Mechanical Engineering Commons^™

Research On An Improved Cotton Cleaner Unit, Muzaffar Djurayev, Sherqul Hakimov, Ilhom Abbazov, Rashid Kaldybaev

Technical science and innovation

This article analyzes the results of changes to the working parts of a cotton cleaning unit from small and large impurities. It is known that the UXK installation uses continuous cleaning technology, that is, the cotton entering the purifier is cleaned in all its cleaning sections and then transferred to another process. In these sections, pieces of cotton wool from the separated waste are regenerated in a separate drum. Existing purifier suppliers use a manually operated mechanical system to monitor its performance. These factors do not make it possible to control the cleaning process when the quality indicators of cotton …

Polymerizing Actin Regulates Myosin-Independent Mechanosensing By Modulating Actin Elasticity And Flow Fluctuation, Nikhil Mittal, Etienne Michels, Kathleen Pakenas, Shaina P. Royer-Weeden, Sangyoon J. Han

Michigan Tech Publications

The stiffness of the extracellular matrix induces differential tension within integrin-based adhesions. However, it has been unclear if the stiffness-dependent differential tension is induced solely by myosin activity. Here, we report that in the absence of myosin contractility, 3T3 fibroblasts still transmit stiffness-dependent differential levels of traction. This myosin-independent differential traction is regulated by polymerizing actin assisted by actin nucleators Arp2/3 and formin where formin has stronger contribution than Arp2/3. Interestingly, we report a four-fold reduction in traction of cells when both Arp2/3 and myosin were inhibited, compared to cells with only myosin inhibition, while there was only a slight …

Myosin-Independent Stiffness Sensing By Fibroblasts Is Regulated By The Viscoelasticity Of Flowing Actin, Nikhil Mittal, Etienne B. Michels, Andrew E. Massey, Yunxiu Qiu, Shaina P. Royer-Weeden, Bryan R. Smith, Alexander X. Cartagena-Rivera, Sangyoon J. Han

Michigan Tech Publications

The stiffness of the extracellular matrix induces differential tension within integrin-based adhesions, triggering differential mechanoresponses. However, it has been unclear if the stiffness-dependent differential tension is induced solely by myosin activity. Here, we report that in the absence of myosin contractility, 3T3 fibroblasts still transmit stiffness-dependent differential levels of traction. This myosin-independent differential traction is regulated by polymerizing actin assisted by actin nucleators Arp2/3 and formin where formin has a stronger contribution than Arp2/3 to both traction and actin flow. Intriguingly, despite only slight changes in F-actin flow speed observed in cells with the combined inhibition of Arp2/3 and myosin …

Optimum Design Of Metallic And Plastic Cylindrical Gears Using Naturally-Inspired Algorithms: A Review, Marah Elsiedy, Hesham Hegazi, Ahmed Elkassas, Abdelhameed Zayed

Journal of Engineering Research

Abstract- Nowadays, several machinery and vehicles utilize mechanical elements which transmit power ranges from low, middle, and high levels depending on the type of equipment needed. Gears are the most influential design elements on any process during the running of a specific application, moreover engineers tried to obtain the optimality of a gear design which is a more compact, reliable- long service with simply operating features by following a systematic calculation of the mathematical model from standards and handbooks, however this process doesn't give the optimal design of the gears. Optimization techniques have been added to the design process for …

Enhancing The Performance Of Conventional Solar Still Using The Nano-Doped Paint (Ndp) Coating, Hagar Alm-Eldin Bastawissi Prof.Dr, Nermin Elgendy Engineer, Ayman R. El-Tohamy

Journal of Engineering Research

Nations are throughout the entire globe continuously confronting the problem of potable water shortage. Recently, it has been thought that using solar energy to desalinate brackish water offers a practical answer to the world's water crises. The output of these stills, is meager, and academics haven't done much to boost it in any way. Solar distillers have been proposed as an efficient method to produce potable water. In recent years, saltwater has produced drinking water by various ways. The efficiency of a solar distiller is significantly influenced by various factors, most important factor of them is the absorber surface. In …

Numerical Study Of The Effect Of Long Shroud Diffuser With And Without Plate Obstacle On The Performance Of Savonius Wind Turbine, Alsaied Khalil Mahmoud, Mohamed Mahgoub Bassuoni, Mohamed Fawzy Obiaa, Ahmed Mostafa Khaira

