Other Mechanical Engineering Commons^™

Prediction Of Satellite Temperature During An Orbit Of A Cubesat, Michael Reynolds

Honors Theses

This thesis develops a thermal-simulation strategy for predicting CubeSat component temperatures, applied to Jag-Sat-1, a CubeSat developed at the University of South Alabama and deployed from the International Space Station in 2022. The orbit was reconstructed from two-line element (TLE) data using simplified general perturbations (SGP4) propagation, and spacecraft attitude was recovered from onboard gyroscope measurements. Sunlight, penumbra, and umbra intervals were computed geometrically, and the external radiative environment — direct solar, Earth infrared, and albedo heat fluxes — was modeled using orientation-dependent view factors. These time-varying fluxes drove a transient finite-element thermal simulation of the full satellite geometry in …

System-Level Assessment Of Non-Ideal Phase Change Material Behavior In Low Earth Orbit Spacecraft Thermal Control Models, Nathan S. Bruursema

Dissertations, Master's Theses and Master's Reports

Phase change materials (PCMs) are of interest in spacecraft thermal control because their latent heat capacity can provide passive thermal buffering during transient or cyclic heat loads. PCM behavior is often treated using idealized assumptions such as repeatable phase transition temperatures, consistent thermal accessibility across cycles, and full latent recovery. However, practical PCM behavior may be affected by non-ideal phenomena such as supercooling, interfacial resistance, and degradation of internal transport accessibility. This thesis examines the system-level relevance of these effects for low Earth orbit (LEO) spacecraft thermal control and identifies the operating conditions under which non-ideal PCM behavior becomes design-relevant. …

Advancing Real-World Implementation Of The Well Optimized Linear Finder (Wolf) High-Speed Atmospheric Turbulence Compensation Method, Timothy Evan Coon

Theses and Dissertations

This dissertation advances the real-world implementation of the Well Optimized Linear Finder (WOLF) method for high-speed Atmospheric Turbulence Compensation (ATC). Atmospheric turbulence introduces phase aberrations into optical wavefronts and degrades image quality in terrestrial imaging systems. Traditional phase diversity methods are computationally intensive and poorly suited to real-time operation. The WOLF method addresses these limitations through a novel, point-wise formulation of the optical transfer function (OTF) as a structured autocorrelation of the generalized pupil function (GPF). This formulation enables the estimation of phase aberrations at individual spatial coordinates with distributed computational complexity.

The research begins by developing a MATLAB-based simulation …

An Engineering Solution For Fan Aeroacoustics Measurements Correction In A Non-Anechoic Testing Environment, Saad-Eldin Taha, Mohamed Y.Zakaria, Mohamed Abdelgaied, M.M. Bassuoni Prof. Dr.

Journal of Engineering Research

Abstract- Nowadays, acoustic signatures of daily used applications are to be minimized. The study of noise generated through aerodynamic interaction with moving bodies has passed through different phases since the early 50s, and this leads to the evolvement of many analytical, empirical and computational techniques in order to be able to estimate the emitted noise. Concerning fan blades, until now the researches are still going for a reliable method for noise estimation during the early phases of design which help in the development of blades with a lower aeroacoustic signature, the Brooks, Pope and Marcolini (BPM) model was chosen to …

Ultrafast Laser Surface Structuring For Wettability Control On Copper, Akshay Arvind Nagvenkar

All Theses

Wettability is a crucial surface property influencing various phenomena, including heat transfer, cell adhesion, and corrosion. Engineering devices can achieve superior performance by precisely manipulating surface wettability. As a result, extensive research has focused on developing surfaces that exhibit either extreme water attraction (superhydrophilic) or strong water repellency (superhydrophobic). Tailoring surface wettability paves the way for numerous applications, such as drag reduction in marine vessels, controlled drug delivery, efficient water collection, advanced liquid transport systems, oil-water separation, anti-corrosion coatings, friction reduction, and self-cleaning materials. Ultrafast laser surface structuring is a promising approach for engineering multifunctional surfaces, effectively modifying material properties …

Reconfigurable Python Autopilot Software For Rc Aircraft, Kate Doiron

Honors Theses

No abstract provided.

