Other Mechanical Engineering Commons^™

Prospects For Solving The Problem Of Rational Use Of Water Resources Using The Tiiame-1 Sprinkling Machine, M.Kh. Khamidov, A.R. Muratov

Irrigation and Melioration

The information published by the International Commission on Irrigation and Drainage, and the intermediate results of many years of research carried out by scientists from TIIAME on the development, research and implementation of water-saving technologies in agriculture are presented. The acute shortage of water resources in Central Asia, the problems of increasing the efficiency of the use of water-saving technologies around the world have led to the careful use of available water resources in the region, including the prospects and advantages of using irrigation of crops by sprinkling, as well as the design and technical parameters of the sprinkler developed …

Inadequacy Of Current Water Use Planning At The Level Of Water Users And Wuas, A.A. Alimdjanov, A.Kh. Karimov, B.R. Nasibov

Irrigation and Melioration

This paper studies the main issues of water use planning at the level of water consumers and water user associations (WUA). The study carried out in Bulakbashi district of Andijan province of Uzbekistan, where the main source of irrigation water is the Southern Fergana Main Canal. The study followed two-stage procedure. During the first stage we compiled water use plans for the WUA and water consumers based on the applied methodology of water use planning. Then, at the second stage, we analyzed the results of the actual implementation of the farm water consumption plans and WUA water use plan, and …

Technology And Technical Device Used In The Efficient Use Of Water Resources In Irrigated Agriculture, А.U. Аtajanov

Irrigation and Melioration

The economical use of water resources, the improvement and development of new technology and technical means for its implementation, ensuring the saving of irrigation water is one of the most important issues of today. This article is devoted to the issues of improving the technology of irrigation of furrows and the creation of technical means,also recommended technology and using from created technical device in selected per experiment fields and analyzing their results.

Empirical Assessment Of Climate Change Impacts On Agriculture In Samarkand Region, Sh.B. Babakholov

Irrigation and Melioration

Agricultural production is highly sensitive to climate factors like other endogenous factors, and the expected climate change projections may have a negative impact on the efficiency and income of agricultural producers. Therefore, this study aims to analyze the impact of changes in climatic factors (average air temperature and precipitation) on the technical efficiency of cotton growing farmers as its determinants in Samarkand region. Empirical analyzes were performed on the cases of 1141 cotton-growing farms using panel-based Time-Invariant Inefficiency model. According to the results of the analysis, cotton farms in the region have an average technical efficiency of 76%, which in …

Car Wash Complex – Object Of Harmful Impact On Water Resources, M. Radkevich, K. Shipilova, M. Abdukodirova, O. Pochugevski

Irrigation and Melioration

Deals with the problem of the impact of car wash complexes in the city of Tashkent on water resources. The analysis of the technological process of washing and a sociological survey of car owners and employees of car washes revealed the average amount of water used per car wash per year, as well as the amount of harmful substances entering the sewer network of the city of Tashkent. Calculations have shown that the annual water consumption only for passenger cars in Tashkent is about 4.34 million m³, and the wastewater is not properly treated. From one car wash …

Agrochemical Indicators Of New Irrigated Graph-Meadow Soils Formed On The Iii Underfladder Terrace Of Syrdarya, J.M. Kuziev

Irrigation and Melioration

Presents material on the geographical location, geomorphological and geological structure, as well as the agrochemical state of irrigated serozem-meadow soils, common in the Mirzaabad district of the Syrdarya region. According to the data obtained on the chemical analysis of soils, the studied soils are medium- and heavily loamy in texture, where particles of coarse sand predominate (0.05-0.01%). In the arable horizon of these soils, the humus content is 1.088-1.214%, total nitrogen 0.079-0.089%, total phosphorus 0.109-0.124%, and total potassium within 1.15-1.24%, and on the basis of these data, a regularity of the underlying horizon of these soils. The degree of provision …

Water Efficient Technology Of Drip Irrigation In Intensive Gardens, F.U. Juraev, G.H. Karimov

Irrigation and Melioration

The studies were carried out in 2017-2019 at the Zodabek farm on a 6 hectare garden plot with seedlings of half-tall apple trees “Golden Delicious”. Experimental research work was carried out at a groundwater level in the experimental area of 1.5-2.0 m, mineralization 1.0-1.2 g/l in alluvial, mechanical, medium sandy soils with the following irrigation options. The first option is irrigation, at the start of the second - drip irrigation; third, the use of specially designed soil pegs. The following results were obtained: in the control option, the average irrigation rate for three years was 1125.7 m3/ha, with drip irrigation …

Forecasting The Dynamics Of Cotton Yield In The Ferghana Region, V. Vakhobov, А.А. Faiziev

Irrigation and Melioration

Observations of a certain phenomenon, the nature of which changes over time, give rise to an ordered sequence, which is called a time series. In the article, using the method of statistical time series analysis, statistical pattern of time series Y₁ – average yield of cotton in Fergana region of the Republic of Uzbekistan(on materials of CSB of the Republic of Uzbekistan for 1991-2018 years). Point and interval estimates for the average cotton yield were constructed with a 95% guarantee, explicit types of trends were determined, and the yield in the region was predicted for subsequent years. Using statistical …

Hydraulic Elevator For Purification Of Water Supply Facilities Of The Reservoir, R.R. Ergashev, F. Atrikbekova, H. Khusanboeva, B.T. Kholbutaev, N.A. Babazhanov

Irrigation and Melioration

The purpose of the research is to increase the efficiency of pumping stations operation by improving the methods of uniform flow spreading in the front chamber and inlet of the pumping station and developing constructive measures to improve the hydraulic conditions for supplying the flow to the pumps. The improvement of the method of hydraulic calculation of the flow in the front chamber and the water intake chamber is given on the example of the head pumping station of the Jizzakh cascade. In the process of research, standard methods of full-scale and bench tests of pumps, methods of mathematical and …

Energy-Saving Structure Justification Powerful Tractor And Modern Agricultural Machine, A.K. Igamberdiyev, N.A. Khalikova, N.B. Razikov, O.E. Usarov

Irrigation and Melioration

Discusses the fact that machine-tractor units (MTA) from high-power tractors are often not fully used due to errors in the design and operation of units, their ability to work under certain operating conditions with maximum efficiency and minimum fuel consumption, a method of completing a machine-tractor unit from a high-power technical means is proposed, which ensures the required quality of the technological operation, maximum efficiency and minimum fuel consumption, which must be performed under certain operating conditions. To study the power balance of energy-saving units, consisting of powerful tractors and modern agricultural machinery, an analysis was carried out of a …

Traction Control Of The Friction Drive Of The Vertical Spindle, M. Shoumarova, T. Abdillaev, Sh.A. Yusupov, Ch.A. Shermatova

Irrigation and Melioration

The main indicator in assessing the quality of the work of cotton pickers is its completeness of picking cotton, among the factors that predetermine the completeness of picking a special place is occupied by the direction and magnitude of the absolute speed of the spindle tooth. Among the factors affecting the absolute speed of the tooth, the main place is occupied by the angular speed of rotation of the spindle around its own axis, which depends on the quality of functioning of the friction drive of the spindle. This drive does not always provide its required traction capacity, since due …

Research The Chopper Apparatus Of Equipment For Chopping Pressed Rough Fodders, Sh.H. Gapparov, N.A. Ashurov

Irrigation and Melioration

Livestock is one of the most important agricultural sectors in Uzbekistan and it is based on family livestock farms. On family farms, livestock animals are fed with pressed roughage, including corn stalks, alfalfa hay, barbed straw and wheat straw, mixed with concentrated feed. However, due to the lack of small choppers suitable for small farms, the compressed feed is fed to animals without chopping, as a result of which about 25-30 percent of them go to waste and there are large losses. Taking this into account, a small device was developed for chopping pressed roughage and mixing it with concentrated …

Theoretical Research On Determining The Length Of The Shovels Of A Wheel Of Centrifugal Fans, V.A. Arkhipov, D. Dzhuraev, I.Zh. Toirov, A.E. Urishev