Journal of Engineering Research

This study presents the three-dimensional (3-D) numerical analysis of the influence of the plate obstacle installed at the entrance of the long flanged diffuser on the simple Savonius rotor performance by ANSYS 2022 R1. In the beginning, the 3-D numerical model is validated using the sst k-ω turbulence model with the previous published experimental results at the same conditions, and they are in good agreement with each other. The numerical results indicate the remarkable enhancement of the rotor performance at a tip speed ratio of 0 to 0.7 by using a flanged diffuser with a plate obstacle. The shrouded diffuser …

The Influence Of Using Hho With Sunflower And Soybean Oil Biodiesel/Diesel Blend On Pcci Engine Characteristics, Mai H. Aboubakr, Medhat Elkelawy Prof. Dr., Hagar Alm-Eldin Bastawissi Prof. Dr., Ayman R. El-Tohamy Dr.

Journal of Engineering Research

This research studies the influence of various blends of sunflower and soybean oil biodiesel with diesel fuel on premixed charge compression engine characteristics, including performance and exhaust emissions, and also investigates the impact caused by oxyhydrogen gas addition on them. The experiments were carried out on a single cylinder PCCI engine which utilizing eight blends of the fuels. Conventional diesel, B20D80, B40D60, B60D40, B80D20, B40D60 + 5 LPM HHO, B40D60 + 10 LPM HHO, and B40D60 + 15 LPM HHO have been used to obtain performance and exhaust emissions characteristics. The hydrogen peroxide additive has introduced into the engine manifold …

Performance Of Photocatalytic Oxidizing Air Cleaners In Different Experimental Setups – A Review, Giovanni Cerrato, Nelson Fumo

Mechanical Engineering Faculty Publications and Presentations

Photocatalytic oxidizing (PCO) air cleaners are offered for the abatement of gaseous pollutants (i.e., Volatile Organic Compounds or VOCs). However, due to a lack of testing standards, the overall characterization of the technology's effectiveness has been met with conflicting results. Different studies use varying experimental setups, test conditions, and different PCO air cleaner designs. According to the literature, the majority of testing has been in controlled laboratory setups with favorable conditions. As PCO air cleaner testing is scaled up to more realistic environments and conditions, the PCO removal efficiency tends to significantly decrease. The differences in removal efficiency can be …

Stick-Fixed Maneuver Points In Roll, Pitch, And Yaw And Associated Handling Qualities, Benjamin C. Moulton, Troy A. Abraham, Douglas F. Hunsaker

Mechanical and Aerospace Engineering Student Publications and Presentations

The stick-fixed pitch maneuver point is an important measure of aircraft longitudinal dynamic response and handling quality characteristics, and includes effects of both aerodynamic and inertia properties of the aircraft about the pitch axis. In the present work, the existence of stick-fixed roll and yaw maneuver points is demonstrated, which are determined from the lateral forces, moments, and inertial properties of the aircraft. These stick-fixed roll and yaw maneuver points are directly related to the predicted lateral handling qualities. Example results are included for several aircraft that demonstrate the importance of this parameter when predicting the dynamic response of the …

Engineering Neurotoxin-Functionalized Exosomes For Targeted Delivery To The Peripheral Nervous System, Mena Asha Krishnan, Olawale A. Alimi, Tianshu Pan, Mitchell Kuss, Zeljka Korade, Guoku Hu, Bo Liu, Bin Duan

Department of Mechanical and Materials Engineering: Faculty Publications

The administration of therapeutics to peripheral nerve tissue is challenging due to the complexities of peripheral neuroanatomy and the limitations imposed by the blood–nerve barrier (BNB). Therefore, there is a pressing need to enhance delivery effectiveness and implement targeted delivery methods. Recently, erythrocyte-derived exosomes (Exos) have gained widespread attention as biocompatible vehicles for therapeutics in clinical applications. However, engineering targeted Exos for the peripheral nervous system (PNS) is still challenging. This study aims to develop a targeted Exo delivery system specifically designed for presynaptic terminals of peripheral nerve tissue. The clostridium neurotoxin, tetanus toxin-C fragment (TTC), was tethered to the …

Yap Mechanotransduction Under Cyclic Mechanical Stretch Loading For Mesenchymal Stem Cell Osteogenesis Is Regulated By Rock, Eunju Kim, Brandon D. Riehl, Tasneem Bouzid, Ruiguo Yang, Bin Duan, Henry J. Donahue, Jung Yul Lim

Department of Mechanical and Materials Engineering: Faculty Publications

While yes-associated protein (YAP) is now recognized as a potent mechanosensitive transcriptional regulator to affect cell growth and differentiation including the osteogenic transcription of mesenchymal stem cells (MSCs), most studies have reported the YAP mechanosensing of static mechanophysical cues such as substrate stiffness. We tested MSC response to dynamic loading, i.e., cyclic mechanical stretching, and assessed YAP mechanosensing and resultant MSC osteogenesis. We showed that cyclic stretching at 10% strain and 1 Hz frequency triggered YAP nuclear import in MSCs. YAP phosphorylation at S127 and S397, which is required for YAP cytoplasmic retention, was suppressed by cyclic stretch. We also …

Improvement Of Convective Drying Equipment, A Ponasenko, Jasur Safarov, Shaxnoza Sultanova

Technical science and innovation

Drying of agricultural raw materials is an energy-consuming but integral process. Therefore, increasing the efficiency of drying and improving the quality indicators of dried material at minimum material and energy costs is relevant for producers of agricultural products. By present time numerous researches on improvement of constructions and processes of work of dryers providing satisfactory parameters of energy saving have been carried out. In some scientific materials it is shown that the use of generative gas and straw as fuel allows to reduce energy costs for the drying process in the fluidised bed dryer by 10-30%, the quality of seeds …

Existing Methods For Monitoring Power Autotransformers, Nurali Berdiyorovich Pyrmatov, Dilafruz Rustamjon Qizi Abdullabekova

Technical science and innovation

autotransformers, methods, diagnostics, efficiency, monitoring.Particular attention is given to analyzing the gas composition of transformer oil, which is a sensitive indicator of various defects such as thermal breakdown and heating. In addition, methods based on the measurement of external magnetic field strength are discussed. This technique provides a unique opportunity to detect magnetic anomalies associated with possible defects in the structural components of the transformer. The article emphasizes that successful monitoring requires an integrated approach, combining different techniques. The authors analyze the advantages and limitations of each method and offer practical recommendations for integrating these methods into maintenance systems. In …

Mathematical Modeling Of Fruit Drying And System Analysis Of The Process (On The Example Of Persimmon), Gani Dadayev, Jasur Safarov, Shakhnoza Sultanova, Qobiljon Muxiddinov

Technical science and innovation

Vegetable raw materials, as an object of drying, are characterized by a large amount of water and a low content of dry substances. Vegetable raw materials have a capillary-porous structure. Food products contain both bound and free moisture at the same time. The removal of moisture from the material during drying depends on the total moisture content and the form of connection of moisture with the material. Adsorption and osmotic - bound moisture is retained at the interface of colloidal particles with the environment. Food products contain both bound and free moisture at the same time. The quantitative ratio between …

Capacitive Electrode Based Moisture Measurement Converter Errors And How To Eliminate Them, Hamdam Jabborov, Temurbek Rashidov

Technical science and innovation

The article discusses the errors associated with the moisture measuring transducer that is based on the cylindrical electrode, along with their sources and calculation formulas for error elimination. The initial capacitance of the capacitive electrode humidity converter is dependent on its geometric parameters, such as the radii of the electrodes and their length. Accurate calculation of these geometric parameters enables the reduction of regular measurement errors in the input and switching circuit of the moisture converter to a minimum value, resulting in a significant increase in the informativeness and accuracy of the output signal. Consequently, some sources of measurement errors …

Influence Of Foil Stamping Parameters On Image Quality, Khalima Abishevna Babakhanova, Mukhlisa Ergashevna Khasanova, Aziz Azimjonovich Soadatov, Nigora Junaydullaevna Sadriddinova

Technical science and innovation

The paper evaluates the influence of technological process parameters, namely die temperature and pressure force, on the quality of foil stamping, which is one of the types of finishing having a wide range of applications due to giving unique decorative and protective elements to printed products. When evaluating the influence of process parameters on the linearity and coverability of the image, it was found that the pressure force has less influence on the result than the temperature. According to the data of the study, it can be concluded that the maximum percentage of completeness of covering is achieved at a …

Enhancing Bridge Resilience And Overheight Vehicle Mitigation Through Innovative Sacrificial Cushion Systems, Aly Mousaad Aly, Marc Hoffmann

Faculty Publications

Transportation departments have made significant strides in addressing the challenges posed by the increasing weights of trucks on bridges. While there is a growing awareness of overheight vehicle collisions with bridges, implementing effective countermeasures remains limited. The susceptibility of bridges to damage from such collisions is on the rise, further exacerbated by unpredictable lateral impact forces. This study employs nonlinear impact analysis to assess the response of an unprotected vehicle-girder model, yielding realistic deformation outcomes comparable to observed impacts on the US-61 bridge. Predictions for a truck traveling at 112.65 km/h indicate deformations of 0.229 m, 0.161 m, and 0.271 …

Comparison Of Empirical And Analytical Eigenfunctions As Bases For Reduced Order Methods In Heat Transfer, Jakob G. Bates, Matthew R. Jones, Christopher R. Dillon, John Tencer

Student Works

Reduced order methods using spectral representations show promise in facilitating and accelerating heat transfer analyses. This paper proposes a taxonomy for reduced order methods, classifying a method as reduced order compression, modelling, or analysis. The performance of bases formed with analytical and empirical eigenfunctions are compared for representative reduced order tasks. The Akaike Information Criterion is applied in a novel way to compare the performance of these bases. The present study finds that both bases are parsimonious for reduced order compression tasks. Empirical eigenfunctions are more robust to for reduced order modelling with variations in modelling parameters such as thermal …

Commentary: A Patient-Specific Lower Extremity Biomechanical Analysis Of A Knee Orthotic During A Deep Squat Movement, Christine Dailey Walck

Publications

The recent study by Walck et al., titled “A Patient-Specific Lower Extremity Biomechanical Analysis of a Knee Orthotic during a Deep Squat Movement,” provides a novel insight into the biomechanical impacts of knee orthotics, particularly the non-linear spring-loaded (NLSL) knee joint orthosis (KJO)1 . This commentary aims to delve into the implications, interpretations, and evaluations of the findings, contextualizing them within the broader discourse on knee orthotics.

Redesign Of Leg Assembly And Implementation Of Reinforcement Learning For A Multi-Purpose Rehabilitation Robotic Device (Roborehab), Jacob Anthony, Chung-Hyun Goh, Alireza Yazdanshenas, Yong Tai Wang

Mechanical Engineering Faculty Publications and Presentations

Patients who are suffering from neuromuscular disorders or injuries that impair motor control need to undergo rehabilitation to regain mobility. Gait training is commonly prescribed to patients to regain muscle memory. Automated-walking training devices were created to aid this process; while these devices establish accurate ankle-path trajectories, the knee and hip movements are inaccurate. In this work, a redesign of the leg assembly in a multi-purpose rehabilitation robotic device (RoboREHAB) was explored to improve hip- and knee-movement accuracy by adding an extra link and rollers to the assembly. Motion analysis was employed to test feasibility, reinforcement learning was utilized to …

Experimental Environmental Profiles And Sloshing Dynamics Aboard Zero-G Aircraft, Pedro J. Llanos, Sathya Gangadharan, Kevin Crosby

Publications

This study presents the results of a parabolic flight experiment to study the sloshing dynamics of the magneto-active propellant management device experiment. This device utilizes a magnetoactive membrane and magnets located external to the tank to effectively damp the liquid free surface motion. This research work establishes a benchmark with sloshing analytical formulation and sensor calibration methods that can be used to characterize future research parabolic flights while providing important environmental profiles measured during flight, such as accelerations, pitch angle, velocity, temperature, total volatile content, carbon dioxide, relative humidity, magnetic field, and radiation. Correlation between these flight variables and the …

Sustainable Phone Housing, Jonah Milnor

All Undergraduate Projects

Most commercially available smartphones posed a challenge to consumers due to the use of adhesives, which not only served to seal out dust and water but also hindered repairability and hardware replacement. Drawing inspiration from successful smartwatch designs employing gaskets for water resistance, this project aimed to adapt such design principles to the smartphone form factor.

Utilizing SolidWorks for design and subsequent 3D printing and CNC machining for prototyping, 3D models of a smartphone housing were crafted. The objective was to attain a level of water and dust resistance equivalent to that of model smartphones, utilizing sealing methods equivalent to …

Rc Baja Car Suspension & Steering, Jarvis Hudnall

All Undergraduate Projects

Students at Central Washington University were faced with a challenge to engineer an RC Baja Car with a focus between drivetrain and chassis or suspension and steering for a competition. The different foci were split between two team members and the engineering for this report is focused on steering and suspension.

