Mechanical Engineering Commons^™

Investigation The Effect Of Integrating Solar Desalination Systems With Firefighting Networks For Coastal Cities, Ramy Elramy, Mohamed Mahgoub, Mohamed Abdelgaied, Ayman Refat Abd Elbar

Journal of Engineering Research

This study investigates integrating solar desalination systems with seawater-based firefighting networks as a sustainable solution for coastal cities facing freshwater scarcity. This study evaluates technical feasibility, economic impact, and operational performance by comparing conventional seawater firefighting infrastructure with systems utilizing desalinated water produced via solar energy. The methodology includes a detailed component and cost analysis of both systems, supported by experimental pump performance tests using varying salt concentrations and seawater. Results indicate that desalinated water systems offer significant economic savings—approximately 48.82%—due to reduced corrosion, lower maintenance demands, and improved pump efficiency. Experimental findings also show that increased salinity accelerates cavitation …

Cyclic Combustion Pressure Dynamics Of A Diesel Engine Operating On Waste Frying Oil Biodiesel Blends Using Wavelets, Shady Elmozy, Ahmed Khaira Dr., Elshenawy Elshenawy Prof. Dr., Ali Mohamed Dr., Medhat Elkelawy Prof. Dr,

Journal of Engineering Research

This paper investigates the cyclic combustion pressure dynamics of a single-cylinder diesel engine burning waste frying oil biodiesel blends, employing statistical analysis and continuous wavelet transform (CWT) to evaluate combustion stability. Experiments were conducted at a constant engine load (90%) and speed (1500 rpm), with in-cylinder pressure data collected over 400 consecutive cycles for conventional diesel (RD) and biodiesel blends (UB10, UB30, UB50). Results demonstrate that biodiesel blends marginally reduce average peak cylinder pressure (PP) by 0.3–3.8% while lowering PP variability, evidenced by declining coefficients of variation (COV-PP: 1.27–1.48%), attributed to biodiesel’s elevated viscosity promoting consistent fuel-air mixing. Conversely, mean …

Combustion Characteristics And Cycle-To-Cycle Variations In A Diesel Generator Fueled With Used Frying Oil Biodiesel Blends, Shady Elmozy, Ahmad Khira Dr., E. A. El Shenawy Prof. Dr., Medhat Elkelawy Prof. Dr, Eng.

Journal of Engineering Research

This paper investigates the combustion characteristics and cycle-to-cycle variations in a stationary direct-injection diesel generator fueled with biodiesel derived from used frying oil (UFO) blended with conventional diesel. Used frying oil methyl ester (UFOME), referred to as UB100, was produced through a single-step alkali transesterification process and blended with diesel fuel in varying proportions (UB10, UB20, UB30, UB40, and UB50). Experiments were conducted on a single-cylinder, naturally aspirated diesel engine operating at a constant speed of 1500 rpm under five different load conditions: 0%, 25%, 50%, 75%, and 90%. In-cylinder pressure data from 400 consecutive cycles were analyzed to determine …

An Engineering Solution For Fan Aeroacoustics Measurements Correction In A Non-Anechoic Testing Environment, Saad-Eldin Taha, Mohamed Y.Zakaria, Mohamed Abdelgaied, M.M. Bassuoni Prof. Dr.

Journal of Engineering Research

Abstract- Nowadays, acoustic signatures of daily used applications are to be minimized. The study of noise generated through aerodynamic interaction with moving bodies has passed through different phases since the early 50s, and this leads to the evolvement of many analytical, empirical and computational techniques in order to be able to estimate the emitted noise. Concerning fan blades, until now the researches are still going for a reliable method for noise estimation during the early phases of design which help in the development of blades with a lower aeroacoustic signature, the Brooks, Pope and Marcolini (BPM) model was chosen to …

An Eulerian-Pfem Approach To Model Transient Capillary Forces On Moving Contact Lines Of Spreading Liquid Drops: Applications In Hydraulic And Fluid Dynamics, Elaf N. Mahrous, Syed Yousufuddin, Muhammad Saleem Professor, Mohammed N. Iqbal, Muhammad T. Bin-Saleem

Journal of Engineering Research

This study addresses the complexities of simulating multiphase flows, particularly the dynamics of droplet behaviour on solid substrates, which are influenced by intricate capillary interactions. Despite advancements in fixed-grid and moving-grid methodologies, there remains a critical gap in accurately modelling transient phenomena and dissipative forces at the solid-liquid interface. We introduce a novel Eulerian-particle finite element method (PFEM) framework that captures the transient capillary forces associated with the movement of contact lines in liquid droplet spreading scenarios. Through a numerical assessment of three established dissipative force models—Jiang’s, Bracke’s, and Seeberg’s we identify Jiang's model as the most effective and stable …

Anhydrous Ammonia As A Hydrogen Carrier Fuel For Solid Oxide Fuel Cells, Cole Anthony Wilhelm

Dissertations - ALL

In the years since humans realized that our actions could have profoundly harsh effects on the environment, we have been searching for ways to minimize our impacts, while also maintaining the same standard of living. One of the actions with such effects is power generation using fossil fuels, which has long been the largest source of energy. While efforts should be made to improve the efficiency of these power generation plants, we should also work to identify alternative opportunities for power generation without the use of fossil fuels. Some of these opportunities include hydroelectric, photovoltaic, wind, nuclear, and the combustion …

Corrosion Mitigation And Monitoring Of Bridge Tendons And Failure Forecasting Of Wastewater Force Mains, Stanley Chike Agbakansi

USF Tampa Graduate Theses and Dissertations

Corrosion remains a significant threat to civil infrastructure, resulting in costly repairsand potential structural failures. This dissertation addresses three critical aspects of corrosion: mitigation and monitoring of post-tensioned bridge tendons, and failure forecasting of wastewater force mains due to internal corrosion.

First, the research investigates the effectiveness of corrosion inhibitors (CIs) applied via pressure injection (impregnation) in post-tensioned tendons. The protective mechanisms and long-term performance of various inhibitors were evaluated to identify the most effective formulations. Among the tested inhibitors, MCI-2020 — a water-based, migratory, mixed-type corrosion inhibitor — demonstrated the most promising results, showing excellent corrosion protection while preserving …

Tailoring Gel Polymer Electrolytes For Advancing Quasi-Solid-State Batteries, Linrui Duan, Juchen Zhang, Mataz Alcoutlabi, Hongtao Sun

Mechanical Engineering Faculty Publications

Gel polymer electrolytes (GPEs) have attracted considerable attention due to their advantageous properties, such as uniform lithium deposition, stable solid electrolyte interphase (SEI) formation, nontoxicity, nonflammability, and leak-proof characteristics. In this study, a polyvinylidene fluoride hexafluoropropylene copolymer (PVDF-HFP)-based gel polymer electrolyte is synthesized via photo-polymerization, with a focus on examining the effects of curing time on electrolyte performance. The findings reveal that UV irradiation conditions significantly influence key material and electrochemical properties of the GPEs, including lithium-ion transference number, ionic conductivity, crystallinity, morphology, and liquid electrolyte uptake. Notably, the GPE cured for 120 s exhibited optimized performance, achieving an ionic …

Empowering Engineering Students To Become More Effective And Self-Regulated Learners Through Course-Integrated Learning Strategies Intervention: A Pilot Study In A Solid Mechanics Course, Huihui Qi, Richard Eugene Vallejo Jr., Changkai Chen, Minju Kim, Alex M. Phan, Marko Lubarda, Celeste Pilegard, Curt Schurgers

Psychology Faculty Articles and Research

Learning is a lifelong process exercised within and beyond the classroom and a vital skill in almost all technical professions. Engineers, in particular, are impacted by rapidly evolving technologies and practices that require continuous learning and adaptation long after their training and the initial transition into their professional careers. However, despite the critical role of learning in their academic success and profession, engineering students experience academically rigorous and challenging courses with very little emphasis or conscious focus on learning strategies that power effective learning. Often-used learning strategies such as rereading, highlighting, repetition, and memorization are intuitive for many students, yet …

Towards Sustainable Manufacturing: A Framework For Resource Conservation And Waste Mitigation, Mahmood Talal Sultan

Thesis/ Dissertation Defenses

The manufacturing industry drives economic expansion, but it also contributes significantly to environmental change and shortages of resources. Therefore, the transformation to sustainable manufacturing has become an urgent need, driven by worldwide efforts to address climate change, minimize waste, and protect valuable assets. This thesis develops a robust framework tailored to the manufacturing sector, focusing on resource conservation and waste reduction. The framework is built on the identification and categorization of Key Performance Indicators (KPIs) and assessment tools, which address five major implementation challenges: complex supply chains, regulatory barriers, economic challenges, technological limitations, and social and cultural challenges.

To build …

Knee-Thigh-Hip Impact In Children: Effects Of Age And Impact Velocity, Mohammad Ziad Turki

Thesis/ Dissertation Defenses

Brief introduction: This thesis examined the crash impact injury outcomes of the knee-thigh-hip complex (KTH) in children based on age and impact velocity using computational modelling. Child occupant (3YO, 6YO, 10YO) Total Human Body Model for Safety (THUMS) models developed by Toyota were used to evaluate the effects of age and impact velocity on pediatric KTH crash impact response. Aims: The main objectives of this thesis are to analyze the effect of child age and impact velocity on KTH crash impact response. Methods: The knee impact simulations were performed based on different impact velocities (1.2, 3.5, 7.2, …

Nanoscale Structure-Property Relationships Of Cyanate Ester As A Function Of Extent Of Cure, Khatereh Kashmari, Josh Kemppainen, Sagar U. Patil, Julieta Barroeta Robles, Pascal Hubert, Gregory Odegard

Michigan Tech Publications

Cyanate esters are key thermosetting resins for composite materials that require structural integrity and resistance to elevated temperatures. Because cyanate ester composites require relatively high processing temperatures, they are susceptible to the formation of process-induced residual stresses, which compromise their overall strength and durability. Process modeling is a key strategy for optimizing processing parameters to minimize such residual stresses. A necessary component of effective and efficient process modeling of composites is computationally established resin property evolution relationships for a range of processing parameters. In this study, the physical, mechanical, and thermal properties of a cyanate ester resin are established as …

How’S It Growing? Tools For Observing Snow And Sea Ice In A Changing Arctic Ocean, Ian Alexander Raphael

Dartmouth College Ph.D Dissertations

September Arctic sea ice extent has diminished by roughly 50% in the 45 years since satellite observations began. The Arctic Ocean may experience ice-free summers within the next decade, with implications for habitat, resource extraction, geopolitics, and local and global climate change. To predict how Arctic sea ice will change in the future, we need to understand its behavior in the present. In situ sea ice mass balance measurements (snow accumulation, ice growth, snow and ice surface melt, and bottom melt) are essential for studying the processes driving rapid changes in the ice pack, and for validating remote sensing measurements …

The Aerodynamics Of Swept, Canted, And Slotted Winglets, Andrew K. Mahler

Mechanical Engineering Master's Theses

Winglets have been used to improve the aerodynamic performance of wings. They do this by decreasing the lift induced drag that is experienced by the wing. The winglet modifies the wingtip vortex generated by adjusting both its size, location and strength. Motivated by previous research on the manipulation of wake vorticity through the use of a forward or backward sweep discovered originally when investigating crescent wings, the presented work investigates the role of sweep, cant and slots on winglets. Sweep was first applied to positive and negative canted wings with a symmetric airfoil, the ONERA M6. The wing flows were …

Thermal Rheological Properties Of Heat-Moisture Modified And Its Application In Multigrain Cookies, Thi Huyen Trang, Li Xianghong, Miao Jinxu, Wang Faxiang, Liu Yongle, Li Shuang

Food and Machinery

［Objective］ To develop low -burden,high -nutrient functional baked foods.［Methods］ A single -factor experimental design is employed,with rapid visco analyzer,rheometer,and differential scanning calorimeter to analyze the physicochemical properties of heat -moisture modified wheat flour.The cookie formula is optimized based on sensory evaluation.［Results］ Heat -moisture treatment significantly enhances the pasting stability and resistant starch content of wheat flour.The optimal auxiliary ingredient formula is 50 g of heat-moisture modified wheat flour,20 g of oat flour,10 g of mung bean flour,and 6 g of resistant dextrin powder.Compared with the control group,the cookies made from the experimental formula show a significantly lower digestibility,with a glycemic …

Development Of An Embedded Iot Board For Real-Time Floor Estimation Of Autonomous Robots, Carter J. Sorensen

Electronic Theses and Dissertations

As service robots become more prevalent in multi-story environments such as hospitals, hotels, and laboratories, accurate floor-level detection is critical to ensuring operational reliability. Consider a robot tasked with delivering medical samples in a multi-story laboratory. Without accurate feedback, a robot exiting on the wrong floor could introduce delays, disrupt workflows, or compromise sample integrity. Internet of Things (IoT) technologies offer a way to address these risks by providing real-time error detection and corrective capability. However, current IoT-based floor estimation systems often require invasive modifications to building infrastructure—particularly elevator control panels. These approaches introduce challenges related to cost, liability, backward …

Sae Baja Drivetrain Capstone 2024-2025, Leslie Alvarez Cisneros

University Honors Theses

This thesis reviews the 2024-2025 Baja SAE Drivetrain capstone project. The Baja SAE competition mimics real world engineering problems where teams of students design and build off-road vehicles that can handle tough, rough terrain. The objective of this capstone was to design a functional and reliable drivetrain system for the vehicle, within the constraints of a limited budget and the SAE competition guidelines. As part of a 12-member capstone team divided into three subgroups: frame, suspension, and drivetrain. As part of a four person drivetrain team, we picked up where the 2023-2024 team left off by relying on their past …

Human Gut Commensal Alistipes Timonensis Modulates The Host Lipidome And Delivers Anti-Inflammatory Outer Membrane Vesicles To Suppress Colitis In An Il10-Deficient Mouse Model, Ethan Older, Mary K. Mitchell, Andrew Campbell, Xiaoying Lian, Michael Madden, Yuzhen Wang, Lauren E. Van De Wal, Thelma Zaw, Brandon N. Vanderveen, Rodney Tatum, E. Angela Murphy, Yan-Hua Chen, Daping Fang, Melissa Ellermann, Jie Li

Faculty Publications

Correlative studies have linked human gut microbes to specific health conditions. Alistipes is one such microbial genus negatively linked to inflammatory bowel disease (IBD). However, the protective role of Alistipes in IBD is understudied, and the underlying molecular mechanisms remain unknown. In this study, colonization of Il10-deficient mice with Alistipes timonensis DSM 27924 delays colitis development. Colonization does not significantly alter the gut microbiome composition, but instead shifts the host plasma lipidome, increasing phosphatidic acids while decreasing triglycerides. Outer membrane vesicles (OMVs) derived from Alistipes are detected in the plasma of colonized mice, carrying potentially immunomodulatory metabolites into the …

Design And Development Of Hip Implants For Longevity Through Integrating Advanced Groove Structures And Additive Manufacturing, Asarudheen Abdudeen

Thesis/ Dissertation Defenses

This doctoral research concerns the design and optimization of hip implants (HIs) to enhance performance, durability, and improve patient outcomes by addressing the key issues of wear, deformation, and stress distribution. Innovative surface groove designs have been introduced to both a solid and a hollow femoral head with the aim of reducing friction and wear. The addition of grooves, with both a hemispherical and rectangular cross-section, onto the femoral head reduced friction, as debris produced by the inner liner was trapped within the grooves, significantly reducing adhesive wear. A numerical simulation study compared the effects of surface modifications — both …

A Versatile Platform For Designing And Fabricating Multi-Material Perfusable 3d Microvasculatures, Nathaniel Harris, Charles Miller, Min Zou

Mechanical Engineering Faculty Publications and Presentations

Perfusable microvasculature is critical for advancing in vitro tissue models, particularly for neural applications where limited diffusion impairs organoid growth and fails to replicate neurovascular function. This study presents a versatile fabrication platform that integrates mesh-driven design, two-photon lithography (TPL), and modular interfacing to create multi-material, perfusable 3D microvasculatures. Various 2D and 3D capillary paths were test-printed using both polygonal and lattice support strategies. A double-layered capillary scaffold based on the Hilbert curve was used for comparative materials testing. Methods for printing rigid (OrmoComp), moderately stiff hydrogel (polyethylene glycol diacrylate, PEGDA 700), and soft elastomeric (photocurable polydimethylsiloxane, PDMS) materials were …

Bloom Pattern Data, Zhongyuan Wang, Robert J. Lang, Larry L. Howell

ScholarsArchive Data

This data is the supplementary material of the paper "Bloom Patterns: Radially Expansive, Developable, and Flat-Foldable Origami" by Zhongyuan (Kelvin) Wang , Robert J. Lang, and Larry L. Howell.

We present bloom patterns as a family of radially expansive, flat-foldable, and developable origami patterns, many of which are rotationally symmetric. Bloom patterns are defined with a generalized definition and a standardized definition. A classification scheme for bloom patterns is identified, and several types of bloom patterns are analysed. The distinct helical nature that characterizes bloom patterns is described, and a set of compatibility conditions is derived to help determine if …

Effect Of Fibonacci-Inspired Multi-Layer Aluminum Sheets Under Double-Nose Projectile Impact, Shaima Ali Alhosani

Thesis/ Dissertation Defenses

This research examines the ballistic performance of multi-layered Aluminum 2024 sheets designed with Fibonacci-inspired spacing patterns when subjected to double-nose projectile impacts. Through a numerical simulation, five configurations were studied: a monolithic reference plate (L0) with 0.82 mm thickness, and four multi-layer configurations (L1 to L4), all maintaining a constant total thickness of 1.74 mm. Three projectile types were considered Blunt-Conical (BC), Conical-Blunt (CB), and Blunt-Blunt (BB). Among these, the L1 configuration (two layers separated by a 0.1 mm gap) consistently offered the best ballistic resistance, outperforming more complex arrangements. As layer complexity increased from L1 to L4, overall performance …

Derivation And Experimental Validation Of A Parameterized Nonlinear Froude–Krylov Force Model For Heaving-Point-Absorber Wave Energy Converters, Houssein Yassin, Tania Demonte Gonzalez, Gordon Parker, Giorgio Bacelli, Carlos Michelen

Michigan Tech Publications

Wave energy converters (WECs) have gained significant attention as a promising renewable energy source. Optimal control strategies, crucial for maximizing energy extraction, have traditionally relied on linear models based on small motion assumptions. However, recent studies indicate that these models do not adequately capture the complex dynamics of WECs, especially when large motions are introduced to enhance power absorption. The nonlinear Froude–Krylov (FK) forces, particularly in heaving-point-absorbers with varying cross-sectional areas, are acknowledged as key contributors to this discrepancy. While high-fidelity computational models are accurate, they are impractical for real-time control applications due to their complexity. This paper presents a …

Computational And Experimental Study Of Slow Crack Growth In High Density Polyethylene, Abdulla Almomani

Thesis/ Dissertation Defenses

This dissertation investigates the slow crack growth (SCG) behavior of High-Density Polyethylene (HDPE) under various mechanical and environmental conditions. The study combines experimental analysis and computational modeling to enhance the understanding of SCG mechanisms in HDPE, particularly in pressurized pipes and under the exposure to hydrocarbons. A novel Crack Layer (CL) theory-based SCG model is developed and validated through experimental data, offering a predictive framework for HDPE failure assessment. The main objective of this dissertation is to quantify and model the viscoelastic-viscoplastic behavior of HDPE under monotonic and cyclic loading conditions while addressing SCG kinetics in structural applications. The study …

Minimum Ghg Emissions And Energy Consumption Of U.S. Pet And Polyolefin Packaging Supply Chains In A Circular Economy, Utkarsh S. Chaudhari, Abhishek Patil, Tasmin Hossain, David Watkins, Damon S. Hartley, Barbara K. Reck, Robert Handler, Anne T. Johnson, Vicki S. Thompson, David Shonnard

Michigan Tech Publications

There is a wide agreement on the urgency of transforming linear management of plastics towards a circular economy model. However, no clear pathways exist as to required recycling technologies involved and system-wide environmental impacts. This study explores such pathways in the U.S. for the most commonly used packaging plastics through a combination of mechanical and emerging advanced recycling technologies. A system optimization model aimed at minimizing environmental impacts was developed to determine optimal end-of-life (EOL) management and locations of existing and emerging U.S. recycling infrastructures. Our study includes material flows from virgin resin production through semi-manufacturing processes to existing EOL …

Efficient Thermal Design Of Data Centers, Keats M. Baggett, Andrew Ergood, Colin Brace, Jack Zilligen

Mechanical Engineering

Our sponsor needs a way to categorize and quantify the top 3 colocation center sites based on a series of criteria for given power specs. The sponsor also needs a single innovative cooling method to meet thermal and power requirements while also being manufacturable at scale. This device must also be able to interact with the given Colocation Heating Ventilation and Air Conditioning (HVAC) system. This design will be tested to provide insight and data that will be applicable to further the development of colocation center cooling. This project will be executed by the Cal Poly senior project team and …

Aerospace Fastener Installation Tool, Anthony I. Berghout, Matthew K. Eggers, Liam Dunsmore, Jose Pardo

Mechanical Engineering

Contamination, particularly in aerospace manufacturing environments, is a significant concern, especially with fastener designs that incorporate torque-rated breakaway pieces for easier installation. These breakaway pieces are also known as pintails. Howmet has tooling that can collect loose pintails during installation, but they have small capacities and are not ergonomic for aerospace technicians. Their current need is for a light and ergonomic tool capable of installing a wide variety of Ergo-Tech® fasteners while having a large capacity to collect pintails and improve aerospace manufacturing methods. For this Critical Design Stage, we have finalized a design that allows Pintails to pass through …

2-Axis Solar Panel Tracker, Danica Wong, Oliver Barnaal, Anton Orme

Mechanical Engineering

Solar panels generate energy from sunlight. To do this it’s important that they remain pointed at the sun throughout the day. The Cal Poly Micro Grid Lab runs a class that uses a student made solar panel and tracking mount as an instructional tool. This project is beginning to show signs of wear from outdoor use and is unable to run without constant input due to some significant design flaws. The lab needs a new version of the mount to be made that is significantly more reliable and easier to use.

Edwards Lifesciences: Esheath+ Scoring Automation, Tony Lee Avina, Kirth Hirth, Charith Sunku, Humberto Salazar-Banuelos

Mechanical Engineering

Due to a non-disclosure agreement with our sponsor, Edwards Lifesciences, the contents of the report have been omitted.

Kinetic, Wind-Driven Metal Sculpture, Irene Songhee Han, Aiden Brown Largay, Madeline Vang Xiong

Mechanical Engineering

The Interdisciplinary Senior Design Team “Flying Flora” from Cal Poly’s College of Engineering has been tasked with designing and building a wind-driven dynamic metal sculpture for the San Luis Obispo Botanical Garden. The botanical garden wants to fill a large, centrally located vacant space with a kinetic sculpture to attract and welcome visitors. The final design, as approved by the garden’s directors, features a large metal California poppy below a stained-glass and metal butterfly. The flower rotates smoothly in typical wind conditions, drawing the attention of visitors to the sculpture. The butterfly is stationary, positioned at an angle from the …