Effects Of The Gravity Gradient On The Path Of 1i/‘Oumuamua, Hannah R. Richardson

Honors Theses

In October 2017, the asteroid 1I/’Oumuamua first passed into viewing range [1]. The asteroid is notable for being the first interstellar object to enter the solar system. 1I/’Oumuamua was also unusual in its geometry; it is thought to have an aspect ratio of 6:1 and a length of approximately 400 m [2] [3]. The asteroid was observed to experience a non-Keplerian acceleration estimated to be on the order of 1⇥10−6 m s2 . Several theories have been proposed for the cause of this acceleration, all of which are non-gravitational in nature: volatile outgassing, photon pressure, and solar winds [1][4]. However, …

Autonomous Control Of A Hybrid Unmanned Aerial Towed System On A Moving Platform, Zachary M. Miller

Graduate Theses and Dissertations (2019 - present)

With tethered rotor drones being more popular for aerial surveillance, moving platforms for tethered drones are being researched. However, these systems require constant power to the rotor drones for stabilization. With this difficulty in power consumption, a hybrid drone solution is presented. The hybrid drone is similar to an airplane, with quadcopter motors attached for stabilization and thrust when not moving.

The controller for the hybrid drone was tested and verified in simulation. The simulation of the system was built in Fortran and consists of a driver, a tether, and a hybrid drone. The driver was modeled after a generic …

G.W.A.I.H.I.R. Guided Wing Aircraft For Intelligent Hybrid Insertion And Recovery, Abdirahman Ahmed Shirwa, Zach Richards, Derek Harwood, Alex Duncan

Senior Design Project For Engineers

The paper outlines the conceptual and preliminary design of a hybrid vertical takeoff and landing (VTOL) heavy lift unmanned aerial vehicle (UAV) for autonomous cargo transport missions. The primary design objective was to create an aircraft capable of carrying a 15 kg payload over a range of 33 km, achieving a top cruise speed of 45 km/h and maintaining an endurance capacity of at least 90 minutes.

A comprehensive literature review informed key design decision, including airfoil selection, structural material, propulsion system configuration, and control. Key requirements were established early in the design process, such as payload capacity, energy efficiency, …

Enhancing Gas Cyclone Performance With Exit Diffusers, Omar Mohamed Mourad Dwidar, Yasser El-Shaer, Khairy Elsayed, Seyyed Hossein Hosseini, Goodarz Ahmadi

Journal of Engineering Research

This study evaluates seven cyclone designs to enhance pressure drop and collection efficiency (CE), using the conventional cyclone as a baseline. While the conventional design is efficient in particle collection, it experiences significant energy losses due to high values of pressure drops. This study introduces exit diffusers with various configurations—A, B, C, D, E, and F—to improve cyclone performance. Computational Fluid Dynamics (CFD) simulations were used to analyse the pressure drop, tangential velocity, and static pressure at different levels of each cyclone. The findings reveal that cyclone D achieves a 41.1% reduction in pressure drop but at the cost …

Design Strategy For Hybrid Thrust Air Bearings: Comparative Analysis Of Rigid Vs. Foil Bearings Considering Optimum Taper Angle And Orifice Location With Experimental Validation, Ehiremen Ebewele

Mechanical and Aerospace Engineering Dissertations - Archive

Gas foil thrust bearings (GFTBs) are contactless bearings that offer advantages such as lightweight construction and the ability to accommodate misalignments and geometric irregularities. However, their load capacity is lower than rigid or magnetic bearings. The structure and geometry of the foil significantly influence GFTB performance. The taper-flat design is the most used configuration due to its effectiveness and ease of implementation. Key parameters in designing this geometry include taper ratio, taper height, orifice size, and orifice location. These parameters must be optimized alongside manufacturing constraints to produce an effective GFTB. This study presents a design optimization investigation of various …

High-Altitude Balloon-Launched Uncrewed Aircraft System Measurements Of Atmospheric Turbulence And Qualitative Comparison With Infrasound Microphone Response, Anisa Haghighi

Theses and Dissertations--Mechanical and Aerospace Engineering

This study explores the use of a balloon-launched uncrewed aircraft system (UAS) to measure atmospheric turbulence in the troposphere and lower stratosphere using both wind velocity measurements and infrasonic acoustic energy. The UAS, a glider configured for autonomous descent along a predefined trajectory, had on board, in situ sensors to capture thermodynamic and kinematic atmospheric parameters. Additionally, it carried an infrasonic microphone to evaluate its potential for remotely detecting clear-air turbulence by capturing infrasonic waves. The system’s performance was assessed over the course of three test flights conducted in New Mexico, USA, in 2021. The descent enabled high-resolution profiling, with …

