Other Mechanical Engineering Commons^™

System-Level Assessment Of Non-Ideal Phase Change Material Behavior In Low Earth Orbit Spacecraft Thermal Control Models, Nathan S. Bruursema

Dissertations, Master's Theses and Master's Reports

Phase change materials (PCMs) are of interest in spacecraft thermal control because their latent heat capacity can provide passive thermal buffering during transient or cyclic heat loads. PCM behavior is often treated using idealized assumptions such as repeatable phase transition temperatures, consistent thermal accessibility across cycles, and full latent recovery. However, practical PCM behavior may be affected by non-ideal phenomena such as supercooling, interfacial resistance, and degradation of internal transport accessibility. This thesis examines the system-level relevance of these effects for low Earth orbit (LEO) spacecraft thermal control and identifies the operating conditions under which non-ideal PCM behavior becomes design-relevant. …

Development And Calibration Of A 2-D Diesel Oxidation Catalyst Filter (Docf) Model With Spatially Varying Washcoats Using Spacims And Engine Loading Data, Thomas K. Price

Dissertations, Master's Theses and Master's Reports

Diesel engine exhaust contains regulated species, including carbon monoxide, hydrocarbons, nitrogen oxides, and particulate matter (PM). Meeting increasingly stringent emission standards typically requires multiple aftertreatment components, motivating the development of multifunctional devices that reduce system size, cost, and catalyst usage. Computational models are essential for guiding this design process; however, existing models primarily focus on single-function devices and rarely capture the behavior of multifunctional systems with multiple catalyst washcoats. This work presents a physics-based model of a wall-flow diesel oxidation catalyst filter (DOCF), a multifunctional device that integrates the roles of a diesel oxidation catalyst and a diesel particulate filter …

Application Of Reactive Power Theory To Wave Energy Converters Under Multi-Frequency Excitation: Analysis And Experimentation, Mckenna R. Collins

Dissertations, Master's Theses and Master's Reports

There is abundant energy surging in the oceans across the globe. However, there have been technological challenges in extracting that energy for use. Wave energy converter (WEC) technology is being developed to find innovative ways to convert wave kinetic energy into electricity, but there are still efficiency obstacles that inhibit large-scale use. Focusing on heave-point absorber control theory, this thesis continues the work to improve the efficiency of WECs. This is done by leveraging a superposition of linear mass-spring-damper models to analyze a WEC under multi-frequency excitation and applying proportional-derivative gains to each linear model. However, to analyze this system, …

Transient Thermal Finite Element Simulation For Process Modeling In Wire Arc Additive Manufacturing, Satya Sai Kumar Pilli

Dissertations, Master's Theses and Master's Reports

This thesis presents the development of a transient thermal framework for Wire Arc Additive Manufacturing (WAAM) created using ANSYS Workbench. This study aims to understand the inherent properties and thermal behavior of WAAM by using the Finite Element (FE) simulation technique to reduce the need for experiments. Specifically, the transient thermal WAAM simulation framework uses the heat source Goldak model to understand the thermal behavior for a given voltage, initial temperature, and travel speed during the process to predict process temperature. The outcomes of this thesis aim to significantly decrease material waste and repetitive experiments and accelerate production process design …

Measuring Occupant Controlled Ventilation And Cooking Frequency To Aid In Modeling Energy Performance Of Northern Michigan Homes, Jacob J. Chizek

Dissertations, Master's Theses and Master's Reports

This research investigates the real-world interplay between energy efficiency and indoor air quality. We explore how home ventilation strategies, heating systems, and weatherization levels in rural homes interact. As part of a larger study on air quality, 17 homes participated in the study. Specifically, this research shows the results and methods for monitoring cooking frequency, kitchen range hood use, and bathroom fan use over two, month-long study periods to build accurate energy and contaminant transport models of homes that were studied. Energy audits to document home characteristics were conducted, including blower door testing and detailed qualitative data regarding the homes’ …

Linking Molecular Structure Evolution To Mechanical Degradation During Environmental Aging In Conventional And Recyclable Epoxy Systems, Ben T. Jewell

