Mechanical Engineering Commons^™

Thermal Hydraulic Turbine Dynamometer, Ryan Baskett, Alexander Campbell, Andrew Puntorno-Carlberg

Mechanical Engineering

No abstract provided.

Child Carrier: Senior Project, Cordell Hollingsworth, Jacob Puppo, Drew Sapp

Mechanical Engineering

No abstract provided.

Tron 2.0 - The Experience, Alecsandro G. Vitale, Alexander W. Billings, Jordan Delfino, William Beechinor, Kelly Rorden

Architectural Engineering

The goal of this senior project was to come up with a structural-engineering-related schematic design for a roller coaster to be installed in Disneyland called TRON 2.0: The Experience. This involved looking at both design processes that we had already learned through our curriculum as well as researching concepts that were previously foreign to us, namely the dynamic application of loads and the effects of fatigue stresses.

A story was established based on the source material: the TRON movies produced by Walt Disney Studios. Thematic elements from the story were used as the basis for design implications that would become …

High Temperature Hepa Filter Test Unit Upgrades, Alexander Krippner, Ian Corcorran, Michael Burlando

Mechanical Engineering

No abstract provided.

High Speed Jet Turbine Test Final Report, Kenneth Enstrom, Cameron Naugle, Isaac Thomas, Cody Lee

Mechanical Engineering

At high flight altitudes and speeds, external airplane elements are subject to immense loads. External devices must be put through testing that simulates these loads to ensure safety of the device. Our system will subject a device in need of testing to a jet of air, similar to wind seen on the surface of an airplane. The High Speed Air Jet Turbine Test project team has been tasked to design, build, and test an apparatus capable of acquiring real world flight data for micro-ram air turbines (microRAT). The micro-RAT is a device that provides power to an electrical device by …

Modeling The Residual Useful Life Of Railroad Bearing Grease, Thania Alejandra Martinez

Theses and Dissertations

Railroad bearing performance is often constrained by the life of its lubricant. The lubricant life is determined by tribomechanical processes that are present during bearing operation. No known physical models exist to predict the railroad bearing lubricant life. This thesis summarizes the efforts undertaken in the development of empirical models that can accurately predict the residual useful life of railroad bearing grease. Modeling techniques to be employed include regression, regression trees, and split plots. The grease samples used to populate this model come from healthy and faulty bearings that were run under different loads, speeds, and ambient conditions in a …

Pressure Field Estimation Using Particle Image Velocimetry, Jean O. Calzada

Theses and Dissertations

In recent years, scientist and engineers have shown the advantages created by using the Particle Image Velocimetry (PIV) method as flow diagnostic tool to characterize instantaneous velocity fields. One of the important benefits is found on its non-intrusive nature, this leads to accurate velocity fields. From the velocity field obtained by PIV important quantities can be derived, such as pressure and vorticity. The present study, uses PIV data of an incompressible turbulent pulsed jet to determine the pressure field associated with the flow field. The pressure is calculated by using the averaged velocity field along with three different fundamental equation: …

Sparse Aperture Speckle Interferometry Telescope Active Optics Control System, Matthew Clause

Master's Theses

A conventional large aperture telescope required for binary star research is typically cost prohibitive. A prototype active optics system was created and fitted to a telescope frame using relatively low cost components. The active optics system was capable of tipping, tilting, and elevating the mirrors to align reflected star light. The low cost mirror position actuators have a resolution of 31 nm, repeatable to within 16 nm. This is accurate enough to perform speckle analysis for the visible light spectrum. The mirrors used in testing were not supported with a whiffletree and produced trefoil-like aberrations which made phasing two mirrors …

In Vitro Multi-Scale Patient-Specific Modeling Of Hemodynamics In Stage 1 Norwood Palliation For The Treatment Of Single Ventricle Heart Disease, Tianqi Hang

