Other Mechanical Engineering Commons^™

Thermal Modeling Techniques For Additively Manufactured Porous Metals, Lucas D. Rambo

Master's Theses

Advances in additive manufacturing have enabled the creation of metallic components with tailored porosity, offering design flexibility for thermal, structural, and fluid transport applications. This thesis investigates the effective thermal conductivity (ETC) of porous Inconel 625 (IN625) and Inconel-ceramic composites (IN625-RAM2) fabricated by Laser Powder Bed Fusion (LPBF) using Elementum 3D’s PermiAM technology. Experimental measurements of thermal conductivity using the laser flash method are compared to numerical models built from micro-computed tomography data. Simulations were performed using both finite element (FE) and finite volume (FV) methods to evaluate thermal transport in real microstructures. The study investigates the effects of micro- …

A Computational Fluid Dynamics Approach To Analyze The Virtual Impactor In Pneumatic Aerosol Jet Printing, Akashita Sareen

Theses, Dissertations and Capstones

Aerosol jet printing (AJP) is a 3D printing, advanced manufacturing process that generates an aerosol mist appropriate for fine printing small, low-volume electronic parts. The pneumatic aerosol jet printing technology’s virtual impactor is the focus of this study. In this technology, high velocity nitrogen gas aerosolizes various inks in the atomizer. The aerosolized stream of ink is then transported to a virtual impactor (VI) to become dense and concentrated as it begins to enter the deposition head for high precision electronics printing. AJP faces challenges in large-scale adoption due to challenges related to overspray, instability, ink clogging etc. There is …

Transient Thermal Finite Element Simulation For Process Modeling In Wire Arc Additive Manufacturing, Satya Sai Kumar Pilli

Dissertations, Master's Theses and Master's Reports

This thesis presents the development of a transient thermal framework for Wire Arc Additive Manufacturing (WAAM) created using ANSYS Workbench. This study aims to understand the inherent properties and thermal behavior of WAAM by using the Finite Element (FE) simulation technique to reduce the need for experiments. Specifically, the transient thermal WAAM simulation framework uses the heat source Goldak model to understand the thermal behavior for a given voltage, initial temperature, and travel speed during the process to predict process temperature. The outcomes of this thesis aim to significantly decrease material waste and repetitive experiments and accelerate production process design …

Effect Of Build Orientation On Tensile Properties And Fractography Of Additive Manufactured Inconel 718 Alloy, Ajay Kumar Maurya, Amit Kumar, Swarnambuj Suman

ASEAN Journal on Science and Technology for Development

The additive manufacturing (AM) technique “Direct Metal Laser Sintering (DMLS)” is used to create 3D objects directly from 3D design data. A lightweight and complexity-free part without any expensive tooling can be fabricated easily using this method, but it is still challenging to achieve the desired mechanical strength from AM parts, as the mechanical properties of AM-produced parts vary with orientation, scan strategy, and process parameters. Inconel 718 alloy is most commonly utilized in the aerospace and automotive industries, because of its high resistance to corrosion and excellent mechanical qualities. This work presents a study to investigate the orientation-based mechanical …

Focused Led Sintering, Dylan Defazio, Nilav Maulik, Branden Majors, Michael Fontillas

Mechanical Engineering

This report provides a detailed overview of the final design of our light-emitting diode (LED) focusing system. Our system incorporates a converging lens and a specially designed "glass funnel," which acts as a thick fiber optic that narrows the light to a fine point through internal reflection. The glass components of our system are precisely housed in a part made using advanced computer-numeric controlled (CNC) Mill and CNC Lathe manufacturing processes. This ensures high precision and durability of the overall system. Our LED focusing system is designed with a 60-watt stage light. The decision to use a glass funnel as …

Cycle Time Reduction In Additive Manufacturing Using Peltier Thermoelectric Cooling Devices, Trevor Carlton

Honors College Theses

Thermoelectric cooling and the Peltier effect were discovered in 1834, over 188 years ago. Additionally, the first iterations of additive manufacturing (i.e., 3D printing) began in the early 1980s, more than 40 years ago. Despite these technologies’ age and years of advancements, the application of Peltier cooling-based devices in additive manufacturing has not yet been realized. These devices can be used for the active thermal management of print beds in 3D printers. Developing a mechanism to heat and cool a print bed can reduce the cycle time to manufacture a part. In 3D printing, waiting for the heated bed to …

Recycled Printer Filament, Charlotte Hyland, Troy D. Molinar

Williams Honors College, Honors Research Projects

The purpose of this research is to examine the effects of recycling PLA filament for 3D printing on its material properties. After examining these effects, PLA and carbon fiber additives were mixed with recycled PLA pellets in different ratios to attempt to regain material properties lost in the recycling process. To complete these findings, an experiment was design and executed.

The research found that tensile strength during multiple iterations of recycling remained mostly unaffected, however, the strain degraded exponentially. In the PLA additive study, high ratios of PLA additive were able to increase the strength and strain properties of the …

Rheology Of Particulate Suspensions With Non-Newtonian Fluids In Capillaries, Bin Xia, Paul Krueger

Mechanical Engineering Research

This resource contains the processed experimental measurements of the flow consistency index and flow behavior index, along with their trendlines, for the particulate suspensions investigated in "Rheology of Particulate Suspensions with Non-Newtonian Fluids in Capillaries" by Bin Xia and Paul S. Krueger.

Design For Additive Manufacturing (3d Printing), Michael O'Donnell, Michael J. Levy

Williams Honors College, Honors Research Projects

The goal of this project is to study the performance of a 3D printed mechanical part subjected to topology optimization. A part that is somewhat complex in its load bearing and geometry will be selected. That part will then be designed, finite element analysis will be performed on it to optimize its topology, and then it will be 3D printed and tested. The goal of topology optimization is to either save material cost and/or part weight due to the ability of 3D printing to manufacture parts with complex and obscure geometry.

Improvement Of Labyrinth Seal Leakage Rates Using Additive Manufacturing, Austin L. Gasbarra

Master's Theses

The growing popularity of additive manufacturing in commercial applications has al- lowed for new ideas and new ways of thinking when designing components. Further optimization at the component level is possible, though powder metallurgy is in its infancy. This study explores the possibility of using additive manufacturing to develop better labyrinth seals in turbomachinery. Labyrinth seals have a torturous fluid path with high losses, thus limiting the amount of fluid leakage. These types of seals can be non-rotating, allowing them to better take advantage of the additive manufacturing process due to the absence of rotating stresses. Labyrinth seal performance is …

Design Rules For Additive Manufacturing – Understanding The Fundamental Thermal Phenomena To Reduce Scrap, M. Reza Yavari, Kevin D. Cole, Prahalada K. Rao

Department of Mechanical and Materials Engineering: Faculty Publications

The goal of this work is to predict the effect of part geometry and process parameters on the direction and magnitude of heat flow heat flux in parts made using metal additive manufacturing (AM) processes. As a step towards this goal, the objective of this paper is to develop and apply the mathematical concept of heat diffusion over graphs to approximate the heat flux in metal AM parts as a function of their geometry. This objective is consequential to overcome the poor process consistency and part quality in AM. Currently, part build failure rates in metal AM often exceed 20%, …