Other Mechanical Engineering Commons^™

The Critical Role Of Dynamic Surface Tension Of Surfactants On The Impact Dynamics Of Water Droplets, Amir Esmaeili, Reza Mohammadi

Graduate Research Posters

Due to their time-dependent surface tension, the addition of surface-active agents or surfactants to water for specific applications has made controlling the impact dynamics of these droplets a complex phenomenon. This work investigates the influence of the molecular weight, concentration, and ionic nature of the surfactants as well as the substrate surface characteristics on the impact dynamics of surfactant-laden droplets using a high-speed camera at 10000 frames per second. Sodium dodecyl sulfate, hexadecyltrimethylammonium bromide, and n-decanoyl-n-methylglucamine were used as anionic, cationic, and nonionic surfactants, respectively. We used hydrophilic glass slides, hydrophobic polytetrafluoroethylene, and superhydrophobic alkyl ketene dimer (AKD) as substrates. …

On The Improvement Of The Indirect Quantification Of Methane Emissions: A Stationary Single Sensor Approach, Robert Scott Heltzel

Graduate Theses, Dissertations, and Problem Reports (ETD)

There is a need for improved indirect quantification of methane emissions, particularly from the natural gas industry. Natural gas production continues to increase along with the number of wells and production sites. These production sites have the potential to contribute significant levels of methane emissions. Methane is a potent greenhouse gas and the primary component of natural gas. A more complete understanding of emissions through improved quantification will lead to enhanced mitigation. Emissions have historically been quantified with both direct and indirect methods, with varying results. Emissions have been shown to be both temporally and spatially variable. These facts have …

Performance And Economical Analysis Of Different Insulating Materials Used To Reduce The Heat Load Of An Existing Residential Building, Radwa A. El-Awadly, Ahmed A. Abdel-Rehim

Mechanical Engineering

The energy consumption from the residential sector is an important element which has an impact on the total energy consumption in any country. The heating and air conditioning loads can be reduced through many means. Using thermal insulation in buildings does not only contribute in reducing the required air conditioning system size, but also in reducing the annual energy cost for the whole building. In this case, the energy saving varies according to the building type, the climatic conditions at which the building is located as well as the type of the insulating material used. In the present study, an …

A Combined Study Of Heat Transfer And Temperature Distribution Inside Heated Double-Wall Infant Incubator Using Cfd, Hesham Safwat

Mechanical Engineering

What will be the answer if someone tried walking on the street and asking ten mothers in which pregnancy month their child had been born? The answer will be shocking because according to World Health organization (WHO 2012) at least one out of those ten mothers will answer that her kid was born earlier than his/her time! There are more than 15 million premature babies in the world having their first breath every year earlier than their times and more than 1.1 million of them the first few breaths unfortunately become their last. Moreover, if this question is asked to …

Cfd Investigation Of The Optimal Ventilation System For A Single-Family Room Neonatal Intensive Care Unit, Hesham Safwat, Ahmed Elbaz

Mechanical Engineering

Newborns are immunocompromised, and they are more susceptible to get infected than elders, hence, they should be kept in an aseptic environment that is almost free of microorganisms. A neonatal intensive care unit (NICU) is intended for caring for ill, premature and low-birth-weight infants. There are 2 main types of NICUs: the open-bay (OBA) NICU and single-family room (SFR) NICU. Researches have proved that the SFR NICUs have many advantages as compared with the OBA NICUs ,hence, SFR NICUs are predominant worldwide since 1994. The ventilation system has a crucial role in the infection prevention and control (IPC) program, as …

Investigating Nox Vs Co2 Tradeoff In Heavy Duty Emissions Through The Years Under The Scope Of Carb’S 3-Bin Moving Average Window Method, Ghadi Sadek

Graduate Theses, Dissertations, and Problem Reports (ETD)

With the rise in urban pollution level over the last few years, regulatory agencies around the world have taken multiple steps to ensure engine exhaust pollutant are well monitored and properly regulated. Yet there exists a significant difference in emissions rates in various operating conditions between US and European products which currently uses a Moving average window (MAW) approach for their in-use compliance testing and certification program. Using WVU’s vehicle data collected using PEMS devices, this study aims at investigating the NOx versus CO2 tradeoff found in heavy duty diesel engines equipped with different aftertreatment technologies, under the scope of …

Advance Metallic Reinforcement Of Vat Photo Polymerized Parts, Scott Zinn

UNF Graduate Theses and Dissertations

The metallization or metallic reinforcement of polymer parts has been widely used in industry for several decades. Polymer parts are classically metalized for aesthetics, chemical and thermal resistance, electrical conductivity, and mechanical strength. Metallization has been shown to increase strength of polymer parts when compared to the strength of the bulk material without metallization. Additive manufacturing (AM) techniques that have emerged in the last few decades produce parts with different surface features and chemistry than the typical polymer part produced through injection molding. AM parts are typically weaker than traditionally manufactured parts from the same material due to intrinsic details …

Impact Dynamics Of Surfactant-Laden Droplets On Non-Wettable Coatings, Amir Esmaeili

Theses and Dissertations

Owing to their excellent water repellency, non-wettable (superhydrophobic) coatings have gained tremendous attention in the past couple of decades. Alkyl ketene dimer (AKD), an inexpensive polymer frequently used in paper industry as a sizing agent, has shown potentials to become superhydrophobic. The formation of a porous structure after curing the solidified AKD for an extra-long time (4–6 days) results in superhydrophobicity, i.e., a static contact angle with water of >150° and a roll-off angle of <10°. In this work, a facile and low-cost method was used to turn the surface of AKD superhydrophobic in a very short period of time by briefly treating the coatings, obtained from isothermally heated molten AKD at 40 °C for 3 min, with ethanol. The resulting superhydrophobicity is due to the formation of porous, entangled irregular micro/nano textures that create air cushions on the surface leading to droplet state transition from Wenzel to Cassie. As a proof of concept, the same material was applied to the co-sputtered nickel-tungsten thin films, commonly used in micro/nano-electro-mechanical systems, to improve their hydrophobicity. According to the results, at least 20% increase was observed in the dynamic contact angles of the treated substrates.

In addition, this work presents a detailed high-speed imaging analysis of the influence of the molecular weight, concentration and ionic nature of surfactants on droplet …

Prospects For Solving The Problem Of Rational Use Of Water Resources Using The Tiiame-1 Sprinkling Machine, M.Kh. Khamidov, A.R. Muratov

Irrigation and Melioration

The information published by the International Commission on Irrigation and Drainage, and the intermediate results of many years of research carried out by scientists from TIIAME on the development, research and implementation of water-saving technologies in agriculture are presented. The acute shortage of water resources in Central Asia, the problems of increasing the efficiency of the use of water-saving technologies around the world have led to the careful use of available water resources in the region, including the prospects and advantages of using irrigation of crops by sprinkling, as well as the design and technical parameters of the sprinkler developed …

Inadequacy Of Current Water Use Planning At The Level Of Water Users And Wuas, A.A. Alimdjanov, A.Kh. Karimov, B.R. Nasibov

Irrigation and Melioration

This paper studies the main issues of water use planning at the level of water consumers and water user associations (WUA). The study carried out in Bulakbashi district of Andijan province of Uzbekistan, where the main source of irrigation water is the Southern Fergana Main Canal. The study followed two-stage procedure. During the first stage we compiled water use plans for the WUA and water consumers based on the applied methodology of water use planning. Then, at the second stage, we analyzed the results of the actual implementation of the farm water consumption plans and WUA water use plan, and …

Technology And Technical Device Used In The Efficient Use Of Water Resources In Irrigated Agriculture, А.U. Аtajanov

Irrigation and Melioration

The economical use of water resources, the improvement and development of new technology and technical means for its implementation, ensuring the saving of irrigation water is one of the most important issues of today. This article is devoted to the issues of improving the technology of irrigation of furrows and the creation of technical means,also recommended technology and using from created technical device in selected per experiment fields and analyzing their results.

Empirical Assessment Of Climate Change Impacts On Agriculture In Samarkand Region, Sh.B. Babakholov

Irrigation and Melioration

Agricultural production is highly sensitive to climate factors like other endogenous factors, and the expected climate change projections may have a negative impact on the efficiency and income of agricultural producers. Therefore, this study aims to analyze the impact of changes in climatic factors (average air temperature and precipitation) on the technical efficiency of cotton growing farmers as its determinants in Samarkand region. Empirical analyzes were performed on the cases of 1141 cotton-growing farms using panel-based Time-Invariant Inefficiency model. According to the results of the analysis, cotton farms in the region have an average technical efficiency of 76%, which in …

Car Wash Complex – Object Of Harmful Impact On Water Resources, M. Radkevich, K. Shipilova, M. Abdukodirova, O. Pochugevski

Irrigation and Melioration

Deals with the problem of the impact of car wash complexes in the city of Tashkent on water resources. The analysis of the technological process of washing and a sociological survey of car owners and employees of car washes revealed the average amount of water used per car wash per year, as well as the amount of harmful substances entering the sewer network of the city of Tashkent. Calculations have shown that the annual water consumption only for passenger cars in Tashkent is about 4.34 million m³, and the wastewater is not properly treated. From one car wash …

Agrochemical Indicators Of New Irrigated Graph-Meadow Soils Formed On The Iii Underfladder Terrace Of Syrdarya, J.M. Kuziev

Irrigation and Melioration

Presents material on the geographical location, geomorphological and geological structure, as well as the agrochemical state of irrigated serozem-meadow soils, common in the Mirzaabad district of the Syrdarya region. According to the data obtained on the chemical analysis of soils, the studied soils are medium- and heavily loamy in texture, where particles of coarse sand predominate (0.05-0.01%). In the arable horizon of these soils, the humus content is 1.088-1.214%, total nitrogen 0.079-0.089%, total phosphorus 0.109-0.124%, and total potassium within 1.15-1.24%, and on the basis of these data, a regularity of the underlying horizon of these soils. The degree of provision …

Water Efficient Technology Of Drip Irrigation In Intensive Gardens, F.U. Juraev, G.H. Karimov

Irrigation and Melioration

The studies were carried out in 2017-2019 at the Zodabek farm on a 6 hectare garden plot with seedlings of half-tall apple trees “Golden Delicious”. Experimental research work was carried out at a groundwater level in the experimental area of 1.5-2.0 m, mineralization 1.0-1.2 g/l in alluvial, mechanical, medium sandy soils with the following irrigation options. The first option is irrigation, at the start of the second - drip irrigation; third, the use of specially designed soil pegs. The following results were obtained: in the control option, the average irrigation rate for three years was 1125.7 m3/ha, with drip irrigation …

Forecasting The Dynamics Of Cotton Yield In The Ferghana Region, V. Vakhobov, А.А. Faiziev

Irrigation and Melioration

Observations of a certain phenomenon, the nature of which changes over time, give rise to an ordered sequence, which is called a time series. In the article, using the method of statistical time series analysis, statistical pattern of time series Y₁ – average yield of cotton in Fergana region of the Republic of Uzbekistan(on materials of CSB of the Republic of Uzbekistan for 1991-2018 years). Point and interval estimates for the average cotton yield were constructed with a 95% guarantee, explicit types of trends were determined, and the yield in the region was predicted for subsequent years. Using statistical …

Hydraulic Elevator For Purification Of Water Supply Facilities Of The Reservoir, R.R. Ergashev, F. Atrikbekova, H. Khusanboeva, B.T. Kholbutaev, N.A. Babazhanov

Irrigation and Melioration

The purpose of the research is to increase the efficiency of pumping stations operation by improving the methods of uniform flow spreading in the front chamber and inlet of the pumping station and developing constructive measures to improve the hydraulic conditions for supplying the flow to the pumps. The improvement of the method of hydraulic calculation of the flow in the front chamber and the water intake chamber is given on the example of the head pumping station of the Jizzakh cascade. In the process of research, standard methods of full-scale and bench tests of pumps, methods of mathematical and …

Energy-Saving Structure Justification Powerful Tractor And Modern Agricultural Machine, A.K. Igamberdiyev, N.A. Khalikova, N.B. Razikov, O.E. Usarov

Irrigation and Melioration

Discusses the fact that machine-tractor units (MTA) from high-power tractors are often not fully used due to errors in the design and operation of units, their ability to work under certain operating conditions with maximum efficiency and minimum fuel consumption, a method of completing a machine-tractor unit from a high-power technical means is proposed, which ensures the required quality of the technological operation, maximum efficiency and minimum fuel consumption, which must be performed under certain operating conditions. To study the power balance of energy-saving units, consisting of powerful tractors and modern agricultural machinery, an analysis was carried out of a …

Traction Control Of The Friction Drive Of The Vertical Spindle, M. Shoumarova, T. Abdillaev, Sh.A. Yusupov, Ch.A. Shermatova

Irrigation and Melioration

The main indicator in assessing the quality of the work of cotton pickers is its completeness of picking cotton, among the factors that predetermine the completeness of picking a special place is occupied by the direction and magnitude of the absolute speed of the spindle tooth. Among the factors affecting the absolute speed of the tooth, the main place is occupied by the angular speed of rotation of the spindle around its own axis, which depends on the quality of functioning of the friction drive of the spindle. This drive does not always provide its required traction capacity, since due …

Research The Chopper Apparatus Of Equipment For Chopping Pressed Rough Fodders, Sh.H. Gapparov, N.A. Ashurov

Irrigation and Melioration

Livestock is one of the most important agricultural sectors in Uzbekistan and it is based on family livestock farms. On family farms, livestock animals are fed with pressed roughage, including corn stalks, alfalfa hay, barbed straw and wheat straw, mixed with concentrated feed. However, due to the lack of small choppers suitable for small farms, the compressed feed is fed to animals without chopping, as a result of which about 25-30 percent of them go to waste and there are large losses. Taking this into account, a small device was developed for chopping pressed roughage and mixing it with concentrated …

Theoretical Research On Determining The Length Of The Shovels Of A Wheel Of Centrifugal Fans, V.A. Arkhipov, D. Dzhuraev, I.Zh. Toirov, A.E. Urishev

Irrigation and Melioration

Presents the results of theoretical research by scientists, carried out scientific work to determine the length of the shovel of a centrifugal fan wheel. A technological scheme for installing a shovel on a fan wheel disk has been developed Analyzes of these works are carried out, which show that the length of the wheel shovel has a significant dependence on the parameters of the wheel (R, R₁), the angle of installation α and the radius of the arc R₃ of the shovel. An analytical dependence is derived for determining the length of the shovel of a …

Spectral Absorption Coefficient Of Additive Manufacturing Materials, Nicholas J. Wallace, Matthew R. Jones, Nathan B. Crane

Faculty Publications

Active thermography techniques are of interest for quality assurance of additive manufacturing processes. However, accurate measurements of thermophysical properties of materials are required to successfully implement active thermography. In particular, the spectral absorption coefficient of materials commonly used in additive manufacturing must be known to accurately predict the spatial distribution of thermal energy generated from absorption of power emitted by a laser or pulsed flash lamp. Accurate measurements of these optical properties are also needed to develop greater understanding of additive manufacturing processes that rely on radiative heat transfer to fuse powders. This paper presents spectral absorption coefficient measurements and …

Microparticle Propulsion For In Vivo Navigation, Louis Rogowski

Mechanical Engineering Research Theses and Dissertations

Microscale propulsion impacts a diverse array of fields, with simplistic microrobots allowing for novel innovations in microscale surgery and drug delivery. Propulsion at the microscale is constrained by physics, with time-reversal and geometric symmetries limiting available propulsion mechanisms. However, certain fluid environments and surface coatings allow for the propulsion of microparticles through externally applied magnetic fields. Presented here is a detailed analysis of microparticles propelling using spontaneous symmetry breaking, flagella surface coatings, and multi-modal actuation mechanisms. Spontaneous symmetry breaking in nonlinearly viscoelastic fluids is presented for the first time in literature, with two equal and opposite propulsion states existing along …

A Numerical And Experimental Study Of Lid Driven Square Cavity Flow For Laminar And Turbulent Cases, Abdullah Bin Naeem

LSU New Orleans Theses and Dissertations

Experimental and numerical studies are performed on steady and unsteady lid-driven cavity flow for laminar flow regime. In the experiments, a PIV and an LDA were employed to measure the global and local velocities, respectively inside a cavity of AR 1.0. The velocity vector plots and streamline plots which represent unsteady circulation patterns are obtained using the PIV. The steady local velocities measured with LDA are then used to calibrate the PIV measurements. The numerical study is performed using a commercial CFD solver. For turbulent flow simulation RANS equations with K-Epsilon closure model were used. From the PIV calibration study, …

Performance Improvements For Next Generation Falling Particle Receiver Systems, Nathan R. Schroeder

Mechanical Engineering ETDs

Falling particle receiver (FPR) systems are a rapidly developing technology for concentrating solar power applications. Solid particles are used as both the heat transfer fluid and thermal energy storage media. Through the direct solar irradiation of the solid particles, flux and temperature limitations of tube-bundle receives can be overcome leading to higher operating temperatures and energy conversion efficiencies. Particle residence time, curtain opacity, and curtain stability affect the performance of FPR designs. As the particles fall through the receiver the curtain accelerates, increasing its transmissivity thus decreasing the amount of energy absorbed. Multistage release trough structures catch and release the …

Understanding Of Aerosol Transmission Of Covid 19 In Indoor Environments, Adama Barro, Cathal O'Toole, Jacob S. Lopez, Matthew Quinones, Sherene Moore

Publications and Research

Our reason for discussing severe acute respiratory syndrome corona virus 2 (SARS-CoV-2) or 2019 novel corona virus (Covid-19), is to understand its aerosol transmission characteristics in indoor spaces and to mitigate further spread of this disease by designing a new HVAC system. The problem that we are tackling is the spread of covid-19 droplets through aerosol transmission by looking at potential engineering solutions to the existing HVAC systems. The purpose is to eradicate the spread of the COVID-19 by testing indoor spaces in an effort to understand the effectiveness of ventilation controls. We believe that scientists and engineers have not …

Direct Solar Absorption Nanoparticle Doped Membranes For A Hybrid Membrane Distillation And Photovoltaic Cell, Alejandro Espejo Sanchez

Boise State University Theses and Dissertations

The growing demand for clean water supplies is driving the need for an innovative approach of water desalination. Developing a method for treating water with high salinities is possible with membrane distillation (MD). Additionally, MD is very attractive for pairing with solar energy due to the low temperature requirements. The integration of a membrane distillation system with a photovoltaic (PV) system will result in the co-production of electricity and clean water, thereby improving the economics of MD. Such a hybrid system will directly absorb thermal energy in the membrane for desalination while taking advantage of the spectrally selective nature of …

A.C. Moyer Eye-Cap Manufacturing, Thais Bertolus, Alexa Steidl, Hana Welsh, Jarod Kinney, Maya Willis

Mechanical Engineering

A.C. Moyer company has been making eye caps as a family business since 1947. Eye caps are a product used during the embalming process. Currently the machines being used to produce the eye caps are outdated and unsafe. We are a team of 5 mechanical engineering students tasked with either designing new machines or updating the existing machines to make the manufacturing process more efficient, automated, and safer. This document describes the design process, provides background, relevant research, establishes project objectives, and defines plans for project implementation.

Improvement Of Labyrinth Seal Leakage Rates Using Additive Manufacturing, Austin L. Gasbarra

Master's Theses

The growing popularity of additive manufacturing in commercial applications has al- lowed for new ideas and new ways of thinking when designing components. Further optimization at the component level is possible, though powder metallurgy is in its infancy. This study explores the possibility of using additive manufacturing to develop better labyrinth seals in turbomachinery. Labyrinth seals have a torturous fluid path with high losses, thus limiting the amount of fluid leakage. These types of seals can be non-rotating, allowing them to better take advantage of the additive manufacturing process due to the absence of rotating stresses. Labyrinth seal performance is …

Sustainable Drug Release From Polycaprolactone Coated Chitin‑Lignin Gel Fibrous Scaffolds, Turdimuhammad Abdullah, Kalamegam Gauthaman, Azadeh Mostafavi, Ahmed Alshahrie, Numan Salah, Pierfrancesco Morganti, Angelo Chianese, Ali Tamayol, Adnan Memic

Department of Mechanical and Materials Engineering: Faculty Publications

Non-healing wounds have placed an enormous stress on both patients and healthcare systems worldwide. Severe complications induced by these wounds can lead to limb amputation or even death and urgently require more effective treatments. Electrospun scaffolds have great potential for improving wound healing treatments by providing controlled drug delivery. Previously, we developed fibrous scaffolds from complex carbohydrate polymers [i.e. chitin-lignin (CL) gels]. However, their application was limited by solubility and undesirable burst drug release. Here, a coaxial electrospinning is applied to encapsulate the CL gels with polycaprolactone (PCL). Presence of a PCL shell layer thus provides longer shelf-life for the …