All Dissertations

Hypoplastic left heart syndrome (HLHS) is a congenital heart defect in which the left ventricle is severely underdeveloped. The Norwood procedure is the first stage procedure to make an unrestrictive systemic blood flow and at the same time balance it with the pulmonary flow. This is done by constructing a neo-aorta using the pulmonary artery root and the autologous aorta, and then installing a shunt to the pulmonary artery. Variations of the Norwood surgery include the modified Blalock-Taussig (mBT) shunt, which diverts blood from the innominate artery to the pulmonary artery (PA), and the Right Ventricle Shunt (RVS), which diverts …

Electromechanical Modeling Of A Honeycomb Core Integrated Vibration Energy Converter With Increased Specific Power For Energy Harvesting Applications, Nataraj Chandrasekharan

All Dissertations

Innovation in integrated circuit technology along with improved manufacturing processes has resulted in considerable reduction in power consumption of electromechanical devices. Majority of these devices are currently powered by batteries. However, the issues posed by batteries, including the need for frequent battery recharge/replacement has resulted in a compelling need for alternate energy to achieve self-sufficient device operation or to supplement battery power. Vibration based energy harvesting methods through piezoelectric transduction provides with a promising potential towards replacing or supplementing battery power source. However, current piezoelectric energy harvesters generate low specific power (power-to-weight ratio) when compared to batteries that the harvesters …

Characterizing The Effective Bandwidth Of Nonlinear Vibratory Energy Harvesters Possessing Multiple Stable Equilibria, Meghashyam Panyam Mohan Ram

All Dissertations

In the last few years, advances in micro-fabrication technologies have lead to the development of low-power electronic devices spanning critical fields related to sensing, data transmission, and medical implants. Unfortunately, effective utilization of these devices is currently hindered by their reliance on batteries. In many of these applications, batteries may not be a viable choice as they have a fixed storage capacity and need to be constantly replaced or recharged. In light of such challenges, several novel concepts for micro-power generation have been recently introduced to harness, otherwise, wasted ambient energy from the environment and maintain these low-power devices. Vibratory …

On Subgrid-Scale Physics In The Convective Atmospheric Surface Layer, Khuong Nguyen

All Dissertations

The dynamics of the subgrid-scale (SGS) stress and scalar flux in the convective atmospheric surface layer are studied using field measurements from the Advection Horizontal Array Turbulence Study (AHATS). We extend the array technique previously used to evaluate the SGS velocity and temperature to include measurements of the fluctuating pressure, enabling separation of the resolvable- and subgrid-scale pressure and allowing for the first-ever observations of the pressure covariance terms and the full SGS budgets. Non-dimensional forms of the budget terms are analysed as functions of the surface-layer stability parameter and the ratio of the wavelength of the spectral peak of …

Impact Of Constructing A Low Crested Weir In Cape Canaveral On Flushing In The Banana River, Atousa Saberi

Theses and Dissertations

The purpose of this study is to determine the extent to which constructing a low crested weir adjacent to Port Canaveral improves ushing in the Banana River. The Banana River is a 50 km long sub-basin of Indian River Lagoon (IRL), located between Cape Canaveral and Merritt Island in Brevard County. Although Port Canaveral locks connect the Banana River to the ocean, the locks remain closed when there are no passing vessels; therefore, it has limited circulation and a long ushing time. Declining water quality can be linked to recent high mortality events of di erent species living in the …

Predicted Stresses In A Ball-Grid-Array (Bga)/Column-Grid-Array (Cga) Assembly With A Low Modulus Solder At Its Ends, Ephraim Suhir, Reza Ghaffarian

Mechanical and Materials Engineering Faculty Publications and Presentations

A simple, easy-to-use and physically meaningful predictive model is suggested for the assessment of thermal stresses in a ball-grid-array or a column-grid-array with a low modulus solder material at the peripheral portions of the assembly. It is shown that the application of such a design can lead to a considerable relief in the interfacial stresses, even to an extent that inelastic strains in the solder joints could be avoided. If this happens, the fatigue strength of the bond and of the assembly as a whole will be improved dramatically: low-cycle fatigue conditions will be replaced by the elastic fatigue condition, …

An Approach To Model Plastic Deformation Of Metallic Plates In Hypervelocity Impact Experiments, Shawoon Kumar Roy

UNLV Theses, Dissertations, Professional Papers, and Capstones

Space structures are subjected to micro-meteorite impact at extremely high velocities of several kilometers per second. Similarly, design of military equipment requires understanding of material behavior under extremely high pressure and temperature. Study of material behavior under hypervelocity impact (HVI) poses many challenges since few researchers so far have approached this problem. Material models, equations of the state, and fracture mechanics are not well understood under these conditions.

