Other Mechanical Engineering Commons^™

Method Of Transferring Strained Semiconductor Structure, Michael Nastasi

Department of Mechanical and Materials Engineering: Faculty Publications

The transfer of strained semiconductor layers from one substrate to another substrate involves depositing a multilayer structure on a substrate having surface contaminants. An interface that includes the contaminants if formed in between the deposited layer and the substrate. Hydrogen atoms are introduced into the structure and allowed to diffuse to the interface. Afterward, the deposited multilayer structure is bonded to a second substrate and is separated away at the interface, which results in transferring a multilayer structure from one substrate at least one strained semiconductor layer and at least one strain-induced seed layer. The strain-induced seed layer can be …

Enhance Diamond Coating Adhesion By Oriented Interlayer Microcracking, Habio Guo, Xingcheng Xiao, Yue Qi, Zhi-Hui Xu, Xiaodong Li

Faculty Publications

In this paper, we report a microcrack toughening mechanism for enhancing the adhesion of diamondcoating. The oriented microcracks were formed within the TiC interlayer to dissipate strain energy and accommodate deformation via the crack opening-closing mechanism, thus enhancing the coating/substrate interfacial toughness. The delamination of diamondcoating was effectively prevented when the parallel microcracks were confined within the interlayer and arrested at interfaces of coating/interlayer/substrate. Density functional theory calculations revealed that the highly anisotropicfracture strength of the TiC phase energetically favors crack initiation and propagation along (100) planes only, which are 54.7° away from the interface. These microcracks are constrained inside …

Callaway Golf: Variable Curved Impulse Sealer, Justin Cook, Ben Jones, Sean Reynolds

Mechanical Engineering

No abstract provided.

Pump Sequencing Optimization, John S. Allan, Kyle J. Nekimken, Spencer B. Weills

Mechanical Engineering

The purpose of this document is to demonstrate the design, production, and testing of optimum pump sequencing logic for variable frequency drive (VFD) pumps in commercial heating ventilating and air conditioning (HVAC) systems. The product will be developed by Pump Efficiency Solutions (PES), which is a group of Cal Poly students working on their senior project. The product is being developed for Trane, an industry leader in large scale HVAC systems. MATLAB™, Microsoft Excel, Pump System Improvement Modeling Tool™ (PSIM), and fluid mechanics hand calculations were used during software development. Next, we converted the program into Trane’s graphical programming language …

Supermileage Team - Urban Concept Competition Vehicle Chassis Design Report, Andrew Allport, Kevin Braico, Kevin Charles, George Kyi, William Lai

Mechanical Engineering

This research and design project was proposed by the Cal Poly Supermileage team. They have requested for our team to design an Urban Concept car, a new category of vehicles to compete for fuel efficiency in the Shell Eco-marathon in 2010. The primary focus of our team is in the design and construction of a chassis the Supermileage team can use for the 2010 competition in Fontana, CA. This design must meet dimensional and functional requirements set by Shell while being designed to maximize efficiency in the competition.

There were various chassis concepts under consideration that would possibly work for …

Broccoli Floret Cutter: Gold Coast Packaging, Inc., Sean Stamm, Walter Salguero, Felipe Gomez Jr, Ruben Duenas

Mechanical Engineering

No abstract provided.

Imprinting Polymerfilm On Patterned Substrate, Li Tan, Yen-Peng Kong, Stella W. Pang, Albert F. Yee

Department of Mechanical and Materials Engineering: Faculty Publications

A method of applying a pattern on a topography includes first applying a polymer film to an elastormer member, such as PDMS, to form a pad. The pad is then applied to a substrate having a varying topography under pressure. The polymer film is transferred to the substrate due to the plastic deformation of the polymer film under pressure compared to the elastic deformation of the PDMS member pulls away from the polymer layer, thereby depositing the polymer layer, thereby depositing the polymer layer upon the substrate.

Modeling And Simulation Of Interactions Between Blast Waves And Structures For Blast Wave Mitigation, Wen Peng

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Explosions occur in military conflicts as well as in various industrial applications. Air blast waves generated by large explosions move outward with high velocity, pressure and temperature. The blast waves not only incapacitate military and civilian personnel, but also damages buildings, vehicles, and other properties. Hence, there has been extensive research on how to mitigate blast wave effects. Understanding the interactions between blast waves and structures is a very important step in the development of devices for blast wave mitigation. The objective of this dissertation is to explore the complicated physical problem of blast waves impacting structures. The structures comprise …

The Next Generation Router System Cooling Design, Garrett A. Glover

Master's Theses

Advancements in the networking and routing industry have created higher power electronic systems which dissipate large amounts of heat while cooling technology for these electronic systems has remained relatively unchanged. This report illustrates the development and testing of a hybrid liquid-air cooling system prototype implemented on Cisco’s 7609s router. Water was the working fluid through cold plates removing heat from line card components. The water was cooled by a compact liquid-air heat exchanger and circulated by two pumps. The testing results show that junction temperatures were maintained well below the 105°C limit for ambient conditions around 30°C at sea level. …

Hole-Type Aerospike Compound Nozzle Thrust Vectoring, Stanley Ikuo Beebe

Master's Theses

Compound aerospike nozzles were designed and tested as part of an ongoing

experimental study to determine the feasibility of thrust vectoring an aerospike

nozzle with the addition of a secondary port. Earlier phases of the study have

indicated that a compound aerospike nozzle could provide sufficient thrust

vectoring. The addition of a hole-type secondary port was found to provide

effective thrust vectoring.

Experiments were carried out to determine the effects of secondary port size,

secondary port inlet geometry and compound aerospike nozzle chamber

pressure. Results show good predictability, axisymmetric flow, and emphasize

the importance of a radius on secondary port …

Strain Energy And Lateral Friction Force Distributions Of Carbon Nanotubes Manipulated Into Shapes By Atomic Force Microscopy, Mark C. Strus, Roya R. Lahiji, Pablo Ares, Vincente Lopez, Arvind Raman, Ron R. Reifenberger

Other Nanotechnology Publications

The interplay between local mechanical strain energy and lateral frictional forces determines the shape of carbon nanotubes on substrates. In turn, because of its nanometer-size diameter, the shape of a carbon nanotube strongly influences its local electronic, chemical, and mechanical properties. Few, if any, methods exist for resolving the strain energy and static frictional forces along the length of a deformed nanotube supported on a substrate. We present a method using nonlinear elastic rod theory in which we compute the flexural strain energy and static frictional forces along the length of single walled carbon nanotubes (SWCNTs) manipulated into various shapes …

Flexible Electronics Using Ion Implantation To Adhere Polymer Substrate To Single Crystal Silicon Substrate, Terry L. Alford, Douglas C. Thompson Jr., Hyunchul Kim, Michael A. Nastasi, James W. Mayer, Daniel Adams

Department of Mechanical and Materials Engineering: Faculty Publications

An electronic apparatus uses a single crystalline silicon Substrate disposed adjacent to a flexible substrate. The electronic apparatus may be a flexible flat panel display, or a flexible printed circuit board. The flexible substrate can be made from polymer, plastic, paper, flexible glass, and stainless steel. The flexible substrate is bonded to the single crystalline substrate using an ion implantation process. The ion implantation process involves the use of a noble gas Such as hydrogen, helium, Xenon, and krypton. A plurality of semiconductor devices are formed on the single crystalline silicon Substrate. The semi conductor devices may be thin film …

Design, Construction And Evaluation Of A Multi Layered Solar Distillation Prototype, Arlen A. Flanagan

BioResource and Agricultural Engineering

Water is arguably the most important resource to any individual; especially in areas of deserts and open oceans where drinkable water suppliers are scarce. The prototype Solar Desalination Unit allows normally undrinkable water to be distilled into a potable source with minimal inputs. The unit’s main power source is focused sunlight to thermally heat water inducing evaporation which is then condensed and collected. While solar desalination has been around for many years, lately more complex designs have been investigated in order to increase yields and efficiency. This paper focuses on the design, construction and testing of a Multi-Plate Solar Desalination …

The Magic Atm, Amber Iraeta, Jason Sy, August Brower

Mechanical Engineering

No abstract provided.

Pressure-Driven Transport Of Particles Through A Converging-Diverging Microchannel, Ye Ai, Sang W. Joo, Yingtao Jiang, Xiangchun Xuan, Shizhi Qian

Mechanical Engineering Faculty Research

Pressure-driven transport of particles through a symmetric converging-diverging microchannel is studied by solving a coupled nonlinear system, which is composed of the Navier–Stokes and continuity equations using the arbitrary Lagrangian–Eulerian finite-element technique. The predicted particle translation is in good agreement with existing experimental observations. The effects of pressure gradient, particle size, channel geometry, and a particle’s initial location on the particle transport are investigated. The pressure gradient has no effect on the ratio of the translational velocity of particles through a converging-diverging channel to that in the upstream straight channel. Particles are generally accelerated in the converging region and then …

Optimization And Stress Analysis Of A Single Stage Rotary Compressor Shaft, Arjunkumar Tummuri

Morehead State Theses and Dissertations

A thesis presented to the faculty of the College of Science & Technology at Morehead State University in partial fulfillment of the requirements for the Degree of Master of Science by Arjunkumar Tummuri May 5, 2009.

Design Optimization Of The Rolling Piston Type Rotary Compressor, Pavankumar Kurmagadda

Morehead State Theses and Dissertations

A thesis presented to the faculty of the College of Science & Technology at Morehead State University in partial fulfillment of the requirements for the Degree of Master of Science by Pavankumar Kurmagadda May 5, 2009.

Low Temperature, Organic-Free Synthesis Of Ba3B6O9(Oh)6 Nanorods And Ss-Bab2O4 Nanospindles, Rui Li, Xinyoung Tao, Xiaodong Li

Faculty Publications

Using a low temperature, organic-free hydrothermal technique, single-crystalline barium polyborate Ba₃B₆O₉(OH)₆ (BBOH) nanorods were synthesized. It was found that β-BaB₂O₄(BBO) nanospindles can be achieved by annealing the BBOH nanorods at a relatively low temperature of 810 °C. Transmission electron microscopy (TEM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS) techniques were used to characterize these nanomaterials. The formation mechanisms are discussed in conjunction with the crystallographic characteristics and surface energy of the BBOH nanorods and BBO nanospindles. UV-vis absorption spectra demonstrated that both BBOH nanorods and BBO nanospindles are …

Temperature Influence And Heat Management Requirements Of Microalgae Cultivation In Photobioreactors, Thomas Hagen Mehlitz

Master's Theses

Microalgae are considered one of the most promising feedstocks for biofuel production for the future. The most efficient way to produce vast amounts of algal biomass is the use of closed tubular photobioreactors (PBR). The heat requirement for a given system is a major concern since the best algae growth rates are obtained between 25-30 °C, depending on the specific strain. A procedure to determine temperature influence on algal growth rates was developed for a lab-scale PBR system using the species Chlorella. A maximum growth rate of 1.44 doublings per day at 29 °C (optimal temperature) was determined. In addition, …

Co-Op E3 Cockshutt 30 Restoration, Tractor Museum

Tractor Maintenance, Repair, and Restoration

Larsen Tractor Museum 2009 Restoration Project

Fuzzy Optimal Swarm Of Autonomous Aircrafts For Target Determination And Convergence Control System, Zach D. Richards

Electronic Theses and Dissertations

The thesis project proposes analytical and theoretical algorithms for a networked swarm of autonomous vehicles, such as those used in planet exploration, and to be used in target location determination and convergence, an algorithm of this type could be used in an Autonomous Stratospheric Aircraft (ASA), thus having the possibility of being used for the exploration of a planet as well as many other applications. Upon locating an unknown location of a specified target, the algorithm would then swarm and eventually converge upon the location. There are two similar, but fundamentally different algorithms proposed in this project. These algorithms are …

Nebraska Summary: S695 Agco Rt155a, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1955 John Deere 5055e Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Identification Of Multiple Oscillation States Of Carbon Nanotube Tipped Cantilevers Interacting With Surfaces In Dynamic Atomic Force Microscopy, Mark Strus, Arvind Raman

Birck and NCN Publications

Carbon nanotubes (CNTs) have gained increased interest in dynamic atomic force microscopy (dAFM) as sharp, flexible, conducting, nonreactive tips for high-resolution imaging, oxidation lithography, and electrostatic force microscopy. By means of theory and experiments we lay out a map of several distinct tapping mode AFM oscillation states for CNT tipped AFM cantilevers: namely, noncontact attractive regime oscillation, intermittent contact with CNT slipping or pinning, or permanent contact with the CNT in point or line contact with the surface while the cantilever oscillates with large amplitude. Each state represents fundamentally different origins of CNT-surface interactions, CNT tip-substrate dissipation, and phase contrast …

Computational Model For Predicting Nonlinear Viscoelastic Damage Evolution In Materials Subjected To Dynamic Loading, Flavio V. Souza, Yong-Rak Kim, George A. Gazonas, David H. Allen

Department of Mechanical and Materials Engineering: Faculty Publications

Many inelastic solids accumulate numerous cracks before failure due to impact loading, thus rendering any exact solution of the IBVP untenable. It is therefore useful to construct computational models that can accurately predict the evolution of damage during actual impact/dynamic events in order to develop design tools for assessing performance characteristics. This paper presents a computational model for predicting the evolution of cracking in structures subjected to dynamic loading. Fracture is modeled via a nonlinear viscoelastic cohesive zone model. Two example problems are shown: one for model validation through comparison with a one-dimensional analytical solution for dynamic viscoelastic debonding, and …

Test 1948: John Deere 5093e Ltd. Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1953: Challenger Mt845c Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1931a: Challenger Mt975c, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1949: John Deere 6115d Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1947: John Deere 5083e Ltd. Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …