Other Mechanical Engineering Commons^™

Prediction Of Satellite Temperature During An Orbit Of A Cubesat, Michael Reynolds

Honors Theses

This thesis develops a thermal-simulation strategy for predicting CubeSat component temperatures, applied to Jag-Sat-1, a CubeSat developed at the University of South Alabama and deployed from the International Space Station in 2022. The orbit was reconstructed from two-line element (TLE) data using simplified general perturbations (SGP4) propagation, and spacecraft attitude was recovered from onboard gyroscope measurements. Sunlight, penumbra, and umbra intervals were computed geometrically, and the external radiative environment — direct solar, Earth infrared, and albedo heat fluxes — was modeled using orientation-dependent view factors. These time-varying fluxes drove a transient finite-element thermal simulation of the full satellite geometry in …

Design And Optimization Of Aquaculture Gear: Development Of A Cage-Integrated Reeling Mechanism For Oyster Farming, Felicity Bryant

Honors Theses

This project encompasses the design, fabrication, and testing of a cage-integrated reeling system aimed at reducing the physical labor required in oyster aquaculture at Bama Bay Oyster Farm, the last operational oyster farm in Mobile Bay. The proposed system includes two primary components: lightweight, modular oyster cages and a dual-winch reeling device for automated retrieval. Three cage prototypes—rectangular, oval, and hexagonal—were evaluated for structural performance and fabrication feasibility. The oval design was ultimately excluded due to practical fabrication limitations. The rectangular and hexagonal designs were fabricated using recycled materials and tested under the most extreme environmental conditions derived from years …

Reconfigurable Python Autopilot Software For Rc Aircraft, Kate Doiron

Honors Theses

No abstract provided.

Effects Of The Gravity Gradient On The Path Of 1i/‘Oumuamua, Hannah R. Richardson

Honors Theses

In October 2017, the asteroid 1I/’Oumuamua first passed into viewing range [1]. The asteroid is notable for being the first interstellar object to enter the solar system. 1I/’Oumuamua was also unusual in its geometry; it is thought to have an aspect ratio of 6:1 and a length of approximately 400 m [2] [3]. The asteroid was observed to experience a non-Keplerian acceleration estimated to be on the order of 1⇥10−6 m s2 . Several theories have been proposed for the cause of this acceleration, all of which are non-gravitational in nature: volatile outgassing, photon pressure, and solar winds [1][4]. However, …

Autonomous Control Of A Hybrid Unmanned Aerial Towed System On A Moving Platform, Zachary M. Miller

Graduate Theses and Dissertations (2019 - present)

With tethered rotor drones being more popular for aerial surveillance, moving platforms for tethered drones are being researched. However, these systems require constant power to the rotor drones for stabilization. With this difficulty in power consumption, a hybrid drone solution is presented. The hybrid drone is similar to an airplane, with quadcopter motors attached for stabilization and thrust when not moving.

The controller for the hybrid drone was tested and verified in simulation. The simulation of the system was built in Fortran and consists of a driver, a tether, and a hybrid drone. The driver was modeled after a generic …

Improving The Viability Of Continuous Fiber Reinforced Composite Materials In Extreme Temperature Applications And Additive Manufacturing, Ryan A. Warren

Shelby Hall Graduate Research Forum Presentations

Presentation slides for a presentation given at the 1st annual Shelby Hall Graduate Research Forum at the University of South Alabama.

Examining The Efficacy Of Using Irt As An Nde Method For Cfrp And Ztcfrp Composites, William Wyatt Taylor

Graduate Theses and Dissertations (2019 - present)

A film adhesive is commonly used to form the bond-line between composite parts. The bond-line's quality and performance can be affected by defects such as voids, impurities, and agglomerations. Identifying these defects is possible with non-destructive evaluation testing (NDE). In this thesis, the joule-heating effect (JH) through carbon nanofiber (CNF) and carbon nanotube (CNT) modified film adhesive bonded to control carbon fiber reinforced polymer (CCFRP) was used along with infrared thermography testing (IRT) for bond-line defect inspection as a preliminary study. Due to the difference in the electrical conductivity between the modified epoxy and the defect, JH can cause a …

Enhancement Of Interlaminar Shear Strength Of Carbon Fiber Reinforced Polymer Composites With Freeform 3d Printing Using Magnetic Compaction & Zt-Cfrp Technologies, Mohammad Rakibul Islam

Graduate Theses and Dissertations (2019 - present)

Carbon Fiber Reinforced Polymer (CFRP) laminates often exhibit matrix-sensitive weaknesses and flaws when produced via conventional additive manufacturing (AM) techniques due to the introduction of voids and defects during the AM process. This thesis employs a new approach called Magnetic Compaction Force Assisted-Additive Manufacturing (MCFA-AM) to fabricate Carbon Nanofibers (CNF)Z-threaded CFRP (i.e., ZR-CFRP) composite laminates. This novel method utilized a magnetic force to simultaneously levitate, deposit, and compact Continuous Carbon Fiber Reinforced Polymer (C-CFRP) composites in free space and rapidly solidifies the CFRP part without any mold; and effectively reduces the voids. Previous studies have demonstrated that the incorporation of …