Mechanical Engineering Commons^™

Inverse Volume-Of-Fluid Meshless Method For Efficient Non-Destructive Thermographic Evaluation, Hussein Awad Kurdi Saad

Doctoral Dissertations and Master's Theses

A novel computational tool based in the Localized Radial-basis Function (RBF) Collocation (LRC) Meshless method coupled with a Volume-of-Fluid (VoF) scheme capable of accurately and efficiently solving transient multi-dimensional heat conduction problems in composite and heterogeneous media is formulated and implemented. While the LRC Meshless method lends its inherent advantages of spectral convergence and ease of automation, the VoF scheme allows to effectively and efficiently simulate the location, size, and shape of cavities, voids, inclusions, defects, or de-attachments in the conducting media without the need to regenerate point distributions, boundaries, or interpolation matrices. To this end, the Inverse Geometric problem …

Synthesis And Formation Mechanism Of Cuins2 Nanocrystals With A Tunable Phase, Chao Yu, Linlin Zhang, Long Tian, Dan Liu, Fanglin Chen, Cheng Wang

Faculty Publications

Chalcopyrite CuInS₂ (CIS) hierarchical structures composed of nanoflakes with a thickness of about 5 nm were synthesized by a facial solvothermal method. The thermodynamically metastable wurtzite phase CIS would be obtained by using InCl₃ instead of In(NO₃)₃ as In precursor. The effects of the In precursor and the volume of concentrated HCl aqueous solution on the phases and morphologies of CIS nanocrystals have been systematically investigated. Experimental results indicated that the obtained phases of CIS nanocrystals were predominantly determined by precursor-induced intermediate products. The photocatalytic properties of chalcopyrite and wurtzite CIS in visible-light-driven degradation of …

Thermal Assessment Of A Latent-Heat Energy Storage Module During Melting And Freezing For Solar Energy Applications, Antonio Miguel Ramos Archibold

USF Tampa Graduate Theses and Dissertations

Capital investment reduction, exergetic efficiency improvement and material compatibility issues have been identified as the primary techno-economic challenges associated, with the near-term development and deployment of thermal energy storage (TES) in commercial-scale concentrating solar power plants. Three TES techniques have gained attention in the solar energy research community as possible candidates to reduce the cost of solar-generated electricity, namely (1) sensible heat storage, (2) latent heat (tank filled with phase change materials (PCMs) or encapsulated PCMs packed in a vessel) and (3) thermochemical storage. Among these the PCM macro-encapsulation approach seems to be one of the most-promising methods because of …

Exploration Of Electrodeposition Of Aluminum-Nickel Alloys And Multilayers In Organic Chloroaluminate Ionic Liquids, Ammar Bin Waqar

USF Tampa Graduate Theses and Dissertations

Aluminum-nickel (Al-Ni) alloys and Al/Ni bilayers were successfully electrodeposited from AlCl₃-EMIM-NiCl₂ electrolyte at room temperature. Dissolution of NiCl₂ was shown to be favorable in Lewis basic (with molar ratio of AlCl₃ < 0.5) AlCl₃-EMIM solution. The use of electrochemically active Cu working electrode as opposed to inert W induced additional Cu oxidation and dissolution in the cyclic voltammetry scan. The reduction potentials of Al and Ni were found to be ~ – 0.3 and 0.15 V vs. Al/Al³⁺ respectively. Increasing [NiCl₂] in the electrolyte leads to an increase of Ni concentration in the …

Spanning The Complexity Chasm: A Research Approach To Move From Simple To Complex Engineering Systems, Vimal Viswanathan, Julie Linsey

Faculty Publications, Mechanical Engineering

A multistudy approach is presented that allows design thinking of complex systems to be studied by triangulating causal controlled lab findings with coded data from more complex products. A case study illustration of this approach is provided. During the conceptual design of engineering systems, designers face many cognitive challenges, including design fixation, errors in their mental models, and the sunk cost effect. These factors need to be mitigated for the generation of effective ideas. Understanding the effects of these challenges in a realistic and complex engineering system is especially difficult due to a variety of factors influencing the results. Studying …

