Mechanical Engineering Commons^™

Dynamic Aeroelastic Response Of Stall-Controlled Wind Turbine Rotors In Turbulent Wind Conditions, Sara Jalal, Fernando L. Ponta, Apurva Baruah, Anurag Rajan

Michigan Tech Publications, Part 1

With the current global trend of the wind turbines to be commissioned, the next generation of state-of-the-art turbines will have a generating capacity of 20 MW with rotor diameters of 250 m or larger. This systematic increase in rotor size is prompted by economies-of-scale factors, thereby resulting in a continuously decreasing cost per kWh generated. However, such large rotors have larger masses associated with them and necessitate studies in order to better understand their dynamics. The present work regarding the aeroelastic behavior of stall-controlled rotors involves the study of the frequency content and time evolution of their oscillatory behavior. A …

Experimental Study Of Drying Yacon Tubers, U K. Khujakulov, Sh A. Sultanova, J E. Safarov

Technical science and innovation

This study discusses the method and experimental drying unit for drying yacon tubers at different temperatures. And also the scheme of experimental drying unit is given, which controls temperature, speed of warm air and shows the mass of dried material. The cross-sectional area of the flow in the tunnel is 20×20 cm, the thermal air passed horizontally through a chute with holes and a surface area of 12×12 cm. The exhaust gas did not circulate in this experiment. The accuracy of the temperature control system was 0.1 °C, the weight control system 0.1 g. The variation of moisture ratio depending …

Electric Vehicle Internal Support System, M A. Xudoyberdiyev, L V. Kravchenko, J E. Safarov, B B. Tuychiboyev

Technical science and innovation

At present, it remains relevant to protect the environment around the world, to prevent the deterioration of ecology, to ensure the health of people, to reduce the amount of exhaust gases emitted into the atmosphere in the preservation of the animal world. Currently, in solving these pressing problems, instead of cars with internal combustion engines, which are used in the automotive industry, energy-efficient electric cars that meet the modern demand, produce less exhaust gases to the environment, work without noise, have a high level of manageability, traction and braking dynamics, stability, safety and comfortability. During the use of these electric …

Causes Of Rolling Stock Brake Equipment Failures, O T. Kasimov, Sh I. Mamaev, A V. Grishenko

Technical science and innovation

Reliable operation of the rolling stock and devices of railway transport is the basis for ensuring the throughput and transport capacity of railways, as well as safety.The article is dedicated to the current day of the topical topic: increasing the reliability and analyzing the causes of brake equipment failures in locomotives in the conditions of JSC "Uzbekistan Temir Yollari".On the rolling stock of railways of JSC "Uzbeksiton Temir Yullari" five types of brakes are used: parking (manual), pneumatic, electro-pneumatic, electric (dynamic and reversible), magnetic-rail and are used as additional to EPT.The article presents an analysis of the …

Evaluating Stem Course Re-Design Strategies In Light Of Covid-19, Ulises Juan Trujillo Garcia, Krishna Pakala, Samantha Schauer, Diana Bairaktarova, Bhaskar Chittoori

Mechanical and Biomedical Engineering Faculty Publications and Presentations

The COVID-19 pandemic brought on unprecedented challenges to the teaching and learning communities that required faculty to make purposeful changes in their teaching approaches. Many faculty members had to shift rapidly from in-person to online mode of instruction. This study documents perceptions of STEM faculty who made the change to online teaching. It reports on what strategies faculty used to transition to remote/online teaching and how this change impacted student learning. The study results indicated that almost two-thirds of the faculty changed how they evaluated their students. Results also showed that the sudden change to remote learning negatively impacted student …

Embedded Curriculum With Industry-Recognized Certifications To Improve The Marketability Of Engineering Technology Graduates, Immanuel Edinbarough, Jesus A. Gonzalez-Rodriguez

Manufacturing & Industrial Engineering Faculty Publications

Embedded Curriculum with Industry Recognized Certifications to Improve the Marketability of Engineering Technology Graduates

The Fourth Industrial Revolution is challenging the industries to change the way they manage and operate the manufacturing environment. This leads to the transformation of the world through artificial intelligence, next-generation robotics, automation, big data analytics, 5G technology and Internet of Things. This idea of Industry 4.0 forces the change in the industries of today and tomorrow. In this, cyber physical systems communicate with one another using the Internet of Things. The manufacturing sector takes full advantage of these technologies to produce innovative products to enhance …

