Controls and Control Theory Commons^™

Design And Fabrication Of A Force-Displacement Control Mechanism For Bone-Surgical Tool Testing, Kenneth Nwagu

Electronic Theses and Dissertations

This project focuses on the design and fabrication of an experimental setup for orthopedic-tool testing, tailored for a surgical instrumentation company. The multifaceted project encompasses a literature review, conceptual design, prototyping, and rigorous testing, resulting in a versatile control system capable of assessing various orthopedic tools, including bone drills, saws, burrs, and power handpieces.

Orthopedic surgical procedures (which include cutting and/or drilling into bone) often need to be performed on bones for faster recovery. The drilling and cutting process can cause an increase in temperature at the cutting site which can cause bone necrosis. The tools also need to be …

Manual Material Handling Lift-Assist System For Occupational Exoskeleton, Erik Goes, Daniel Guthrie, Trevor Ward

Honors Capstones

It is no secret that lifting heavy objects is one of the premier causes of workplace injury, and the modern worker needs help to remain healthy. Workers need something they always have with them that makes their work safer as well as easier; our solution is an active lift-assist exoskeleton. The proposed exoskeleton design includes a military backpack exoskeleton frame, on which two actuators pull cables attached to end effectors that the operator will be holding. This system can adjust to conform to a wide variety of operator sizes, without restricting any of their range of motion. This leads to …

Design And Control Of A Peristaltic Pump To Simulate Left Atrial Pressure In A Conductive Silicone Model, Jeremy Collins

Mechanical Engineering Undergraduate Honors Theses

According to the CDC, atrial fibrillation is responsible for more than 454,000 hospitalizations and approximately 158,000 deaths per year. A common treatment for atrial fibrillation is catheter ablation, a process in which a long flexible tube is guided through the femoral artery and to the source of arrhythmia in the heart, where it measures the electrical potential at various locations and converts problematic heart tissue to scar tissue via ablation. This paper details the design and control of a low-cost ($400) peristaltic pump system using repetitive control to replicate blood pressure in the left atrium in a conductive silicone model …

Integration Of Robotic And Electro-Pneumatic Systems Using Advanced Control And Communication Schemes, Chinmay Kondekar

Dissertations, Master's Theses and Master's Reports

Modern industrial automation systems are designed by interconnecting various subsystems which work together to perform a process. The thesis project aims to integrate fragmented subsystems into a flexible and reconfigurable system through advanced communication protocols and perform a process to demonstrate the effectiveness of interconnected systems.

The system consists of three six-axis robots, one electro-pneumatic robot, and two conveyors connected using EthernetIP communication and hardwired connections. The interconnected system works together to perform machining of a workpiece using advanced control methods of CAD to robot path generation, central control through a PLC, and process control through HMI.

Standardized programming blocks …

Advanced Mechatronics, Hao Su

Open Educational Resources

Project-based course on the design of mechatronic devices to address needs identified by hospital-based clinicians and industry. Students work in teams to develop a mechatronic prototype. The lectures will cover the design of medical devices and robotics including sensors, actuators, and robots. The students will communicate with customers to understand design needs, then conduct study on prior art, intellectual property, due diligence, and idea conceptualization. Students will present ideas in class and to a broad audience from local industry. Students will also write a publication-quality final report, which they will be encouraged for publication submission.

Engineering Design I, Hao Su

Open Educational Resources

Introduction to robotics

Cal Poly Supermileage Electronic Fuel Injection, Alexander Pink

Electrical Engineering

Cal Poly Supermileage is a student-run engineering club that builds prototype gasoline vehicles optimized maximum fuel-efficiency. To power their vehicles, the Supermileage team makes use of single-cylinder, 4-stroke, electronically fuel-injected (EFI) gasoline engines. This report details the development, iterative design & test cycles, and integration of an EFI system for the Supermileage club. This project develops an EFI system that interfaces to the most common types of sensors found in the low-power Supermileage-range of engines, including throttle-position sensors, manifold absolute pressure sensors, gear-tooth hall-effect sensors, variable-reluctance position sensors, engine coolant temperature sensors, intake air temperature sensors, and exhaust oxygen sensors. …

Telepresence: Design, Implementation And Study Of An Hmd-Controlled Avatar With A Mechatronic Approach, Darren Michael Chan

Master's Theses

Telepresence describes technologies that allow users to remotely experience the sensation of being present at an event without being physically present. An avatar exists to represent the user whilst in a remote location and is tasked to collect stimuli from its immediate surroundings to be delivered to the user for consumption. With the advent of recent developments in Virtual Reality technology, viz., head-mounted displays (HMDs), new possibilities have been enabled in the field of Telepresence. The main focus of this thesis is to develop a solution for visual Telepresence, where an HMD is used to control the direction of a …

Mechatronics Application To Solar Tracking, Danny L. Rodriguez Jr

Purdue Polytechnic Directed Projects

The purpose of this was to design and implement a two-axis solar tracking system utilizing the National Instruments C-Rio real time controller. In order to accomplish this a prototype was modeled in CAD. This prototype used two 12 V DC motors to change a solar panel's rotation and tilt based on feedback data from three cadmium sulfide photoresistors. This configuration was chosen for its ability to create both a left-right rotational and an up/down tilt differential. In Addition this approach uses National Instruments Labview to control a solar tracking system. Using Labview add uniqueness to this project by adding a …