Other Mechanical Engineering Commons^™

Development Of Dynamic Proof-Mass Configurations For Broadband Piezoelectric Energy Harvesting, Nico E. Galarza

Electrical and Computer Engineering ETDs

The purpose of this thesis is to investigate and develop dynamic proof-mass configurations for broadband piezoelectric energy harvesting. Conventional piezoelectric energy harvesters are typically limited by narrow operating bandwidths, restricting their performance under variable-frequency excitation. This research presents the design, fabrication, and experimental evaluation of multiple proof-mass concepts intended to increase the usable frequency range of cantilever-based piezoelectric energy harvesters. Several dynamic mass configurations were developed using additive manufacturing techniques and integrated with commercially available piezoelectric cantilevers. Experimental testing was conducted under controlled vibration conditions to characterize voltage response, resonant behavior, and bandwidth performance. The results demonstrate that dynamic proof-masses …

Analysis Of Ternary Chloride Salt Corrosion In High Nickel Alloys, Dimitri Madden, Gowtham Mohan

Mechanical Engineering ETDs

The United States Department of Energy seeks to improve the efficiency of concentrating solar power technologies by employing thermal energy storage with operating temperatures above 700°C. To meet these goals, the National Solar Thermal Test Facility at Sandia National Laboratories has considered the use of a ternary molten chloride salt for sensible heat storage systems. While favored for low cost, good heat transfer properties, and stability at high temperature, ternary chloride salt also exhibits high corrosive attack. Components of a chloride salt storage system would include piping, valves, tanks, pumps, receivers, and heat exchangers, which would be exposed to high …

Performance Improvements For Next Generation Falling Particle Receiver Systems, Nathan R. Schroeder

Mechanical Engineering ETDs

Falling particle receiver (FPR) systems are a rapidly developing technology for concentrating solar power applications. Solid particles are used as both the heat transfer fluid and thermal energy storage media. Through the direct solar irradiation of the solid particles, flux and temperature limitations of tube-bundle receives can be overcome leading to higher operating temperatures and energy conversion efficiencies. Particle residence time, curtain opacity, and curtain stability affect the performance of FPR designs. As the particles fall through the receiver the curtain accelerates, increasing its transmissivity thus decreasing the amount of energy absorbed. Multistage release trough structures catch and release the …

Experimental Investigation Of The Wind Energy Harvesting Potential Of A Stand-Alone Piezoelectric Strip, Phillip Christopher Scott

Mechanical Engineering ETDs

The purpose of the study was to investigate the feasibility of harvesting wind energy on a small scale in residential areas. The method investigated was the initiation of movement-induced excitation (MIE), a type of aeroelastic flutter, within samples of polyvinylidine fluoride (PVDF), a piezoelectric polymer. Single samples of PVDF were secured in a wind tunnel and sample voltage was measured over a broad range of wind speeds. Power was calculated then via the addition of ohmic resistance matched to the magnitude of the capacitive impedances of the samples. The geometry of the PVDF samples studied was maintained as a simple …

The Development Of All Solid-State Optical Cryo-Cooler, Junwei Meng

Optical Science and Engineering ETDs

This dissertation describes the development of an all solid-state optical cryo-cooler. Crystals of 10% wt. ytterbium-doped yttrium lithium fluoride (Yb³⁺:YLF) are used to cool an infrared HgCdTe sensor payload to an absolute temperature below 135 K, equivalent to delta T equal 138 K below ambient. This record level of cooling is accomplished with a single stage, in a completely vibration-free environment, with a corresponding cooling power of 190 mW. This milestone is made possible by the design and fabrication of an undoped YLF thermal link that efficiently shields the payload with a non-right angle kink from intense anti-Stokes …

Emissivity Measurements Of Painted And Aerosol Deposited Thermographic Phosphors (Yag:Dy And Mfg:Mn), Wendy Flores-Brito

Mechanical Engineering ETDs

Combustion is one of the most difficult processes to model. Luminous flames are characteristically sooty, which creates a problem when modeling and calculating the combustion and heat transfer of the process; both of which are highly dependent on temperature and emissivity. Soot particle emissivity as well as gas contributions affect the heat transfer calculation and must be accounted for.

Thermographic phosphors (TP) are ceramic based phosphorescent materials that have a temperature dependent emission that can be exploited to obtain surface and gas temperature measurements, as well as 2D temperature maps. Emissivity knowledge is not needed to obtain temperature and is …

Characterization Of Single- And Multi-Phase Shock-Accelerated Flows, Patrick John Wayne

Mechanical Engineering ETDs

Experiments conducted in the Shock Tube Facility at the University of New Mexico are focused on characterization of shock-accelerated flows. Single-phase (gaseous) initial conditions consist of a heavy gas column of sulfur hexafluoride seeded with approximately 11% acetone gas by mass. Visualization of the image plane for gaseous initial conditions is accomplished via planar laser-induced fluorescence (PLIF) with a high-powered Nd:YAG ultraviolet laser and an Apogee Alta U-42 monochrome CCD camera, with a quantum efficiency > 90%. Multi-phase (gas-solid) initial conditions consist of glass micro-beads deposited on small 1-cm diameter discs of specific surface chemistry, mounted flush with the bottom wall …

Detection And Classification Of Vibrating Objects In Sar Images, Francisco German Perez Venegas

Electrical and Computer Engineering ETDs

The vibratory response of buildings and machines contains key information that can be exploited to infer their operating conditions and to diagnose failures. Furthermore, since vibration signatures observed from the exterior surfaces of structures are intrinsically linked to the type of machinery operating inside of them, the ability to monitor vibrations remotely can enable the detection and identification of the machinery.

This dissertation focuses on developing novel techniques for the detection and M-ary classification of vibrating objects in SAR images. The work performed in this dissertation is conducted around three central claims. First, the non-linear transformation that the micro-Doppler return …

Investigating The Classical And Non-Classical Mechanical Properties Of Gan Nanowires, Mohammad Reza Zamani Kouhpanji

Electrical and Computer Engineering ETDs

Study and prediction of classical and non-classical mechanical properties of GaN is crucial due to the potential application of GaN nanowires (NWs) in piezoelectric, probe-based nanometrology, and nanolithography areas. GaN is mainly grown on sapphire substrates whose lattice constant and thermal expansion coefficient are significantly different from GaN. These discrepancies cause mechanical defects and high residual stresses and strains in GaN, which reduce its quantum efficiency.

Specifically, for nanoscale applications, the mechanical properties of materials differ significantly compared to the bulk properties due to size-effects. Therefore, it is essential to investigate the mechanical properties of GaN NWs using the non-classical …

Simulation And Analysis Of A Drilling Fluid Using A Herschel-Bulkley Model, Daniel Powell

Mechanical Engineering ETDs

In the study, a drilling fluid with known properties is analyzed and simulated in the laminar regime through a pipe with dimensions of 1.5m in length and 0.02m in diameter. The purpose of the conducted analysis is to demonstrate the advantages of the Herschel-Bulkley model currently used in the oil and gas industry for analyzing non-Newtonian drilling fluids.

For comparison, the analysis is also performed using more simple models for non-Newtonian fluids such as the Bingham Plastic model and the Power Law model and for a Newtonian fluid (water). In addition to analytical models, computations are conducted using …