Mechanical Engineering Commons^™

Using Optical Dielectrophoresis For Microbead And Cell Manipulation, Leigh K. Smith

Mechanical Engineering Undergraduate Honors Theses

Dielectrophoresis is a common method used to manipulate particles on the microscopic scale. Optically Induced Dielectrophoresis or ODEP is the specific method used in this research. All experiments were conducted in Dr. Tung’s Micro and Nano Systems lab at the University of Arkansas’ ENRC. An ODEP system was created in the lab for manipulating microbeads (6-10 micrometers (μm) in diameter) and E. coli cells (1-2 μm in diameter).

Experiments were performed on the microbeads to see how changing the parameters of the device affects the force caused by ODEP on the beads. The parameters that could be changed in the …

Optimal Parameters For Electrode Free Local Anodic Oxidation Lithography, Maxwell C. Cleveland

Mechanical Engineering Undergraduate Honors Theses

Dr. Steve Tung’s research lab is developing a device for sequencing DNA strands. A key component of this device is a nano sensor fabricated using monolayer graphene. To create the sensor, the graphene must be precisely patterned. Graphene, a single layer of carbon atoms, is an ideal material for detecting electrical signals from DNA bases due to its excellent conductivity.

The current fabrication method uses Atomic Force Microscopy (AFM) in combination with Electrode-Free Local Anodic Oxidation (LAO) lithography. While AFM is typically employed for nanoscale imaging, pairing it with LAO lithography enables the patterning of graphene into nanoribbons capable of …

The Prototype Of A Fully Automated Pressuremeter For Various Geotechnical Applications, Anuar Akchurin

Theses and Dissertations

The geotechnical engineering field requires high-quality in-situ testing equipment that ensures consistency in the test execution. This research focuses on developing and testing a prototype of a fully automated pressuremeter control unit to allow the industry to obtain reliable and controlled stress-strain data, thereby improving efficiency and reducing testing time.

The objectives of this work are to design and develop a system with the necessary components to perform the pressuremeter test, integrate the testing procedure into the state machine design, enable automated testing, and validate the results by comparing the stress-strain data with that obtained from the existing hand-operated pressuremeter …

Tailoring Functional And Sensing Properties Of Polymer-Ceramic Composites Via 3d Printing, Alexis Lopez

Open Access Theses & Dissertations

Section 1.1. Abstract This chapter investigates the use of direct ink write (DIW) additive manufacturing to control grain orientation in non-toxic barium titanate (BTO) ceramics by blending spherical and platelet-shaped particles in the ink. A series of inks containing 0–40 wt.% BTO platelets were formulated with poly(vinyl alcohol), polyethylene glycol, poly(acrylic acid-co-maleic acid), and ammonium hydroxide to ensure printability and homogeneous dispersion. Cylindrical specimens (20 mm × 3 mm) were printed using a Hyrel 30M DIW system and subjected to de-binding (650 °C, 2 h) followed by a two-step sintering schedule (T₁: 1200–1350 °C; T₂: 700–850 °C; 24 h dwell). …

Advancing Additive Manufacturing For Extreme Environments Through Simulated Microgravity Printing, Laura Nayeli Molina

Open Access Theses & Dissertations

Additive Manufacturing (AM) holds significant potential for space exploration by enabling on-demand fabrication of components, reducing payload costs, and enhancing mission adaptability. However, microgravity introduces challenges in thermal regulation, material deposition, and structural integrity. This research explores the feasibility of submerged AM using neutral buoyancy in silicone oil to simulate microgravity conditions on Earth. A 3D printer was modified for submerged operation, with samples printed under three conditions: no oil (ambient air), submerged in oil, and simulated microgravity at varying temperatures. Mechanical tests, fracture surface analysis, and density measurements were performed to evaluate tensile strength, surface adhesion, and dimensional stability. …

Engineering Of Metallic Interpenetrating Phase Composites For The Control Of Deformation And Failure Modes During Dynamic Events, David Kiyoshi Santacruz

Open Access Theses & Dissertations

Aerospace components, automotive structures, and ballistics armor are all engineered to withstand high strain rate service events through a combination of material selection and design choices. However, structural components may be less effective when their implementation is constrained by other factors such as weight or design limitations. To meet these challenges, the development of next-generation materials will need to increasingly rely on composite material systems rather than monolithic materials. This thesis presents the fabrication, dynamic characterization testing, and post-mortem analysis of 316L/A356 interpenetrating phase composites (IPCs) made from the PrintCasting methodology. These composites consist of additively manufactured 316L stainless steel …