Cavitation In Vial Drop Subjected To Mechanical Shock, Houman Babazadehrokni

Electronic Theses and Dissertations

Cavitation is a phenomenon that occurs when the local pressure falls down below the critical pressure. Previous work from the Randolph lab demonstrated that protein aggregates can form when a vial of therapeutic solution is dropped onto a hard surface. The process by which this occurs is most likely shock induced cavitation. During this process, hot spots can be created with temperatures and pressures reaching thousands of Kelvin and hundreds of atmospheres, respectively, leading to degradation of protein therapeutics. This work will extend previous efforts by exploring differences generated by change in vial materials, solutions, drop methods and fill volumes. …

Multi-Modal, Surface-Focused Anticoagulation Using Poly-2-Methoxyethylacrylate Polymer Grafts And Surface Nitric Oxide Release, Surbhi Gupta, Kagya Amoako, Ahmed Suhaib, Keith E. Cook

Mechanical and Industrial Engineering Faculty Publications

This study examines platelet adhesion on surfaces that combine coatings to limit protein adsorption along with “anti-platelet” nitric oxide (NO) release. Uncoated and poly-2-methoxyethylacrylate (PMEA) coated, gas permeable polypropylene (PP) membranes were placed in a bioreactor to separate plasma and gas flows. Nitrogen with 100/500/1000 ppm of NO was supplied to the gas side as a proof of concept. On the plasma side, platelet rich plasma (PRP, 1 × 108 cell/mL) was recirculated at low (60)/high (300) flows (mL/min). After 8 hours, adsorbed platelets on PP was quantified via a lactate dehydrogenase assay. Compared to plain PP, the PMEA coating …

Vulnerability Assessment And Re-Routing Of Freight Trains Under Disruptions: A Coal Supply Chain Network Application, Ridvan Gedik, Hugh Medal, Chase Rainwater, Edward A. Pohl, Scott J. Mason

Mechanical and Industrial Engineering Faculty Publications

In this paper, we present a two-stage mixed integer programming (MIP) interdiction model in which an interdictor chooses a limited amount of elements to attack first on a given network, and then an operator dispatches trains through the residual network. Our MIP model explicitly incorporates discrete unit flows of trains on the rail network with time-variant capacities. A real coal rail transportation network is used in order to generate scenarios to provide tactical and operational level vulnerability assessment analysis including rerouting decisions, travel and delay costs analysis, and the frequency of interdictions of facilities for the dynamic rail system.

Workspace Analysis Of A Linear Delta Robot: Calculating The Inscribed Radius, Michael Louis Pauly

Graduate Theses - Mechanical Engineering

One of the most important traits of a robotic manipulator is its work envelope, the space in which the robot can position its end effector. Parallel manipulators, while generally faster, are restricted by smaller work envelopes [1]. As such, understanding the parameters defining a physical robot’s work envelope is essential to the optimal design, selection, and use of robotic parallel manipulators. A Linear Delta Robot (LDR) is a type of parallel manipulator in which three prismatic joints move separate arms which connect to a single triangular end plate [2]. In this study, general inverse kinematics were derived for a linear …

Assessment Of Noise-Induced Annoyance By Tones In Noise From Building Mechanical Systems, Joonhee Lee, Lily M. Wang

Durham School of Architectural Engineering and Construction: Faculty Publications

Prominent tones in noise generated by mechanical equipment in buildings can cause complaints from occupants in buildings. The ISO 1996-2 and ANSI S1.13 standards describe methodologies and metrics to quantify tonality perception, but the influence of tones in noise on human annoyance and performance is not fully understood yet. This paper investigates annoyance responses of humans while exposed to background noise with tonal components. Twenty participants completed digit span tasks while exposed to noise signals with differing levels of tones and overall loudness. Subjects were also asked to rate their annoyance after completing tasks under each noise signal. The subjective …

The Icon Horn Loudspeaker, Vincent Phan

Mechanical Engineering

A horn loudspeaker in layperson terms is essentially taking a megaphone and integrating it into a standard speaker. Similar to a cheerleader yelling into a megaphone, the horn loudspeaker will amplify the sound from the speaker with no additional power needed. Using standard speaker horn theory, the geometry of the “megaphone” can be engineered to tune the acoustic performance tailored to loudness and/or specific acoustics frequencies. The horn contours are similar to traditional orchestra instruments such as the French horn, trumpet, and tuba. The iconic beauty of a horn married with the quantitative engineering theory creates an aesthetic yet functional …

Direct Numerical Simulations Of Non-Premixed Ethylene–Air Flames: Local Flame Extinction Criterion, Vivien R. Lecoustre, Paul G. Grias, Somesh P. Roy, Zhaoyu Luo, Dan C. Haworth, Hong G. Im, Tianfeng F. Lui, Arnaud Trouvé

Mechanical Engineering Faculty Research and Publications

Direct Numerical Simulations (DNS) of ethylene/air diffusion flame extinctions in decaying two-dimensional turbulence were performed. A Damköhler-number-based flame extinction criterion as provided by classical large activation energy asymptotic (AEA) theory is assessed for its validity in predicting flame extinction and compared to one based on Chemical Explosive Mode Analysis (CEMA) of the detailed chemistry. The DNS code solves compressible flow conservation equations using high order finite difference and explicit time integration schemes. The ethylene/air chemistry is simulated with a reduced mechanism that is generated based on the directed relation graph (DRG) based methods along with stiffness removal. The numerical configuration …

Solid Waste As Renewable Source Of Energy: Current And Future Possibility In Libya, Tarek A. Hamad, Abdulhakim A. Agll, Yousif M. Hamad, John W. Sheffield

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Solid waste holds the greatest potential as biomass source in Libya. The rapid expansion of industry has led to increased urbanization and growing population. These factors have dramatically increased the amount of MSW (municipal solid waste) generated in Libya. However, issues related to environmentally sound MSW management - including waste decrease and clearance - have not been addressed sufficiently. This study presents an overview on solid waste that can be used as a source of bioenergy in Libya including MSW, ISW (industrial solid waste), and HSW (health care wastes) as biomass sources. The management of solid waste and valorization is …

Study Of Energy Recovery And Power Generation From Alternative Energy Source, Abdulhakim Amer A. Agll, Yousif M. Hamad, Tarek A. Hamad, John W. Sheffield

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The energy requirement pattern of world is growing up and developing technology. The available sources, while exhausting and not friendly to the environment, are highly used. Looking at partial supply and different options of environment problems associated with usage, renewable energy sources are getting attention. MSW (Municipal solid waste) composition data had been collected from 1997 to 2009, in Benghazi Libya, to evaluate the waste enthalpy. An incinerator with capacity of 47,250 kg/h was confirmed to burn all the quantity of waste generated by the city through the next 15 years. Initial study was performed to investigate energy flow and …

Fano Resonances Realized In Thz Metamaterials Composed Of Continuous Metallic Wires And Split Ring Resonators, Z. Li, S. Cakmakyapan, B. Butun, C. Daskalaki, S. Tzortzakis, Xiaodong Yang, E. Ozbay

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Modeling Of Thermal And Mechanical Behavior Of Zrb₂-Sic Ceramic After High Temperature Oxidation, Jun Wei, Lokeswarappa R. Dharani, K. Chandrashekhara, Greg Hilmas, William Fahrenholtz

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Compliant Mechanisms For Deployable Space Systems, Shannon Alisa Zirbel

Theses and Dissertations

The purpose of this research is to develop fundamentals of compliant mechanisms in deployable space systems. The scope was limited to creating methods for thick origami, developing compliant deployable solar arrays, and developing methods for stowing and deploying the arrays. The research on actuation methods was focused on a one-time deployment of the array. Concepts for both passive and active actuation were considered. The primary objective of this work was to develop approaches to accommodate thickness in origami-based deployable arrays with a high ratio of deployed-to-stowed diameter. The HanaFlex design was derived from the origami flasher model and is developed …

Design And Analysis Of Robotically-Controlled Minimally Invasive Surgical Instruments, Jordan D. Tanner

Theses and Dissertations

Robot-assisted minimally invasive surgery is used to perform intricate surgical tasks through small incisions using long, slender instruments. The miniaturization of these instruments is advantageous to both surgeon and patient because smaller instruments reduce trauma to surrounding tissue, decrease patient recovery times, and can be used in confined spaces otherwise inaccessible using larger instruments. However, miniaturization of existing designs is limited by friction between moving parts, the volume occupied by the end effector, and manufacturing and assembly constraints. The objective of this work is to develop and analyze concepts that can be used in robot-assisted needlescopic surgery. The concepts are …

