Mechanical Engineering Commons^™

Utilizing Failure Information For Mission Assessment And Optimization For Complex Systems, Charlie Destefano

Graduate Theses and Dissertations

This paper presents a new failure analysis method, Failure Identification for Mission Analysis (FIMA), which performs a general failure analysis for the overall state of a system, as well as a mission-specific analysis that identifies how failures may have differing effects on the various mission tasks that a system must complete. The FIMA method is capable of being implemented at any point in the design process. During early design stages, the FIMA method will identify various qualitative failure scenarios based on programmed functional relationships and any number of initial failures wished to be simulated. The functional relationships for this method …

Numerical And Experimental Investigation Of Variable Transportation Cooling For Reusable Thermal Protection Systems, Stefano Gulli

Mechanical and Aerospace Engineering Dissertations - Archive

This research work is focused on the numerical and experimental investigation of the transpiration cooling technique for reusable thermal protection systems. The transpiration cooling has been considered because of its higher cooling effectiveness, with respect to other active cooling techniques, in terms of minimum amount of coolant to be used and minimum interference to the external flow. An innovative approach based on the coupling of the hypersonic boundary layer with the thermal response of porous materials is used to numerically study the thermal management potential of the transpiration cooling technique. The new concept of the variable transpiration is introduced by …

Investigation Of Transmission Loss Through Double Wall Structures With Varying Small Air Gaps Using Modal Analysis., Richard Michael Phillips 1988-

Electronic Theses and Dissertations

Noise reduction testing is completed for two single steel plate constructions with different thicknesses and for two double wall constructions with different air gap thicknesses that include the same two plates used in the single plate constructions. Results compare favorably with known theory and experimental results from previous literature. These favorable comparisons include the direct relationship between mass per unit area and transmission loss for single plate constructions, the presence of a noise reduction valley near the mass-air-mass frequency, the dependency of the mass-air-mass frequency on the air gap thickness, and the existence of a bridge frequency. Despite the similarities …

Characterization Of Smoothness In Wrist Rotations, Layne Hancock Salmond

Theses and Dissertations

Smoothness is a hallmark of healthy movement and has the potential to be used as a marker of recovery in rehabilitation settings. While much past research has focused on shoulder and elbow movements (reaching), little is known about movements of the wrist despite its importance in everyday life and its impairment in many neurological and biomechanical disorders. Our current lack of knowledge regarding wrist movement prevents us from improving current models, diagnosis, and treatment of wrist disorders. In particular, while movement smoothness is a well-known characteristic of reaching movements and may potentially be used to diagnose and monitor recovery from …

Modeling And Testing Of Bistable Waterbomb Base Configurations, Brandon Holbrook Hanna

Theses and Dissertations

Origami is making an impact in engineering as solutions to problems are being found by applying origami principles (eg. flat-foldability) and using specific crease patterns as inspiration. This thesis presents an in-depth analysis of a particular origami fold -- the waterbomb base -- to facilitate its use in future engineering problems. The watebomb base is of interest due to its familiarity to the origami community, simple topology (can be made by folding a single sheet of paper four times), scalability, generalizability, and interesting kinetic behavior. It can behave as a nonlinear spring as well as a one- or two-way bistable …

A Hybrid Method For Sensitivity Optimization With Application To Radio-Frequency Product Design, Abraham Lee

Theses and Dissertations

A method for performing robust optimal design that combines the efficiency of experimental designs and the accuracy of nonlinear programming (NLP) has been developed, called Search-and-Zoom. Two case studies from the RF and communications industry, a high-frequency micro-strip band-pass filter (BPF) and a rectangular, directional patch antenna, were used to show that sensitivity optimization could be effectively performed in this industry and to compare the computational efficiency of traditional NLP methods (using fmincon solver in MATLAB R2013a) and they hybrid method Search-and-Zoom. The sensitivity of the BPF's S11 response was reduced from 0.06666 at the (non-robust) nominal optimum to 0.01862 …

Cold Roll Extrusion Machine Redesign Final Design Report, Foja Bains, Bryan Cyr, David Van Schooten

Mechanical Engineering

This report is a comprehensive review of a redesign of subsystems for a Cold Roll Extrusion Machine, a forging operation, for PCC Rollmet. Three subsystems were addressed in this project: A new Loading system, Feed system, and Lubrication system. The Loading system, and support system during developmental design stages, addressed the timely loading process of pipes onto the forging machine. After two quarters of design iteration, the group decided on a lever arm, hydraulic actuated, loading design. In the final quarter of the project, a quarter scale model of this lever arm was constructed to prove the concept of the …

