Controls and Control Theory Commons^™

Using An Embedded System For A Quality Cup Of Coffee, Evan Powers, Joshua Stermer, Tsion Yohannes

2023 Symposium

Many coffee lovers spend up to $5 on a cup of coffee everyday. To save money one could make them at home, but a quality machine with PIDs start at $1000. Using an embedded system one could spend less than $50 and a few hours implement PIDs into an existing $400 machine that will last a lifetime. microcontroller. Learning C language combined with hardware implementation applied to cheap and simple everyday objects can improve everyday quality of life and save money.

This is challenging because we have to incorporate the additional circuitry into a pre established circuit with limited space, …

Relaxing Dc Capacitor Voltage Of Power Electronic Converters To Enhance Their Stability Margins, Ali Zakerian

Theses and Dissertations

Recently, due to the increasing adoption of distributed energy resource (DER) technologies including battery energy storage (BES) and electric vehicle (EV) systems, bidirectional power converters are becoming more popular. These converters are broadly utilized as interface devices and provide a bidirectional power flow in applications where the primary power supply can both supply and receive energy. A dc capacitor, called the dc-link, is an important component of such bidirectional converters. For a wide range of applications, the converter is required to control the dc-link voltage. Commonly, a proportional-integrating (PI) controller is used by the dc capacitor voltage controller to generate …

Multiple Objective Co-Optimization Of Switched Reluctance Machine Design And Control, Timothy Burress

Doctoral Dissertations

This dissertation includes a review of various motor types, a motivation for selecting the switched reluctance motor (SRM) as a focus of this work, a review of SRM design and control optimization methods in literature, a proposed co-optimization approach, and empirical evaluations to validate the models and proposed co-optimization methods.

The switched reluctance motor (SRM) was chosen as a focus of research based on its low cost, easy manufacturability, moderate performance and efficiency, and its potential for improvement through advanced design and control optimization. After a review of SRM design and control optimization methods in the literature, it was found …

Control And Design Of A Passive Solar Lumber Drying Kiln, Peter Chardavoyne

Honors Scholar Theses

The passive solar lumber drying kiln design, developed by EE Senior Design Team 2317 is presented, tested, and discussed. The design incorporates solar power and a custom control system to dry 12’ lumber boards inside a shipping container much faster than air-drying methods, which can take up to a year for thorough drying, though this can be extended due to the unpredictability of weather events and conditions. This work presents the design as in the final report provided by the team, but provides a more detailed explanation and analysis of the microcontroller system, testing methods and outcomes, alternate solutions and …

An Isostable Coordinate Based Amelioration Strategy To Mitigate The Effects Of Jet Lag, Talha Ahmed

Masters Theses

Commercial air travel has become extremely commonplace in the last 20 to 30 years especially as the world has moved towards new heights of globalization. Though air travel has greatly reduced transit times allowing people to cover thousand of miles within hours, it comes with its fair share of issues. jet-lag can be regarded to be at the top of those list of problems; jet-lag typically results from rapid travel through multiple time zones which causes a significant misalignment between the person's internal circadian clock and the external time. A person's circadian clock is governed by a population of coupled …

Modeling, Simulation And Control Of Microrobots For The Microfactory., Zhong Yang

Electronic Theses and Dissertations

Future assembly technologies will involve higher levels of automation in order to satisfy increased microscale or nanoscale precision requirements. Traditionally, assembly using a top-down robotic approach has been well-studied and applied to the microelectronics and MEMS industries, but less so in nanotechnology. With the boom of nanotechnology since the 1990s, newly designed products with new materials, coatings, and nanoparticles are gradually entering everyone’s lives, while the industry has grown into a billion-dollar volume worldwide. Traditionally, nanotechnology products are assembled using bottom-up methods, such as self-assembly, rather than top-down robotic assembly. This is due to considerations of volume handling of large …

