Mechanical Engineering Commons^™

A Study On The Fluorescent Properties Of Nanoapatite Particles Under Externally Applied Magnetic Fields, Heidi Reid

TECHxpo

Hydroxyapatite is a naturally occurring mineral found in human bones and teeth. Its chemical formula is: Ca₁₀(PO₄)₆(OH)₂. In this project hydroxyapatite nanoparticles were doped with iron or europium to give the particles magnetic or fluorescent properties, respectively. The magnetic and fluorescent responses of these particles under externally applied magnetic fields has not yet been fully characterized.

Development Of Nhtsa’S Side Impact Test Procedure For Child Restraint Systems Using A Deceleration Sled : Part 2, Janet Brelin-Fornari, Sheryl Janca

Mechanical Engineering Grants

This report presents the results of the continued research and development of child seat side impact tests using the deceleration sled at Kettering University’s Crash Safety Center. The objective of this test series was to gain further insight into the sensitivity of the side impact test fixture response. Test variations included speed of impact, weight of the fixture, and impact characteristics. Additionally, 20 child restraint system (CRS) specific tests were conducted using a fixed set of test parameters.

Phase Transformation In Monolayer Molybdenum Disulphide With And Without Defects Under Tension Predicted By Atomistic Simulations, Khanh Quoc Dang

Graduate Theses and Dissertations

In addition to its use as a solid lubricant, molybdenum disulphide (MoS2) has gained recent attention as a possible substitute for silicon as it is increasingly difficult to keep shrinking down electronic devices made of silicon, the conventional electronic material. When thinned down to atomic thickness, monolayer MoS2 possesses very unique and promising electronic and electrical properties. Unlike electronic and electrical properties, knowledge of the mechanical properties and role of structural defects on these properties of monolayer MoS2 is unexplored. For this thesis, the two main objectives are (1) to gain insight about the failure mechanism of monolayer MoS2 by …

Redesigning The Walker: A More Durable & Dignified Device, Gianna M. Curcio

Renée Crown University Honors Thesis Projects - All

Aging and Rehabilitation Engineering is a prominent field with ample room for development of and improvement upon existing options. Surveying city sidewalks, family gatherings, hospital waiting rooms it becomes apparent that the need for mobility aids is abundant. My proposal for Capstone is to redesign the walker from both my mechanical engineering and sculptural perspectives. A walker is meant to improve the quality of life for those who are unable to walk unassisted, but should not come at the cost of the user’s dignity. The way we carry ourselves says a lot about us (i.e. character, will, and level of …

Ultrathin Ptfe Coating For Hypodermic Needles Enabled By Mussel-Inspired Pda Adhesive Layer, Spencer A. Foust

Mechanical Engineering Undergraduate Honors Theses

Polytetrafluoroethylene (PTFE) is a synthetic fluoropolymer of tetrafluoroethylene, commonly known by its brand name Teflon®, which has many desirable properties such as a low coefficient of friction, high temperature resistance, anti-microbial properties, hydrophobicity, biocompatibility, and chemical resistance. One of the major challenges caused by the non-stick property of PTFE is its poor adhesion to substrates: PTFE coatings can be easily detached from surfaces under frictional forces and shear. The molecule polydopamine (PDA) was discovered as the key protein for adhesion between polytetrafluoroethylene and substrates of many materials, including steel, and thus has been used as a unique approach for coatings. …

Personal Vacuum Assisted Climber, Jacob Monroe Whittle

Undergraduate Honors Capstone Projects

The Personal Vacuum Assisted Climber (PVAC) system built in 2012 by the Ascending Aggies at Utah State University which was designed using vacuum motors to provide suction to pads to allow the user to climb various surfaces, needs to be further developed before being fully marketable. The current system does not have a user-friendly interface and is very loud (approx. 90 dB). These issues were addressed to answer the following question: how can the current PV AC system be optimized to decrease noise and produce a user friendly interface while maintaining current run time? To obtain the sound reduction desired …

Advancements In Alternative Energy Applications For Space Conditioning., Brian S. Robinson

Electronic Theses and Dissertations

This dissertation documents advancements made in passive, renewable energy applications for building space conditioning (heating and cooling). Since, for most climates across the US, space heating requires a much larger annual energy demand than space cooling, the majority of this dissertation is focused on the heating season. The dissertation is divided into five chapters, primarily covering computer simulations and experimental studies pertaining to specific space conditioning technologies. Chapter One discusses the significance of supplanting fossil fuel based energy production with clean, renewable sources, and provides further detail on the organization of this dissertation. Chapter Two provides background on the heat …