Advancing Precision And Autonomy In Agriculture And Medical Imaging Through Ai And Computer Visions, Tan-Hanh Pham

Theses and Dissertations

Deep learning has revolutionized numerous fields by enhancing precision, automation, and decision-making capabilities. This dissertation explores its applications in agriculture and medical image processing, introducing novel methodologies to improve accuracy and efficiency in these domains. These fields hold critical societal importance -- agriculture underpins global food security and sustainability, while medical imaging drives advancements in diagnostics and personalized healthcare, both benefiting significantly from data-driven innovations. In agriculture, deep learning is applied to precision spray systems through droplet analysis. Specifically, a generative model is designed to create synthetic droplet images, addressing the challenge of limited training samples, which are expensive …

Vibration-Based Algorithm For Diagnostic And Prognostic Condition Monitoring Of Railroad Bearings And Wheels, Jeffery Ray Pams

Theses and Dissertations

Bearing and wheel failure accounts for the majority of equipment-related train derailments on US railroads. Current wayside monitoring systems have been insufficient in the prevention of catastrophic derailments prompting the rail industry to explore the possible integration of onboard condition monitoring systems into their rail operations. The University Transportation Center for Railway Safety (UTCRS) in partnership with Hum Industrial Technology, Inc., has developed a wireless onboard system intended for the condition monitoring of railroad bearings and wheels. This thesis presents the development, evaluation, and implementation of an algorithm designed to be used in conjunction with these systems to provide railroad …

Analysis And Modeling Of Porous Media Networks In Petroleum Reservoirs Through Microscale Thermography And Core Flooding, Alan Petrovich-Mar

Theses and Dissertations

Reservoir rocks are porous materials that are an important area of study since they are present in reservoir sites rich in crude oil. It is important to understand the spreading phenomena on the rock surface and through the porous structure during fluid flow through these porous materials. For a complex system like reservoir rocks, factors such as spatially varying chemical composition and topography, multidimensional porosity, temperature, humidity, and existing oil/water in the pores can affect wettability and be a detriment to oil recovery.

The interaction of core samples with different porosity and permeability with water after proper cleaning procedures and …

Development And Tribological Characterization Of Uhmwpe-Tin Composite Coatings Deposited By Electrostatic Spraying, Jarrod Keith Perez

Theses and Dissertations

The increasing demand for inert, wear-resistant, cost-efficient, environmentally friendly, and low-friction coatings has driven extensive research into polymer-based solutions. Among these, ultra-high-molecular-weight polyethylene (UHMWPE) has emerged as a strong candidate due to its low density, anticorrosion properties, self-lubricating nature, affordability, and ease of processing. However, its low load-bearing capacity limits its widespread use in high-stress tribological applications. To overcome this limitation, this project investigates the development and characterization of UHMWPE composite coatings reinforced with titanium nitride (TiN) particles at varying concentrations (2.5, 5, and 10 wt%) to enhance their mechanical properties and wear resistance.

Reinforcement Learning For High-Dimensional Tradespace Exploration In Multi-Objective Optimization, Aaditya Kothavade

All Theses

Engineering design optimization often requires balancing multiple competing objectives while navigating complex, high-dimensional tradespaces. Despite significant advances in tradespace exploration techniques, current methods face critical challenges in efficiently navigating high-dimensional design spaces. As the number of design variables and competing objectives increases, traditional multi-criteria decision-making and optimization methods struggle to explore the vast solution space comprehensively. The curse of dimensionality exacerbates this issue, making it impractical to analyze all possible solutions and effectively identify trade-offs between objectives. Additionally, the computational complexity of high-dimensional spaces further complicates optimization, making exhaustive solution analysis infeasible. Traditional multi-objective optimization methods rely on static Pareto-front …

Stability Of Holes In Granular Raft, Plabon Kumar Saha

All Theses

A granular raft at an oil–water interface exhibits unique mechanical properties, including the ability to form and sustain stable holes. In this study, we experimentally investigate the formation, stability, and collapse dynamics of holes in particle rafts composed of micrometer-sized particles. Holes are created using a hollow cylinder, which generates a meniscus that inhibits particle motion, thus stabilizing the hole. Stable holes are formed when their size reaches a critical value, which depends upon the capillary length. The critical hole size does not depend upon the circularity of the hole. We show that capillary forces due to the presence of …