Deep Reinforcement Learning And Game Theoretic Monte Carlo Decision Process For Safe And Efficient Lane Change Maneuver And Speed Management, Shahab Karimi

All Dissertations

Predicting the states of the surrounding traffic is one of the major problems in automated driving. Maneuvers such as lane change, merge, and exit management could pose challenges in the absence of intervehicular communication and can benefit from driver behavior prediction. Predicting the motion of surrounding vehicles and trajectory planning need to be computationally efficient for real-time implementation. This dissertation presents a decision process model for real-time automated lane change and speed management in highway and urban traffic. In lane change and merge maneuvers, it is important to know how neighboring vehicles will act in the imminent future. Human driver …

Choice Of Instruments For Verification And Calibration Of Gas Analyzers, Ortigali Khakimov, Paraxat Mayliyevna Matyakubova, Mirolim Muhammad O'G'Li Maxmudjonov

Chemical Technology, Control and Management

This article analyzes the process of metrological control of gas analyzers and metrological requirements for them. The current state of the standards used in the state metrological control of gas analyzers and the results of the analyzes were studied. The task of choosing the measuring instruments used in the verification process and optimizing the requirements for them is set. An experimental verification process was organized in three groups using several measuring devices, and the reliability of the verification results was assessed. With the use of modern measuring instruments, a graph of the output value was built during the experimental verification …

Modeling And Adjustment Of A Fuzzy Controller In A Bioreactor Control System, Mahmudov Giyosjon Baqoyevich

Chemical Technology, Control and Management

The article describes the modeling and configuration of a fuzzy controller for the control system of the bacterial oxidation of hard-to-enrich gold-bearing sulfide ores. The simulated logical fuzzy controller allows you to save the consumption of refrigerant water consumed in the process by 4,3%, using it to control the process of bacterial oxidation.

Mathematical Description And Algorithm For Solving The Model Of The Ionite Regeneration Process In The Ion Exchange Method Of Water Softening, Djalolitdin Paxritdinovich Mukhitdinov, Nilufar Abdusami Qizi Yunusova

Chemical Technology, Control and Management

Based on the modern representation of the water softening process by the ion exchange method, modeling was carried out, an algorithm was developed and the ionite regeneration process was calculated in a water softening plant with a fixed ionite layer. To solve the system of equations of the model, special, but simple enough for use in engineering calculations, techniques and methods have been developed and applied. The constructed model and its solution algorithm can be used to predict the process of ionite regeneration in an ion exchange apparatus. It can also be used to calculate the time of the ionite …

Synthesis Methods And Algorithms For Expanding The Dynamic Range Of The Adc, Jumaev Odil Abdujalilovich, Rashidov G'Olibjon Xayriddinovich

Chemical Technology, Control and Management

The modern development of new technologies, in particular, the intensive use of programmable logic integrated circuits in digital information processing tasks, allows for algorithmically and programmatically solving problems, opens up real opportunities to increase accuracy and ensure the required signal conversion speed, and also, it will be possible to take into account the effects of noise and their elimination over the entire time interval band. The article discusses the main methods of digital information processing, analyzes the ways and possibilities of expanding the dynamic range of analog-to-digital converters, as well as the synthesis of appropriate conversion devices, primarily digital filters.

Mathematical Description Of A Bleach Impregnation Reservoir, Bekobod Ibragimov

Chemical Technology, Control and Management

This article discusses the issues of constructing a mathematical model of the technological process of bleaching textile materials in an impregnating reservoir using the heat balance equation, on the basis of which a qualitative analysis of the dynamic properties of an object has been carried out in order to create highly efficient control systems with the use of energy-saving technologies. While constructing a mathematical model characterizing the established and non-established modes of the control object (impregnating reservoir) used changes in heat flow and mass velocity of the incoming tissue. An algorithm for constructing a mathematical model of the process of …

Methods And Algorithms For Monitoring And Prediction Of Various Fire Hazardous Situations, Mizaakbar Xakkulmirzayevich Hudayberdiyev, Oybek Zokirovich Koraboshev

Chemical Technology, Control and Management

This article analyzes emergency situations arising from natural disasters (fires, explosions, earthquakes, floods, landslides, etc.) and man-made accidents. The event in which the values of fire risks in the area decrease uniformly and at the same time the amount of fire risks is minimal is considered optimal. Models, methods, and logistic regression algorithm have been used to predict fire hazard situations and identify potential fire safety measures.

Synergetic Synthesis Of Multivariate Nonlinear Dynamic Objects, Isamiddin Siddikov, Komil Usmanov

Chemical Technology, Control and Management

Based on the synergetic approach, the article solves the problem of analyzing a chemical reactor as a control object and formulates recommendations on the structural and topological synthesis of various control system options. The main feature of technological control objects, in which, as a result of hydromechanical, physical, chemical influences on the flows of the starting substances, their physical properties, state of aggregation and composition change, is their multidimensionality, nonlinearity, multiconnectedness, as well as parametric uncertainty of the mathematical model at the design stage. This type of facility includes a chemical reactor, thermal management, which in most cases is carried …

Remote Alignment Fixing Device With Vizir Marks In Base Lcd Indicator, Nodirbek Rustambekovich Yusupbekov, Zahidov Muratovich Nematjon

Chemical Technology, Control and Management

The article substantiates the needs to increase the level of automation of methods and geodetic support of geometric parameters during the construction of buildings and structures. In particular, the method of alignment measurements is considered. This is widely used in determining deviations from the straightness and alignment of the installation of elements in engineering building structures, including hydraulic structures, as well as in the control of process equipment installations, rolling mills, conveyor lines, crane tracks, when monitoring precipitation. and deformations of techno objects. One of the methods of alignment measurements with the use of a visual-optical device – aliniometer and …

Pole Placement Of Linear Multidimensional Systems Using Unlimited Rank Output Feedback, Jasur Usmonovich Sevinov, Okila Khusanovna Boeva

Chemical Technology, Control and Management

The problem of placing poles in linear multidimensional systems using a feedback matrix of unlimited rank is considered. The effect of output feedback of indefinite rank of the characteristic polynomial of a system with several variables is studied. The results are then used to obtain a recurrent pole placement algorithm without any restrictions on the rank of the output feedback matrix used. The algorithm is based on the pseudo-inverse concept of obtaining solutions to systems of linear equations using the least squares method and is computationally efficient.

Development Of A Fish Robot Equipped With Novel 3d-Printed Soft Bending Actuators, Steven Steele, Jorge Diaz Rodriguez, Sharun Sripathy, Turaj Ashuri, Saleh Gharaie, Yusun Chang, Amir Ali Amiri Moghadam

Symposium of Student Scholars

This paper reports on design and fabrication of a novel soft fish robot. Application of soft actuators for the fish tail will generates continuum bending motion which resembles the natural motion of the fish. However, most soft actuator mechanisms are complex and have low efficiency. Thus, to address this issue we have developed a 3D printed soft bending actuator which can be actuated with an electromotor. The basic design idea of the soft bending actuator is explained, and iteration of the design showed to create the desired motion for the soft tail. The soft actuator has been successfully integrated with …

Exploration Of Force In Movement And Perception In Parkinson’S Disease, Caroline Stefanie Aitken

Electronic Thesis and Dissertation Repository

Parkinson’s Disease (PD) causes force control deficits in upper and lower limbs. About 50% of patients with advanced PD develop freezing of gait (FOG). There is limited research comparing force control in PD with and without FOG, especially in upper limbs. It has been suggested that motor control deficits in PD are related to deficits in kinesthesia, but there is conflicting evidence whether levodopa alleviates kinesthetic deficits. In this thesis, force control was explored using an upper-and-lower-limb haptics-enabled robot in a reaching task, and kinesthesia was investigated using a haptic device in a force discrimination task while participants were on …

Implementation Of Static Rfid Landmarks In Slam For Planogram Compliance, Brennan L. Drake

Honors College Theses

Autonomous robotic systems are becoming increasingly prevalent in everyday life and exhibit robust solutions in a wide range of applications. They face many obstacles with the foremost of which being SLAM, or Simultaneous Localization and Mapping, that encompasses both creation of the map of an unknown environment and localization of the robot in said environment. In this experiment, researchers propose the use of RFID tags in a semi-dynamic commercial environment to provide concrete landmarks for localization and mapping in pursuit of increased locational certainty. With this obtained, the ultimate goal of the research is to construct a robotics platform for …

Data-Driven Stochastic Optimal Control Using Hilbert Space Embeddings Of Distributions, Adam J. Thorpe

Electrical and Computer Engineering ETDs

Autonomous systems are increasingly being deployed in complex environments subject to real-world uncertainty. For such systems, it may be exceptionally difficult or even impossible to compute a simple mathematical model of the system--for instance due to the presence of human elements, complex mechanics or system dynamics, or learning-enabled components. Data-driven control has recently gained significant attention in this area, where observations taken from the system evolution are used to compute an implicit representation of the system that is amenable to analysis and control. However, data-driven algorithms for control present new challenges, and require new insights to enable their use. The …

Chatgpt As Metamorphosis Designer For The Future Of Artificial Intelligence (Ai): A Conceptual Investigation, Amarjit Kumar Singh (Library Assistant), Dr. Pankaj Mathur (Deputy Librarian)

Library Philosophy and Practice (e-journal)

Abstract

Purpose: The purpose of this research paper is to explore ChatGPT’s potential as an innovative designer tool for the future development of artificial intelligence. Specifically, this conceptual investigation aims to analyze ChatGPT’s capabilities as a tool for designing and developing near about human intelligent systems for futuristic used and developed in the field of Artificial Intelligence (AI). Also with the helps of this paper, researchers are analyzed the strengths and weaknesses of ChatGPT as a tool, and identify possible areas for improvement in its development and implementation. This investigation focused on the various features and functions of ChatGPT that …

Simple Open-Source Formal Verification Of Industrial Programs, Christopher Disney Peterson

Master's Theses

Industrial programs written on Programmable Logic Controllers (PLCs) have become an essential component of many modern industries, including automotive, aerospace, manufacturing, infrastructure, and even amusement parks. As these safety-critical systems become larger and more complex, ensuring their continuous error-free operation has become a significant and important challenge. Formal methods are a potential solution to this issue but have traditionally required substantial time and expertise to deploy. This usability issue is compounded by the fact that PLCs are highly proprietary and have substantial licensing costs, making it difficult to learn about or deploy formal methods on them.

This thesis presents the …

Method For Solving The Kinematics Inverse Problem For Moving Along A Trajectory Objects (As An Example Of Assembly Industrial Robots), Oripjon Olimovich Zaripov, Dildora Usmonovna Sevinova

Chemical Technology, Control and Management

The task of performing a technological operation in kinematic calculation of industrial robots and determining various kinematic parameters describing the efficiency of robots is solved. Among them, one of the urgent problems based on the analysis of the entire kinematics of the assembly industrial robot is the problem of solving the inverse problem of the kinematics of the manipulator positions, that is, the problem of determining the relative parameters that change the coordinates of the gripper according to the given position. The article presents a scheme that allows solving the inverse kinematics problem of an industrial robot manipulator moving in …

Algorithms For Multi-Factory Polynomial Modeling Of Technological Processes, Farrukh Do'stmirzayevich Jo'rayev, Murodjon Ashurqulovich Ochilov

Chemical Technology, Control and Management

The article reveals the meaning and essence of the modeling method in the study of complex technological processes based on the problematic aspects of building multifactorial relationships and the principles for their elimination. In the case of non-linearity of multifactorial connections of a complex system, the expediency of approximating such functions by polynomials is substantiated. The authors' ideas about the increasing importance of interpolation methods in practice against the background of the possibility of simplification based on the use of modern mathematical hardware and software for integration into the process of modeling and optimizing technological processes due to the complexity …

Virtual Potassium Chloride Analyzer In The System Of Advanced Control Of Potash Fertilizer Production Processes, Umidjon Ruziev, Jahongir Sherboyevich Bekqulov

Chemical Technology, Control and Management

It is proposed to include virtual instrumental quality analyzers of potash fertilizers in the composition of the advanced (advanced) management system. The structure of the virtual analyzer is substantiated using mathematical models of the technological process of drying potassium chloride in its composition. Based on the results of fuzzy clustering, the parameters of the modes of the technological process of drying potassium chloride are determined.

Influence Of Magnetomechanical Properties Of Ferromagnetic Materials On The Sensitivity Of A Magnetoelastic Sensor, Sulton Amirov, Kamila Komilovna Jurayeva

Chemical Technology, Control and Management

The requirements of high operational reliability are most fully met by automated monitoring and control systems, the elements of which are magnetoelastic sensors. Such sensors, due to their metrological characteristics, have found application in electrified railway transport, in the metallurgical, metalworking, mining and other industries. The principle of operation of such sensors is based on the fact that in the process of influencing the magnetic core of the sensor by force, there is a change in the magnetic permeability of the material, a change in the magnetic resistance of the circuit, a change in the mutual inductance coefficient of the …

Structural Model Of The Technological Process Of Storage And Processing Of Oil Raw Materials, N.A Kabulov

Chemical Technology, Control and Management

The technological method of storing and processing oilseed raw materials is structurally modelled in the article. Additionally, it is suggested that the generalized structure be presented as a three-part scheme, consisting of a raw material department, a processing shop, and transportation networks. On the basis of a thorough examination of the characteristics of the constituent parts of the technological complex, a practical model for the problem of the general characteristics of the technological complex is proposed.

Algorithmic Methods For Developing The Structure Of A Thyristor Electric Drive For Mining Machines, N.R Yusupbekov, O.A. Jumaev, S.S. Turaev

Chemical Technology, Control and Management

The article discusses the creation of algorithmic structures and the development of digital control systems for electric drives of mine-lifting machines, provides some concepts for creating digital control systems using thyristor converters. The analysis of the static volt-ampere characteristics of the thyristor is given, some calculations of the circuits and circuits of the thyristor converter (TP) corresponding to the different modes of operation of the TP are given, and also, based on the synthesis of the dynamic properties and characteristics of the thyristor, an algorithmic structure of the model of the thyristor converter is proposed.

Analysis Of Vegetable Oil Refining Technology, Elyor Samadov

Chemical Technology, Control and Management

Innovative technologies for refining vegetable oils are presented, as well as the qualitative characteristics of raw vegetable oils obtained by extraction and mechanical methods. A general review of the chemical composition and impurities of vegetable oils resulting from the reaction between glycerol and fatty acids is carried out, and a brief review of the study to determine the effect of refining on biologically active components.

The analytical review is devoted to a comparative comparison of two types of refining - chemical and physical refining.

Synchronization Of The Training Of Specialists In The Automation Of Technological Processes In Accordance With The Dynamics Of The Taxonomy Of Learning Goals, Yusuf Shodievich Avazov, Kamola Abdullaeva

Chemical Technology, Control and Management

Changes in the characteristics of modern ones, reflecting them as the "digital generation", inevitably necessitate electronic interactive, mobile and mixed, machine learning, especially in the field of automation and control of technological processes and production. As a consequence of reflecting these realities, there have been parallel changes in the taxonomy of learning objectives - from the classical to the revised rethought and digital.

In order to study the problem of synchronizing the training of future specialists in the field of automation and control of technological processes and production and funny knowledge in accordance with the dynamics of the taxonomy of …