Irrigation and Melioration

Presents the results of theoretical research by scientists, carried out scientific work to determine the length of the shovel of a centrifugal fan wheel. A technological scheme for installing a shovel on a fan wheel disk has been developed Analyzes of these works are carried out, which show that the length of the wheel shovel has a significant dependence on the parameters of the wheel (R, R₁), the angle of installation α and the radius of the arc R₃ of the shovel. An analytical dependence is derived for determining the length of the shovel of a …

Spectral Absorption Coefficient Of Additive Manufacturing Materials, Nicholas J. Wallace, Matthew R. Jones, Nathan B. Crane

Faculty Publications

Active thermography techniques are of interest for quality assurance of additive manufacturing processes. However, accurate measurements of thermophysical properties of materials are required to successfully implement active thermography. In particular, the spectral absorption coefficient of materials commonly used in additive manufacturing must be known to accurately predict the spatial distribution of thermal energy generated from absorption of power emitted by a laser or pulsed flash lamp. Accurate measurements of these optical properties are also needed to develop greater understanding of additive manufacturing processes that rely on radiative heat transfer to fuse powders. This paper presents spectral absorption coefficient measurements and …

Microparticle Propulsion For In Vivo Navigation, Louis Rogowski

Mechanical Engineering Research Theses and Dissertations

Microscale propulsion impacts a diverse array of fields, with simplistic microrobots allowing for novel innovations in microscale surgery and drug delivery. Propulsion at the microscale is constrained by physics, with time-reversal and geometric symmetries limiting available propulsion mechanisms. However, certain fluid environments and surface coatings allow for the propulsion of microparticles through externally applied magnetic fields. Presented here is a detailed analysis of microparticles propelling using spontaneous symmetry breaking, flagella surface coatings, and multi-modal actuation mechanisms. Spontaneous symmetry breaking in nonlinearly viscoelastic fluids is presented for the first time in literature, with two equal and opposite propulsion states existing along …

A Numerical And Experimental Study Of Lid Driven Square Cavity Flow For Laminar And Turbulent Cases, Abdullah Bin Naeem

LSU New Orleans Theses and Dissertations

Experimental and numerical studies are performed on steady and unsteady lid-driven cavity flow for laminar flow regime. In the experiments, a PIV and an LDA were employed to measure the global and local velocities, respectively inside a cavity of AR 1.0. The velocity vector plots and streamline plots which represent unsteady circulation patterns are obtained using the PIV. The steady local velocities measured with LDA are then used to calibrate the PIV measurements. The numerical study is performed using a commercial CFD solver. For turbulent flow simulation RANS equations with K-Epsilon closure model were used. From the PIV calibration study, …

Performance Improvements For Next Generation Falling Particle Receiver Systems, Nathan R. Schroeder

Mechanical Engineering ETDs

Falling particle receiver (FPR) systems are a rapidly developing technology for concentrating solar power applications. Solid particles are used as both the heat transfer fluid and thermal energy storage media. Through the direct solar irradiation of the solid particles, flux and temperature limitations of tube-bundle receives can be overcome leading to higher operating temperatures and energy conversion efficiencies. Particle residence time, curtain opacity, and curtain stability affect the performance of FPR designs. As the particles fall through the receiver the curtain accelerates, increasing its transmissivity thus decreasing the amount of energy absorbed. Multistage release trough structures catch and release the …

Understanding Of Aerosol Transmission Of Covid 19 In Indoor Environments, Adama Barro, Cathal O'Toole, Jacob S. Lopez, Matthew Quinones, Sherene Moore

Publications and Research

Our reason for discussing severe acute respiratory syndrome corona virus 2 (SARS-CoV-2) or 2019 novel corona virus (Covid-19), is to understand its aerosol transmission characteristics in indoor spaces and to mitigate further spread of this disease by designing a new HVAC system. The problem that we are tackling is the spread of covid-19 droplets through aerosol transmission by looking at potential engineering solutions to the existing HVAC systems. The purpose is to eradicate the spread of the COVID-19 by testing indoor spaces in an effort to understand the effectiveness of ventilation controls. We believe that scientists and engineers have not …

Direct Solar Absorption Nanoparticle Doped Membranes For A Hybrid Membrane Distillation And Photovoltaic Cell, Alejandro Espejo Sanchez

Boise State University Theses and Dissertations

The growing demand for clean water supplies is driving the need for an innovative approach of water desalination. Developing a method for treating water with high salinities is possible with membrane distillation (MD). Additionally, MD is very attractive for pairing with solar energy due to the low temperature requirements. The integration of a membrane distillation system with a photovoltaic (PV) system will result in the co-production of electricity and clean water, thereby improving the economics of MD. Such a hybrid system will directly absorb thermal energy in the membrane for desalination while taking advantage of the spectrally selective nature of …

A.C. Moyer Eye-Cap Manufacturing, Thais Bertolus, Alexa Steidl, Hana Welsh, Jarod Kinney, Maya Willis

Mechanical Engineering

A.C. Moyer company has been making eye caps as a family business since 1947. Eye caps are a product used during the embalming process. Currently the machines being used to produce the eye caps are outdated and unsafe. We are a team of 5 mechanical engineering students tasked with either designing new machines or updating the existing machines to make the manufacturing process more efficient, automated, and safer. This document describes the design process, provides background, relevant research, establishes project objectives, and defines plans for project implementation.

Improvement Of Labyrinth Seal Leakage Rates Using Additive Manufacturing, Austin L. Gasbarra

Master's Theses

The growing popularity of additive manufacturing in commercial applications has al- lowed for new ideas and new ways of thinking when designing components. Further optimization at the component level is possible, though powder metallurgy is in its infancy. This study explores the possibility of using additive manufacturing to develop better labyrinth seals in turbomachinery. Labyrinth seals have a torturous fluid path with high losses, thus limiting the amount of fluid leakage. These types of seals can be non-rotating, allowing them to better take advantage of the additive manufacturing process due to the absence of rotating stresses. Labyrinth seal performance is …

Sustainable Drug Release From Polycaprolactone Coated Chitin‑Lignin Gel Fibrous Scaffolds, Turdimuhammad Abdullah, Kalamegam Gauthaman, Azadeh Mostafavi, Ahmed Alshahrie, Numan Salah, Pierfrancesco Morganti, Angelo Chianese, Ali Tamayol, Adnan Memic

Department of Mechanical and Materials Engineering: Faculty Publications

Non-healing wounds have placed an enormous stress on both patients and healthcare systems worldwide. Severe complications induced by these wounds can lead to limb amputation or even death and urgently require more effective treatments. Electrospun scaffolds have great potential for improving wound healing treatments by providing controlled drug delivery. Previously, we developed fibrous scaffolds from complex carbohydrate polymers [i.e. chitin-lignin (CL) gels]. However, their application was limited by solubility and undesirable burst drug release. Here, a coaxial electrospinning is applied to encapsulate the CL gels with polycaprolactone (PCL). Presence of a PCL shell layer thus provides longer shelf-life for the …

Data Analysis To Evaluate The Performance Of Breathing Masks Used For Filtering Nano-Level Particles At Manufacturing Sites, Gracia M. Dardano

Honors College Theses

The work performed in this research aims to evaluate the performance of commercially available breathing masks in filtering airborne nanoparticles at manufacturing sites. Nanoparticles are found virtually anywhere, from dust in a worksite to a simple sneeze. Therefore, they pose a substantial threat to human health as their velocity and volatility are high. This research analyzes if current efforts of breathing masks to hinder nanoparticles are effective, especially at manufacturing sites. Data has been collected in order to analyze the behavior of nanoparticles and to measure nanoparticle levels at manufacturing sites and its working environment. Data is statistical in nature …

Centrifugal Microfluidic Platform For Solid-Phase-Extraction (Spe) And Fluorescence Detection Applications, Yong Zhang

LSU Doctoral Dissertations

Solid phase extraction (SPE) is a widely used method to separate and concentrate the target molecules in liquid mixture. Traditional SPE has to be conducted in the laboratory with professional equipment and skilled operators. The microfluidic and 3D printing technology have opened up the opportunity in developing miniaturized automatic instruments. The main contribution of this research is to integrate the SPE process on a novel centrifugal platform. Various valves are applied on the platform to help control the aqueous sample and reagents in the cartridge.

First, a centrifugal microfluidic platform was built for automatically detecting trace oil pollution in water. …

Bibliometric Survey On Supply Chain In Healthcare Using Artificial Intelligence, Shruti Maheshwari, Gagandeep Kaur, Ketan Kotecha, Pramod Kumar Jain Dr.

