Mechanical Engineering Commons^™

Lignin Derived Hydrophobic Deep Eutectic Solvents As Sustainable Extractants, Yuxuan Zhang, Qi Qiao, Usman Lame Abbas, Jun Liu, Yi Zheng, Christopher Jones, Qing Shao, Jian Shi

Markey Cancer Center Faculty Publications

Solvent innovation has become a central task for improving the sustainability of chemical processes1. Deep eutectic solvents (DESs) emerge as environmentally friendly alternatives to toxic and volatile organic solvents. One appealing aspect for DESs is that they can be synthesized using naturally occurring compounds from biomass. Herein, we prepared novel hydrophobic DESs based on lignin derivatives and characterized their physicochemical properties including density, viscosity, and thermal behavior. The results showed that five lignin-derived hydrophobic DESs made from menthol, thymol, and 2,6-dimethoxyphenol were promising as green solvents due to their low viscosities and environmentally friendly constituents. To evaluate the potential application …

Selection Of Solidification Pathway In Rapid Solidification Processes, Nima Najafizadeh, Men G. Chu, Yijia Gu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Rapid Solidification Processing of Alloys Enables the Formation of Exotic Nonequilibrium Microstructures. However, the Interrelationship between the Processing Parameters and the Resulting Microstructure is Yet to Be Fully Understood. in Melt Spinning (MS) and Additive Manufacturing (AM) of Rapidly Solidified Alloys, Opposite Microstructure Development Sequences Were Observed. a Fine-To-Coarse Microstructural Transition is Typically Observed in Melt-Spun Ribbons, Whereas Melt Pools in AM Exhibit a Coarse-To-Fine Transition. in This Paper, the Microstructural Evolutions during These Two Processes Are Investigated using Phase-Field Modeling. the Variation of All Key Variables of the Solid-Liquid Interface (Temperature, Composition, and Velocity) throughout the Entire Rapid Solidification …

Utilization Of Mechanically Recycled Carbon Fibers In Vinyl Ester Composites, Khaled Alharmoodi, Amir Hussain Idrisi, Abdel Hamid Ismail Mourad, Basim Abu-Jdayil

Michigan Tech Publications, Part 1

As we enter the twenty-first century, the aviation sector is expected to thrive as flying becomes the primary mode of transportation between states or nations. With such a demand, there is a corresponding need to manufacture aircraft components. The study focused on recycling carbon fiber composites received from the STRATA company, which were cut-off/waste material generated during the manufacture of airplane components. The cut-offs were then reduced to powder form using a standard face milling machine in three sizes (90, 150, and 250 µm). After, the powder was utilized to fabricate vinyl ester composites with four weight percentages (10%, 20%, …

Me-Em Enewsbrief, December 2022, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Heat Transfer In Mini-Channel Heat Exchanger With Smooth And Pin-Fins Surfaces, Mohammed Molham Daadoua

Theses

This research aims to investigate heat transfer of single-phase and two-phase fluids in mini-channel heat exchanger with smooth and pin-fins surfaces. The main goal of the study is to develop a high-performance heat exchanger for thermal management in various processing applications. This research is carried out using computational fluid dynamics (CFD) modeling and experimentations. The proposed method is to use enhanced structured pin-fins surfaces in a mini-channel heat exchanger to improve heat transfer. The pin-fin microchannel heat exchanger is investigated using a CFD method with single-phase fluid (water, air). The experimental investigations are conducted using single-phase and two-phase fluid involving …

Origami-Inspired Sacrificial Joints For Folding Compliant Mechanisms, Todd G. Nelson, Alex Avila, Larry L. Howell, Just L. Herder, Davood Farhadi Machekposhtic

Faculty Publications

Folding is a manufacturing method which can create complex 3D geometries from flat materi- als and can be particularly useful in cost-sensitive or planar-limited fabrication applications.

This paper introduces compliant mechanisms that employ folding techniques from origami to evolve from a flat material to deployed state. We present origami-inspired sacrificial joints, joints which have mobility during assembly of the mechanism but are rigid in their final position, to create regions of high and low stiffness and the proper alignment of compliant flexures in folded mechanisms. To demonstrate the method we fold steel sheet to create some well-known and complex compliant …

Regional Stiffness Reduction Using Lamina Emergent Torsional Joints For Flexible Printed Circuit Board Design, Bryce P. Defigueiredo, Brian Dale Russell, Trent K. Zimmerman, Larry L. Howell

Faculty Publications

Flexible printed circuit boards (PCBs) make it possi- ble for engineers to design devices that use space efficiently

and can undergo changes in shape and configuration. How- ever, they also suffer from trade-offs due to non-ideal mate- rial properties. Here, a method is presented that allows en- gineers to introduce regions of flexibility in otherwise rigid