Dissertations, Master's Theses and Master's Reports

The long-term performance of polymeric materials in extreme environments is governed by complex chemical and physical aging processes that alter their molecular structure and mechanical integrity. Conventional thermoset epoxies, while widely used in structural applications, are particularly susceptible to oxidative degradation at elevated temperatures, leading to embrittlement and loss of structural integrity. In the first part of this work, diffusion-limited oxidation (DLO) in a bulk structural epoxy was systematically investigated to establish the link between heterogeneous microstructural evolution and macroscopic mechanical degradation. High-temperature oxidation experiments were conducted in a controlled environmental chamber, and the resulting chemical, thermal, and mechanical changes …

A Physical Test Artifact For Evaluating Edge Cases Of Individual And Fused Automated Driving Perception Sensors, Colin Schaefer

Dissertations, Master's Theses and Master's Reports

With the advent of technologies to support autonomous vehicles (AVs), the number of different AV models from a variety of companies and organizations has proliferated. With this increase in options comes the need to physically evaluate their perception systems. However, there is a lack of standard methods to physically evaluate these perception systems. A set of test artifacts can be used to compare the performances of perception systems, but the artifacts must be usable with different types of perception sensors and various sensor fusion systems. This thesis presents the development of an artifact that injects edge case scenarios into the …

Modeling Pulsatile Flows Using Truly Incompressible Finite Volume Lattice Boltzmann Model, Akshay S. Dongre

Dissertations, Master's Theses and Master's Reports

The present study addresses the compressibility error inherent in the standard Lattice Boltzmann Method (LBM) and LBM’s restriction to uniform Cartesian meshes. To mitigate the compressibility error, an incompressible LBM (iLBM) model has been incorporated into the finite volume framework using a cell-centered finite volume approach, leveraging the simplicity of the LBM algorithm for irregularly shaped flow domains with unstructured meshes. Monotonic Upstream-centered Scheme for Conservation Laws (MUSCL) and linear reconstruction (LR) schemes have been used to compute convective fluxes across the cell interfaces with boundary conditions implemented using the second-order accurate Non-Equilibrium Extrapolation (NEE) method.

The finite volume iLBM …

Data To Physics: Bridging Modeling Frameworks For Metastructures, Hrishikesh Suhas Gosavi

Dissertations, Master's Theses and Master's Reports

The effective attenuation of wave propagation in specific frequency ranges, known as bandgaps, makes metastructures valuable in various engineering applications. Traditionally, bandgap estimation has relied on physics-based models, which present challenges for complex metastructures where accurate material properties and geometric complexities make precise modeling difficult. This work introduces data-driven techniques for bandgap estimation, leveraging the dynamic behavior, particularly the Frequency Response Functions (FRFs) of unit cells, to calculate dispersion relations and couple unit cells through dynamic substructuring. This approach addresses the limitations of traditional methods by directly utilizing experimental data to characterize both longitudinal and flexural bandgaps.

To evaluate data-driven …

Comprehensive Review And Development Of A High-Pressure Hydraulic Impedance Tube For Vibroacoustic Attenuator Characterization, Matthew D. Beals

Dissertations, Master's Theses and Master's Reports

This research establishes a versatile test bench for characterizing hydraulic vibroacoustic attenuators. The primary evaluation metric is the transfer matrix, determined experimentally, with an emphasis on key properties such as transmission loss. To ensure accuracy and broad applicability, the methodology is based on industry-standard techniques for determining the transfer matrix. A comprehensive literature review consolidates existing approaches for hydraulic attenuator characterization. The test bench features a hydraulic impedance tube equipped with eight dynamic pressure transducer (DPT) taps strategically positioned before and after the sample interface. This setup accommodates arbitrary samples terminated with standard hydraulic fittings. Using ASTM E2611, the transfer …

Study Of Nanocomposite Materials Using Molecular Dynamics, Prashik Sunil Gaikwad

Dissertations, Master's Theses and Master's Reports

There is an increase in demand for new lightweight structural materials in the aerospace industry for more efficient and affordable human space travel. Polymer matrix composites (PMCs) with reinforcement material as carbon nanotubes (CNTs) have shown exceptional increase in the mechanical properties. Flattened carbon nanotubes (flCNTs) are a primary component of many carbon nanotube (CNT) yarn and sheet materials, which are promising reinforcements for the next generation of ultra-strong composites for aerospace applications. These flCNT/polymer materials are subjected to extreme pressure and temperature during curing process. Therefore there is a need to investigate the evolution of properties during the curing …

On The Gaussian-Core Vortex Lattice Model For The Analysis Of Wind Farm Flow Dynamics, Apurva Baruah