The Impact Of Building Acoustics On Speech Comprehension And Student Achievement, Lily M. Wang

Durham School of Architectural Engineering and Construction: Faculty Publications

The movement for improved classroom acoustics has primarily been grounded on studies that show how building acoustics (i.e. background noise levels and room reverberation) affect speech intelligibility, as determined by speech recognition tests. What about actual student learning, though? If students do not understand each spoken word in the classroom perfectly, can they still manage to achieve high scholastic success? This presentation will review two recent studies conducted at the University of Nebraska – Lincoln, linking classroom acoustic conditions to student learning outcomes and speech comprehension (rather than simply recognition). In the first, acoustic measurements in two public school districts …

Effects Of Room Acoustics On Comprehension Of Foreign-Accented Speech By Native And Non-Native English-Speaking Listeners, Zhao Peng, Kristin E. Hanna, Brenna N. Boyd, Lily M. Wang

Durham School of Architectural Engineering and Construction: Faculty Publications

In a previous study by the authors, reverberation time (RT) and background noise level (BNL) were both found to have negative effects on native and non-native English-speaking listeners in comprehending English speech produced by native American-English-speaking talkers. Comprehension scores were adjusted for listeners’ baseline English proficiency levels. In the present study, instead of native English-speaking talkers, two native Mandarin Chinese talkers (one male, one female) with similar English spoken proficiency were recruited to produce the same speech materials used in the previous study. A similar methodology was adopted to conduct speech comprehension tests on three groups of listeners: 1) native …

Manufacturing Of Transparent Composites Using Vacuum Infusion Process, V. G.K. Menta, R. R. Vuppalapati, K. Chandrashekhara, Thomas P. Schuman

Chemistry Faculty Research & Creative Works

A novel optically transparent glass fiber reinforced polymer matrix composite has been developed by infusing a clear epoxy resin system of matching refractive index into a conventional E-glass fabric preform. Transparent composites are manufactured using a low cost, environmentally friendly vacuum infusion process. Physical and mechanical tests have been conducted. Transparent composites manufactured using the modified vacuum infusion process had a fiber volume fraction of 40%. Tensile strength and tensile modulus of these composites were 374.9 MPa and 31.74 GPa respectively. The results indicate that the transparent composites possess good physical and mechanical properties. These transparent composites form a good …

Optimised Integration Of Grid-Connected Renewable Energy Technologies For Domestic Application In Ireland, Zhe Li

Doctoral

The utilisation of renewable energy resources for electricity and thermal generation is extremely important in Ireland due to the lack of indigenous fossil fuel resources and the high dependence on imported fossil fuels. The release of environmentally-damaging greenhouse gases in the combustion of fossil fuels in electricity and thermal generation is also a major issue. In Ireland, the domestic dwelling is recognised as one of the biggest energy consumers. The use of renewable energy technologies to provide electricity, heating and hotwater can effectively offset the usage of fossil fuels. The aim of this research study was to develop a novel …

Fault Detection For Unmanned Aerial Vehicles With Non-Redundant Sensors, Brandon Jeffrey Cannon

Theses and Dissertations

To operate, autonomous systems of necessity employ a variety of sensors to perceive their environment. Many small unmanned aerial vehicles (UAV) are unable to carry redundant sensors due to size, weight, and power (SWaP) constraints. Faults in these sensors can cause undesired behavior, including system instability. Thus, detection of faults in these non-redundant sensors is of paramount importance.The problem of detecting sensor faults in non-redundant sensors on board autonomous aircraft is non-trivial. Factors that make development of a solution difficult include both an inability to perfectly characterize systems and sensors as well as the SWaP constraints inherent with small UAV. …

Design Considerations In The Development And Actuation Of Origami-Based Mechanisms, Eric W. Wilcox

Theses and Dissertations

Origami-based mechanisms have unique characteristics that make them attractive for engineering applications. However, origami-based design is still a developing area of design. Continued work to increase general understanding of key design parameters specific to origami-based mechanisms will increase the ability of designers to capture the potential benefits of origami-based mechanisms. This thesis presents a fundamental study of origami to assist designers in gaining a stronger understanding of the key parameters and capabilities of origami-based mechanisms. As a starting point a study of fundamental motions in action origami models (those that exhibit motions in their folded state) is presented to explore …