Micro Wind Turbine - Modelling And Testing, Mohammad Uzair Bhati

All Theses

The global energy demand continues to rise as people consume more electricity to power their personal electronics, electric vehicles, and consumer products such as outdoor tools. To generate renewable energy, large scale solar and wind farms continue to receive the most commercial attention. However, portable wind energy turbines have the potential to generate sufficient power for cell phones and other electronic devices. There are two types of wind turbines, horizontal and vertical axis each having their pros and cons. Vertical-axis wind turbines are the main focus of this thesis, with a reduction in their form factor or size and portable …

An Experimental And Computational Study Of High-Temperature Creep Behavior In Fully Lamellar Titanium Aluminide Alloys, Karel M. Ziminsky

All Theses

Titanium aluminide alloys have seen increased aerospace applications in recent years, especially in aircraft jet engines. They can offer benefits such as improved high-temperature strength compared to titanium alloys and reduced density compared to nickel alloys. These alloys also can exhibit high creep resistance due to their fully lamellar microstructure. These mechanical properties are desirable for components like turbine blades, where tight tolerances must be maintained for optimal performance. This research examines the high-temperature creep behavior of a fully lamellar two-phase titanium aluminide alloy, TNM® (Ti-43.5Al-4Nb-1Mo-0.1B), through experimental and computational methods. Scanning electron microscopy studies reveal the presence of large …

Developing Reduced Order Models For Gas Bubble Formation In Irradiated Metals Using Integrated Phase Field Modeling And Koopman Operator Theory, John M. Eggemeyer V

All Theses

Irradiation damage in materials is prevalent in nuclear components, posing significant risks in the safety and reliability of nuclear reactors. Phase field models offer a versatile framework for modeling irradiation damage in materials at mesoscales. Such high fidelity method has been used to model the formation of fission gas bubbles superlattice, a microstructure array occurs at certain irradiation conditions (dose, dose-rate, and temperature). To overcome the high computational cost of phase field modeling, Koopman operator theory is applied to create reduced order models, allowing for instantaneous simulations of fission gas bubble behaviors. These low fidelity models are integrated into machine …

Defining Fidelity For Tradespace Application, Aditya Agrawal

All Theses

This research proposes a definition of tradespace fidelity and presents a study on its effectiveness in the tradespace. Tradespace exploration helps evaluate various design options, allowing engineers to make informed decisions in early design stages. Fidelity generally refers to how closely a model approximates reality. However, the definition of fidelity has been inconsistently defined and interpreted in various contexts concerning particular problems. In some cases, it is a measure of accuracy; in others, information; in another, uncertainty; and in others, computational complexity. Fidelity is poorly and inconsistently defined in the literature. In general, higher fidelity models tend to be more …

Mechanistic Insights Into Polymer-Assisted Graphene Exfoliation: The Roles Of Velocity, Adhesion, Cohesion, Temperature, Peeling Mode, And Edge Defect Via Coarse-Grained Molecular Dynamics, Linjiale Dai

All Theses

Graphene exfoliation is a critical step in the fabrication of high-quality graphene

layers. However, the underlying fracture mechanisms remain poorly understood. In this

work, I employed coarse-grained (CG) molecular dynamics (MD) simulations to

investigate how factors such as interfacial binding energy, substrate cohesion, temperature,

peeling mode, and edge defects influence the outcome of the exfoliation process. To model

polymer-assisted mechanical exfoliation, I used a finite-size system in which multilayer

graphene (MLG) is sandwiched between two thin polymer films. Leveraging the

spatiotemporal efficiency of the CG model, I performed fifty simulation iterations per

parameter set and analyzed the results from a …

Manipulating Martensitic Transformation And Residual Stress Development In Stress Superposed Incremental Forming Of Ss304, Elizabeth M. Mamros, Fabian Maaß, Thomas Gnaupel-Herold, A. Erman Tekkaya, Brad L. Kinsey, Jinjin Ha

Faculty Journal Articles

Stress superposition is one of the strategies used in metal deformation processes to increase the material formability, decrease the required forming forces, and create highly customized components. To investigate the effects of tensile and compressive stresses superposed to the single point incremental forming (SPIF) process, experiments and numerical simulations were conducted for a stainless steel 304 (SS304) truncated square pyramid geometry. Tensile stresses were superposed in-plane on the specimen blank by a custom hydraulic frame, and compressive stresses were incorporated via a polyurethane die. Identified parameters for a martensitic transformation kinetics model for SS304 were used in a two-step finite …