Lagrangian And Eulerian Accelerations In Turbulent Stratified Shear Flows, Frank G. Jacobitz, Kai Schneider

School of Engineering: Faculty Scholarship

The Lagrangian and Eulerian acceleration properties of fluid particles in homogeneous turbulence with uniform shear and uniform stable stratification are studied using direct numerical simulations. The Richardson number is varied from Ri=0, corresponding to unstratified shear flow, to Ri=1, corresponding to strongly stratified shear flow. The probability density functions (pdfs) of both Lagrangian and Eulerian accelerations have a stretched-exponential shape and they show a strong and similar influence on the Richardson number. The extreme values of the Eulerian acceleration are stronger than those observed for the Lagrangian acceleration. Geometrical statistics explain that the magnitude of the Eulerian acceleration is larger …

Methods , Systems , And Devices Relating To Surgical End Effectors, Shane M. Farritor, Thomas Frederick, Joe Bartels

Department of Mechanical and Materials Engineering: Faculty Publications

The embodiments disclosed herein relate to various medical device components , including components that can be incorporated into robotic and / or in vivo medical devices, and more specifically including end effectors that can be incorporated into such devices. Certain end effector embodiments include various vessel cautery devices that have rotational movement as well as cautery and cutting functions while maintaining a relatively compact structure. Other end effector embodiments include various end effector devices that have more than one end effector.

Reduced-Order Modeling Of Loosening In Bolted Joints And Dynamic Interactions Between Axially Aligned Threaded Joints, Sandro Aldana

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Maintaining effective preload in bolted joints is critical for ensuring long-term performance and safety throughout the operation of any assembled structure. The loosening of bolted joints has been studied since the Industrial Revolution, but modeling approaches have only emerged over the past three decades. Although existing approaches are capable of simulating or predicting loosening in a single joint consisting of a single bolt, they are too computationally expensive to be used to model loosening in large structures consisting of many bolts. The objective of this thesis is to construct and employ a reduced-order modeling (ROM) approach that treats the internal …

Optimization Of Mechanical Properties At The Infarct Border Zone, Kaushik Sunder

LSU Master's Theses

A myocardial infarction (MI) occurs every 39 seconds in the United States. As of 2016, an estimated 550,000 new and 200,000 recurrent episodes of myocardial infarction (MI) occur each year in the United States was. Infarction is often distinguished by a considerable decrease in wall thickness and an increase in heart size or left ventricular volume. This behavior happens when there is a prolonged lack of blood flow, usually due to damage or clotting, which causes cardiomyocytes to die (CMs). The development of non-contractile infarct scarring is the primary pathophysiology of MI. While the infarct scar prevents myocardial rupture during …

Incorporating A Mid-Semester Project To Evaluate Communication, And Leadership Skills For Undergraduate Engineering Students In The Statics/Strength Of Materials Course: A Comparative Assessment Before And During Covid-19, Eleazar Marquez, Samuel Garcia

Mechanical Engineering Faculty Publications

In this research study, a Popsicle-bridge project was assigned to a cohort of undergraduate engineering students enrolled in a Statics and Strength of Materials Course to enhance technical, communication, and leadership skills when working in a group setting. In most undergraduate engineering courses, the technical content is primarily emphasized for the academic development of the student. However, a practicing engineer must be able to possess and apply communication and leadership skills, which are often excluded from the existing curriculum. The first assessment of this project was completed with a cohort of 85 students in the Fall of 2019 before the …

An Improved Earned Value Management Method Integrating Quality And Safety, Brian Briggs

LSU Doctoral Dissertations

The construction industry invests significant time and money to improve quality and safety while reducing cost and schedule impacts. The industry has a sincere desire to improve construction project management methods to improve efficiency. Historically, quality and safety underperformances result from undermanaged quality control and safety activities. The cost and schedule impacts associated with poor quality work have always had an impact on construction operations. The unprecedented challenges and uncertainties of COVID-19 highlighted the need to improve the Earned Value Management (EVM) method within construction to reflect these quality and safety activities. The central goal of this dissertation is to …

Study Of Friction And Wear Effects In Aluminum Parts Manufactured Via Single Point Incremental Forming Process Using Petroleum And Vegetable Oil-Based Lubricants, Jose M. Diabb Zavala, Oscar Martinez-Romero, Alex Elias-Zuniga, Hector Manuel Leija Gutierrez, Alejandro Estrada-De La Vega, Jaime Taha-Tijerina

Manufacturing & Industrial Engineering Faculty Publications

This paper focuses on studying how mineral oil, sunflower, soybean, and corn lubricants influence friction and wear effects during the manufacturing of aluminum parts via the single point incremental forming (SPIF) process. To identify how friction, surface roughness, and wear change during the SPIF of aluminum parts, Stribeck curves were plotted as a function of the SPIF process parameters such as vertical step size, wall angle, and tool tip semi-spherical diameter. Furthermore, lubricant effects on the surface of the formed parts are examined by energy dispersive spectroscopy (EDS) and scanning electron microscope (SEM) images, the Alicona optical 3D measurement system, …

Mitigating Insider Threat Risks In Cyber-Physical Manufacturing Systems, Jinwoo Song

Dissertations - ALL

Cyber-Physical Manufacturing System (CPMS)—a next generation manufacturing system—seamlessly integrates digital and physical domains via the internet or computer networks. It will enable drastic improvements in production flexibility, capacity, and cost-efficiency. However, enlarged connectivity and accessibility from the integration can yield unintended security concerns. The major concern arises from cyber-physical attacks, which can cause damages to the physical domain while attacks originate in the digital domain. Especially, such attacks can be performed by insiders easily but in a more critical manner: Insider Threats.

Insiders can be defined as anyone who is or has been affiliated with a system. Insiders have knowledge …

Thermal And Mechanical Analysis Of Bombyx Mori Silk Nanofibers, Justin Busnot

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

This thesis presents a study on the thermomechanical properties of Bombyx Mori silk nanofibers. These nanofibers were obtained from silkworm cocoons which were degummed to separate the fibroin and the sericin, the two proteins that make up silk. The fibroin was then centrifuged to remove insoluble particles and stored and 4°C before the electrospinning process. A parametric study of the electrospinning process was carried out in order to identify the factors allowing to obtain optimal mechanical properties. The current as well as the flow rate applied, the diameter of the syringe, the distance separating the syringe from collector or even …

An Economical Method For Securely Disintegrating Solid-State Drives Using Blenders, Brandon J. Hopkins Phd, Kevin A. Riggle

Journal of Digital Forensics, Security and Law

Pulverizing solid-state drives (SSDs) down to particles no larger than 2 mm is required by the United States National Security Agency (NSA) to ensure the highest level of data security, but commercial disintegrators that achieve this standard are large, heavy, costly, and often difficult to access globally. Here, we present a portable, inexpensive, and accessible method of pulverizing SSDs using a household blender and other readily available materials. We verify this approach by pulverizing SSDs with a variety of household blenders for fixed periods of time and sieve the resulting powder to ensure appropriate particle size. Among the 6 household …

Early-Stage Gas Identification Using Convolutional Long Short-Term Neural Network With Sensor Array Time Series Data, Kai Zhou, Yixin Liu

Michigan Tech Publications, Part 1

Gas identification/classification through pattern recognition techniques based on gas sensor arrays often requires the equilibrium responses or the full traces of time-series data of the sensor array. Leveraging upon the diverse gas sensing kinetics behaviors measured via the sensor array, a computational intelligence-based meta-model is proposed to automatically conduct the feature extraction and subsequent gas identification using time-series data during the transitional phase before reaching equilibrium. The time-series data contains implicit temporal dependency/correlation that is worth being characterized to enhance the gas identification performance and reliability. In this context, a tailored approach so-called convolutional long short-term memory (CLSTM) neural network …

Use Of Machine Learning For Automated Convergence Of Numerical Iterative Schemes, Leonardo A. Bueno-Benitez

Doctoral Dissertations and Master's Theses

Convergence of a numerical solution scheme occurs when a sequence of increasingly refined iterative solutions approaches a value consistent with the modeled phenomenon. Approximations using iterative schemes need to satisfy convergence criteria, such as reaching a specific error tolerance or number of iterations. The schemes often bypass the criteria or prematurely converge because of oscillations that may be inherent to the solution. Using a Support Vector Machines (SVM) machine learning approach, an algorithm is designed to use the source data to train a model to predict convergence in the solution process and stop unnecessary iterations. The discretization of the Navier …