Linking Molecular Structure Evolution To Mechanical Degradation During Environmental Aging In Conventional And Recyclable Epoxy Systems, Ben T. Jewell

Dissertations, Master's Theses and Master's Reports

The long-term performance of polymeric materials in extreme environments is governed by complex chemical and physical aging processes that alter their molecular structure and mechanical integrity. Conventional thermoset epoxies, while widely used in structural applications, are particularly susceptible to oxidative degradation at elevated temperatures, leading to embrittlement and loss of structural integrity. In the first part of this work, diffusion-limited oxidation (DLO) in a bulk structural epoxy was systematically investigated to establish the link between heterogeneous microstructural evolution and macroscopic mechanical degradation. High-temperature oxidation experiments were conducted in a controlled environmental chamber, and the resulting chemical, thermal, and mechanical changes …

Bio-Inspired Airfoil Design Based On The Aerodynamic Analysis Of A Bird Feather Microstructure, Jack C. Ihm

College of Graduate Studies: Theses & Dissertations

This study investigates the aerodynamic effects of a bio-inspired airfoil design based on the microstructure of a secondary feather from a female wood duck. The research hypothesized that incorporating barbs and barbules into an airfoil design would modify boundary layer behavior by introducing localized flow disturbances. To test this, a bio-inspired airfoil was developed by integrating the microstructure into a NACA 0012 airfoil and analyzed using computational fluid dynamics (CFD) simulations at angles of attack of 0°, 5°, 10°, and 15°. The results showed that the bio-inspired airfoil influenced boundary layer behavior, producing localized flow disturbances near x/c = 0.7 …

Numerical Study Of Flow Control On An Asymmetric Beveled Trailing Edge, M. M. Mosallem, Zienab A. Ahmed

Journal of Engineering Research

The current research aims to numerically study the effect of inserting a small rod into the wake of an asymmetric beveled trailing edge on the hydrodynamic forces and wake structure. The test model used in this study is a blunt-faced flat plate of thickness H and having an asymmetrical 60° beveled trailing edge. A control rod with diameter d = 0.2 H was inserted into two different locations (Location (1); x/H = 0.18, y/H = 1.0) and (Location (2); x/H = 0.28, y/H = 0.9) behind the trailing edge. Unsteady 2D numerical simulation was performed at Reynolds number, …

Cryogenic Fuel Applications To Sustainable Commercial Aircraft, Jack R. Kisling, Lillian Panning

College of Engineering Summer Undergraduate Research Program

Finding a source of clean and renewable energy is one of the greatest challenges humanity will face in the 21st century. With populations expanding, developing countries increasing their use of resources, and the rapid and alarming effects of climate change, a shift to a sustainable future is an existential prospect.

The goal of our project is to take the first steps toward getting safety procedures and lab space established, so mechanical engineering senior projects can quickly begin to experiment with cryogenic fuels. They will explore the application of cryogenic fuels to commercial aviation.

F56: Rocket Thrust Vector Control, Ethan Douglas Anderson, Yiming Trent Jia, Sahil Sampat

Mechanical Engineering

This Final Design Review (FDR) report compiles relevant information regarding the Rocket Thrust Vector Control senior project as sponsored by Ethan Anderson from Cal Poly Space Systems (CPSS). Documented in this report is our progress from the months following our Critical Design Review (CDR) completion. This consists of a brief overview of the design our thrust vector control (TVC) system and its subassemblies with design changes noted, a thorough walkthrough of our procurement, manufacturing, and assembly process for creating our verification prototype (including software), a breakdown of how we verified each of our specifications through inspection and testing and the …

System Identification For Motion Control Of Unmanned Aerial Vehicles Platform, Raj Ramesh Agarwal

Theses and Dissertations

Comprehensive research on Unmanned Aerial Vehicles (UAV) system identification for motion control parameters is presented in this thesis, with a focus on the necessity of precise control and improved performance. Using Pseudorandom Binary Sequence (PRBS) and Normally Distributed Random Numbers, it presents a unique technique for excitation of UAV dynamic systems. It also shows how effective random signals are in time-domain identification for precise control in a range of flying circumstances. The piece of research includes a thorough analysis and implementation of various approaches and its further improvements, highlighting the benefits and drawbacks of each. These approaches include the free …

Two-Phase Flow Simulations With Plic-Vof Method And Dynamic Mesh Refinement, Vimalan Adaikalanathan

Mechanical and Aerospace Engineering Dissertations - Archive

Two-phase flows are critical in a variety of engineering applications that span multiple length scales. These applications encompass macroscopic phenomena, such as dam breakage and wave-structure interactions, as well as microscopic events, including droplet impacts and boiling, and mixed-scale issues like spray dynamics. Accurate representation of evolving interfaces is essential for numerical simulations of these problems, and the Volume of Fluid (VOF) method combined with the Piecewise Linear Interface Calculation (PLIC) approach is employed to fulfill this requirement. To tackle the computational challenges associated with high-resolution meshes in deforming two-phase flows, Adaptive Mesh Refinement (AMR) is utilized to enhance mesh …

Numerical Simulation And Optimization Of Fin Configurations For Enhanced Heat Sink Performance In Aluminum And Copper Materials, Rimpy Singh

Mechanical and Aerospace Engineering Theses - Archive

The constant evolution of data centers and high-power electronic systems has raised critical challenges in heat dissipation and thermal management. Single-phase immersion cooling, where electronic components are submerged in a thermally conductive but non-electrically conductive liquid (dielectric liquid), offers improved heat dissipation capabilities and emerges as a promising alternative to traditional air-cooling methods, which often fail to meet the thermal demands of densely packed, high-power systems. This study investigates and compares the thermal performance of aluminum and copper heat sinks with fin thicknesses of 0.33 mm and 0.54 mm, respectively, using finite element analysis based on computational fluid dynamics (CFD) …

Comprehensive Review And Development Of A High-Pressure Hydraulic Impedance Tube For Vibroacoustic Attenuator Characterization, Matthew D. Beals

Dissertations, Master's Theses and Master's Reports

This research establishes a versatile test bench for characterizing hydraulic vibroacoustic attenuators. The primary evaluation metric is the transfer matrix, determined experimentally, with an emphasis on key properties such as transmission loss. To ensure accuracy and broad applicability, the methodology is based on industry-standard techniques for determining the transfer matrix. A comprehensive literature review consolidates existing approaches for hydraulic attenuator characterization. The test bench features a hydraulic impedance tube equipped with eight dynamic pressure transducer (DPT) taps strategically positioned before and after the sample interface. This setup accommodates arbitrary samples terminated with standard hydraulic fittings. Using ASTM E2611, the transfer …

An Experimental Investigation Of The New Vibration Viscometer, Jamshidbek Ulugbek Ugli Shamuratov

Technical science and innovation

The characteristics of the new oscillating-plate viscometer have been investigated experimentally. The results obtained are as follows: the resonant frequency of plate oscillation decreases with increasing viscosity; the apparatus constant 𝐾 determined experimentally includes the end and slip effects; the dimensions of the plate should be determined by referring to empirical relations between 𝜌𝜇 and Λ(≡{(𝐸𝑎𝐸)−1}𝑛) for various dimensions of the plate; where 𝜌 is the density, 𝜇 is the viscosity; 𝐸𝑎 the resonant amplitude of plate in the air; E the amplitude of plate in a liquid, and 𝑛 a constant. If the distance between the plate and the …

Consumer 3d Printing For Remote Control Aircraft Wings: Development Of Novel Wingbox Structure, Ian Clark

University Honors Theses

Remote control aircraft construction and can be a very expensive and time-consuming hobby. With 3D printer consumer adoption rates skyrocketing, there is a gap between demand for RC aircraft and suitable well-designed models available to creators and hobbyists. By creating and testing two iterations of wingbox geometries, this research aims to help close that gap by producing an easily printable wing structure. While there are improvements that can be made on this work, this research has been effective in generating a novel wingbox structure for FFF 3D printing that has distinct advantages over other designs currently available.

Cooled Liquid Rocket Thrust Chamber, Benjamin Gibson, Kealan Frederick Harris, Ryan Frank Schackel, Bjorn Thorsen

Mechanical Engineering

Cooling may affect the thrust output of a small-scale rocket. Little research is published about small-scale rocket performance. We hypothesize the thrust produced varies as the amount of cooling varies. To facilitate assessing this hypothesis, we have designed and built a liquid rocket engine rated for at approximately 25 lb_f of thrust. Our objective was to build in parallel with Cal Poly Space Systems, who built a rocket engine with similar specifications except without cooling. Our challenge is to integrate film cooling, so that the effects of cooling may be compared to Cal Poly Space System’s engine which has …

Disc Golf Throwing Robot, Nevada S. Schultz, Sydney M. Lewis, Erick Edmundo Daza, Rachel Alysse Greenberg, Peter M. Kean

Mechanical Engineering

Disc golf companies need better methods to test disc flight. The scope of this project is to create a disc throwing robot that can throw a disc golf driver 450-500 feet, with control over the speed, spin, and release angle. Research shows that multiple disc-throwing products exist; however, none meet the full requirements of this project. The Cal Poly senior project design team created a proof-of-concept machine. This prototype started as a two-wheel mechanism. Eventually, a third wheel was added, allowing for complete control over disc spin. The three-wheel prototype reached 62 mph when perfectly calibrated. The prototype is accurate, …

Effects Of Alternative Jet Fuels On Aerospace-Grade Composites: Experimental And Modeling Studies, Naoufal Harich

Theses and Dissertations

The aviation industry aims to reduce its environmental impact through innovation and research. The usage of composite materials for multiple primary structures represents one such measure. Several alternative fuels were approved and used along with the Federal Aviation Administration (FAA). These alternative fuels are produced from wastes and biomasses. Some alternative fuels were initially only approved as drop-in fuels, meaning they must be blended with conventional fuels to operate. Fuel tanks are usually embedded into the wing structure, which is mainly made of composite materials. These composites tend to absorb fluids it encounters through their matrix phase. The absorption behavior …

Development Of Mirror Flexures For Use In The Muvi Instrument, Colin W. Harrop

Master's Theses

The Miniaturized Ultraviolet Imager (MUVI), is a compact wide field UV imaging instrument in development at UC Berkeley Space Sciences Laboratory and Cal Poly, San Luis Obispo. MUVI is designed to fit in a 2U CubeSat form factor and provide wide field, high resolution images of the ionosphere at far ultraviolet wavelengths. This thesis details the design and analyses of MUVI’s deployable cover mirror mounting flexures. Three different flexure geometries were evaluated, an optimal candidate was determined based on a number of criteria including isolation of vibration and stress to the mirrors, manufacturability and cost. The design of the flexure …

Jcati Carbon Fiber Recycler: Crusher System, Devin Riley

All Undergraduate Projects

With a substantial rise in Carbon Fiber use across all industries, the need for a way to recycle the waste has grown as well. A group of Mechanical Engineering Technology students at Central Washington University funded by the Joint Center for Aerospace Technology (JCATI) have created a machine to recycle waste wing trimmings from the Boeing company’s airplanes. This machine consists of 5 different sub-assemblies being the oven, crusher, gear train, conveyor, and shredder. The purpose of this project was to decrease the deflection in the crusher caused by bulging in the housing and movement of the bearings. To decrease …

Study Of Nanocomposite Materials Using Molecular Dynamics, Prashik Sunil Gaikwad

Dissertations, Master's Theses and Master's Reports

There is an increase in demand for new lightweight structural materials in the aerospace industry for more efficient and affordable human space travel. Polymer matrix composites (PMCs) with reinforcement material as carbon nanotubes (CNTs) have shown exceptional increase in the mechanical properties. Flattened carbon nanotubes (flCNTs) are a primary component of many carbon nanotube (CNT) yarn and sheet materials, which are promising reinforcements for the next generation of ultra-strong composites for aerospace applications. These flCNT/polymer materials are subjected to extreme pressure and temperature during curing process. Therefore there is a need to investigate the evolution of properties during the curing …

Dynamic Analysis, Characterization, And Design Of Rigid-Flex Pcb Robotics, John Bell

All Dissertations

The era of space exploration is driven by and fuels large advances in technological progress.
Over the last decade, engineering practices for spacecraft, space structures, robotics, software and
hardware, manufacturing techniques, and the implementation of new and novel materials has been
revolutionized. Space exploration pushes the envelope in terms of technological capabilities and
robotic systems (rovers) become lighter, smaller, and more capable of sustaining damage. This
dissertation aids in the advancement of design knowledge for a class of rovers characterized by
their chassis architecture: rigid-flex printed circuit board (PCB) robotics. These rovers leverage
the printed circuit cards as the structural …