Dissertations, Master's Theses and Master's Reports

Wind power science has seen tremendous development and growth over the last 40 years. Advancements in design, manufacturing, installation, and operation of wind turbines have enabled the commercial deployment of wind power generation systems. These have been due, in a large part, to the expertise in the simulation and modeling of individual wind turbines. The new generation of wind energy systems calls for a need to accurately predict and model the entire wind farm, and not just individual turbines. The commercial deployment of these wind farms depends on model's ability to accurately capture the different physics involved, each at its …

Wireless Power Transfer In Autonomous Mobile Microgrids, Carl Greene

Dissertations, Master's Theses and Master's Reports

The ability to autonomously dock unmanned ground vehicles plays a key role in mobile micro-grids, where efficient power transfer is paramount. The approach utilized in this work allows for near-field wireless power transfer in remote locations with minimal support. Establishing a micro-grid power system connection autonomously using wireless power eliminates the arduous task of designing a complex, multiple degrees of freedom (MDOF) robotic arm. The work presented in this thesis focuses on both the hardware and software within the micro-grid system. This particular near-field wireless system consists of a primary and secondary set of modules, comprised of Litz wire coils, …

An Experimental Study Towards Underwater Propulsion System Using Structure Borne Traveling Waves, Shreyas Suhas Gadekar

Dissertations, Master's Theses and Master's Reports

The method of generating steady-state structure-borne traveling waves underwater in an infinite media creates abundant opportunities in the field of propulsive applications, and they are gaining attention from several researchers. This experimental study provides a framework for harnessing traveling waves in a 1D beam immersed under quiescent water using two force input methods and providing a motion to an object floating on the surface of the water.

In this study, underwater traveling waves are tailored using structural vibrations at five different frequencies in the range of 10Hz to 300Hz. The resulting fluid motion provides a propulsive thrust that moves a …

Permeability, Structural Changes, Flow Regime Transitions In Fuel Cell Catalyst Layers And A Model For Predicting Trapped Saturation For Two-Phase Flow In Porous Media, Karrar Takleef Alofari

Dissertations, Master's Theses and Master's Reports

Proper water management in Proton Exchange Membrane (PEM) fuel cell is important to achieve high performance. Understanding the percolation of the produced water at the cathode catalyst layer (CL) is critical for any robust water management technique. In this study, an ex-situ experimental setup is used to study percolation in the CL at different injection rates and relative humidity (RH) conditions. The results show that increasing the flow rate force the liquid to flow through the bulk of the pores due to the dominant viscous effect. On the other hand, at low injection rates, the capillary becomes dominant and liquid …

Concept Evaluation And Development Of A Novel Approach For Integration Of Turbogeneration, Electrification And Supercharging On Heavy Duty Engines, Satyum Joshi

Dissertations, Master's Theses and Master's Reports

While many technologies such as electrically assisted turbocharging, exhaust energy recovery and mild hybridization have already proven to significantly increase heavy-duty engine efficiency, the key challenge to their widespread adoption has been their cost effectiveness and packaging. This research specifically addresses these challenges through evaluation and development of a novel technology concept termed as the Integrated Turbogeneration, Electrification and Supercharging (ITES) system. The concept integrates a secondary compressor, a turbocompound/expander turbine and an electric motor through a planetary gearset into the engine cranktrain. The approach enables a reduced system cost and space-claim, while maximizing the efficiency benefits of independent technologies. …

Transient Maneuvers And Pressure Analysis On An Automotive Torque Converter, Abigail A. Hempy

Dissertations, Master's Theses and Master's Reports

This work involves an investigation of internal fluid behavior of an automotive torque converter in a front-wheel drive automatic 6-speed transmission. The fluid behavior is identified through 29 pressure transducers instrumented throughout the torus, acquired through IR Telemetrics multiplexed channels, and analyzed with custom MATLAB code. The main vehicle operating conditions studied in this research are back drive scenarios or low motoring torques. Findings showed speed and torque limits for open converter coast down conditions as well as pressure field behavior with negative input torque.

Torrefaction Of Mixed Solid Waste, Zhuo Xu

Dissertations, Master's Theses and Master's Reports

The world is witnessing unprecedented accumulation of solid wastes in the environment and landfills with well-documented ecological, environmental, health, and economic consequences. With population growth and rise in living standards, solid wastes generation will increase, making the issue more pressing. In addition, current practices of solid waste disposal are creating an immediate challenge and a long-term disaster-scale problem. The solid wastes comprises two main groups of materials: (i) fiber wastes (paper, food, wood, trimming, 61% of U.S. municipal solid waste) and (ii)uniquely challenging subset of plastic wastes (13%) that become a threat to global sustainability including dangers to marine and …

Development Of An Eco Approach And Departure Application To Improve Energy Consumption Of A Plug-In Hybrid Vehicle In Charge Depleting Mode, Brandon Narodzonek

Dissertations, Master's Theses and Master's Reports

A recent study at Michigan Technological University as part of the NEXTCAR DOE APRA-E Project was conducted to determine the potential energy savings of a plug-in hybrid electric vehicle (PHEV) equipped with various Connected and Automated Vehicle (CAV) Technologies. One aspect of this study focused on the development of an Eco Approach and Departure (Eco AnD) Application that would further reduce the energy consumed around a signalized intersection.

Many modern intersections are equipped with traffic signals that can broadcast Basic Safety (BSM), MAP, and Signal Phase and Timing (SPaT) message sets that contain intersection ID, location, current phase, and cyclic …

Buckling Load Study On Pop Nut (Rivet) Using Finite Element Analysis, Saurabh Shankar Shegokar

Dissertations, Master's Theses and Master's Reports

This study highlights the material behavior in riveting operation that includes buckling load analysis using ABAQUS. Finite Element Analysis is used to find the buckling load vs. Displacement results and validated with the results obtained in physical testing of rivet (POP Nut). A mesh sensitivity study is performed using ABAQUS to understand the optimum mesh size for this analysis. An axisymmetric model with contact properties is created and simulated to reduce the simulation time using ABAQUS. The results obtained through Finite Element Analysis show a good resemblance with the testing results. Design changes were suggested to achieve better results that …

Influence Of Micro-Nucleate Boiling On Annular Flow Regime Heat Transfer Coefficient Values And Flow Parameters – For High Heat-Flux Flow Boiling Of Water, Soroush Sepahyar

Dissertations, Master's Theses and Master's Reports

Analysis of results from steady and steady-in-the-mean high heat-flux (15 - 70 W/cm², with water as working fluid) shear driven annular flow-boiling experiments presented here - and low heat-flux (0.1- 1 W/cm², with FC-72 as working fluid) experiments presented elsewhere – together lead to a key conclusion. The conclusion is that heat carrying nucleation rates go often undetected by the typically used visualization approaches for flow boiling – as such flows often involve µm- to sub- µm scale bubble diameters in millimeter-scale ducts. These nucleation rates play a significant role in most of the so-called convective …

Experimental Characterization Of Hydraulic System Sound, Ben Kolb

Dissertations, Master's Theses and Master's Reports

The purpose of this research was to establish test methods for characterizing the interaction between the hydraulic fluid and hydraulic hose at clipping points in mobile heavy equipment hydraulic systems. A simple hydraulic circuit test bench was developed and the laboratory axial piston pump was characterized using ISO 10767-1. A direct relationship between the fluidborne noise and structureborne noise present at each hose clip location was observed for a specific operating condition using operating deflection shapes and structureborne noise measurements. This result shows that optimal hose clip placement can be a viable solution to structureborne noise reduction. Additionally, a modal …

Development Of A Fused Deposition 3d Printed Buoy And Method For Quantifying Wave Tank Reflections, Samantha G. Swartzmiller

Dissertations, Master's Theses and Master's Reports

Testing model scale prototypes is integral to the development of wave energy converter (WEC) technology. Model scale WECs are tested in wave tanks where they are subjected to repeatable wave fields. Their presence in water creates radiated waves that eventually reflect off tank walls disrupting the intended wave field. Fabrication of model scale WECs is another developing aspect of tank testing. Often model WECs are built of foam. Additive manufacturing is a promising alternative although the most common method, fused deposition modeling (FDM) 3D printing, does not typically produce waterproof parts. The goals of this work were 1) develop a …

Remotely Controlled Industrial Robotic Arm And Simulation Of Automated Thermal Furnace, Prince Mehandi Ratta

Dissertations, Master's Theses and Master's Reports

The right execution of controllers ensures the correct analysis of information, generating efficient results and better optimizing the system. In this report, two controllers were designed. Firstly, a remotely controlled robotic arm, since there are no such type commercially available controllers. Moreover, robotic platforms are costly, so students and researchers are often unable to learn the concepts of programming industrial robots. This project makes a non-destructive, remotely-controlled robotic arm to better teach students and researchers about programming and control of robotic arms. Secondly, simulation of an automated thermal furnace for ArcelorMittal on SIMULINK, which is used for the annealing process …

Design And Development Of Personal Protective Equipment Products To Reduce The Impacts Of Machete Injuries For Indigenous Ngäbe Subsistence Farmers In Bocas Del Toro, Panama, Micah Koller

Dissertations, Master's Theses and Master's Reports

Design and development of personal protective equipment products for workers using machetes (MPPE) is considered in the specific context of indigenous Ngäbe subsistence farmers in a small, rural community in Bocas del Toro, Panama where the author spent two years as a Peace Corps volunteer from 2017-2019. People in this community regularly suffer significant health and economic impacts due to accidents with machetes, which are essential tools in their farm work and daily lives. The history, criticisms, and recent frameworks related to product design and development in resource-poor markets is examined, and specific details of the problem of machete injuries …

Meniscus Modeling And Emission Studies Of An Ionic Liquid Ferrofluid Electrospray Source Emitting From A Magneto-Electric Instability, Brandon Jackson

Dissertations, Master's Theses and Master's Reports

This dissertation presents three studies on the electrospray of ionic liquid ferrofluid. Ionic liquid ferrofluids are electrically conductive super-paramagnetic fluids which respond strongly in the presence of electric and magnetic fields. When a small reservoir of ionic liquid ferrofluid is positioned within a magnetic field, magnetic stresses will deform the fluid interface into a peak. The addition of a strong electric field will further stress the fluid interface until a threshold stress is reached at which point the surface tension cannot contain the combined stresses and a spray of fluid or ions results at the apex. This process is termed …

System Architecture Optimization Using Hidden Genes Genetic Algorithms With Applications In Space Trajectory Optimization, Shadi Ahmadi Darani

Dissertations, Master's Theses and Master's Reports

In this dissertation, the concept of hidden genes genetic algorithms is developed. In system architecture optimization problems, the topology of the solution is unknown and hence, the number of design variables is variable. Hidden genes genetic algorithms are genetic algorithm based methods that are developed to handle such problems by hiding some genes in the chromosomes. The genes in the hidden genes genetic algorithms evolve through selection, mutation, and crossover operations. To determine if a gene is hidden or not, binary tags are assigned to them. The value of the tags determine the status of the genes. Different mechanisms are …

Kinesthetic Learning Experience Simulation Using An Online Intervention To Improve Hands-On Ability, David Leach

Dissertations, Master's Theses and Master's Reports

Students enrolled in mechanical and manufacturing engineering programs employ differing levels of mechanical aptitude and practical hands-on ability. Many students lack practical experience tinkering with mechanical devices and mechanisms prior to entering their post-secondary years. Student attention spans in traditional classroom environments appear to be decreasing with the ever-increasing addiction to immediate gratification provided by electronic devices, gaming software, and social media platforms. The question is then raised whether or not modern engineering students have the ability to improve mechanical aptitude by simulating a kinesthetic or tactile learning experience through an online tutorial. This project describes the development and testing …

Development Of Bosch Rate Of Injection Measurement Procedure And Results, Tyler Menucci

Dissertations, Master's Theses and Master's Reports

Recent developments in internal combustion engine technology have shown that gasoline compression ignition (GCI) combustion modes provide a viable pathway to meet future emission regulations. Lower octane middle distillate gasoline like fuels have also been formulated for GCI combustion applications and have shown similar benefits of improved fuel conversion efficiency and a reduction in particulate matter and nitrogen oxide emissions. As these gasoline like GCI fuels have not been well studied, characterization of their rate of injection (ROI) will be beneficial to supplement injector spray characterization measurements and the development of computational fluid dynamic simulations. A fuel collection method and …

Computational Studies On Biomechanics Of Concussion And On Efficacy Of Football Helmets, David Labyak

Dissertations, Master's Theses and Master's Reports

Football helmets have been used for many years to prevent head injuries to players. Over the years, the helmet design has evolved from a crude leather head covering to the more recent form fitting helmets that are seen today. The one design feature that has been common in the majority of all helmets is a hard polycarbonate shell with a foam cushion padding. The main goal of the padding layer was to reduce the amount of linear acceleration during an impact event. The one feature that has been overlooked is how stiff the padding is in rotation.

The purpose of …