Mechanical Engineering Commons^™

Utilizing Tunable Signal Interference Control Topologies With Electromechanical Resonators, Bryce A. Geesey

Open Access Theses

Exploiting knowledge gained from previous investigations of channelized and trans-versal filters, signal interference filters use transmission line differences to generate transmission zeros through phase-shifted combinations of signals at the output of a device. The transmission lines used in these circuits are straightforward to design, but are limited to high-frequency signals (on the order of a few gigahertz) due to the necessity for spatial compactness and low loss. More recent studies have used electromechanical resonators to achieve phase shifting and quality factor improvements at slightly-lower frequencies. These concepts may prove useful if extended to micro- and nanoscale resonators.

To explore signal …

The Effect Of Confinement On The Development Of An Axisymmetric Wall Jet In Confined Jet Impingement, Tianqi Guo

Open Access Theses

Impinging jets have been widely used in the industry for cooling, heating, drying and many other purposes due to their excellent level of mass and heat transfer capacities. When issued into a confinement gap fully filled with working liquid, which is a typical configuration for the compact cooling devices designed to handle the extremely high heat fluxes generated by continuously working electronic components, they are classified as submerged confined impingement jets. Though the complicated flow field induced by the jet has attracted enormous amount of research efforts from heat transfer as well as fluid dynamics points of view, many key …

Mixed Mesh/Nodal Magnetic Equivalent Circuit Modeling Of A Six-Phase Claw-Pole Automotive Alternator, Daniel C. Horvath

Open Access Theses

Magnetic equivalent circuits (MECs) have been employed by many researchers to model the relationship between magnetic flux and current in electromagnetic systems such as electric machines, transformers and inductors [1] ,[2]. Magnetic circuits are analogous to electric circuits where voltage, current, resistance and conductance are the respective counterparts of magneto-motive force (MMF), magnetic flux, reluctance and permeance. The solution of MECs can be accomplished with the plethora of techniques developed for electrical circuit analysis. Specifically, mesh analysis, based on Kirchoff’s Voltage Law (KVL), and nodal analysis, based on Kirchoffs Current Law (KCL), are two very common solution techniques. Once an …

Modifications To Johanson's Roll Compaction Model For Improved Relative Density Predictions, Yu Liu

Open Access Theses

Johanson’s roll compaction model [J.R. Johanson, A rolling theory for granular solids, ASME Journal of Applied Mechanics E32 (1965) 842–848] is modified to improve its predictions of a compacted ribbon’s relative density. Previous work has shown that the maximum roll pressure and ribbon relative density predicted by the Johanson model are not only larger than those predicted from finite element method (FEM) simulations, but also unphysical in some cases. This over-prediction is due to a one-dimensional flow assumption in the Johanson model. Real powder velocity profiles within a roll compactor are non-uniform.

Johanson’s analysis is modified in this work to …

Capacity Optimization Of Battery-Generator Hybrid Power System: Toward Minimizing Maintenance Cost In Expeditionary Basecamp/Operational Energy Applications, Jude C. Onwuanumkpe

Open Access Theses

Low and transient load condition are known to have deleterious impact on the efficiency and health of diesel generators (DGs). Extensive operation under such loads reduces fuel consumption and energy conversion efficiency, and contribute to diesel engine degradation, damage, or catastrophic failure. Non-ideal loads are prevalent in expeditionary base camps that support contingency operations in austere environments or remote locations where grid electricity is either non-existent or inaccessible. The impact of such loads on DGs exacerbates already overburdened basecamp energy logistics requirements. There is a need, therefore, to eliminate or prevent the occurrence of non-ideal loads. Although advances in diesel …

Analysis Of Body Force Effects On Flow Boiling And Condensation With Finite Inlet Quality, Lucas E. O'Neill