Fixed Bottom Wind Turbine Wave-Wake Interaction, Ondrej Fercak

Dissertations and Theses

The interest and benefits of offshore wind energy has also brought along legitimate design challenges for engineers. Most notably, the complex interaction between wind and turbine is further complicated by the addition of dynamic ocean waves. This dynamic coupling between wind, wave, and turbine is not fully understood. Even small improvements in wind turbine performance are welcome, so characterizing a fundamental dynamic in offshore energy is necessary to optimize design. Experimentation and simulation have been used to characterize inflow and turbine wakes and separately, wind-wave interactions. But only simulations have just begun to look at the wind, wave, and turbine …

In-Vitro And In-Silico Investigations Of Alternative Surgical Techniques For Single Ventricular Disease, Arka Das

Doctoral Dissertations and Master's Theses

Single ventricle (SV) anomalies account for one-fourth of all cases of congenital Heart disease. The conventional second and third stage i.e. Comprehensive stage II and Fontan procedure of the existing three-staged surgical approach serving as a palliative treatment for this anomaly, entails multiple complications and achieves a survival rate of 50%. Hence, to reduce the morbidity and mortality rate associated with the second and third stages of the existing palliative procedure, the novel alternative techniques called “Hybrid Comprehensive Stage II” (HCSII), and a “Self-powered Fontan circulation” have been proposed. The goal of this research is to conduct in-vitro investigations to …

Dynamic Hvac Energy Management Using Commercial Building Occupancy Metrics & Neural Networks, Krishna Chaitanya Jagadeesh Simma

Civil Engineering ETDs

With the rise of technology use in buildings, it is now possible to collect data that can be used to improve building energy consumption. One factor that has significant impact on building energy consumption is occupancy. Recent studies have shown promising results in obtaining occupancy information from existing infrastructure such as WiFi router networks. However, these existing frameworks require additional investments through software upgrades, added infrastructure, computational resources, and may raise occupant privacy concerns. Additionally, with occupant thermal comfort statistics being lower than ASHAREA specified standards, a novel approach for indoor climate control is needed. To address the limitations in …

Liner Sailing Speed Optimization Considering Wind And Waves, Zhaokun Wei, Xinlian Xie, Tiantian Bao

Journal of Marine Science and Technology–Taiwan

This paper proposes a new sailing speed optimization problem considering sea conditions such as wind and waves for a container shipping company. Since wind and waves, as exterior factors, can reduce speed, more power is employed as compensation to maintain regular service frequency and avoid delay, resulting in additional bunker consumption and higher cost. Hence, it is necessary to optimize the sailing speed according to the wind and waves. A power model was built to determine the reduced speed caused by the wind and waves for quantifying the speed reduction. On the basis of the proposed model, we developed a …

A Bilevel Mathematical Approach For The Empty Container Repositioning Proble With A Sharing And Exchanging Strategy In Liner Shipping, Dung-Ying Lin, Chieh-Ju Juan

Journal of Marine Science and Technology–Taiwan

In the maritime industry, the management of empty containers is a significant issue whose costs account for a large proportion of the total world fleet running costs. To reduce repositioning activities and increase cost effectiveness, this paper proposes a solution framework considering empty container sharing and exchanging strategies to coordinate the shipping lines in a maritime transportation network. The proposed solution framework considers an empty container matching platform company and a group of shipping lines in a given shipping network. Because of the interactive relationship between the two parties, the proposed problem is formulated as a bilevel programming problem, and …

Investigating Model Solution Correctness For Parameter Uncertainty In Both Objective Function And Constraints, Shangyao Yan, Sin-Siang Wang, Chun-Yi Wang

Journal of Marine Science and Technology–Taiwan

To resolve engineering management problems encountered in the real world, optimization models are usually formulated with some parameter assumptions. Parameter uncertainty, which may arise due to changes in the environment or human error, may thus be incorporated into the objective function and the constraints. However, to simplify the modeling, the values of these parameters are usually set or projected as deterministic values. It is no wonder that the modelling results based on these inaccurate parameters are neither correct nor reliable. Thus, it is important to examine the correctness of the model results in relation to parameter uncertainty. This study aims …

Modular Design And Implementation Of An Automatic Power Factor Regulator For Energy Savings On Fishing Vessels, Chien-Hsing Lee, Shih-Hsien Hsu, Joe-Air Jiang