Bayesian Model Updating Of Structural Parameters Using Temperature Variation Data., Ujjwal Adhikari

Electronic Theses and Dissertations

Physical digital twins have now emerged as a technology in structural health monitoring and other domains of structural modeling. A Finite Element Model can be a tool for digital twin technology in conjunction with measured physical data. Developing an accurate digital model requires the integration of various parameters to replicate the real structure; however, temperature is dynamically changing, resulting in difficulty in the identification of structural parameters. Typically, temperature is considered noise or filtered out. Limited research has addressed the physics-based model using temperature variation related to structural modal properties. Finite Element Model Updating (FEMU) is a typical inverse problem-solving …

Storytelling In Undergraduate Engineering Courses As Inclusive Curriculum: Improving Students’ Sense Of Belonging, Identity, And Persistence, Brooke Heller

Boise State University Theses and Dissertations

The engineering field experiences high attrition rates and a historical lack of diversity in the United States. Sense of belonging and identity have been shown to impact persistence, especially for people from historically marginalized communities. This three-paper dissertation is focused specifically on this phenomenon in academia and methods of contributing to improving and progressing conditions. To pivot to a new paradigm in which people from diverse backgrounds feel welcome and valued, there is a need for more inclusive practices in the field, particularly in the form of curriculum in academia. Inclusion has been shown to improve outcomes for students from …

Integrity Assessment Of Shipping Line Pipelines Using Risk-Based Analysis To Determine Risk And Maintenance Strategies, Ade Ratih Anggraini, Dwi Marta Nurjaya

Journal of Materials Exploration and Findings

Pipeline Shipping Lines X, Y & Z are classified as critical infrastructure, being the only transportation through the crude oil lifting from P and R location to the transfer station in NM Area. To maintain the workflow of the Shipping Line, integrity assessments and risk evaluation are required to ensure the operational and safety. Anomalies were found by analysing inspection, monitoring, and repair data, while the pipelines' future integrity was assessed by calculating the remaining life. Risk-Based Analysis (RBA), which is a modification of Kent Muhlbaeur's method, is employed to conduct the risk assessment using the Probability of Failure (POF) …

Assessment Of H2s-Induced Cracking Susceptibility In Steam Line Pipes And Weld Zones During Geothermal Well Construction, Riene Kaelamanda Pragitta, Yudha Pratesa

Journal of Materials Exploration and Findings

The susceptibility of steam line pipes, especially in the HAZ (heat-affected zone) and weldment areas, to hydrogen sulfide in the geothermal industry is crucial to understand from the early stages, particularly during construction. The combination of tensile stress from residual stresses after welding and metallurgical phase transformation makes the joint areas vulnerable to sulfide stress cracking. This condition becomes even more extreme when the equipment operates during the well stimulation phase. This research assesses the severity of H₂S-induced cracking using NACE MR0175 and ISO 15156-1 standards, focusing on the effects of pH and partial pressure of H₂S (p_{H₂S …}

Co-Designing Manufacturing Systems For Robustness And Resilience: A Decision-Based Design Perspective, Mathew Baby

Theses and Dissertations

Manufacturing systems (MSs) comprise various stakeholders associated with the manufacture and supply of products required by customers and are interrelated by the flow of materials and information. The interrelated stakeholders make system-specific decisions and stakeholder-specific decisions across multiple levels of a decision hierarchy to satisfy many conflicting system-specific and stakeholder-specific requirements that define system and stakeholder performances. Given the stakeholder interrelations and conflicting nature of system-specific and stakeholder-specific requirements, system and stakeholder performances are correlated and conflicting.

