Controls and Control Theory Commons^™

Applications Of Supercapacitors In Robotic Systems, Charles Davis, Zachary Giese, Joseph Gober, Samuel Grisham, Avery Mahan

ATU Research Symposium

This project explores the utilization of a bespoke supercapacitor system to energize and propel a robot across various challenging courses. The custom supercapacitor setup serves as the primary power source, providing rapid charging capabilities and high energy density. The research investigates the integration of this innovative power solution into the robot's design, aiming to optimize its performance and endurance in competitive environments.

Plc Course Development, Leonard Hernandez, Jacqueline Grace Radding

Electrical Engineering

The goal of this project is to design and construct the first lab experiment for the newly developed EE435 laboratory course. The experiment entails PLC programming to automate LED lighting in a simulated building. Starting with why PLCs are used, how to use the interface of EcoStruxure Control Expert V15.0 and practice using logic to control the dimming of a Light Emitting Diode (LED) to sustain a certain number of lumens consistent in a zone. Through the lab manual developed in this project, students will gain experience of creating logic designs using Function Block Diagram (FBD) and learn the layout …

Study Of Dynamic Characteristics Of The Mechanical Circuit Of The Developed Induction Inertial Vibration Transducer, Sulton Fayzullayevich Amirov, Asror Abdunabiyevich Shoimkulov

Chemical Technology, Control and Management

The article examines the dynamic characteristics of the mechanical circuit of the developed induction vibration transducer. It is found that in the investigated transducers forced oscillations occur with the frequency of the input disturbing force, the amplitude of forced oscillations does not depend on the initial conditions and time, and in forced oscillations with damping there is always a shift of the oscillation phase compared to the phase of the input disturbing force. It is shown that the induction vibration transducer reproduces the measured vibrations with small distortions only in a relatively narrow frequency region at frequencies of the input …

Smart System For Wheat Diseases Early Detection, Rustam Baratov, Himola Sunnatillayeva, Almardon Mamatovich Mustafoqulov

Chemical Technology, Control and Management

This paper presents a smart system for early detection of wheat plant diseases in the vegetation period. The proposed smart system allows detecting three types of wheat diseases, particularly yellow rust, powdery mildew and septoria at early stage and significantly improves the soil and ecology by locally spraying harmful chemicals just to sickness plants. The proposed diagnostic program is created in the C++ programming language. The basic structure of the smart system consists of Raspberry PI 4 MODULE, Logitech HD Pro Webcam C920, buzzer, HC-SR04 distance sensor, DC motor driver, AC motor, power supply, relay and some digital devices.

Static And Dynamic State Estimation Applications In Power Systems Protection And Control Engineering, Ibukunoluwa Olayemi Korede

Doctoral Dissertations

The developed methodologies are proposed to serve as support for control centers and fault analysis engineers. These approaches provide a dependable and effective means of pinpointing and resolving faults, which ultimately enhances power grid reliability. The algorithm uses the Least Absolute Value (LAV) method to estimate the augmented states of the PCB, enabling supervisory monitoring of the system. In addition, the application of statistical analysis based on projection statistics of the system Jacobian as a virtual sensor to detect faults on transmission lines. This approach is particularly valuable for detecting anomalies in transmission line data, such as bad data or …

Cyber-Threat Detection Strategies Governed By An Observer And A Neural-Network For An Autonomous Electric Vehicle, Douglas Scruggs

All Theses

A pathway to prevalence for autonomous electrified transportation is reliant upon accurate and reliable information in the vehicle’s sensor data. This thesis provides insight as to the effective cyber-attack placements on an autonomous electric vehicle’s lateral stability control system (LSCS). Here, Data Integrity Attacks, Replay Attacks, and Denial-of-Service attacks are placed on the sensor data describing the vehicle’s actual yaw-rate and sideslip angle. In this study, there are three different forms of detection methods. These detection methods utilize a residual metric that incorporate sensor data, a state-space observer, and a Neural-Network. The vehicle at hand is a four-motor drive autonomous …

Mathematical Model Of An Industrial Robot Built On The Basis Of Linear Motion Mechatron Modules, Matyokubov Nurbek Rustamovich, Rakhimov Temurbek Omonboyevich

Chemical Technology, Control and Management

The use of Industry 4.0 technologies in modern production serves to increase production efficiency. Robots and robotic complexes with innovative intelligent control are widely used in industrial production. However, studying their mechanical part, linear motion mechatronic modules and control system is a complex object. The variety and complexity of control methods and operating modes negatively affects the operator's working time and production productivity. In such cases, it is necessary to improve control methods and develop technologies used in industry, including robots and robotic manipulators, which allow to perform short movements with high accuracy and speed. In the article, the mathematical …

The Application Of Model Predictive Control On Paralleled Converters For Zero Sequence Current Suppression And Active Thermal Management, Justin Dobey

All Theses

In the field of power electronics, the control of rectifiers is a crucial area of study. Rectifiers are used to convert AC power into DC power, and are commonly used in a wide range of applications, including renewable energy systems, industrial automation, and consumer electronics. However, in medium and high-power systems when multiple rectifiers are connected in parallel to a DC bus, stability issues can arise, including voltage fluctuations, zero sequence circulating current, and thermal imbalance.

Achieving stable DC bus voltage is essential for maintaining the proper functioning of electronic devices, while suppressing zero sequence current is necessary for protecting …

Development Of A Soft Robotic Approach For An Intra-Abdominal Wireless Laparoscopic Camera, Hui Liu

Doctoral Dissertations

In Single-Incision Laparoscopic Surgery (SILS), the Magnetic Anchoring and Guidance System (MAGS) arises as a promising technique to provide larger workspaces and field of vision for the laparoscopes, relief space for other instruments, and require fewer incisions. Inspired by MAGS, many concept designs related to fully insertable magnetically driven laparoscopes are developed and tested on the transabdominal operation. However, ignoring the tissue interaction and insertion procedure, most of the designs adopt rigid structures, which not only damage the patients' tissue with excess stress concentration and sliding motion but also require complicated operation for the insertion. Meanwhile, lacking state tracking of …

Round Trip Time Measurement Over Microgrid Power Network, Yasin Emir Kutlu, Ruairí De Fréin, Malabika Basu, Ali Malik

Conference papers

A focus of the Power Systems and Networking communities is the design and deployment of Microgrid (MG) integration systems that ensure that quality of service targets are met for load sharing systems at different endpoints. This paper presents an integrated Microgrid testbed that allows Microgrids endpoints to share their current, voltage and power values using a Network Published Shared Variable (NPSV) approach. We present Round Trip Time (RTT) measurements for time sensitive Microgrid control traffic in the presence of varying background traffic as an example quality of service measurement. Numerical results are presented using a range of different background traffic …

Crazyflie 2.1 Quadcopter Nonlinear System Identification, Nhat V. Nguyen, Hope Storro, John Plimpton

2023 Symposium

Quadcopters (quad) are used widely in many industries with crucial applications such as infrastructure inspection or package delivery. The Crazyflie 2.1 quad from Bitcraze provides an excellent platform for research and development. In this project, our goal is to perform system identification on the Crazyflie to propose a complete model. A gray box method is explored, which includes leveraging the parameters that are already known, to develop a set of equations. Through theory, simulations, and measurements, a complete quadcopter model is developed.

Hvac Fan Cooling System Using Modicon M580, Ogbonnaya Okoronkwo Okorie, Nicolas Jens Fache

Electrical Engineering

A common problem that many devices have when operating is overheating. Whether it is operating at full capacity or idle, those devices that we use exert heat to some type of extent. The physical and electronic components of the device can only withstand so much heat before the component becomes damaged. This product provides a method of preventing overheating by being a cooling system for your device. A solution for preventing overheating of the components in these electronic devices is by having some sort of cooling system. Our product’s cooling system will be based on energy efficiency, which means that …

Programmable Vibration Table Retrofit With Eagle Medical, Jonathan Ilagan, Madhav Asok, Max Lewter

Biomedical Engineering

This project aimed to repair and upgrade a vibration table used for package testing for the sponsor, Eagle Medical - a medical packaging and sterilization company based in Paso Robles, California. The current vibration table is not programmable and lacks circuit diagrams, making it difficult to repair. In addition, it is not functional due to internal circuitry issues and power requirements. To address these issues, the team will implement several upgrades to improve the product and allow for better random cyclic vibration testing. A full assessment of the existing vibration table will be conducted to ensure the viability of these …

Instrumented Control Column For Optionally Piloted Aircraft, Andrew J. Klein

Electrical Engineering

Natilus, an aerospace company that is rapid-prototyping optionally piloted aircraft (OPA) for the shipping industry, needs a system that retrieves control column position data in order to manipulate flight simulator parameters in software. At present, a universally compatible system for all aircraft does not exist. Typically, established aerospace companies will sink significant time and money into developing proprietary systems for control column data retrieval as every aircraft is unique in its layout and linkage design. However, as a startup developing their first aircraft, Natilus does not have the privilege of modifying an existing sensor system to work with their HIL …

Using An Embedded System For A Quality Cup Of Coffee, Evan Powers, Joshua Stermer, Tsion Yohannes

2023 Symposium

Many coffee lovers spend up to $5 on a cup of coffee everyday. To save money one could make them at home, but a quality machine with PIDs start at $1000. Using an embedded system one could spend less than $50 and a few hours implement PIDs into an existing $400 machine that will last a lifetime. microcontroller. Learning C language combined with hardware implementation applied to cheap and simple everyday objects can improve everyday quality of life and save money.

This is challenging because we have to incorporate the additional circuitry into a pre established circuit with limited space, …

Multiple Objective Co-Optimization Of Switched Reluctance Machine Design And Control, Timothy Burress

Doctoral Dissertations

This dissertation includes a review of various motor types, a motivation for selecting the switched reluctance motor (SRM) as a focus of this work, a review of SRM design and control optimization methods in literature, a proposed co-optimization approach, and empirical evaluations to validate the models and proposed co-optimization methods.

The switched reluctance motor (SRM) was chosen as a focus of research based on its low cost, easy manufacturability, moderate performance and efficiency, and its potential for improvement through advanced design and control optimization. After a review of SRM design and control optimization methods in the literature, it was found …

Control And Design Of A Passive Solar Lumber Drying Kiln, Peter Chardavoyne

Honors Scholar Theses

The passive solar lumber drying kiln design, developed by EE Senior Design Team 2317 is presented, tested, and discussed. The design incorporates solar power and a custom control system to dry 12’ lumber boards inside a shipping container much faster than air-drying methods, which can take up to a year for thorough drying, though this can be extended due to the unpredictability of weather events and conditions. This work presents the design as in the final report provided by the team, but provides a more detailed explanation and analysis of the microcontroller system, testing methods and outcomes, alternate solutions and …

Implementation Of Static Rfid Landmarks In Slam For Planogram Compliance, Brennan L. Drake

Honors College Theses

Autonomous robotic systems are becoming increasingly prevalent in everyday life and exhibit robust solutions in a wide range of applications. They face many obstacles with the foremost of which being SLAM, or Simultaneous Localization and Mapping, that encompasses both creation of the map of an unknown environment and localization of the robot in said environment. In this experiment, researchers propose the use of RFID tags in a semi-dynamic commercial environment to provide concrete landmarks for localization and mapping in pursuit of increased locational certainty. With this obtained, the ultimate goal of the research is to construct a robotics platform for …

Enhancing Traffic Safety In Unpredicted Environments With Integration Of Adas Features With Sensor Fusion In Intelligent Electric Vehicle Platform With Implementation Of Environmental Mapping Technology, David S. Obando Ortegon

Electronic Theses and Dissertations

A major objective on society is to reduce the number of accidents and fatalities on the road for drivers, and pedestrians. Therefore, the automotive engineering field is working on this problem through the development and integration of safety technologies such as advanced driving assistance systems. For this reason, this work was intended to develop and evaluate the performance of different ADAS features and IV technologies under unexpected scenarios. This by the development of safety algorithms applied to the intelligent electric vehicle designed and built in this work, through the use of ADAS sensors based on sensor fusion. Evaluation of AEB, …

Design And Fabrication Of A Force-Displacement Control Mechanism For Bone-Surgical Tool Testing, Kenneth Nwagu

Electronic Theses and Dissertations

This project focuses on the design and fabrication of an experimental setup for orthopedic-tool testing, tailored for a surgical instrumentation company. The multifaceted project encompasses a literature review, conceptual design, prototyping, and rigorous testing, resulting in a versatile control system capable of assessing various orthopedic tools, including bone drills, saws, burrs, and power handpieces.

Orthopedic surgical procedures (which include cutting and/or drilling into bone) often need to be performed on bones for faster recovery. The drilling and cutting process can cause an increase in temperature at the cutting site which can cause bone necrosis. The tools also need to be …

Diy Cell Incubator, Hayden James Jeanor

Electrical Engineering

The purpose of creating a cell Incubator is for the development of cell and tissue production in laboratory settings. Large scale research projects and the medical community grow cells for various reasons, including experiments and creating tissue for patients. However, they cannot simply depend on growing cells in a petri dish that sit on a rack at room temperature. To grow heathy cells in the fastest way possible, they use cell incubators. Cell incubators create an atmosphere within the incubation bay that is designed to promote cell growth. The three main components that need to be constantly regulated, using a …

Multi-Criteria Performance Evaluation And Control In Power And Energy Systems, Payam Ramezani Badr

All Dissertations

The role of intuition and human preferences are often overlooked in autonomous control of power and energy systems. However, the growing operational diversity of many systems such as microgrids, electric/hybrid-electric vehicles and maritime vessels has created a need for more flexible control and optimization methods. In order to develop such flexible control methods, the role of human decision makers and their desired performance metrics must be studied in power and energy systems. This dissertation investigates the concept of multi-criteria decision making as a gateway to integrate human decision makers and their opinions into complex mathematical control laws. There are two …

Hypoxic Incubation Chamber, Simone Lisette Helfrich, Makenzie Nicole Jones

Biomedical Engineering: Graduate Reports and Projects

This paper describes the design, manufacturing, and testing of a novel controllable hypoxic incubator with fully functional oxygen gas control and temperature control in a humid environment. On the current market, a majority of the few hypoxic incubators use pre-mixed gas that does not offer precise control over gas concentration. The objective for this project was to create a chamber that allows the user to set the O2 concentration to varying set points of % O2 while maintaining the chamber at a constant body temperature, CO2 level, humidity, and sterility. To start the project, multiple concepts were developed for the …

Hypoxic Incubation Chamber, Simone Lisette Helfrich, Makenzie Nicole Jones

Master's Theses

This paper describes the design, manufacturing, and testing of a novel controllable hypoxic incubator with fully functional oxygen gas control and temperature control in a humid environment. On the current market, a majority of the few hypoxic incubators use pre-mixed gas that does not offer precise control over gas concentration. The objective for this project was to create a chamber that allows the user to set the O2 concentration to varying set points of % O2 while maintaining the chamber at a constant body temperature, CO2 level, humidity, and sterility. To start the project, multiple concepts were developed for the …

Three-Phase Ac Induction Motor Speed Control Based On Variable Speed Driver, Abdelrahim Ahmed Mohammed Ate, Rihab Gafar, Xiuyun Sun, Tahleel Abozead

Makara Journal of Technology

Massive loss of power is a concern for many countries because of the high power consumption of alternating current (AC) motors. The motor speed should be controlled to alleviate this problem and save more power. This paper proposes a simple simulation for a variable speed driver (VSD) to control the three-phase induction motor speed. The VSD consists of three parts. The converter performs from full bridge diodes to convert single-phase AC voltage into direct current voltage, and then this voltage is filtered by the RL filter and transferred to the last part, which is the inverter. The model was simulated …

Stability Analysis And Design Of Grid-Interactive Power Electronic Converters, Le Kong

Doctoral Dissertations

The increasing penetration of power electronic converters (PECs) can provide high flexibility, full controllability, sustainability, and improved efficiency for future electric power systems. However, it also introduces new challenges since the wide-frequency-band control dynamics of PECs can interact with the power system and result in different types of instability issues. To holistically address the instability issues, several research activities are conducted in this dissertation.

The modular multilevel converter (MMC), which is one of the most common PECs in high- or medium-voltage power systems, is investigated. An improved MMC dc impedance model is developed by considering both the submodule voltage and …

Hybrid Smart Transformer For Enhanced Power System Protection Against Dc With Advanced Grid Support, Moazzam Nazir

All Dissertations

The traditional grid is rapidly transforming into smart substations and grid assets incorporating advanced control equipment with enhanced functionalities and rapid self-healing features. The most important and strategic equipment in the substation is the transformer and is expected to perform a variety of functions beyond mere voltage conversion and isolation. While the concept of smart solid-state transformers (SSTs) is being widely recognized, their respective lifetime and reliability raise concerns, thus hampering the complete replacement of traditional transformers with SSTs. Under this scenario, introducing smart features in conventional transformers utilizing simple, cost-effective, and easy to install modules is a highly desired …

Smartphone Control Of Rc Cars, Weston R. Fitzgerald

Electrical Engineering

The smartphone-controlled RC (remote-controlled) car is an inexpensive remote-controlled car designed to be fast and portable. Instead of manufacturing, packaging, and shipping a separate controller, the remote control is implemented in a phone application, which saves time and money in both the design process and the manufacturing process. Utilizing the user’s smartphone is more cost-effective since mobile devices are a common recurrence, and packaging fewer devices results in overall better portability of the product.

This smartphone-controlled car is speedy and intuitive to learn for typical smartphone users. The user can change the car’s speed and direction wirelessly using their phone; …

Analysis And Optimization Of The Two-Phase Series Capacitor Buck Dc-Dc Converter, Salahaldein Ali Aboajila Ahmed

Graduate Theses and Dissertations

Current sharing schemes for conventional multi-phase converters are based on sensing each phase current to deliver the current information to their controllers. In conventional buck converters, this fact may require a preset current sharing ratio at the expense of efficiency, which eventually requires a larger sensing circuit to achieve the sensing accuracy of each phase. Introducing the concept of automatic current sharing is one of the solutions to tackle this issue. Automatic current sharing (Current Sharing Mechanism CSM) is an advanced way to distribute heat generation in multi-phase switching topologies at full load. A two-phase series capacitor buck converter (2-pscB) …

Automatic Testing Of Organic Strain Gauge Tactile Sensors., Brian P. Goulet

Electronic Theses and Dissertations

Human-Robot Interaction is a developing field of science, that is posed to augment everything we do in life. Skin sensors that can detect touch, temperature, distance, and other physical interaction parameters at the human-robot interface are very important to enhancing the collaboration between humans and machines. As such, these sensors must be efficiently tested and characterized to give accurate feedback from the sensor to the robot. The objective of this work is to create a diversified software testing suite that removes as much human intervention as possible. The tests and methodology discussed here provide multiple realistic scenarios that the sensors …