Modeling Hydrodynamic Stability Of Incline-Liquid Airblast Nozzle For Gas Turbine Combustion, Kevin Matiko

Doctoral Dissertations and Master's Theses

Fuel is a major cost item for civil transport airplanes. Minimizing fuel consumption of these crafts is a stream of economic opportunity and a stage for innovation, competition and exploration. Regardless of the fuel type, bio or crude oil based, the civil transport stakeholders would like to minimize fuel consumption of their airplanes. The mixing of fuel and air is a critical process for optimum combustion in gas turbine engines due to its high influence on the downstream combustion process. The need for minimizing fuel consumption coupled with the requirement for combustion systems to perform well at all flight conditions …

A Cfd Investigation Of The Hydrodynamic Characteristics Of Fluid Flow Through An Impeller And Multi-Objective Design Optimization Of A Centrifugal Pump, Mohammed Khammat Sagban

Doctoral Dissertations and Master's Theses

In this thesis, the first part is conducting an investigation of the hydrodynamic characteristics (pressure and velocity) of fluid flow (water) through an impeller of a centrifugal pump. To illustrate a one-dimensional model is used to identify an impeller of a GDM 10 x 12 HD centrifugal pump using Vista CPD design and BladeGen tool. A three-dimensional model is then built with a commercial software package ANSYS Blade Modeler. The structured mesh of the impeller blade is obtained by using TurboGrid system. The volute of the centrifugal pump is built in ANSYS geometry, and an unstructured mesh is accomplished by …

Biphilic Nanoporous Surfaces Enabled Exceptional Drag Reduction And Capillary Evaporation Enhancement, Xianming Dai, Fanghao Yang, Ronggui Yang, Xinyu Huang, William A. Rigdon, Xiaodong Li, Chen Li

Faculty Publications

Simultaneously achieving drag reduction and capillary evaporation enhancement is highly desired but challenging because of the trade-off between two distinct hydrophobic and hydrophilic wettabilities. Here, we report a strategy to synthesize nanoscale biphilic surfaces to endow exceptional drag reduction through creating a unique slip boundary condition and fast capillary wetting by inducing nanoscopic hydrophilic areas. The biphilic nanoporous surfaces are synthesized by decorating hydrophilic functional groups on hydrophobic pristine multiwalled carbon nanotubes. We demonstrate that the carbon nanotube-enabled biphilic nanoporous surfaces lead to a 63.1% reduction of the friction coefficient, a 61.7% wetting speed improvement, and up to 158.6% enhancement …

Second Semi-Annual Program Progress Performance Report For University Transportation Systems, Florida Solar Energy Center, David L. Block

FSEC Energy Research Center®

The Electric Vehicle Transportation Center (EVTC) supports the U.S. Department of Transportation's strategic goal of planning for near-term integration of alternative fuel vehicles as a means to build a sustainable transportation system. The project will evaluate technologies, standards and policies to ensure seamless integration of electric vehicles (EVs) into a complex transportation network and electricity grid. The EVTC will bridge the gap between deployment of electric vehicles and the traditional transportation system.

The EVTC's goals were described in detail in the previous Program Progress Performance Report. These goals have not changed significantly and this report provides updates to each of …

Flow Induced Vibration On Piezoelectric Structures: Prediction, Experiment And Applications, Felix Ewere

Von Braun Symposium Student Posters

No abstract provided.

Exergetic Life Cycle Assessment Of Electrospun Polyvinylidene Fluoride Nanofibers, Salman Ali Abbasi

USF Tampa Graduate Theses and Dissertations

Assessing the sustainability of nanomanufacturing products and processes has been difficult to achieve using conventional approaches mainly due to an inadequate inventory, large process-to-process variation, and a dearth of relevant toxicology data for nanomaterials. Since these issues are long term in nature, it is required to create hybrid methodologies that can work towards filling the existing gaps. Merging thermodynamic techniques such as the exergy analysis with environmental assessments can help make better, more informed choices while providing an opportunity for process improvement by enabling to correctly quantify efficiency loss through the waste stream, and by locating the exact areas for …