In the Industry 5.0 era, there is an increased emphasis on the creation and equitable distribution of value among all the stakeholders in …

Tracing Wave Induced Flow Field Surrounding Reef Balls, Alexis Scheele

Theses and Dissertations

This study aims to explore the wave-induced flow dynamics around Reef Ball models using dye tracing techniques. Reef Balls are hemispherical artificial reefs with a hollow center and cavities throughout each face, they are designed in this manner to enhance coral reef restoration. Reef Balls rely on wave energy and current motion to facilitate water circulation and nutrient exchange within and surrounding their structure. To understand how wave action influences flow patterns around these artificial reefs, a scaled model experiment was designed to simulate real-world conditions. The experiments were conducted in the wave flume at Florida Institute of Technology’s Surf …

Retrofitting Farm Equipment With Airflow Sensors, Jacob Bybee

Undergraduate Honors Capstone Projects

In the Fall of 2024, our farm in Idaho upgraded our equipment from conventional seeding drills to more modern and sophisticated air seeder drills, particularly the John Deere 1900 Commodity Air Cart and John Deere 730 Air Disk Drill. In our case, this equipment was purchased used at an auction and had been a little modified. One modern convenience that this certain 730 Drill did not come with was a blockage monitoring system to alert the operator that a seed distribution tube was no longer distributing seeds. My question the became: Can an affordable, reliable airflow sensor system be designed …

Training Lander For Rover Arm Testing, James Peck

Undergraduate Honors Capstone Projects

The purpose of this honors capstone project is to design and fabricate a training lander to support the Utah State University (USU) rover team in preparation for the University Rover Challenge (URC). The URC is an international collegiate competition featuring four missions, one of which—the Equipment Servicing Mission—demands a high level of robotic arm functionality and operator skill. Historically, USU's rover teams have struggled to qualify for the URC finals, in part due to limited hands-on training opportunities with the robotic arm.

To address this gap, the training lander replicates the tasks found in the URC Equipment Servicing Mission, such …

Tribological Characterization Of Laser Microtextured Ti-6al-4v Eli Alloy For Biomedical Applications, Nicholas Ricardo Perez

Theses and Dissertations

Titanium alloys have been gaining popularity in multiple fields due to their impressive physical properties, but struggle with poor tribological performance. This thesis aims to mitigate the poor tribological performance of titanium alloys through a laser microtexturing process. Ti-6Al-4V ELI (Extra Low Interstitial) alloy disks were evaluated against ultrahigh molecular weight polyethylene (UHMWPE) and polyether ether ketone (PEEK) pins. Four texturing patterns were created by changing the texture area fraction from 5 to 20% that were evaluated against untextured control samples. The tribological properties of the laser textured Ti-6Al-4V ELI disks were determined using a pin-on-disk tribometer under lubricated sliding …

Autonomous Control Of A Hybrid Unmanned Aerial Towed System On A Moving Platform, Zachary M. Miller

Graduate Theses and Dissertations (2019 - present)

With tethered rotor drones being more popular for aerial surveillance, moving platforms for tethered drones are being researched. However, these systems require constant power to the rotor drones for stabilization. With this difficulty in power consumption, a hybrid drone solution is presented. The hybrid drone is similar to an airplane, with quadcopter motors attached for stabilization and thrust when not moving.

The controller for the hybrid drone was tested and verified in simulation. The simulation of the system was built in Fortran and consists of a driver, a tether, and a hybrid drone. The driver was modeled after a generic …

Quantifying The Threshold For Fragmentation Of Newtonian And Non-Newtonian Drops, Aditya Parik

All Graduate Theses and Dissertations, Fall 2023 to Present

This dissertation investigates how the properties of liquid drops influence the minimum aerodynamic forces needed to cause the drop to fragment (breakup). For this work, we focus only on aerodynamic forces that are applied on a stationary drop by a sudden, uniform flow, a process called impulsive acceleration. Previous studies have largely focused on the fragmentation of spherical drops of Newtonian fluids (liquids with constant viscosity, like water), when impulsively accelerated in air-like ambient medium. Such systems only capture a limited range of drop and ambient properties (described by non-dimensional groups). Many real-world applications, such as aerial fire retardant delivery, …

Quantifying Buoyancy-Driven Exchange Flows Over Obstacle At The Great Salt Lake Using Rans Cfd, Mohammad Ikram Hossain Talukdar

All Graduate Theses and Dissertations, Fall 2023 to Present

This study examines how barriers, such as berms, affect the movement of water in the Great Salt Lake in Utah. The lake experiences two types of water flow: one, called a unidirectional gravity current, where denser water flows in a single direction, and another, known as buoyancy-driven exchange flow, where water flows in two opposite directions due to differences in both water density and surface elevation. These flows are important for understanding how water mixes and moves between the northern and southern parts of the lake. Using computer models, we simulated how these two types of water flows behave when …