Development And Evaluation Of A Calibration Free Exhaustive Coulometric Detection System For Remote Sensing., Thomas James Roussel

Electronic Theses and Dissertations

Most quantitative analytical measurement techniques require calibration to correlate signal with the quantity of analyte. The purpose of this study was to employ exhaustive coulometry, an implementation of coulometric analysis in a stopped-flow, fixed-volume, thin-layer cell, to attain calibration-free measurements that would directly benefit intervention-free analysis systems designed for remote deployment. This technique capitalizes on the short diffusion lengths (< 100 µm) to dramatically reduce the time for analysis (< 30 sec). For this work, a thin-layer fluidic cell was designed in software, fabricated via CNC machining, and evaluated using Ferri/Ferrocyanide {Fe(CN)63-/4-} as a model analyte. The 2 µL fixed volume incorporated an oval, 8mm by 4 mm, thin-film gold electrode sensor with an integrated Ag|AgCl pseudo-reference electrode. The flow cell area matched the shape of the sensor, with a volume set by the thickness of a laser-cut silicone rubber gasket (~80 µm). A semi-permeable membrane isolated the working electrode and counter electrode chambers to prevent analyte diffusion. A miniaturized custom potentiostat was designed and built to measure reaction currents ranging from 10 mA to 0.1 nA. Software was developed to perform step voltammetry as well as cyclic voltammetry analysis for verifying electrode condition and optimal redox potential levels. Experimentally determined oxidation/reduction potentials of -100 mV and 400 mV, respectively, were applied to the working electrode for sample concentrations ranging from 50 µM to 10,000 µM. The current generated during the reactions was recorded and the total charge captured at each concentration was obtained by integrating the amperograms. When compared to the expected charge for a 2 µL sample, the total charge vs. concentration plots displayed a near perfect linearity over the full concentration range, and the expected charge (100 % converted) was reached within 20 seconds. The reaction currents ideally should have decayed to background levels, but exhibited constant offset values slightly larger than the background signal, a phenomenon assumed to be lingering residual flow from sample injection. After adding rigid tubing and external valves, the thin-layer cell was shown to remain within 6% of the theoretical charge after 200 seconds. Continued development of this system will offer the possibility of remote, calibration-free determinations of real-world analytes such mercury and lead.

Process Capability In A Computer Integrated Manufacturing Cell, Andrew Austin

Masters Theses & Specialist Projects

With the rise of automation in traditional manufacturing processes, more companies are beginning to integrate computer integrated manufacturing (CIM) cells on their production floors. Through CIM cell integration, companies have the ability to reduce process time and increase production. One of the problems created with CIM cell automation is caused by the dependency the sequential steps have on one another. Dependency created by the previous step increases the probability that a process error could occur due to previous variation. One way to eliminate this dependency is through the use of an in-process measuring device such as a Renishaw spindle probe …

Economic, Energy And Ghg Emissions Performance Evaluation Of A Whispergen Mk Iv Stirling Engine Μ-Chp Unit In A Domestic Dwelling, Gerry Conroy, Aidan Duffy, Lacour Ayompe

Articles

This paper presents an assessment of the energy, economic and greenhouse gas emissions performances of a WhisperGen Mk IV Stirling engine μ-CHP unit for use in a conventional house in the Republic of Ireland. The energy performance data used in this study was obtained from a field trial carried out in Belfast, Northern Ireland during the period June 2004 - July 2005 by Northern Ireland Electricity and Phoenix Gas working in collaboration with Whispertech UK. A comparative performance analysis between the µ-CHP unit and a condensing gas boiler revealed that the µ-CHP unit resulted in an annual cost saving of …

Tailsitter Attitude Control Using Resolved Tilt-Twist, Timothy Mclain, Jason M. Beach, Matthew E. Argyle, Randall W. Beard, Stephen Morris

Faculty Publications

The tailsitter aircraft merges the endurance and speed of fixed-wing aircraft with the flexibility and VTOL abilities of rotorcraft. Because of the requirement to be functional at a full range of attitudes, quaternions are typically employed to calculate attitude error. Attitude control is then accomplished by using the vector component of the error quaternion to drive flight control surfaces. This paper demonstrates that this method of driving the flight control surfaces can be suboptimal for tailsitter type aircraft and can lead to undesired vehicle movement. An alternate method of calculating attitude error called resolved tilt-twist is improved and validated. The …

Design And Assembly Of Parabolic Flight Payload To Evaluate Miniature In Vivo Surgical Robots In Microgravity, Kearney M. Lackas

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Laparoscopic surgery, also known as minimally invasive surgery (MIS), changed the face of surgery in the 1990s. With these procedures, surgeons use long, slender tools which pass through several small incisions. Performing surgery in this fashion has shown many benefits including reduced pain and recovery times, lower costs, and less scarring post-recovery.

The use of surgical robotics has shown several key advantages over MIS techniques. Minimally invasive surgeries typically require unnatural movements, have limited visibility, greatly reduce dexterity, and provide little tactile feedback. Through robot kinematics and specialized sensors, surgical robots can resolve many of these limitations, especially in terms …

Investigation Of Boiling Performance Of Graphene-Coated Surfaces, Daniel C. Stack

Renée Crown University Honors Thesis Projects - All

In this Capstone Project, I sought to investigate the boiling performance of graphene-coated surfaces. Boiling was accomplished in a pool boiling chamber, with samples of graphene-coating SiO₂ wafers. I developed a procedure for graphene transfer for sample fabrication. Samples were prepared with graphene grown on copper substrates by chemical vapor deposition (CVD). Graphene was transferred from copper substrates to SiO­₂ wafers by a thermal release transfer tape. Copper was etched away from the tape-graphene combination by ferric chloride, and the tape was peeled away after heating, leaving graphene on the SiO₂ substrate. Contact angles were measured to …

A Comparative Study: Structural Complexity Metrics Applied Against Function And Assembly Product Graphs In Predicting Market Price And Assembly Time, Sri Ram Mohinder Cherkadu Vasala

All Theses

The overarching objective of this research is to investigate the measurement and use of complexity in the prediction of product performance metrics (assembly time and market cost) for two model graph types (assembly models and function structures). This research focusses on analyzing how accurate the prediction of performance metrics are based on these graph types. This research focuses on developing four prediction models: Function Structures to predict Market Price (FS-MP), Assembly Models to predict Assembly Time (AM-AT), Function Structures to predict Assembly Time (FS-AT), and Assembly Models to predict Market Price (AM-MP). These assembly models and function structures are analyzed …

Identifying Target Properties For The Design Of Meta-Material Tank Track Pads, Venkata Sampath Dangeti

All Theses

On track vehicle systems, track pads are designed to provide traction and support the weight of the vehicle, they have limited service life due to common failure by blowout. According to the literature, blowout is a failure mode caused by overheating due to hysteresis in elastomeric materials during high speed operations. Elastomers are used primarily for their high compliance, which is essential to protect the suspension components and maintain structural integrity of the track pad. The objective of the work is to explore the use of linear elastic meta-materials with optimized topology to replace elastomers and reduce or eliminate the …

Design Of A Custom Software Application To Monitor And Communicate Cnc Machining Process Information To Aid In Chatter Identification, Valerie Pezzullo

All Theses

In any manufacturing environment, it is important to be able to monitor the Computer Numerical Control (CNC) machining process so that high quality parts can be produced in the least amount of time in order to be profitable. This involves acquiring the proper parameters needed from the machine's controller, which can prove to be difficult with proprietary machine tools that tend to limit access to the internal data collected by the controller. This closed approach to controller design also means that many technological advances that have recently become prevalent in society are not being adopted in the manufacturing industry, preventing …

Electrokinetic Particle Manipulations In Spiral Microchannels, John Dubose

All Theses

Recent developments in the field of microfluidics have created a multitude of new useful techniques for practical particle and cellular assays. Among them is the use of dielectrophoretic forces in 'lab-on-a-chip' devices. This sub-domain of electrokinetic flow is particularly popular due to its advantages in simplicity and versatility. This thesis makes use of dielectrophoretic particle manipulations in three distinct spiral microchannels. In the first of these experiments, we demonstrate the utility of a novel single-spiral curved microchannel with a single inlet reservoir and a single outlet reservoir for the continuous focusing and filtration of particles. The insulator-based negative-dielectrophoretic (repulsive) force …

Scalable Nano Particle Production Of Low Bioavailability Pharmaceuticals For Augmented Aqueous Solubility, Aaron Madden