Farmbot, James Cruz, Scott Herrington, Bryan Rodriguez

Mechanical Engineering

The purpose of this project was to develop the hardware for the current Farmbot to perform its primary functions, and to create a template for a system that would be adaptable for future users and developers. The scope of the project included creating a universal tool mount, a seeding system, and a watering and nutrient mixing system. This project was brought to the students by sponsor Rory Aronson, the creator of Farmbot. The Cal Poly Farmbot team was able to go through an extensive brainstorming and iterative process for each part, where testing was able to be incorporated immediately due …

Aeroponic/Hydroponic Growth Module, Sean Marrs, Joshua Moreno

Mechanical Engineering

No abstract provided.

Multi-Axis Tripod Locking Mechanism, Glenn Carros, Hannah Gause, Matthew Theiss

Mechanical Engineering

No abstract provided.

Cal Poly India Project, Derek Babine, Austen Hibler, Alex Hernandez

Mechanical Engineering

This report documents the research, ideation, and development of a solution, implemented by the Cal Poly India Sanitation Team per the request of Mr. Harish Bhutani, to solve the problem of hazardous human waste management in poor villages in India. The sponsor envisioned a universal design that would give each household in those villages access to a private toilet system because the current solution is open defecation in water sources and farming fields. The initial constraints required the project be low cost, not use of electricity or water, have the ability to cater to an 8-10 person household, and be …

Temperature Controlled Packaging Container For Biologics And Pharmaceuticals, Melinda Phan, Yufay Chow-Yee, Abraham Ho

Mechanical Engineering

Clinical Supplies Management, Inc. (CSM) provides clinical trial services to biotechnology and pharmaceutical companies by shipping pharmaceuticals to clinics and other patients. In winter 2014, CSM presented a temperature control packaging project to the Cal Poly Senior Project class. As a result, three Cal Poly Mechanical Engineering Students were tasked to design, manufacture, and qualify a shipping container that would maintain ten 10 mL vials between 2-8°C for 96 hours. The final product would have to cost less to ship than the Credo Cube, CSM’s current temperature control packaging product. After considerable research and analysis on possible temperature control technologies, …

Electric Porsche Drivetrain Re-Design, Taylor Carlson, Quinton Petty, Spencer Treffry

Mechanical Engineering

The objective of this project was to redesign the drivetrain of the electric 1977 Porsche 911 Targa S with the goal of optimizing the drivetrain for motor efficiency and performance. The focus was to redesign the interface between the electric motor and rear wheels to maximize the efficiency of power transmission from the motor to the ground.

Two systems were proposed, a fixed gear reduction and two motors with an electronic differential. The fixed gear reduction was chosen to be designed and built by replacing the stock Porsche transmission with a differential featuring a favorable gear ratio for the electric …

Carbon Black Mediated Conductive Polymer Composite, Mohamed Hussein Faris Ali

Accounting Dissertations

The central goal of this thesis is to produce electrically conductive nanocomposites made out of carbon black obtained from waste tires as filler into a polymeric matrix. Waste tires are discarded in substantial numbers on a daily basis, posing a significant environmental concern. By weight, about 25-35% of a tire is carbon black. Pyrolysis is a convenient and environmentally friendly process to produce carbon black from tires. Due to carbon black’s low density, high electrical conductivity and economical feasibility, this thesis investigates the electrical conductivity of nanocomposites that utilizes carbon black particles as fillers. As a result of its modified …

A Model Of The Diurnal Variation In Lake Surface Temperature, Jonathan L. Hodges

All Theses

Satellite measurements of water surface temperature can benefit several environmental ap-plications such as predictions of lake evaporation, meteorological forecasts, and predictions of lake overturning events, among others. However, limitations on the temporal resolution of satellite mea-surements restrict these improvements. A model of the diurnal variation in lake surface temperature could potentially increase the effective temporal resolution of satellite measurements of surface tem-perature, thereby enhancing the utility of these measurements in the above applications. Herein, a one-dimensional transient thermal model of a lake is used in combination with surface tempera-ture measurements from the Moderate Resolution Imaging Spectroradiometer (MODIS) instrument aboard the …

Design, Analysis And Implementation Of An Experimental System To Harvest Energy From Atmospheric Temperature Variations Using Ethyl Chloride Filled Bellows, Gibran Ali

All Theses

The increase in global warming and the dwindling supplies of fossil fuels have shifted the focus from traditional to alternate sources of energy. This has resulted in a concerted effort towards finding new energy sources as well as better understanding traditional renewable energy sources such as wind and solar power. In addition to the shift in focus towards alternate energy, the last two decades have offered a dramatic rise in the use of digital technologies such as wireless sensor networks that require small but isolated power supplies. Energy harvesting, a method to gather energy from ambient sources including sunlight, vibrations, …

Numerical Simulation Of The Heat Leakage At The Gasket Region Of Domestic Refrigerators, Feng Gao

All Theses

Computational Fluid Dynamics (CFD) simulations are performed to investigate the heat loss at the gasket of a standard over/under domestic refrigerator. The study numerically simulates a unique experimental test cell with only the gasket region exposed to the ambient environment and other parts protected by insulation (see picture below). The test cell is cubic with an interior cavity having dimensions 2' x 2' x 2' within which a heating element is placed to create a specified temperature difference. A matching set of door and side panels exposes a 2' width of the gasket region to heat transfer with the surroundings. …

Machine Shop Learning Kits, Samantha Kelley, Ellen Chambers

Mechanical Engineering

Currently in the Cal Poly Machine shops, students are struggling to find ways to fulfill the 10 hours of shop experience required to gain their Yellow Tag certification. Red Tag is the first level of certification students generally achieve their freshman year. It allows them to use basic machine tools such as drills, shears, benders, etc. Then after completing 10 hours of shop experience they can take the Yellow Tag test, which gains them access to use a welder, mill, and lathe. The heads of the machine shop, the shop technicians, and the mechanical engineering students will all have different …

Compression Tester Shop Press, Colby Johnson, Brett Russon, Taylor Vandenhoek

Mechanical Engineering

A piece of machinery designed to carry out compression and bending tests on building materials constructed by the Center for Vocational Building Technologies (CVBT) in Isarn, Thailand.

Semi-Automated Glass Mat Splice Operation For Asphalt Shingle Line, Justin Bracci, Harry Zhao, Chad Linafelter

Mechanical Engineering

The following report details the senior project sponsored by GAF Materials Corporation, Shafter, CA in regards to semi-automating a glass-mat splicing table for asphalt roofing shingle production. Herein includes details, research, design, and analysis regarding the semi-automation of the gluing processes for the splicing table. A working prototype was manufactured and tested for the future implementation onto GAF’s production line or further senior project involvement.

Wingtip Dynamics Simulator, Eugene Fox, Nick Rodriguez, Steven Rieber

Mechanical Engineering

Raytheon is a defense contracting company with an electronic warfare division that is developing a radio frequency signal triangulation system. Part of the focus in improving this technology is the need for accurate and real time locational knowledge of the signal receivers, which are located at the tips of aircraft wings. Due to turbulence during flight, the fluttering motion of the wings alter the distance and angle relationships of the two receivers and add noise to the received signal data, which negatively affect the triangulation estimates. To mitigate this error caused by the wing flutter, Raytheon is developing a software …

Speaker Dependent Voice Recognition With Word-Tense Association And Part-Of-Speech Tagging, Theodore Philip King Ernst

Doctoral Dissertations and Master's Theses

Extensive Research has been conducted on speech recognition and Speaker Recognition over the past few decades. Speaker recognition deals with identifying the speaker from multiple speakers and the ability to filter out the voice of an individual from the background for computational understanding. The more commonly researched method, speech recognition, deals only with computational linguistics. This thesis deals with speaker recognition and natural language processing. The most common speaker recognition systems are Text-Dependent and identify the speaker after a key word/phrase is uttered. This thesis presents Text-Independent Speaker recognition systems that incorporate the collaborative effort and research of noise-filtering, Speech …

Induction Of Differentiation Of Dental Pulp-Derived Mesenchymal Stem Cells (Dpsc), Aubrey Young

UNLV Theses, Dissertations, Professional Papers, and Capstones

Mesenchymal stem cells are derived from a variety of human tissues and are being bioengineered and studied for possible uses in the advancement of medicine. Recent efforts are being focused on Dental Pulp Stem Cells (DPSC's) due to the accessibility of this tissue. Many factors influence DPSC quality and quantity, including the specific methods used to isolate, collect, concentrate, and store these isolates once they are removed. Ancillary factors, such as the choice of media, the selection of early versus late passage cells, and cryopreservation techniques may also influence the differentiation potential and proliferative capacity of DPSC isolates.