Open Access Theses

This study explores flow boiling pressure drop of FC-72 in a rectangular channel subjected to single-side and double-sided heating for vertical upflow, vertical downflow, and horizontal flow with positive inlet quality. Analysis of temporal records of pressure transducer signals is used to assess the influences of orientation, mass velocity, inlet quality, heat flux, and single-sided versus double-sided heating on magnitude of pressure drop oscillations, while fast Fourier transforms of the same records are used to capture dominant frequencies of oscillations. Time-averaged pressure drop results are also presented, with trends focusing on the competing influences of body force and flow inertia, …

Secondary Atomization Of Inelastic Non-Newtonian Liquid Drops In The Bag And Multimode Regimes, Jonathan Rocha

Open Access Theses

Secondary atomization of inelastic shear thinning non-Newtonian liquids in the bag and multimode regimes was studied. Six mixtures were formulated from deionized (DI) water, Avantor Performance Materials' USP grade 100% vegetable based glycerin, and Ashland's Carboxymethylcellulose (CMC-7MF or CMC-7HF). The resulting solutions had power law parameters flow behavior index, n, between 0.71 and 0.93 and consistency index, K, in the range of 0.0464 to 0.37 Pa·s n. The effective viscosity for each mixture was estimated using the power-law model and experimentally measured strain rates up to the initiation time.

Secondary atomization was achieved using a continuous jet setup. Breakup events …

Transportation And Power Solutions For Africa: The Assessment And Optimization Of The Purdue Utility Platform, Jeremy Patrick Robison

Open Access Theses

The Purdue Utility Platform (PUP) is an off-road utility vehicle that was created to improve agricultural productivity in sub-Saharan Africa by providing appropriate transportation and mobile power solutions. The vehicle design has matured to a level where it now requires more robust engineering tools to perform a rigorous assessment of its function. The assessment will be pursued in two areas: durability of the frame and the roll stability of the vehicle. To assess the durability of the frame, a data acquisition system was installed to collect strain gauge information during the vehicle’s operation. This data was then related to an …

Ultra-Thin Boron Nitride Films By Pulsed Laser Deposition: Plasma Diagnostics, Synthesis, And Device Transport, Nicholas Robert Glavin

Open Access Dissertations

This work describes, for the first time, a pulsed laser deposition (PLD) technique for growth of large area, stoichiometric ultra-thin hexagonal and amorphous boron nitride for next generation 2D material electronics. The growth of boron nitride, in this case, is driven by the high kinetic energies and chemical reactivities of the condensing species formed from physical vapor deposition (PVD) processes, which can facilitate growth over large areas and at reduced substrate temperatures. The use of optical emission spectroscopy during plasma growth provides insight into chemistry, kinetic energies, time of flight data, and spatial distributions within a PVD plasma plume ablated …

Characterization Of Pool Boiling Heat Transfer From Porous-Coating-Enhanced Surfaces, Suchismita Sarangi

Open Access Dissertations

Development of techniques for enhancement and optimization of thermal management technologies has been a highly active area of research in recent decades in response to the rapid emergence of compact, high-power electronic systems. Immersion cooling by boiling is one of the preferred methods for high power density applications, due to its passive nature and high heat transfer coefficients obtained. Pool boiling heat transfer has been extensively studied in recent decades to understand the inherent mechanisms yielding the high heat transfer rates, as well as to further enhance the heat transfer by simple modifications or additions to existing approaches. This thesis …

Drag Reduction Using Femtosecond Laser Surface Processing: Experimental Setup, Derek Wallin, Henry Ems, Craig Zuhlke, Dennis R. Alexander, George Gogos, Sidy Ndao

UCARE: Research Products

The experimental setup for developing a system to test the drag effects of different superhydrophorbicities. This is used to revise the current Moody Chart and redefine fluid drag in a pipe.

Fluid drag reduction is important in many applications such as reducing the power requirement to pump a fluid through a channel or pipe. The Center for Electro-Optics and Functionalized Surfaces (CEFS) at the University of Nebraska – Lincoln uses a femtosecond laser to functionalize 304 stainless Steel to become superhydrophilic or superhydrophobic The Processing produces microscale and nanoscale surface roughness that when treated with siloxanes becomes superhydrophobic. Small vortices …

Development Of A Robust Setup For The Study Of Wetting Characteristics Of Low Melting Point Metals, John D. Casias, Ethan Allan Davis, Sidy Ndao

UCARE: Research Products

• Energy use is very inefficient

• Approx. 60% rejected mostly in the form of waste heat

• Low melting point metals are promising for applications in thermal energy management, conversion, and storage

A Preliminary Study Of The Relationship Between Complexity, Motivation, And Design Quality., Philip John Mountain

Electronic Theses and Dissertations

This collection of work comprises a preliminary study of the relationships between product complexity, design motivation, and design quality. Complexity, as it relates to the design process, is largely undefined and there exists no generally accepted method of measurement. This study applies an independent data set to a complexity measurement technique and develops complexity measurements at the pre and post design stages. Pre design is considered when design ideas are in formation and customer needs are being addressed. Post design is considered when a functional prototype is realized, manufacturing and assembly processes have been considered, and the product design is …

Model And Control Development Of Hybrid Fuel Cell And Battery Power System For Uas (Quadcopter), Mohammad Biswas

Faculty Posters

This poster was presented during the UT Tyler Faculty Research Poster Showcase 2016.

Design And Prototyping Of A Variable Geometry Extrusion Die To Exhibit Significant Alteration Of Shape, David C. Bell

Honors Theses

Extruded parts are conventionally made by forcing melted plastic through a steel die having a fixed opening that matches the shape of the part. Plastic parts made by extrusion include weather stripping, PVC pipe, and composite lumber. Variable geometry dies can change their opening shape during the extrusion process. Developing shape-changing dies technology offers the possibility of making parts with varying cross-sections that currently need to be made through injection molding. This is desirable as, compared to molding, extrusion tends to be faster and less expensive. Variable geometry extrusion dies have been designed and prototyped by the University of Dayton …

Nonlinear Analysis Of Balance Data In The Easter Seals Adult Day Services Population, Taylor Marie Schemmel

Honors Theses

81.1 million adults are expected to be affected by dementia in 2040. Individuals with dementia are twice as likely to fall as healthy individuals and three times as likely to sustain an injury during a fall. Unfortunately, current fall prevention techniques in place for cognitively healthy older adults are not as effective for those with dementia. The objective of this study was to examine balance differences between individuals of varying cognitive ability utilizing Easter Seals Adult Day Services. All study participants completed the Montreal Cognitive Assessment (MoCA). Clinical assessments were done in conjunction with static posturography data collection on a …

Phosphorus Adsorption Through Engineered Biochars Produced From Local Waste Products, Peter Ogonek

Honors Theses

Phosphorus contained in agricultural runoff is a major anthropogenic contributor to harmful algal blooms (HABs). Biochars are carbon-based materials produced from the pyrolysis of waste biomass that have the potential to amend soils and remediate inorganic and organic contaminants from water. Engineered biochars tailored to adsorb phosphorus from water could reduce the availability of the nutrient in agricultural runoff, reducing the size and frequency of HABs. This study observed the phosphorus adsorption properties of engineered biochars produced from two source materials, oak sawdust and cornstalk residue, and being unmodified, acid-rinsed, or loaded with magnesium prior to pyrolysis, creating acid-rinsed, unmodified, …

A Hybrid Position Feedback Controller For Bistable Structures, Mehmet R. Simsek

Mechanical & Aerospace Engineering Theses & Dissertations

Bistability is the property of structures showing the ability to attain two statically stable states. Due to dynamic and static advantages such as no energy demand at stable positions and providing higher deflections compared to a monostable structure, bistability may be appealing in control surface design for aircraft structures and load alleviation for wind turbine blades. The dynamics of bistable structures is nonlinear because of the snap-through occurring during the cross-well oscillation between two stable states. A new control strategy called hybrid position feedback control is developed based on the conventional positive position control to exploit linear dynamics of bistable …

Texture Analysis Using The Neutron Diffraction Method On The Non Standardized Austenitic Steel Process By Machining,Annealing, And Rolling, Tri Hardi Priyanto, Parikin Parikin, Meijuan Li