PCB substrates. This method employs geometric features to reduce local stiffness in the PCB, rather than reducing

the global stiffness by material selection. Analytical and fi- nite element models are presented to calculate the maximum

stresses caused by deflection. An example device is produced …

A Pseudo-Static Model For Dynamic Analysis On Frequency Domain Of Distributed Compliant Mechanisms, Mingxiang Ling, Larry L. Howell, June Cao, Zhou Jiang

Faculty Publications

This paper presents a pseudo-static modeling methodology for dynamic analysis of distributed compliant mechanisms to provide accurate and efficient solutions. First, a dynamic stiffness matrix of the flexible beam is deduced, which has the same definition and a similar form as the traditional static compliance/stiffness matrix but is frequency-dependent. Second, the pseudo-static modeling procedure for the dynamic analysis is implemented in a statics-similar way. Then, all the kinematic, static and dynamic performances of compliant mechanisms can be analyzed based on the pseudo- static model. The superiority of the proposed method is that when it is used for the dynamic modeling …

Kinematic/Static Model Of Complex Compliant Mechanisms With Serial-Parallel Substructures: A General Approach, Mingxiang Ling, Junyi Cao, Larry L. Howell

Faculty Publications

Kinematic and static analyses of compliant mechanisms are crucial at the early stage of design, and it can be difficult and laborsome for complex configurations with distributed compliance. In this paper, a general and concise kinematic/static modeling method of flexure-hinge-based compliant mechanisms with arbitrary serial-parallel substructures is presented to provide accurate and efficient solutions by combining the matrix displacement method with the transfer matrix method. The transition between the elemental stiffness matrix and the transfer matrix of the flexure hinge and the flexible beam is straightforward, enabling the condensation of a hybrid serial-parallel substructure into one equivalent element simple. Then, …

Normalized Coordinate Equations And Energy Method For Predicting Natural Curved-Fold Configurations, Jacob Badger, Todd G. Nelson, Rober J. Lang, Denise M. Halverson, Larry L. Howell

Faculty Publications

Of the many valid configurations that a curved fold may assume, it is of particular interest to identify natural—or lowest energy—configurations that physical models will preferentially assume. We present normalized coordinate equations—equations that relate fold surface properties

to their edge of regression—to simplify curved-fold rela- tionships. An energy method based on these normalized

coordinate equations is developed to identify natural con- figurations of general curved folds. While it has been noted

that natural configurations have nearly planar creases for curved folds, we show that non-planar behavior near the crease ends substantially reduces the energy of a fold.

Origami-Based Design Of Conceal-And-Reveal Systems, Bryce P. Defigueiredo, Kyler A. Tolman, Spencer P. Magleby, Nathan A. Pehrson, Erica Crampton, Larry L. Howell

Faculty Publications

This work introduces a type of motion termed “conceal-and-reveal” which is characterized by a state that protects a payload, a state that exposes the payload, and coupled motions between these two states. As techniques for thick, rigid origami-based engineering designs are being developed, origami is becoming increasingly more

attractive as inspiration for complex systems. This paper proposes a process for designing origami-based conceal- and-reveal systems, which can be generalized to design similar thick, rigid origami-based systems. The process

is demonstrated through the development of three conceal-and-reveal systems that present a luxury product to the consumer. The three designs also confirm …

Estimating Solar Energy Production In Urban Areas For Electric Vehicles, Shaimaa Ahmed

Theses and Dissertations

Cities have a high potential for solar energy from PVs installed on buildings' rooftops. There is an increased demand for solar energy in cities to reduce the negative effect of climate change. The thesis investigates solar energy potential in urban areas. It tries to determine how to detect and identify available rooftop areas, how to calculate suitable ones after excluding the effects of the shade, and the estimated energy generated from PVs. Geographic Information Sciences (GIS) and Remote Sensing (RS) are used in solar city planning. The goal of this research is to assess available and suitable rooftops areas using …

Sensitivity Of Puff Dynamics And Airborne Droplet Nuclei Distribution To Variations In Violent Expiration Events, M. Allahyari, K. Liu (刘凯), J. Salinas, ‪Nadim Zgheib, S. Balachandar

Mechanical Engineering Faculty Publications

We use large eddy simulations to investigate the puff and droplet dynamics from violent expiratory events such as coughs and sneezes in the first few seconds following an ejection. For each of the eleven simulations considered, over 60,000 droplets are ejected and individually tracked using the point-particle Euler–Lagrange approach. We test the sensitivity of the puff and droplet dynamics to various parameters including the ejection volume, momentum, and orientation. We also explore the effect of the mouth shape on the aforementioned dynamics by considering elliptical and circular inlet cross-sections. The results from the simulations compare favorably with a recent theoretical …

Fluid Mechanics Of Air Recycling And Filtration For Indoor Airborne Transmission, K. A. Krishnaprasad, J. S. Salinas, ‪Nadim Zgheib, S. Balachandar

Mechanical Engineering Faculty Publications

We present a statistical framework to account for effects of recycling and filtration in ventilation systems for the estimation of airborne droplet nuclei concentration in indoor spaces. We demonstrate the framework in a canonical room with a four-way cassette air-conditioning system. The flow field within the room is computed using large eddy simulations for varying values of air changes per hour, and statistical overloading is used for droplet nuclei, which are tracked with a Langevin model accounting for sub-grid turbulence. A key element is to break up the path that a virus-laden droplet nucleus can take from the time it …

Dynamic Thermal Model Development Of Direct Methanol Fuel Cell, Mohammad Biswas, Tabbi Wilberforce

Mechanical Engineering Faculty Publications and Presentations

Direct methanol fuel cell (DMFC) is fueled with liquid methanol coupled with air to produce power at reasonably lower operational conditions while resulting in by-products of carbon dioxide and water, which is more environmentally friendly. Due to the complexity associated with the performance of direct methanol fuel cell, the application of artificial neural network (ANN) can significantly predict the characteristic performance of the cells. Nevertheless, limited studies have delved into the exploration of artificial neural network in the prediction of the transient characteristics of direct methanol fuel cells. The current study however presents a detailed investigation into the prediction of …

Coaxial Jets With Disparate Viscosity: Mixing And Laminarization Characteristics, Mustafa Usta, M. R. C. Ahmad, G. Pathikonda, I. Khan, P. Gillis, D. Ranjan, C. K. Aidun

Mechanical Engineering Faculty Publications

Mixing of fluids in a coaxial jet is studied under four distinct viscosity ratios, m = 1, 10, 20 and 40, using highly resolved large-eddy simulations (LES), particle image velocimetry and planar laser-induced fluorescence. The accuracy of predictions is tested against data obtained by the simultaneous experimental measurements of velocity and concentration fields. For the highest and lowest viscosity ratios, standard RANS models with unclosed terms pertaining to viscosity variations are employed. We show that the standard Reynolds-averaged Navier-Stokes (RANS) approach with no explicit modelling for variable-viscosity terms is not applicable whereas dynamic LES models provide high-quality agreement with the …

Developing Test Methods For Compression After Lightning Strikes, Xiaodong Xu, Scott L. J. Millen, Juhyeong Lee, Gasser Abdelal, Daniel Mitchard, Michael R. Wisnom, Adrian Murphy

Mechanical and Aerospace Engineering Faculty Publications

Research into residual strength after lightning strike is increasing within the literature. However, standard test methods for measuring residual compressive strength after lightning strikes do not exist. For the first time, a systematic experimental study is undertaken to evaluate modifications necessary to standard Compression After Impact (CAI) specimen geometry and test jig design to induce specimen failure at the lightning damage region. Four laboratory generated lightning strike currents with peak amplitudes ranging from 25 to 100 kA have been studied. Test set-up modifications were made considering the scale of the lightning damage and its potential proximity to specimen edges. Specimen …

A 3d Bioprinted Hydrogel Microfluidic Device For Screening Applications, Anant Bhusal

Theses and Dissertations

The microfluidic enabled the integration of engineered miniaturized tissue models for drug screening. Conventional polydimethylsiloxane or plastic-based devices require multiple fabrication steps, which are challenging. We developed a 3D bioprinting approach to create prototypes of hydrogel-based multi-material microfluidic devices integrated with microtissue models. The approach utilizes poly(ethylene glycol) diacrylate and gelatin-methacryloyl to create microfluidic chips using multi-material bioprinting capacity with a high resolution of 15µm on x-y and 50µm on the z-axis and post-printing viability of >90%. We demonstrated easy regulation of stiffness from 24±5 kPa to 1,180±9 kPa and burst pressure from 16±1kPa to 256±19 kPa in the chip …

Static And Dynamic Analysis Of A Bistable Frequency Up-Converter Piezoelectric Energy Harvester, Mohammad Atmeh, Alwathiqbellah Ibrahim, Abdallah Ramini

Mechanical Engineering Faculty Publications and Presentations

Using energy harvesting to convert ambient vibrations efficiently to electrical energy has become a worthy concept in recent years. Nevertheless, the low frequencies of the ambient vibrations cannot be effectively converted to power using traditional harvesters. Therefore, a frequency up-conversion harvester is presented to convert the low-frequency vibrations to high-frequency vibrations utilizing magnetic coupling. The presented harvester consists of a low-frequency beam (LFB) and a high-frequency beam (HFB) with identical tip magnets facing each other at the same polarity. The HFB, fully covered by a piezoelectric strip, is utilized for voltage generation. The dynamic behavior of the system and the …

Electric Field-Assisted Nanofiltration For Pfoa Removal With Exceptional Flux, Selectivity, And Destruction, Yangyuan Ji, Youn Jeong Choi, Yuhang Fang, Hoang Son Pham, Alliyan Tan Nou, Linda S. Lee, Junfeng Niu, David M. Warsinger

School of Mechanical Engineering Faculty Publications

Per- and polyfluoroalkyl substances (PFAS) pose significant environmental and human health risks and thus require solutions for their removal and destruction. However, PFAS cannot be destroyed by widely used removal processes like nanofiltration (NF). A few scarcely implemented advanced oxidation processes can degrade PFAS. In this study, we apply an electric field to a membrane system by placing a nanofiltration membrane between reactive electrodes in a crossflow configuration. The performance of perfluorooctanoic acid (PFOA) rejection, water flux, and energy consumption were evaluated. The reactive and robust SnO2–Sb porous anode was created via a sintering and sol–gel process. The characterization and …

An Alternate Dimensionless Form Of The Linearized Rigid-Body Aircraft Equations Of Motion With Emphasis On Dynamic Parameters, Douglas F. Hunsaker, Benjamin C. Moulton

Mechanical and Aerospace Engineering Student Publications and Presentations

The equations of motion for an aircraft can be linearized about a reference condition within the assumptions of small disturbances and linear aerodynamics. The resulting system of equations is typically solved to obtain the eigenvalues and eigenvectors that describe the small disturbance motion of the aircraft. Results from such an analysis are often used to predict the rigid-body dynamic modes of the aircraft and associated handling qualities. This process is typically carried out in dimensional form in most text books, or in nondimensional form using dimensionless parameters rooted in aerodynamic theory. Here we apply Buckingham’s Pi theorem to obtain nondimensional …

Interfaces In Dynamic Brittle Fracture Of Pmma: A Peridynamic Analysis, Longzhen Wang, Javad Mehrmashhadi, Florin Bobaru

Department of Mechanical and Materials Engineering: Faculty Publications

Recent experiments in bonded PMMA layers have shown dramatic changes in dynamic crack growth characteristics depending on the interface location and toughness. In this paper we present a peridynamic (PD) analysis of this phenomenon and determine three elements that are essential in a model reproducing the observed fracture behavior: (1) softening near the crack tip to account for changes in PMMA due to heat-generation induced by the high strain rates reached around the crack tip in dynamic fracture; (2) independent extension (mode I) and shear (mode II) modes of fracture; (3) a two-parameter fracture model, which matches both strength and …

Comparing The Performance Of Different Machine Learning Models In The Evaluation Of Solder Joint Fatigue Life Under Thermal Cycling, Jason Scott Ross

Dissertations and Theses

Predicting the reliability of board-level solder joints is a challenging process for the designer because the fatigue life of solder is influenced by a large variety of design parameters and many nonlinear, coupled phenomena. Machine learning has shown promise as a way of predicting the fatigue life of board-level solder joints. In the present work, the performance of various machine learning models to predict the fatigue life of board-level solder joints is discussed. Experimental data from many different solder joint thermal fatigue tests are used to train the different machine learning models. A web-based database for storing, sharing, and uploading …

Effect Of Blank Moisture Content On Forming Behaviour And Mechanical Properties Of Paperboard Tray Packages, Arvo Niini, Lena Berthold, Tobias Müller, Panu Tanninen, Jens-Peter Majschak, Juha Varis, Ville Leminen

Journal of Applied Packaging Research

Tray blanks were moisturised to study the effect of different blank moisture content levels on forming behaviour and mechanical properties of paperboard tray packages. The blank moisturisation was done by spraying water to the blanks before their three-dimensional (3D) forming. The trays were 3D formed by press forming or deep drawing. Visual quality and punch force values were used as indicators to evaluate the forming behaviour of the trays. The mechanical properties of the trays were investigated with compression, torsion, and storing tests. A high blank moisture content reduced the punch force, and the elevated blank moisture was connected to …

Demonstrating Non-Isothermal Vacuum Membrane Air Dehumidification For Efficient Next-Generation Air Conditioning, Andrew J. Fix, Shivam Gupta, James E. Braun, David M. Warsinger

School of Mechanical Engineering Faculty Publications

Vacuum membrane air dehumidification has gained significant interest in recent years as a highly efficient means of air dehumidification. Prior theoretical modeling work by the authors 1 introduced the Active Membrane Energy Exchanger (AMX) concept, which combines active heat exchange and vacuum membrane dehumidification into one non-isothermal system, and found that it could outperform other air conditioning technologies under many conditions. However, no experimental literature exists on combining active heat exchangers and vacuum membrane dehumidification. The goal of the present study is to evaluate the dehumidification (mass transfer) performance of the AMX concept relative to isothermal membrane dehumidification through three …

Freespan Analysis For Subsea Pipeline Integrity Management Strategy, Nurul Hadi, Muhammad Helmi, Edo Cathaputra, Dedi Priadi, Donanta Dhaneswara

Journal of Materials Exploration and Findings

Abstract. Over a rough seabed or on seabed subject to scour, freespans can occur when contact between a subsea pipeline and the seabed is lost over an acceptable distance. When this exceeds the allowable freespan length, design stresses can be exceeded, and a vortex induced vibration (VIV) response can be initiated, resulting in the risk of fatigue failure. If this is not predicted and controlled properly, it will affect pipeline integrity, leading to expensive rectification and intervention work. Freespan analysis consisted primarily of a screening check in which the as-found freespans from Remotely Operated Vehicle (ROV) or multibeam Side …

Effect Of Austenization And Repeated Quenching On The Microstructures And Mechanical Properties Of Wear-Resistant Steel, Yanuar Nugraha, Myrna Ariati Mochtar

Journal of Materials Exploration and Findings

This study was focused on determining the effect of repeated austenitization and quenching on mechanical properties and microstructure. The experiment was carried out in a rolled quencher facility with a heat treatment process of one to two times, with parameters of an austenizing temperature of 9500C and quenching at a temperature of 8500C with pressurized water media. Testing of specimens, including microstructure observations and hardness testing. The repeated heat treatment process showed an increase in hardness of 0.79% on one-time repeated heat treatment and 1.65% on two repeated heat treatments. This occurs due to the presence accompanied by refinement of …

Locally Resonant Metasurface For Low-Frequency Transmissive Underwater Acoustic Waves, Zhong Chen, Shenghong Guan, Qiang Xie, Zheng Li, Zhongmei Gao, Mehrdad Negahban

Department of Mechanical and Materials Engineering: Faculty Publications

Introduction: Acoustic metasurfaces for underwater wave manipulation have great potential use, but the strong solid-fluid interaction caused by impedance closeness between the structure and water brings design difficulty, especially in the low-frequency range.

Methods: Here a locally resonant metasurface for transmissive underwater acoustic waves is proposed using finite element method for which each metasurface unit consists of one channel and three subunits. Each subunit has one plate and two rubber spacers to form a resonator. By changing the height ratio of the plate over the subunit, arbitrary phase shifts within the full 2π coverage can be obtained at …

Using Dielectric Scatters To Selectively Excite Embedded Eigenstates In Cavity Resonators, Olugbenga Joshua Gbidi

Theses and Dissertations

Bound states in the continuum (BICs) are waves that remain in the continuous spectrum of radiating waves that carry energy, however, still localized within the spectrum. BICs, also embedded eigenmodes, exhibit high quality factors that have been observed in optical and acoustic waveguides, photonic structures, and other material systems. Presently, there are limited means to select these BICs in terms of the quality factor and their excitation. In this work, we show that a different type of BIC, Quasi-BICs (Q-BICs), in open resonators can have their quality attuned by introducing embedded scatters. Using microwave cavities and dielectric scatters as an …

Probing The Influence Of Surface Chemical Functionalization On Graphene Nanoplatelets-Epoxy Interfacial Shear Strength Using Molecular Dynamics, Hashim Al Mahmud, Sagar Patil, Matthew Radue, Gregory Odegard

Michigan Tech Publications, Part 1

In this work, a characterization study of the interfacial interaction between different types of graphene nanoplatelets and an epoxy matrix is computationally performed. To quantify the discrete mutual graphene–epoxy “interfacial interaction energy” (IIE) within the nanocomposite, molecular dynamics simulations with a reactive force field are performed on a localized model of the suggested nanocomposite. Pull-out molecular dynamics simulations are also performed to predict the interfacial shear strength between the two constituents. The results indicate a significant increase in interfacial adhesion of functionalized nanoplatelets with the hosting epoxy matrix relative to virgin graphene nanoplatelets. The obtained results also demonstrate a dramatic …