The objective …

Investigating The Relationship Between High Temperature Flow Stress And Friction Stir Weldability In Hsla Steels, David Jordan Walser

Theses and Dissertations

The feed rate at which a defect free friction stir weld can be run (friction stir weldability) on an HSLA steel plate can vary widely between heats that meet the same specified physical properties. Consequently, every time a new heat of HSLA steel is obtained, exploratory welds must be run to determine the proper feed rate for that plate. Previous research suggests that the varying levels of alloying elements related to high temperature physical properties between the different heats causes the observed change in friction stir weldability. Because of this, it was hypothesized that the high temperature physical properties of …

A Variable-Stiffness Compliant Mechanism For Stiffness-Controlled Haptic Interfaces, Jeffrey C. Hawks

Theses and Dissertations

In this research a variable-stiffness compliant mechanism was developed to generate variable force-displacement profiles at the mechanisms coupler point. The mechanism is based on a compliant Roberts straight-line mechanism, and the stiffness is varied by changing the effective length of the compliant links with an actuated slider. The variable-stiffness mechanism was used in a one-degree-of-freedom haptic interface to demonstrate the effectiveness of varying the stiffness of a compliant mechanism. Unlike traditional haptic interfaces, in which the force is controlled using motors and rigid links, the haptic interface developed in this work displays haptic stiffness via the variable-stiffness compliant mechanism. The …

A Preventive Maintenance Framework In Dairy Production Operations, Maria F. Vargas

Theses and Dissertations - UTB/UTPA

Dairy operations suffer frequent stops. Product shrinkage is a consequence of downtime, which includes losses of packaging material, scraped finish product and capacity. This work proposes a troubleshooting methodology to identify causes of downtime, estimation of waste cost, and minimization of operation disruptions by applying a combination of a cost function to assess waste, and performance measurements. The drinkable yogurt process is evaluated to find the principal areas for wasted bottles and yogurt. In order to make a decision about which of those sources to address, a General Cost Function is used to estimate waste cost which include measurements that …

Effects Of Vapor Grown Carbon Nanofibers On Electrical And Mechanical Properties Of A Thermoplastic Elastomer, Daniel Thomas Basaldua

Theses and Dissertations - UTB/UTPA

Carbon nanofiber (CNF) reinforced composites are exceptional materials that exhibit superior properties compared to conventional composites. This paper presents the development of a vapor grown carbon nanofiber (VGCNF) thermoplastic polyurethane (TPU) composite by a melt mixing process. Dispersion and distribution of CNFs inside the TPU matrix were examined through scanning electron microscopy to determine homogeneity. The composite material underwent durometer, thermal gravimetric analysis, differential scanning calorimetry, heat transfer, hysteresis, dynamic modulus, creep, tensile, abrasion, and electrical conductivity testing to characterize its properties and predict behavior. The motivation for this research is to develop an elastomer pad that is an electrically …

Light Field Imaging Applied To Reacting And Microscopic Flows, Jonathon Remy Pendlebury

Theses and Dissertations

Light field imaging, specifically synthetic aperture (SA) refocusing is a method used to combine images from an array of cameras to generate a single image with a narrow depth of field that can be positioned arbitrarily throughout the volume under investigation. Creating a stack of narrow depth of field images at varying locations generates a focal stack that can be used to find the location of objects in three dimensions. SA refocusing is particularly useful when reconstructing particle fields that are then used to determine the movement of the fluid they are entrained in, and it can also be used …

Experiment And Simulation Of The Acoustic Signature Of Fatigued-Cracked Gears In A Two-Stage Gearbox, Matthew James Ostiguy

Master's Theses

This thesis focuses on the development of a health monitoring system for gearbox transmissions. This was accomplished by developing and understanding a two-stage gearbox computer model that emulates an actual gearbox test rig. The computer model contains actual gearbox geometry, flexible shafts, bearings, gear contact forces, input motor torque, output brake torque, and realistic gearbox imbalance. The gear contact force of each gear stage and the input bearing translational acceleration were the main outputs compared between a healthy gearbox and damaged gearbox computer model. The damage of focus was a fatigue crack on the input pinion gear. A sideband energy …

Methane Production By A Packed-Bed Anaerobic Digester Fed Dairy Barn Flush Water, Sean Richard Thomson

Master's Theses

Packed-bed digesters are an alternative to covered lagoon digesters for methane production and anaerobic treatment of dilute wastewaters such as dairy barn flush water. The physical media of packed-beds retain biofilms, often allowing increased treatment rates. Previous studies have evaluated several types of media for digestion of dilute wastewaters, but cost and media fouling have setback commercial development. A major operational cost has been effluent recirculation pumping.

In the present effort, a novel approach to anaerobic digestion of flush dairy water was developed at pilot-scale: broken walnut shells were used as a low-cost packed-bed medium and effluent recirculation was replaced …