Makara Journal of Technology

Austenitic steel is one type of stainless steel which is widely used in the industry. Many studies on austenitic stainless steel have been performed to determine the physical properties using various types of equipment and methods. In this study, the neutron diffraction method is used to characterize the materials which have been made from minerals extracted from the mines in Indonesia. The materials consist of a granular ferro-scrap, nickel, ferro-chrome, ferro-manganese, and ferro-silicon added with a little titanium. Characterization of the materials was carried out in three processes, namely: machining, annealing, and rolling. Experimental results obtained from the machining process …

Ramifications Of Projectile Velocity On The Ballistic Dart Penetration Of Sand, Peter Anthony Sable

Master's Theses (2009 -)

With the advent of novel in-situ experimental measurement techniques, highly resolved quantitative observations of dynamic events within granular media can now be made. In particular, high speed imagery and digital analysis now allow for the ballistic behaviors of sand to be examined not only across a range of event velocities but across multiple length scales. In an attempt to further understand the dynamic behavior of granular media, these new experimental developments were implemented utilizing high speed photography coupled with piezo-electric stress gauges to observe visually accessible ballistic events of a dart penetrating Ottawa sand. Projectile velocities ranged from 100 to …

Maneuverability Of Ships With Small Draught In Steady Wind, Daeng Paroka, Andi Haris Muhammad, Syamsul Asri

Makara Journal of Technology

Wind force and moment may force a ship to drastically decrease its speed and use a large drift angle as well as a large rudder angle in order to maintain its course. Ships with a small draught might have more risk in maneuvering to its point of view compared with a ship with a larger draught. This paper discusses maneuverability of a ship with a small draught in steady wind. The effect of wind on ship speed, drift angle, and rudder angle are investigated in a steady state condition. Five different ratios of wind velocity to ship speed from 1.0 …

A Retrospective Study Of Amusement Ride Restraint And Containment Systems: Identifying Design Challenges For Statistically Rare Anthropometric Cases, Paula M. Stenzler

Engineering Management & Systems Engineering Theses & Dissertations

The intent of this project was to conduct a retrospective study of amusement ride restraint and containment systems’ failures to identify the challenges associated with existing design criteria to safely accommodate statistically rare groups that fall outside amusement industry standards. Innovations in ride technology provide an opportunity for injuries to occur if restraint and containment systems cannot properly accommodate unique patron anthropometry. It is paramount to understand how anthropometric features contribute to the patron’s ability to defeat ride restraint and containment systems. A systemic perspective was used based on industry accident data to frame the problem associated with restraint and …

The Decomposition Of Hydroxylammonium Nitrate Under Vacuum Conditions, Gregory A. Neff

Masters Theses

This research investigates the decomposition of the ionic liquid: hydroxylammonium nitrate (HAN), under vacuum conditions. All research was conducted at the Aerospace Laboratory for Plasma Experiments (ALPE) at Western Michigan University. Hydroxylammonium nitrate solution 24% wt. in H2O was used consistently throughout this research. A variety of temperatures and pressures ranging from 23°C to 645°C and 6E-3 Torr to 4 Torr, respectively, were used to decompose HAN. The primary gaseous species resulting from these decomposition conditions are N2O, NO, and trace amounts of NO2. The formation of H2O, and N2 is conditional on the experimental conditions, and the formation of …

Assessing User Expectations Of Undo In A Multi-User Cad Environment, Jeffrey Eric Nuss

Theses and Dissertations

Undo is a command that users rely on in most software applications. Its importance in multi-user CAD is no different. However, due to its unique nature, users may have different expectations regarding how undo should behave. This research seeks to better understand users' expectations regarding undo in multi-user CAD by having users participate in collaborative design exercises and then asking them how they would expect undo to behave. In addition, users participated in a survey in which they watched 8 videos showing users interacting within multi-user CAD and were then asked about how they would want undo to behave. Based …

Droplet Impingement On Superhydrophobic Surfaces, Cristian Esteban Clavijo Angeles

