses and Dissertations

The dual-plane airfoil has been adopted in the design of aircraft wings, wind turbine blades, and propellers. The purpose of this research is to investigate the most important design parameters of a dual-plane airfoil model for the best aerodynamic performance, such as gap, stagger, and decalage. The dual-plane airfoil model was designed using the S826 profile. A mechanical mechanism with electrical actuator control is particularly designed to alter the gap and stagger smoothly, as well as the angle of attack (AOA) for each airfoil. It results in a gap range of 1.38c to 2.17c, a stagger range of -0.75c to …

Hybrid Models As Transdisciplinary Research Enablers, Andreas Tolk, Alison Harper, Navonil Mustafee

Computational Modeling & Simulation Engineering Faculty Publications

Modelling and simulation (M&S) techniques are frequently used in Operations Research (OR) to aid decision-making. With growing complexity of systems to be modelled, an increasing number of studies now apply multiple M&S techniques or hybrid simulation (HS) to represent the underlying system of interest. A parallel but related theme of research is extending the HS approach to include the development of hybrid models (HM). HM extends the M&S discipline by combining theories, methods and tools from across disciplines and applying multidisciplinary, interdisciplinary and transdisciplinary solutions to practice. In the broader OR literature, there are numerous examples of cross-disciplinary approaches in …

A Multi-Agent Semi-Cooperative Unmanned Air Traffic Management Model With Separation Assurance, Yanchao Liu

Industrial and Systems Engineering Faculty Research Publications

This paper presents an air traffic management framework to enable multiple fleets of unmanned aerial vehicles to traverse dense, omni-directional air traffic safely and efficiently. The main challenge addressed here is separation assurance in the absence of full coordination and communication. In this framework, each fleet is independently managed by a routing agent, which progressively plans the non-overlapping move-ahead corridors for vehicles in the fleet by solving a nonlinear optimization model. The model is artfully designed so that agents of different fleets need not engage in complicated multilateral communications or make guesses about external vehicles’ flight intents to maintain effective …

Spacecraft Informatics, K. L. Yung, Lida Xu, Chris Zhang

Information Technology & Decision Sciences Faculty Publications

No abstract provided.

Molten Regolith Electrolysis Processing For Lunar Isru: Financial And Physics Analysis Of Spacex Starship Transportation, Cheyenne Harper

Honors Undergraduate Theses

The purpose of the following research is to explore molten regolith electrolysis (MRE) methodology for in-situ resource utilization (ISRU) of Highlands lunar regolith, to be explored during the initial Artemis missions. An analysis of potential commercial launch providers for MRE-equipment based on technology-readiness level (TRL), payload mass support, and $ USD/kg payload price is provided. SpaceX is ultimately proposed as a launch provider of MRE equipment following multi-factorial analysis, with the SpaceX Starship human landing system (HLS) variant proposed for supporting MRE payload. Finally, customers of regolith-derived oxygen, aluminum, and silicon are distinguished to form the business case for operating …

A Finite Difference Model For Induced Hypothermia During Shock, Dylan S. Lyon

Honors Undergraduate Theses

The modified Fiala model from Westin was implemented with conditions for circulatory shock and hypothermia. The purpose is to model Emergency Preservation and Resuscitation (EPR), a procedure for inducing hypothermia in patients. Cold tissue temperatures reduce metabolism exponentially, greatly extending the window of anaerobic metabolic activity before permanent deoxygenation damage. EPR in patients undergoing hypovolemic shock can preserve the patient until primary surgical care and blood transfusions are attainable., thereby increasing survival rates. The main applications of EPR are military in-situ stabilization for transit to clinical care and extending the survivability of patients requiring prolonged surgery before blood transfusion. The …

Localization Algorithms For Gnss-Denied And Challenging Environments, Chizhao Yang

Graduate Theses, Dissertations, and Problem Reports (ETD)

In this dissertation, the problem about localization in GNSS-denied and challenging environments is addressed. Specifically, the challenging environments discussed in this dissertation include two different types, environments including only low-resolution features and environments containing moving objects. To achieve accurate pose estimates, the errors are always bounded through matching observations from sensors with surrounding environments. These challenging environments, unfortunately, would bring troubles into matching related methods, such as "fingerprint" matching, and ICP. For instance, in environments with low-resolution features, the on-board sensor measurements could match to multiple positions on a map, which creates ambiguity; in environments with moving objects included, the …

Computational Studies For Extending Understanding Of Complex Droplet Breakup Mechanisms, Caroline Anderson

Electronic Theses and Dissertations, 2020-2023

Conventional methods of classifying droplet breakup are evaluated in the context of unique variation in environmental and droplet fluid conditions. Most characterization is developed for subsonic speeds and Newtonian fluids, so this study extends understanding on how these forms change to a span of applications outside these conditions. Presented examples include the impact effects on hypersonic vehicles travelling through precipitation, where even smallest of rain drops at such speeds can cause damage. Before the droplet even reaches the vehicle, it interacts with the detached bow shock that leads it. Another example of exceptional recent concern is risk of viral transmission …

Simulating Ejecta Blown Off The Lunar Surface Due To Landing Spacecraft Using The Mercury N-Body Integrator, Isabel Rivera

Electronic Theses and Dissertations, 2020-2023

The experiences of the Apollo lunar landings revealed the danger lunar dust can pose to surrounding hardware, outposts, and orbiting spacecraft. Future lunar missions such as the Artemis program will require more information about the trajectories of ejecta blown by landers to protect orbiting spacecraft such as the Lunar Gateway. In this paper, we simulate lunar lander ejecta trajectories using the Mercury N-body integrator. We placed cones of test particles on the Moon at the North Pole, South Pole, and Equator with various ejection speeds and angles. The results show that particles ejected at speeds near the Moon's escape velocity …

Experimental Study Of A Liquid Fuel Bluff Body Flame At Elevated Pressures, Karam Paul

Honors Undergraduate Theses

The purpose of this research was to operate a bluff body flame holder with the objective of stabilizing a flame at elevated pressures over a range of equivalence ratios. The ability to have a ground-based test rig capable of maintaining stable flames at high pressures and temperatures is critical in understanding flames present in modern jet engines and gas turbine technologies. The facility was reconfigured multiple times and the resultant flame was imaged within the optical test section. A converging nozzle was utilized to choke the flow and vary the operating pressures up to 5 atm. By regulating mass flow …

Motor Control System For Near-Resonance High-Cycle Fatigue Testing, Samer K. Armaly

Honors Undergraduate Theses

This research project develops a low-cost high-cycle fatigue (HCF) testing system comprised of an AC motor, variable frequency drive (VFD), eccentric cam, and feedback controller. The system acts as a forced harmonic oscillator leveraging mechanical resonance to vibrate a specimen at a frequency required to induce the testing's strain amplitudes.

This system depends highly on the material being tested. As such, the controller incorporates material characteristics. A frequency sweep measures the strain amplitude to characterize the specimen. Additionally, other measurements such as acceleration can be used as a proxy control variables for strain. A function converts the control variable to …

Optimization Of A Wing Supporting A Coaxial Rotor For Multiple Flight Conditions, Tadd Yeager

Electronic Theses and Dissertations, 2020-2023

Rotor-powered drones continue to grow in popularity in private and government sectors. The use of these drones in challenging environments and in high stakes applications calls for a certain level of robustness and redundancy. Often, these drones are equipped with sets of paired coaxial rotors, which not only improve the performance of the vehicle, but also ensure that a failure of one motor does not constitute the failure of the whole vehicle. Some applications such as extraterrestrial exploration, which use these coaxial rotors, can benefit from a wing shaped rotor arm to reduce drag and increase lift, extending mission lifetime. …

Design Of A Laboratory Annular Combustor, Sathish Dharmalingam, Kartik Dolarkumar Kothari

International Journal of Aviation, Aeronautics, and Aerospace

Combustion lies at the heart of gas turbine technology. The combustor is the power source that aids the acceleration of flight. It provides the core functionality of adding heat through the controlled burn of the air-fuel mixture, converted into mechanical energy with the help of turbines. This extracted power has been used to produce thrust in the case of aircraft or to produce electrical energy in the case of industrial gas turbines. Designing an annular combustor involves a rigorous iterative process, and there is no systematic procedure available to design a small-scale laboratory combustor, used for research and academic purposes. …

Development Of Multi-Scale Characterization Techniques For Stress Corrosion Cracking Of Aerospace Alloys, Nicholas Reed

Electronic Theses and Dissertations, 2020-2023

Corrosion presents an inherent challenge in the safe and effective use of metallic aerospace structures for extended periods of time. Progress in the fundamental understanding of corrosion initiation and propagation under stress requires a multi-scale approach that leverages experiments to develop predictive models. Although there exists a large amount of research results tracking the corrosive processes of anodic dissolution and hydrogen embrittlement, the amount of available data and modeling of the micro-scale initiation of corrosion is sparse. This work leverages a suite of characterization techniques to systematically analyze an aerospace grade aluminum alloy AA7075-T6, providing important multi-scale data for correlation …

Novel Piezo Actuators For Surface Cleaning, Yezad H. Anklesaria

Doctoral Dissertations

"Optical cameras are becoming increasingly common and are used in a variety of applications. With recent progress and transition toward more autonomous systems, the usage of optical systems will be common and widespread. Applications of the optical systems range from autonomous vehicles, home security systems, aviation, extraterrestrial vehicles, spacecraft, and satellites. Imaging systems are used in decision-making in many of these applications. Fouling of the field of view of the imaging system can impede the decision process. An active autonomous cleaning method for the optical surface of the optical systems reliably would be advantageous. The research work focuses on developing …

Dynamic Behavior And Interactions Of Ferrofluid Droplets Under Magnetic Fields In Low Reynolds Number Flows, Md Rifat Hassan

Doctoral Dissertations

Digital microfluidics in combination with emulsion microfluidics are crucial building blocks of droplet-based microfluidics, which are prevalent in a wide variety of industrial and biomedical applications, including polymer processing, food production, drug delivery, inkjet printing, and cell-based assays. Therefore, understanding the dynamics and interactions of droplets as well as the interactions between the droplets and solid surfaces are of great importance in order to improve the performance or product in these applications.