HIM 1990-2015

The billion dollar pharmaceutical research and development pipeline suffers greatly from high attrition rates of novel therapeutic compounds within pre-clinical and clinical trials. Poor bioavailability in many new drugs, originating in the various methodologies of high throughput screening, may explain part of these growing failure rates. One interpretation of this phenomenon relies on bioavailability's correlation with aqueous solubility; much modern processing allows chemicals to fully develop without touching water, yielding upwards of 90% of new chemical entities practically insoluble in aqueous media. Thus, one approach to alleviating bioavailability and potentially clinical attrition rates necessitates augmented aqueous solubility. The amorphous nanoparticle …

Multi-Muscle Fes Force Control Of The Human Arm For Arbitrary Goals, Eric M. Schearer, Yu-Wei Liao, Eric J. Perreault, Matthew C. Tresch, William D. Memberg, Robert F. Kirsch, Kevin M. Lynch

Mechanical Engineering Faculty Publications

We present a method for controlling a neuroprosthesis for a paralyzed human arm using functional electrical stimulation (FES) and characterize the errors of the controller. The subject has surgically implanted electrodes for stimulating muscles in her shoulder and arm. Using input/output data, a model mapping muscle stimulations to isometric endpoint forces measured at the subject’s hand was identified. We inverted the model of this redundant and coupled multiple-input multiple-output system by minimizing muscle activations and used this inverse for feedforward control. The magnitude of the total root mean square error over a grid in the volume of achievable isometric endpoint …

Bellevue-Santa Fe Charter School Solar Panel Project, Dulce Arroyo Martinez, Henrik Lee, Moises Quiroz, Timothy Iafrate

Mechanical Engineering

This project covers the design, manufacture, and installation of solar panel frames on a charter school in Avila Beach, CA. Through preliminary research regarding important factors (such as solar movement, ideal panel angle, and site-specific factors), a frame that meets the standards set forth in the California Building Codes was designed. After approval by presiding authorities, parts specified in the design were ordered, inspected upon arrival, and manufactured to the design as necessary. Much of the challenge was related to the installation aspect of the project—coordination with the proper authorities and correct submission of applications was integral to the success …

The Tlc Method For Modeling Creep Deformation And Rupture, David May

HIM 1990-2015

This thesis describes a novel new method, termed the Tangent-Line-Chord (TLC) method, that can be used to more efficiently model creep deformation dominated by the tertiary regime. Creep deformation is a widespread mechanical mode of failure found in high-stress and temperature mechanical systems. To accurately simulate creep and its effect on structures, researchers utilize finite element analysis (FEA). General purpose FEA packages require extensive amounts of time and computer resources to simulate creep softening in components because of the large deformation rates that continuously evolve. The goal of this research is to employ multi-regime creep models, such as the Kachanov-Rabotnov …

Experimental Studies Of Delta Wing Parameters In Open Channel Raceway Determined Via Validated Computational Fluid Dynamics, Cole David Blakely

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

A promising feedstock for biofuels is microalgae. The most economical means of cultivating microalgae is via open raceway ponds. However, a large gap in economic feasibility exists between algae-based biofuels and traditional petroleum fuels. Recent research at Utah State University has focused on increasing biomass growth by implementing Delta Wings (DWs). DWs are placed facing the incoming flow, with a 40 degree angle of attack to create large vortices which travel downstream. The trailing vortices increase vertical mixing, which in turn increases algal growth.

Past researchers at USU quantified vertical mixing with new metrics, optimized various raceway operating conditions, and …

The Design And Testing Of A Three-Degree-Of-Freedom Small Satellite Simulator Using A Linear Controller With Feedback Linearization And Trajectory Generation, Marina A. Samuels

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

A small satellite simulator with attitude determination and control was designed and implemented in hardware. The simulator consists of inertial sensors for attitude determination and a pyramidal four-wheel momentum exchange system as the control actuators. A linearized PV controller with trajectory generation and feedback linearization was implemented, with the focus on controlling yaw. The simulator was tested on a spherical air bearing platform to allow three-degree-of-freedom operation. The simulator software was developed to read measurements from the sensors, apply the control algorithm, and send commands to the actuators. A data processing routine was developed. Electromechanical testing for the system as …

Numerical Examination Of Flux Correction For Solving The Navier-Stokes Equations On Unstructured Meshes, Dalon G. Work

