Other Mechanical Engineering Commons^™

Enhancing Miter Saw Safety: Challenges And Prospects Of Brake Incorporation With An Automatic Blade Retraction System, Derek Cole

University Honors Theses

Miter saws pose significant safety risks with thousands of injuries reported annually. Despite this risk, they are still used every day as they are a necessity for thousands of workers in the United States and globally. This leaves a demand to make these machines safer to mitigate any potential harm. This research addresses the critical need for an automatic safety system for miter saws, aiming to enhance user safety by retracting and stopping the blade upon skin contact. This analysis identified the primary challenge: The large force generated when braking at high speed on a miter saw blade, translates the …

Consumer 3d Printing For Remote Control Aircraft Wings: Development Of Novel Wingbox Structure, Ian Clark

University Honors Theses

Remote control aircraft construction and can be a very expensive and time-consuming hobby. With 3D printer consumer adoption rates skyrocketing, there is a gap between demand for RC aircraft and suitable well-designed models available to creators and hobbyists. By creating and testing two iterations of wingbox geometries, this research aims to help close that gap by producing an easily printable wing structure. While there are improvements that can be made on this work, this research has been effective in generating a novel wingbox structure for FFF 3D printing that has distinct advantages over other designs currently available.

Quantification Of Reynolds Shear Stress Wave-Phase Dependence In Fixed-Bottom Offshore Wind Turbine Via Quadrant Analysis, Cerrina Mouchref

University Honors Theses

As the need for a reliable renewable energy supply is increasing, many have looked to offshore wind because they hold more potential for power production than onshore wind. Interests in expanding offshore wind energy has brought along many challenges when it comes to understanding the complex dynamics experienced offshore, including the relationship between the wind-turbine generated wakes and ocean waves. This experimental study characterizes the relationship between Reynolds shear stress and the phase of surface waves above the air-sea interface in the wind-turbine wake region. The experimental setup combines a wave tank, wind tunnel, and a fixed-bottom wind turbine. Particle …

Optimization Of 3d Printed Mold Performance For Injection Molding Via Hollow Infill Patterns, Alan Fong

University Honors Theses

The applicability of hollow infill patterns has been explored for its applications in making 3D printed polymer-based injection molds in the additive manufacturing industry. Hollow infill patterns offer a significant reduction in material costs as well as the opportunity for reducing the cooling times via pumping a coolant fluid through the hollow cavity in a similar fashion to traditional conformal cooling channels. A 3D Jacks Support Hollow mold model was determined to be the best performing design. FEA analysis was conducted to determine the maximum reduction in internal volume (percentage of material saved) that could be achieved without exceeding the …

Extending The Functional Subnetwork Approach To A Generalized Linear Integrate-And-Fire Neuron Model, Nicholas Szczecinski, Roger Quinn, Alexander J. Hunt

Mechanical and Materials Engineering Faculty Publications and Presentations

Engineering neural networks to perform specific tasks often represents a monumental challenge in determining network architecture and parameter values. In this work, we extend our previously-developed method for tuning networks of non-spiking neurons, the “Functional subnetwork approach” (FSA), to the tuning of networks composed of spiking neurons. This extension enables the direct assembly and tuning of networks of spiking neurons and synapses based on the network’s intended function, without the use of global optimization ormachine learning. To extend the FSA, we show that the dynamics of a generalized linear integrate and fire (GLIF) neuronmodel have fundamental similarities to those of …

Modeling Airflows And Voc Source Strengths For An Occupied School, Brett Stinson

University Honors Theses

Volatile organic compounds (VOCs) are a group of air pollutants that can adversely impact human health, engage in chemistry indoors, and meaningfully degrade indoor and outdoor urban air quality. While extensive research with regard to VOC emission rates from indoor sources has been conducted, it was not until recently that this work began to focus on characterizing emissions from humans and human activity in depth. As buildings are constructed to be increasingly airtight, and the materials utilized are chosen to reduce VOC emissions, it follows that human contributions are poised to become increasingly important indoor sources of VOCs. Utilizing data …

A Study Of Microwave Curing Of Underfill Using Open And Closed Microwave Ovens, Aditya Thakare

Dissertations and Theses

As the demand for microprocessors is increasing with more and more consumers using integrated circuits in their daily life, the demand on the industry is increasing to ramp up production.

In order to speed up the manufacturing processes, new and novel approaches are trying to change certain aspects of it. Microwaves have been tried as an alternative to conventional ovens in the curing of the polymers used as underfills and encapsulants in integrated circuits packages. Microwaves however being electromagnetic waves have non uniform energy distribution in different settings, causing burning or incomplete cure of polymers.

In this study, we compare …

Development Of Dynamic Thermal Performance Metrics For Eco-Roof Systems, Seth Sinclair Moody

Dissertations and Theses

In order to obtain credit for an eco-roof in building energy load calculations the steady state and time-varying thermal properties (thermal mass with evapotranspiration) must be fully understood. The following study presents results of experimentation and modeling in an effort to develop dynamic thermal mass performance metrics for eco-roof systems. The work is focused on understanding the thermal parameters (foliage & soil) of an eco-roof, further validation of the EnergyPlus Green Roof Module and development of a standardized metric for assessing the time-varying thermal benefits of eco-roof systems that can be applied across building types and climate zones. Eco-roof foliage, …