Theses and Dissertations

This dissertation explores the physics of droplet impingement on superhydrophobic surfaces. The research is divided in three categories. First, the effect of a slip boundary condition on droplet spreading/retracting is considered. A model is developed based on energy conservation to evaluate spreading rates on surfaces exhibiting isotropic and anisotropic slip. The results show that larger slip causes the droplet to spread out farther owing to reduced friction at the interface for both slip scenarios. Furthermore, effects of slip become magnified for large Weber numbers due to the larger solid-liquid contact area during the process. On surfaces with anisotropic slip, droplets …

Numerical Analysis For The Hemodynamics In Unruptured Cerebral Aneurysms, Hashem Mhd Hicham Alargha

Theses

A cerebral aneurysm is a vascular disorder characterized by abnormal focal dilation of a brain artery which is considered as a serious and potentially life-threatening condition. Cerebral aneurysms affect around 2%-5% of adults and they are fatal and can rupture with an overall mortality rate of more than 50%. Through computational fluid dynamics investigation, this study is offering a closer look into the initiation growth and rupture of cerebral aneurysms. Four focus points are studied in this thesis which are sensitivity analysis of blood viscosity in aneurysms, the effect of cerebral aneurysm size on wall stresses and strain, hazard effects …

Application Of A Multi-Zone Model For The Prediction Of Species Concentrations In Rapid Compression Machine Experiments, David Wilson

Master's Theses (2009 -)

Accurate chemical kinetic models, which predict species evolution and heat release rates in chemically reactive systems, are essential for further advancements in fuel and combustion technology. An experimental facility that is widely used for evaluating the accuracy of kinetic models is a rapid compression machine (RCM), which creates a well-defined reaction environment by compressing a reactive mixture inside a chamber. Generally, RCM experiments are conducted in order to obtain ignition delay data. However, chemical speciation data provides greater insight into reaction pathways, and is therefore a more rigorous benchmark for validating kinetic models. In order for a chemical kinetic model …

Modeling And Investigation Of Refrigeration System Performance With Two-Phase Fluid Injection In A Scroll Compressor, Rui Gu

Master's Theses (2009 -)

Vapor compression cycles are widely used in heating, refrigerating and air-conditioning. A slight performance improvement in the components of a vapor compression cycle, such as the compressor, can play a significant role in saving energy use. However, the complexity and cost of these improvements can block their application in the market. Modifying the conventional cycle configuration can offer a less complex and less costly alternative approach. Economizing is a common modification for improving the performance of the refrigeration cycle, resulting in decreasing the work required to compress the gas per unit mass. Traditionally, economizing requires multi-stage compressors, the cost of …

Thin Film Studies Toward Improving The Performance Of Accelerator Electron Sources, Md Abdullah Al Mamun

Mechanical & Aerospace Engineering Theses & Dissertations

Future electron accelerators require DC high voltage photoguns to operate beyond the present state of the art to conduct new experiments that require ultra-bright electron beams with high average current and higher bunch charge. To meet these demands, the accelerators must demonstrate improvements in a number of photogun areas including vacuum, field emission elimination in high voltage electrodes, and photocathodes. This dissertation illustrates how these improvements can be achieved by the application of suitable thin-films to the photogun structure for producing ultra-bright electron beams.

This work is composed of three complementary studies. First, the outgassing rates of three nominally identical …

Experimental Investigation Of Turbulent Structures And Non-Equilibrium Effects In Axial Wake Vortices Via Particle Image Velocimetry, Jeffry William Ely

Mechanical & Aerospace Engineering Theses & Dissertations

Vortices are a common phenomenon in fluid flows that arise as kinetic energy dissipates into heat via viscous interaction. They arise naturally at large scales in the form of dust devils, tornadoes, and as a counter-rotating vortex pair in the wake of aircraft. It is important to understand the conditions leading to their formation, their duration, and their dissipation in order to forecast or prevent undesirable effects. Among these deleterious effects is a decrease in safety of aircraft operations in the wake of other aircraft, an extremely common situation at airports around the world. A large number of mathematical models …