Mechanical Engineering Commons^™

Test 2148a: New Holland T8.380 Smartrax, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1060 Massey Ferguson 7715, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1055 New Holland T7.290, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1053 Case-Ih Optum 270 Cvx, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1027a Massey Ferguson 7722s, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1062a Massey Ferguson 7716s, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1071 Challenger Mt545e, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1066 Challenger Mt525e, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1058a Massey Ferguson 7715s, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1127 Challenger Mt495e, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

In Situ Microscopy Of The Self-Assembly Of Branched Nanocrystals In Solution, Eli Sutter, Peter Sutter, Alexei V. Tkachenko, Roman Krahne, Joost De Graaf, Milena Arciniegas, Liberato Manna

Department of Mechanical and Materials Engineering: Faculty Publications

Solution-phase self-assembly of nanocrystals into mesoscale structures is a promising strategy for constructing functional materials from nanoscale components. Liquid environments are key to self-assembly since they allow suspended nanocrystals to diffuse and interact freely, but they also complicate experiments. Real-time observations with single-particle resolution could have transformative impact on our understanding of nanocrystal self-assembly. Here we use real-time in situ imaging by liquid-cell electron microscopy to elucidate the nucleation and growth mechanism and properties of linear chains of octapod-shaped nanocrystals in their native solution environment. Statistical mechanics modelling based on these observations and using the measured chain-length distribution clarifies the …

Influence Of Shear Stress Magnitude And Direction On Atherosclerotic Plaque Composition, Ryan M. Pedrigi, Vikram V. Mehta, Sandra M. Bovens, Zahra Mohri, Christian Bo Poulsen, Willy Gsell, Jordi L. Tremoleda, Leila Towhidi, Ranil De Silva, Enrico Petretto, Rob Krams

Department of Mechanical and Materials Engineering: Faculty Publications

The precise flow characteristics that promote different atherosclerotic plaque types remain unclear. We previously developed a blood flow-modifying cuff for ApoE^−/− mice that induces the development of advanced plaques with vulnerable and stable features upstream and downstream of the cuff, respectively. Herein, we sought to test the hypothesis that changes in flow magnitude promote formation of the upstream (vulnerable) plaque, whereas altered flow direction is important for development of the downstream (stable) plaque. We instrumented ApoE^−/− mice (n=7) with a cuff around the left carotid artery and imaged them with micro-CT (39.6 μm resolution) eight to nine weeks …

Experimental Strain Measurement In Ultrasonic Welding Of Battery Tabs, Chen Chen

Wayne State University Theses

Lithium-ion battery is one the most popular types of batteries currently used in electric

vehicles. To meet the power requirement, hundreds of Lithium ion battery cells are connected together before being assembled into a battery pack. Ultrasonic welding is the most widely used joining technology to connect battery cells together. In an ultrasonic welding process, high frequency oscillation is used to generate small relative motions between sheet metals to be welded, and produce solid-state bonds between the sheet metals clamped under pressure. One of the major issues for battery pack ultrasonic welding is that sometimes the welding process damages the …

Modeling Fluid Interactions With Granular And Fibrous Surfaces, Mana Mokhtabad Amrei

Theses and Dissertations

Understanding the interactions between a body of liquid and a curvy surface is important for many applications such as underwater drag force reduction, droplet filtration, self-cleaning, and fog harvesting, among many others. This study investigates ways to predict the performance of granular and fibrous surfaces for some of the above applications. More specifically, our study is focused on 1) modeling the mechanical stability of the air-water interface over submerged superhydrophobic (SHP) surfaces and their expected drag reduction benefits, and 2) predicting the mechanical stability of a droplet on a fiber in the presence of an external body force. For the …

Shear Driven Suppressed Nucleation Annular Flow-Boiling In Millimeter-Scale Channels: Direct Numerical Simulations, Sharayu Bhasme

Dissertations, Master's Theses and Master's Reports

Many contemporary high heat-flux cooling applications are facilitated by mm-scale flow-boilers that operate in the steady annular suppressed nucleation regime (i.e., a thin evaporating liquid film flow covers the heated boiling-surface).

For such cases, this thesis presents a direct numerical simulation (DNS) approach. The steady algorithm and its accuracy are discussed. Representative detailed solutions for annular flow-boiling of FC-72 in a horizontal channel are presented.

Mechanical Testing Of Fused Filament 3-D Printed Components For Distributed Manufacturing, Nagendra Gautam Tanikella

Dissertations, Master's Theses and Master's Reports

Fused filament fabrication (FFF)-based open-source 3-D printers offer the potential of decentralized manufacturing both in developing and developed countries. Unfortunately, a severe lack of data and standards relating to material properties and printed components limit this potential. This thesis first investigates the mechanical properties of a wide-range of FFF materials and provides a database of mechanical strength of the materials tested. The results demonstrate that the tensile strength of a 3-D printed specimen depends largely on the mass of the specimen, which provides a means to estimate the strength of 3-D printed components. Then this information is used to evaluate …

Technical Feasibility Analysis Of Utilizing Special Purpose Machine Tools, Ana Vafadar, Majid Tolouei Rad, Kevin Hayward, Kazem Abhary

Research outputs 2014 to 2021

Special purpose machine tools (SPMs) are primarily used for performing drilling-related operations and are widely used in mass production including automotive component manufacturing. Utilization of SPM is considerably widespread; however, this technology is relatively new and expensive. The important problems facing manufacturing industries wishing to utilize this technology is feasibility analysis to decide whether a SPM can be utilised for production of the given part and if it is feasible which SPM components would be appropriate. Since the cost of utilizing SPM is high, feasibility analysis must be performed before any investment on detailed design. This paper proposes a technical …

Optimization-Based Path Planning For Separation Assurance On Small Unmanned Aircraft, Matthew Duffield, Andrew Ning, Timothy Mclain

Faculty Publications

This paper presents a time-based path planning optimizer for separation assurance for unmanned aircraft systems (UAS). Given Automatic Dependent Surveillance-Broadcast (ADS-B) as a sensor, intruder information such as position, velocity, and identification information is available at ranges on the order of 50 nautical miles. Such long-range intruder detection facilitates path planning for separation assurance, but also poses computational challenges. The time-based path optimizer presented in this paper provides a path-planning method that takes advantage of long-range ADS-B information and addresses the associated challenges. It is capable of long-range path planning and, due to the convex formulation, is computationally efficient enough …

Parameterized Vertical-Axis Wind Turbine Wake Model Using Cfd Vorticity Data, Andrew Ning, Eric Tingey

Faculty Publications

In order to analyze or optimize a wind farm layout, reduced-order wake models are often used to estimate the interactions between turbines. While many such models exist for horizontal-axis wind turbines, for vertical-axis wind turbines (VAWTs) a simple parametric wake model does not exist. Using computational fluid dynamic (CFD) simulations we computed vorticity in a VAWT wake, and parameterized the data based on normalized downstream positions, tip-speed ratio, and solidity to predict a normalized wake velocity deficit. When compared to CFD, which takes about a day to run one simulation, the reduced-order model predicts the velocity deficit at any location …

Compound Joints: Behavior And Benefits Of Flexure Arrays, Larry L. Howell, Ezekiel G. Merriam, Jason M. Lund

Faculty Publications

Because compliant mechanisms achieve their motion through deflection of flexible members, they have a limited range of motion and finite stiffness. Many common flexure geometries also suffer from a non-stationary center of rotation. These properties can be obstacles to their adoption in applications that require large displacements, low stiffness, or stationary centers of rotation. This work presents the concept of compound flexures: by assembling arrays of flexures, we can increase range of motion, decrease stiffness, and reduce center shift. We first develop the theory behind some of the basic behavior of compound joints. Then finite element analysis is used to …

Facilitating Deployable Mechanisms And Structures Via Developable Lamina Emergent Arrays, Larry L. Howell, Robert J. Lang, Spencer P. Magleby, Todd G. Nelson, Nathan A. Pherson

Faculty Publications

A method is presented utilizing networks of lamina emergent joints, known as lamina emergent arrays, to accommodate large-curvature developable structures suited to deployable applications. By exploiting the ruling lines in developable surfaces, this method enables developable structures and mechanisms that can be manufactured with two-dimensional geometry and yet have a greater range of elastic motion than is possible with a solid sheet of material. Aligning the joints to the ruling lines also biases the structure to a specific deployment path. A mathematical model is developed to describe the resulting stiffness of the structure employing the lamina emergent arrays and equations …

Constructal Alkaline Membrane Fuel Cell (Amfc) Design, E. M. Sommer, J. V. C. Vargas, Lauber De Souza Martins, J. C. Ordonez