The suspension and steering components underwent the process of developing calculations for all individual parts for design. The design process included using CAD software to provide a 3D model for each individual part. To save time, 3D modeling software helped find fitment issues before the RC Car was manufactured …

Nasa Student Launch Payload Kinetic Energy Absorption, Harrison X. Fishburn

All Undergraduate Projects

The challenge given by NASA was to design and build a reusable payload capable of a human survivable landing, without the use of a parachute or streamer.

The method chosen to accomplish this was a large spring to extend and mitigate impact forces over a few seconds. The device was attached to the lower end of the payload to act as a secondary force reducer, with the primary device being the gyrocopter assembly built by Brycen. Two 6061 aluminum rods, attached together with a spring, act as the main structure of the payload, connecting the spring assembly, the capsule, the …

Me-Em 2022-23 Annual Report, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering Annual Reports

Table of Contents

• Research Updates
• Curriculum and Instruction
• Facilities
• New Faculty
• Research, Machine Learning
• Research, Ana Dyreson
• In Memoriam
• Student Success
• Alumni Profile and Activity
• Graduates
• Faculty Awards and Honors
• Patents and Publications
• Donors
• Grants and Contracts

Balsa Bridge, Caleb T. Lovett

All Undergraduate Projects

The problem presented throughout this report was to create a small-scale bridge made entirely out of balsa wood and glue, that could withstand substantial force, as well as perform a lifting/lowering cycle. Other requirements associated with the bridge were properties of weight, deflection, size, and shape. This problem presented a challenge that tested the mathematical side of engineering, being strongly reliant on statics, mechanics of materials, and mechanical design analyses.

To approach this problem, the first step was to complete in depth calculations of the chosen design. With this done, manufacturing and assembly was able to be completed. With a …

Rc Baja Drivetrain And Chassis, Beni Ntanda

All Undergraduate Projects

The RC vehicle comprises 4 crucial subsystems: the chassis, drivetrain, suspension, and steering. This paper will cover the chassis and drivetrain, and my partner Noah Stevens will cover the suspension and steering. The chassis serves as a robust framework housing all vehicle components, while the drivetrain transmits power from the motor to the wheels, propelling the vehicle. An efficient drivetrain typically sacrifices speed for enhanced torque, aiming to minimize energy losses. Meanwhile, an ideal chassis features minimal deflection and user-friendly mounting points. This RC vehicle participated in the CWU RC Baja competition, aiming to rank among the top contenders.

The …

Rc Baja Steering And Suspension, Chayce Williams

All Undergraduate Projects

The engineering objective of this project are designing, manufacturing, and testing the most efficient and strongest possible RC Baja Steering and Suspension system that the engineer could produce with the provided or acquired equipment, and materials.

This was all done successfully over the school year. During the Fall quarter, the RC car was undergoing designing, and in these design processes, mechanics of materials, statics, and dynamics, were used to come up with the most adequate materials and design. Computer aided designed (CAD) models were then created to get a RC Baja CAD assembly. Winter Quarter of the school year was …

Articulating Balsa Wood Bridge, Kyle Barayuga

All Undergraduate Projects

Bridges have been used worldwide to allow passage between untraversable terrain. These bridges are built according to their terrain and environment, while also withstanding the forces of objects going across them. This project explores building a bridge under specific design restrictions to be able to simulate objects traversing across and under it. The device consists of a bridge, utilizing a Pratt truss design, and an articulation tower which are mechanically linked using a hinge. The articulation tower allows the bridge to be raised and lowered, simulating an object to be passed under. Raising and lowering the bridge consists of using …

Rc Baja: Steering And Suspension, Rogelio Arroyos, Roberto Vieyra

All Undergraduate Projects

Students attending Central Washington University teamed up to manufacture an RC car to compete against peers in the RC Baja competition events as a senior project. The project was split between the two individuals, Rogelio was responsible for the steering and suspension, while Roberto was responsible for the chassis and drivetrain. The team collaborated to brainstorm ideas that would fit the requirements applied.

The RC was built with 3D printed parts and designed using engineering methods such as mechanics of materials, dynamics, and statics to successfully compete in the BAJA events and meet requirements. Before it was ready for competition, …