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

This work examines the feasibility of a novel high-order numerical method, which has been termed Flux Correction. This is accomplished by comparing it against another high-order method called Flux Reconstruction. These numerical methods are used to solve the Navier-Stokes equations, which govern the motion of fluid flow. High-order numerical methods, or those that demonstrate a third-order and higher solution error convergence rate, are rarely used on unstructured meshes when solving fluid problems. Flux Correction intends to make high-order accuracy available to the larger world of Computational Fluid Dynamics in a simple and effective manner. The advantages and disadvantages of the …

A Computational Fluid Dynamics Validation Experiment For Forced And Mixed Convection On A Vertical Heated Plate, Jeff Robert Harris

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

A computational fluid dynamics (CFD) validation experiment is conducted for flow over a heated vertical plate. The design of the experiment to meet CFD validation standards is described. Many experiments and simulations have been completed in past studies, but none measure or present the necessary boundary conditions to define the simulation. Experimental measurements of heated flow are presented, along with corresponding boundary conditions sufficient to define the simulation's boundary conditions. Some simulation results are described, but a complete validation study is not included. The simulations are conducted by the experimentalist to ensure all necessary boundary conditions are being measured. This …

The Analysis And Manufacturing Of The Personal Vacuum Assisted Climber Ii, Rhet B. Astle

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The Personal Vacuum Assisted Climber or PVAC for short (as shown in Fig 2) is a new means for climbing walls. Unlike ordinary climbing methods used today, the PVAC scales walls via suction. This suction is produced by three spinning impellers within each vacuum motor, which removes air from a sealed area. A climber pulls down on a vacuum pressure release mechanism to release the vacuum. Foot stirrups are used by the climber to climb to the next higher step. This allows the strength of the climber's legs to lift his/her body reducing arm fatigue, allowing rapid ascension of any …

Numerical Simulation Of Flow In Ozonation Process, Jie Zhang

USF Tampa Graduate Theses and Dissertations

In the last two decades, Computational Fluid Dynamics (CFD) has shown great potential as a powerful and cost-efficient tool to troubleshoot existing disinfection contactors and improve future designs for the water and wastewater treatment utilities.

In the first part of this dissertation two CFD simulation methodologies or strategies for computing turbulent flow are evaluated in terms of the predicted hydraulic performance of contactors. In the LES (large eddy simulation) methodology, the more energetic, larger scales of the turbulence are explicitly computed or resolved by the grid. In the less computationally intensive RANS (Reynolds-averaged Navier-Stokes) methodology, only the mean component of …

Biomechanical Analysis Of Gait Kinetics Resulting From Use Of A Vacuum Socket On A Transtibial Prosthesis, Maria De Lourdes Ramos Gonzalez

Honors College Theses

The technology and design of lower limb prosthetics have evolved greatly since their introduction. The current study proposed to compare the effects of a conventional pin socket attachment and a vacuum socket attachment for a transtibial amputee. Whereas traditional measurements of gait utilize force plates and camera systems, this study made use of a small tri-axial load cell located at the base of the socket to measure the forces and moments exerted during a regular gait cycle. The hypothesis tested stated that a vacuum pump socket attachment, when compared to a non-vacuum (pin) socket, will have a significant effect on …

A Decision Support System To Measure Product Suitability For Additive Manufacturing Processes, Cynthia De Vasconcellos Barros

Theses and Dissertations - UTB/UTPA

Additive Manufacturing (AM) technologies started arising around 1980’s and they are currently considered to be the third industrial revolution. With improvements in computers, materials, and automated machines, manufacturers across several types of industries are becoming more familiar with AM processes, and it has become more common to see products that are being fabricated by using this new technology. However, there are still questions regarding when it is suitable to use Additive Manufacturing or conventional manufacturing processes depending on different factors. The purpose of this thesis is to create a Decision Support System (DSS) that will help users measure product suitability …

Corrosion Assessment And Enhanced Biocompatibility Analysis Of Biodegradable Magnesium-Based Alloys, Luis Enrique Pompa

Theses and Dissertations - UTB/UTPA

Magnesium alloys have raised immense interest to many researchers because of its evolution as a new third generation material. Due to their biocompatibility, density, and mechanical properties, magnesium alloys are frequently reported as prospective biodegradable implant materials. Moreover, magnesium based alloys experience a natural phenomena to biodegrade in aqueous solutions due to its corrosive activity, which is excellent for orthopedic and cardiovascular applications. However, major concerns with such alloys are fast and non-uniform corrosion degradation. Controlling the degradation rate in the physiological environment determines the success of an implant. In this investigation, three grades of magnesium alloys: AZ31B, AZ91E and …