Library Philosophy and Practice (e-journal)

With the increasing demand for the supply chain in the service sector, new techniques have become essential. With the latest emerging technologies, it has become crucial to have a bibliometric analysis of supply chain management (SCM) in the healthcare sector. The paper represents the analysis of research supply chain in the service sector using artificial intelligence techniques. The main aim of the analysis is to accomplish the technology in healthcare supply chain management using SCOPUS, Google Scholar, Research Gate, etc. and the various softwares like Gephi, GSP Visualizer, etc. The bibliometric analysis shows that India has ranked 4th in publishing …

Portable Wind Turbine Blade Leading Edge Erosion Test, Joe Blakewell, Tim Holt, Kevin Vartan

Mechanical Engineering

Turbine Technology Partners, LLC (TTP) is a company located in Santa Barbara, California that provides expert independent engineering (IE) consulting services to the wind energy industry - supporting its goal of generating cost effective and reliable carbon-free renewal energy for the world. TTP customers include some of the largest wind turbine original equipment manufacturers (OEMs), wind turbine power plant developers, and wind turbine owner/operators. One of the biggest problems challenging the wind energy industry currently is the power loss that results from the leading edge (LE) erosion of wind turbine blades. The purpose of our senior design project is to …

Bolted Flanged Assembly Test Stand, Mark Christian Damasco Sunga, Paulina Mercedez Delgado, Philip John Coleman

Mechanical Engineering

The following Final Design Report (FDR) is the last formal documentation for the senior design project. The project was carried out by three senior mechanical engineering students at California Polytechnic State University, San Luis Obispo for Phillips 66. The project proposed was to design a test stand and implement a procedure which will evaluate craftsmen’s abilities to assemble a bolted flanged joint assembly. The goal was to create a fully functional test setup that can be duplicated and utilized throughout Phillips 66’s refineries. This document details the design process that was completed over the course of three quarters, including concept …

Deep-Sea Water Collector, Chandler Jones, Jenny Verheul, Michael Di Giorgio

Mechanical Engineering

Properties such as nutrients, DNA, pH levels, and primary productivity are difficult to measure onboard an Underwater Remotely Operated Vehicle (UROV) as mobile submarine sensors are highly expensive and conventional water capture devices are too large to be equipped. However, these properties provide an integral view into our oceans, the species that inhabit them, and our influence on the environment. Collected samples of seawater taken back to labs allow researchers to see a clearer picture of ecosystems’ inhabitants and lifecycle with the analysis of Environmental DNA (eDNA) among many other properties. The scope of this project is to design a …

Extending The Functional Subnetwork Approach To A Generalized Linear Integrate-And-Fire Neuron Model, Nicholas Szczecinski, Roger Quinn, Alexander J. Hunt

Mechanical and Materials Engineering Faculty Publications and Presentations

Engineering neural networks to perform specific tasks often represents a monumental challenge in determining network architecture and parameter values. In this work, we extend our previously-developed method for tuning networks of non-spiking neurons, the “Functional subnetwork approach” (FSA), to the tuning of networks composed of spiking neurons. This extension enables the direct assembly and tuning of networks of spiking neurons and synapses based on the network’s intended function, without the use of global optimization ormachine learning. To extend the FSA, we show that the dynamics of a generalized linear integrate and fire (GLIF) neuronmodel have fundamental similarities to those of …

Optimal Control Of Active Nematics, Michael M. Norton, Piyush Grover, Michael F. Hagan, Seth Fraden

Department of Mechanical and Materials Engineering: Faculty Publications

In this work we present the first systematic framework to sculpt active nematic systems, using optimal control theory and a hydrodynamic model of active nematics. We demonstrate the use of two different control fields, (i) applied vorticity and (ii) activity strength, to shape the dynamics of an extensile active nematic that is confined to a disk. In the absence of control inputs, the system exhibits two attractors, clockwise and counterclockwise circulating states characterized by two co-rotating topological þ1 2 defects. We specifically seek spatiotemporal inputs that switch the system from one attractor to the other; we also examine phase-shifting perturbations. …