Recently, several studies in the literature have demonstrated the potential of magnetic fields in controlling the behavior of droplets in microscale; however, the fundamental mechanism behind the interesting …

Non-Equilibrium Behavior Of Large-Scale Axial Vortex Cores, Robert L. Ash, Irfan R. Zardadkhan

Mechanical & Aerospace Engineering Faculty Publications

A logical basis for incorporating pressure non-equilibrium and turbulent eddy viscosity in an incompressible vortex model is presented. The infrasonic acoustic source implied in our earlier work has been examined. Finally, this non-equilibrium turbulent vortex core is shown to dissipate mechanical energy more slowly than a Burgers vortex, helping us to explain the persistence of axial vortices in nature. Recent molecular dynamics simulations replicate aspects of this non-equilibrium pressure behavior.

Simulation Of A Trailing Edge Flap Using A Compliant Mechanism, Sam Blackwell

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Parallel Anisotropic Unstructured Grid Adaptation, Christos Tsolakis, Nikos Chrisochoides, Michael A. Park, Adrien Loseille, Todd Michal

Computer Science Faculty Publications

Computational fluid dynamics (CFD) has become critical to the design and analysis of aerospace vehicles. Parallel grid adaptation that resolves multiple scales with anisotropy is identified as one of the challenges in the CFD Vision 2030 Study to increase the capacity and capability of CFD simulation. The study also cautions that computer architectures are undergoing a radical change, and dramatic increases in algorithm concurrency will be required to exploit full performance. This paper reviews four different methods to parallel anisotropic grid adaptation. They cover both ends of the spectrum: 1) using existing state-of-the-art software optimized for a single core and …

Composite-Based Additive Manufacturing Applications In The Polymer Injection Molding Cycle, Cody Bivens

Masters Theses

“The experimental method utilized in this research was the application of composite-based additive manufacturing (CBAM) mold plates in the injection molding process. The mold plates comprised carbon fibers and polyether ether ketone (PEEK) matrix. Modifications were made to the mold plates post manufacturing in order to properly adapt to the rest of the injection molding die. A custom cooling system was engineered and integrated into the injection molding machine for the CBAM mold plates. The polymer processed in the injection molding cycle for this study was Lustran 348 acrylonitrile butadiene styrene (ABS). The result of the trials conducted in this …

Evaluation Of Murrell’S Ekf-Based Attitude Estimation Algorithm For Exploiting Multiple Attitude Sensor Configurations, Sharanabasaweshwara Asundi, Norman Fitz-Coy, Haniph Latchman

Mechanical & Aerospace Engineering Faculty Publications

Pico- and nano-satellites, due to their form factor and size, are limited in accommodating multiple or redundant attitude sensors. For such satellites, Murrell's implementation of the extended Kalman filter (EKF) can be exploited to accommodate multiple sensor configurations from a set of non redundant attitude sensors. The paper describes such an implementation involving a sun sensor suite and a magnetometer as attitude sensors. The implementation exploits Murrell's EKF to enable three sensor configurations, which can be operationally commanded, for satellite attitude estimation. Among the three attitude estimation schemes, (i) sun sensor suite and magnetometer, (ii) magnetic field vector and its …

Influence Of The Inherent Safety Principles On Quantitative Risk In Process Industry: Application Of Genetic Algorithm Process Optimization (Gapo), Mehdi Jahangiri, Abolfazl Moghadasi, Mojtaba Kamalinia, Farid Sadeghianjahromi, Sean Banaee

Community & Environmental Health Faculty Publications

Inherent safety (IS) refers to a set of measures that enhance the safety level of processes and equipment, rendering additional equipment and/or add-ons. The early design phase of processes is suited best for implementation of IS strategies as some of such strategies either are impossible to be implemented at the operation phase or substantially increase costs. The purpose of this study is to present a new approach called genetic algorithm process optimization (GAPO), by which processes can be made inherently safer even at the operation phase. This study simulates the IS principle, assessing its impact on quantitative risk and the …

Time Domain Boundary Element Method Prediction Of Noise Shielding By A Naca 0012 Airfoil, Douglas M. Nark, Fang Q. Hu

Mathematics & Statistics Faculty Publications

As aircraft noise constraints become more stringent and the number/mixture of aircraft configurations grows, it becomes more important to understand the interaction of individual aircraft noise sources with nearby aircraft structures. Understanding these interactions and exploring possible approaches to mitigate or exploit their acoustic impact is essential for overcoming key noise barriers. This paper describes the further validation of a time domain boundary element approach for the prediction of the interactions between incident noise sources and nearby aircraft structures. Predictions were completed for multiple source locations and comparisons of these results with measured data are presented. Overall, very good agreement …