The objective of this research is to present an approach for studying plastic deformation of metallic plates under HVI conditions. A two-stage light gas gun can be used to simulate these conditions …

The Comparison Of Two Supine Manikins And The Use Of A Shock And Vibration Isolation System For Litter Patients In Air Medical Transport, Karina Karlui Saenz Acosta

UNLV Theses, Dissertations, Professional Papers, and Capstones

Studies show that repeated shock and vibration during aero medical and ground transport are causing patient pain and may be adversely affecting patients’ medical outcome. Patients with spine and head injuries and other severe neurological injuries are the most vulnerable to repeated shock and vibration exposure caused by the vehicle. It is crucial to minimize the effects of these forces on patients during air and ground medical transport. The development of new medical evacuation platforms creates a need to better understand the effects of human exposure to shock and vibration. The use of human subjects to measure whole body vibration …

Numerical Validation Of Cooling Performance Of Phase Change Materials Integrated Into Heat Sinks For Electronics Cooling, Shaimaa Mohamed Abu Ayyan

Theses

This study aims to analyze the cooling performance of phase change materials (PCMs) integrated into metallic heat sinks (HSs) both experimentally and numerically. For the experimental part of the study, a test setup has been constructed to test PCM integrated heat sinks. The heat sinks are prepared as metallic containments having fins with fixed inter-fin spacing. The volume between the heat sink fins is filled with PCM namely: a paraffin wax, salt hydrate-calcium chloride and milk-fat, then the whole system is sealed for testing under various heat loads at 4W, 6W, 8W and 10W. Four modes of operation are experimentally …

Designing, Building And Testing A Solar Thermoelectric Generation, Steg, For Energy Delivery To Remote Residential Areas In Developing Regions, Yacouba Moumouni

UNLV Theses, Dissertations, Professional Papers, and Capstones

New alternatives and inventive renewable energy techniques which encompass both generation and power management solutions are fundamental for meeting remote residential energy supply and demand today, especially if the grid is quasi-inexistent. Solar thermoelectric generators can be a cost-effective alternative to photovoltaics for a remote residential household power supply. A complete solar thermoelectric energy harvesting system is presented for energy delivery to remote residential areas in developing regions. To this end, the entire system was built, modeled, and then validated with LTspice simulator software via thermal-to-electrical analogy schemes. Valuable data in conjunction with two novel LTspice circuits were obtained, showing …

Microstructure Alone Induced Wetting Transition From Hydrophilic To Hydrophobic On Silicon And Graphene, Henry L. Ems

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

In the present work, transition from hydrophilic to hydrophobic wetting states for an intrinsically hydrophilic surface (contact angle less than 45 degrees) using only surface microstructuring is presented. The surface microstructures are re-entrant microcavities (inverted trapezoidal microstructures) which promote air entrapment below the water droplet causing a Cassie wetting state as opposed to a Wenzel state where the surface is completely wetted. The microstructures were fabricated on a Silicon-On-Insulator (SOI) wafer through steps of deposition, photolithography, etching, and bonding. Contact angle measurements demonstrated the ability of the microfabricated surfaces to sustain large contact angles above 100°, in comparison to a …

Simulation Of An Air Cooled Single-Effect Solar Absorption Cooling System With Evacuated Tube Collectors, Mohsen Jahandardoost

UNLV Theses, Dissertations, Professional Papers, and Capstones

Consistently increasing CO2 emission and ozone depletion from synthetic refrigerants are serious environmental issues challenging the scientific community. Absorption cooling systems give scope of utilizing low grade energy source for generating cooling effect. Solar energy is one of these low grade energy sources and with considering the fact that cooling demand increases with the intensity of solar radiation, solar refrigeration has been considered as a logical solution.

This thesis consists of two different simulation stages, in the first stage, a single effect lithium bromide absorption cooling system with constant cooling capacity is modeled and the effect of ambient and generator …

Sound Attenuation Of Fiberglass Lined Ventilation Ducts, Jacob Albright

UNLV Theses, Dissertations, Professional Papers, and Capstones

Sound attenuation is a crucial part of designing any HVAC system. Most ventilation systems are designed to be in areas occupied by one or more persons. If these systems do not adequately attenuate the sound of the supply fan, compressor, or any other source of sound, the affected area could be subject to an array of problems ranging from an annoying hum to a deafening howl. The goals of this project are to quantify the sound attenuation properties of fiberglass duct liner and to perform a regression analysis to develop equations to predict insertion loss values for both rectangular and …

Application Of The Aeroacoustic Analogy To A Shrouded, Subsonic, Radial Fan., Bryan Buccieri

Electronic Theses and Dissertations

A study was conducted to investigate the predictive capability of computational aeroacoustics with respect to a shrouded, subsonic, radial fan. A three dimensional unsteady fluid dynamics simulation was conducted to produce aerodynamic data used as the acoustic source for an aeroacoustics simulation. Two acoustic models were developed: one modeling the forces on the rotating fan blades as a set of rotating dipoles located at the center of mass of each fan blade and one modeling the forces on the stationary fan shroud as a field of distributed stationary dipoles. Predicted acoustic response was compared to experimental data. The blade source …

Evaluation Of Two-Phase Evaporation Pressure Drop Correlations For Low Refrigerant Mass Flux., Anna Fenko

Electronic Theses and Dissertations

This study was conducted to evaluate three currently popular two-phase pressure drop models for extremely low velocity refrigerant flow through smooth circular evaporators in household refrigeration systems. Experimental data was taken at mass fluxes under 70 kg/m²s for two refrigerants, R134A and R600A, internal diameters of aluminum evaporators ranging from 0.186 to 0.317 inches, U-bend internal radii ranging from 0.342 to 0.750 inches in horizontal and vertical orientations of evaporators. The geometry of the samples closely resembled a commonly used serpentine shape with multiple U-bends experiencing both, up- and down-flow of the refrigerant. Two empirical models, Müller-Steinhagen & …

Implementing A Linear Quadratic Spacecraft Attitude Control System, Daniel Kolosa

Masters Theses

This thesis implements a linear quadratic attitude control system for a low-thrust spacecraft. The goal is to maintain spacecraft alignment with a time-varying thrust vector needed for trajectory change maneuvers. A linear quadratic attitude control approach is used to maintain spacecraft pointing throughout flight. This attitude control strategy uses the thrust-acceleration input obtained from a linear quadratic optimal trajectory control model that simulates the trajectory of a spacecraft in orbit maneuvers. This attitude model simulates a CubeSat, a small satellite that is equipped with a low-thrust propulsion and attitude control system. An orbit raising and a plane change scenario is …

Resistance Prediction For Asymmetrical Configurations Of High-Speed Catamaran Hull Forms, Srikanth Asapana

Theses and Dissertations

Predicting the resistance of a high-speed catamaran has been of interest to naval architects for the last three decades. Even though considerable amount of research has been carried out in this area, there remains a degree of uncertainty in the accurate resistance prediction of catamaran hull forms in the early design stage. Researches carried out so far have generally ignored the resistance characteristics of unconventional and unsymmetrical catamaran hull forms. This thesis attempts to undertake a comparative analysis of resistance characteristics between newly developed unconventional catamaran hull forms of different configurations derived from existing conventional NPL series of round bilge …

Comparative Estimates Of Anthropogenic Heat Emission In Relation To Surface Energy Balance Of A Subtropical Urban Neighborhood, Changhyoun Park, Gunnar W. Schade, Nicholas D. Werner, David J. Sailor, Cheolhee Kim

Mechanical and Materials Engineering Faculty Publications and Presentations

Long-term eddy covariance measurements have been conducted in a subtropical urban area, an older neighborhood north of downtown Houston. The measured net radiation (Q*), sensible heat flux (H) and latent heat flux (LE) showed typical seasonal diurnal variations in urban areas: highest in summer; lowest in winter. From an analysis of a subset of the first two years of measurements, we find that approximately 42% of Q* is converted into H, and 22% into LE during daytime. The local anthropogenic heat emissions were estimated conventionally using the long-term residual method and the heat emission inventory approach. We also …

A Proposed Integrated Data Collection, Analysis And Sharing Platform For Impact Evaluation, Andreas Kipt, Waylon Brunette, Jordon Kellerstrass, Matthew Podolsky, Javier Rosa, Mitchell Sundt, Daniel Wilson, Gaetano Borriello, Eric Brewer, Evan A. Thomas

Mechanical and Materials Engineering Faculty Publications and Presentations

Global poverty reduction efforts value monitoring and evaluation, but often struggle to translate lessons learned from one intervention into practical application in another intervention. Commonly, data is not easily or often shared between interventions and summary data collected as part of an impact evaluation is often not available until after the intervention is complete. Equally limiting, the workflows that lead to research results are rarely published in a reproducible, reusable, and easy-to-understand fashion for others. Information and communication technologies widely used in commercial and government pro- grams are growing in relevance for international global development professionals and offer a potential …

Biomechanical Performances Of Networked Polyethylene Glycol Diacrylate: Effect Of Photoinitiator Concentration, Temperature, And Incubation Time, Morshed Khandaker, Albert Orock, Stefano Tarantini, Jeremiah White, Ozlem Yasar

Publications and Research

Nutrient conduit networks can be introduced within the Polyethylene Glycol Diacrylate (PEGDA) tissue construct to enable cells to survive in the scaffold. Nutrient conduit networks can be created on PEGDA by macrochannel to nanochannel fabrication techniques. Such networks can influence the mechanical and cell activities of PEGDA scaffold. There is no study conducted to evaluate the effect of nutrient conduit networks on the maximum tensile stress and cell activities of the tissue scaffold.The study aimed to explore the influence of the network architecture on the maximum tensile stress of PEGDA scaffold and compared with the nonnetworked PEGDA scaffold. Our study …

Configuration Management In Manufacturing And Assembly: Case Study And Enabler Development, Keith Phelan

All Dissertations

The overall goal of this research is to improve the product configuration change management process. The increase in the demand for highly customizable products has led to many manufacturers using mass customization to meet the constantly changing demands of a wide consumer base. However, effectively managing the configurations can be difficult, especially in large manufacturers or for complex products with a large number of possible configurations. This is largely due to a combination of the scope of the configuration management system and the difficulty in understanding how changes to one element of a configuration can propagate through the configuration system. …

Effect Of Nano-Oxide Particle Size On Radiation Resistance Of Ironechromium Alloys, Weizong Xu, Lulu Li, James A. Valdez, Mostafa Saber, Yuntian Zhu, Carl C. Koch, Ronald O. Scattergood

Mechanical and Materials Engineering Faculty Publications and Presentations

Radiation resistance of Fe-14Cr alloys under 200 keV He irradiation at 500 ­*C was systematically investigated with varying sizes of nano oxide Zr, Hf and Cr particles. It is found that these nano oxide particles acted as effective sites for He bubble formation. By statistically analyzing 700-1500 He bubbles at the depth of about 150-700 nm from a series of HRTEM images for each sample, we established the variation of average He bubble size, He bubble density, and swelling percentage along the depth, and found them to be consistent with the He concentration profile calculated from the SIRM program. Oxide …