Journal of Marine Science and Technology–Taiwan

This study describes the experiences of modular design and implementation of an automatic power factor regulator for improving energy efficiency on Taiwanese longline fishing vessels. The load capacities of such vessels are typically divided into three categories, depending on the gross tonnage or fish carrying capacity: less than 100 kW, from 100 kW to less than 250 kW, and larger than 250 kW. For attaining proper power factor improvement, a compensation unit with a total of 30 kVar, 60 kVar and 90 kVar was sized and assembled with capacitors of 10, 15 and 20 kVar to enable control within 12 …

Key Risk Factors Influencing Harbor Tugboat Operations For Kaohsiung Port, Wen-Jui Tseng, Ji-Feng Ding, Chia-Ming Liu, Liou-Yuan Li

Journal of Marine Science and Technology–Taiwan

The harbor tugboat operation is a very important business and process of Kaohsiung port. To ensure the safety of harbor tugboat operations and to reduce the occurrence of accidents, it is an important issue to conduct a risk assessment of tugboat operations for Kaohsiung port. Hence, the main purpose of this paper is employ the analytic hierarchy process (AHP) method to evaluate key risk factors influencing the harbor tugboat operations for Kaohsiung port. At first, a total of three evalu-ation dimensions with 14 preliminary risk factors are gener-ated from literature and interviews of tugboat captains. We then applied the steps …

Free Vibration Analysis Of A Free-Free Single-Tapered Beam Carrying Arbitrary Concentrated Elements Using Modified Mode-Superposition Method (Mmsm), Chia-Chin Wu

Journal of Marine Science and Technology–Taiwan

The literature contains scant information on the free vibration analyses of the loaded single-tapered beams (STBs) (i.e., STBs carrying concentrated elements (CEs)) Furthermore, even when such studies have been performed, they generally only consider the case of constrained (e.g., free-clamped (F-C)) beams. In other words, the problem of unconstrained (e.g., free-free (F-F)) loaded STBs has not yet to be addressed. Thus, the present study employs the modified mode-superposition method (MMSM) to investigate the free vibration characteristics of the F-F loaded STB carrying arbitrary various CEs. The investigation focuses particularly on the natural frequencies and mode shapes of the rigid-body motions …

Optimum Design Of The Underwater Discharge System Based On Surrogate Modeling, Jisang Ha, Myung-Il Roh, Seung-Ho Ham, Sung-Jun Lee

Journal of Marine Science and Technology–Taiwan

Underwater vehicles are equipped with a device for discharging projectiles, called the underwater discharge system. Because these vehicles have limited space, many studies have attempted to reduce the volume of the underwater discharge system while improving its performance. However, owing to the characteristics of the system, the occupied volume and performance conflict with each other. Therefore, minimizing the occupied volume while satisfying the required performance criteria is the most significant requirement in the design stage. To address this, an optimization problem for the underwater discharge system was mathematically formulated and solved using multi-objective genetic algorithms. Additionally, we proposed a method …

An Analysis Of Key Influencing Factors On Island Tourism Revisit Intentions – Evidence From The Matsu Islands, Chun-Chieh Wang, Hsiao-Chuan Liu, Hsuan-Shih Lee, Cheng-Chi Chung

Journal of Marine Science and Technology–Taiwan

Sightseeing and tourism not only brings economic benefits to the local community but also drive the development of related industries. In 1992, when the Matsu’s battlefield mission was dissolved, tourism became one of the key development strategies to boom the region. Although the number of visitors to Matsu Islands has risen significantly in recent years, how to increase the island’s willingness to revisit the island has been an important issue. Since local tourism has its own characteristics, island tourism marketing strategies should be different. Many previous studies have quantified the relationship between tourism area satisfaction and willingness to revisit, but …

3d Numerical Simulation Of Kuroshio-Induced Wake Near Green Island, Taiwan, Tien-Hung Hou, Jen-Yi Chang, Chia-Cheng Tsai, Tai-Wen Hsu

Journal of Marine Science and Technology–Taiwan

In this research, Kuroshio-induced vortex shedding in the lee of Green Island was numerically studied using the three-dimensional Princeton Ocean Model. The temporal and spatial characteristics of the vortex street were analyzed at different tidal levels, wind fields and water depths. The nu-merical results were validated by comparing with in-situ measurements from the Green Island tidal station, shipboard acoustic doppler current profiler (ADCP), conductivi-ty-temperature-depth (CTD) profiler, and moderate resolution imaging spectroradiometer (MODIS) satellite image datasets. Also, the three-dimensional results of velocity, temperature, and salinity fields were compared well with observational data. Furthermore, the influence depths of the wind effect and …