Faculty Publications

This paper introduces a structured procedure to optimize the internal structure (relative sizes, spacing) and external shape (aspect ratios) of a single alkaline membrane fuel cell so that net power is maximized. The optimization of flow geometry is conducted for the smallest (elemental) level of a fuel cell stack, i.e., the single alkaline membrane fuel cell, which is modeled as a unidirectional flow system. The polarization curve, total and net power, and efficiency are obtained as functions of temperature, pressure, electrolyte solution concentration (KOH), geometry and operating parameters. The optimization is subjected to fixed total volume. There are two levels …

Ultra-Thin Microfluidic Devices Built Via Thermal Lamination, Fernando Ontiveros, J Ryan Mcdowell

Biology Faculty/Staff Publications

Widespread adoption of lab-on-a-chip technologies may be encouraged by the development of methods and devices that require minimal investment and expertise. Here we describe a type of device that makes exclusive use of consumer-grade components and equipment. The devices consist of as little as three layers of a polymer film, with microchannels shaped by an inexpensive craft cutter, and sealed by thermal lamination. Fabrication time is in the order of minutes, and the method does not require any prior training. To showcase the properties and demonstrate the versatility of the devices, we describe their use to generate fully biocompatible lipid-based …

Techno-Economic Feasibility Of Distributed Torrefaction Systems Using Corn Stover Feedstock, Evan Almberg

Electronic Theses and Dissertations

This study investigated the economic feasibility of distributed torrefaction biorefining systems using corn stover feedstock to generate value-­‐added products. Distributed torrefaction systems have the potential to operate on private agricultural enterprises as well as community-­‐scale processing facilities, similar in scale to local grain elevators. Distributed systems will thus, reduce the need for large capital investments for dedicated commercial biorefining facilities and decrease logistical concerns for harvesting and marketing the torrefied corn stover products. In this study, a techno-­‐economic model was developed to analyze the economics of harvesting techniques, logistics, processing requirements, and end product utilization. Results were determined using baseline …

A Study Of The Mechanical Behavior Of Composite Materials Exposed To Corrosive Environments, Ryan Keith Hedgepeth

Electronic Theses and Dissertations

A collaborative study was conducted to examine the degradation of commercially pultruded uni-directional e-glass composites. The case study specimens, including a variety of commercially pultruded polyester/e-glass and vinylester/e-glass composites were exposed to corrosive environments, namely: distilled water (h2o), bleach (naclo), and hydrochloric acid (hcl) for a minimum of 60 days, and the degradation was analyzed. Such a study was chosen on two accounts, 1) to contribute viable data to industry and research and 2) to provide data to be used to develop a standardized practice to characterize the durability for pultruded composites used for structural applications. A control group was …

Quantum Yield Optimization For Semiconductor Photocatalysis Systems, Ryan Catabay

Maseeh Summer Undergraduate Research Experience

The utilization of photocatalysis has a well-known potential for mineralizing organic contaminants in water purification processes. A continuous flow photocatalytic reactor was developed in order to test the quantum yield of titanium dioxide, a semiconductor material well known for its photocatalytic properties. In order to build this reactor, multiple manufacturing methods were performed: manual and CNC machining, laser cutting, waterjet cutting, and chemical synthesis. A continuous flow reactor was particularly designed for a controlled, variable radiant flux of ultraviolet light. This continuous UV radiation excites the photocatalyst, generating electron hole pairs that form hydroxyl radicals, which in turn mineralize organic …

An Experimental Investigation On The Effect Of Intake Charge Temperature And Injection Timing On Autoignition Of Low Cetane Number Fuel (Sasol Ipk), Swapnil Shekhar Bodele

Wayne State University Theses

ABSTRACT

AN EXPERIMENTAL INVESTIGATION ON THE EFFECT OF

INTAKE CHARGE TEMPERATURE AND INJECTION TIMING

ON AUTOIGNITION OF LOW CETANE NUMBER FUEL

(SASOL IPK)

by

SWAPNIL S BODELE

May 2016

Advisor: Dr. Naeim Henein

Major: Mechanical Engineering

Degree: Master of Science

Although diesel engines are considered the best powerhouses for their heavy-duty

capabilities, concerns have been raised because of their emission issues. Alternative

fuels like jet fuels can be substitute to them for improved efficiencies. The Department Of

Defense uses JP8 for their combat vehicles under their Single Fuel Concept for a better

logistic supply chain. However, due to the projected …

Nebraska Summary: S1016 Massey Ferguson 7720, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1015 Massey Ferguson 7719, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary 1020: Challenger Mt555e, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …