Mechanical Engineering Commons^™

Utilization Of Empirical Models To Determine The Bulk Properties Of Compressed Sound Absorptive Materials, Ruimeng Wu

Theses and Dissertations--Mechanical and Aerospace Engineering

Empirical models based on flow resistivity are commonly used to determine the bulk properties of porous sound absorbing materials. The bulk properties include the complex wavenumber and complex characteristic impedance which can be used directly in simulation models. Moreover, the bulk properties can also be utilized to determine the normal incidence sound absorption and specific acoustic impedance for sound absorbing materials of any thickness and for design of layered materials. The sound absorption coefficient of sound absorbing materials is measured in an impedance tube using wave decomposition and the measured data is used to determine the flow resistivity of the …

Investigation Of Polishing Methods And Surface Analysis After Machining Aisi 4140 Alloy Steel, Qiang Qi

Theses and Dissertations--Mechanical and Aerospace Engineering

AISI 4140 alloy steel has been a very common material to be investigated in automotive and aerospace industries for several decades. AISI 4140 alloy steel is chromium, molybdenum, and manganese containing low alloy steel. It has high fatigue strength, abrasion and impact resistance, toughness, and torsional strength. The functional performance is largely determined by the surface states after machining.

The aim of the present study is to explore the polishing methods and surface analysis after machining AISI 4140 alloy steel in different cutting speeds and cooling conditions. The surface analysis includes surface roughness, hardness and residual stresses. Compared to traditional …

Autonomous Quadrotor Collision Avoidance And Destination Seeking In A Gps-Denied Environment, Thomas C. Kirven

Theses and Dissertations--Mechanical and Aerospace Engineering

This thesis presents a real-time autonomous guidance and control method for a quadrotor in a GPS-denied environment. The quadrotor autonomously seeks a destination while it avoids obstacles whose shape and position are initially unknown. We implement the obstacle avoidance and destination seeking methods using off-the-shelf sensors, including a vision-sensing camera. The vision-sensing camera detects the positions of points on the surface of obstacles. We use this obstacle position data and a potential-field method to generate velocity commands. We present a backstepping controller that uses the velocity commands to generate the quadrotor's control inputs. In indoor experiments, we demonstrate that the …

Product Disassemblability And Remanufacturability Assessment: A Quantitative Approach, Ammar Ali

Theses and Dissertations--Mechanical and Aerospace Engineering

Majority of the products get discarded at end-of-life (EoL), causing environmental pollution, and resulting in a complete loss of all materials and embodied energy. Adopting a closed-loop material flow approach can aid preventing such losses and enable EoL value recovery from these products. Design and engineering decisions made and how products are used impact the capability to implement EOL strategies such as disassembly and remanufacturing. Some underlying factors affecting the capability to implement these EOL strategies have been discussed in previous studies. However, relevant metrics and attributes are not well defined and comprehensive methods to quantitatively evaluate them are lacking. …

Application Of Multiaxial Cyclic Loading For Constitutive Model And Parameter Determination Of Steels, Bassem Felemban

Electronic Theses and Dissertations

For many candidate materials, constitutive models and their parameters are identified using uniaxial test data. Real components, however, generally operate in a multi-axial loading environments. Consequently, constitutive models deployed by uniaxial conditions may carry over to service conditions with inherit limitations. Research is proposed to determine the constitutive model constants for the creep and plasticity responses of a material via multi-axial fatigue testing which may contain ratcheting. It is conjectured that directly regressing data under conditions that favor those of actual service use will lead to more accurate modeling under these conditions, as well as a reduced consumption of model …

Heat Transfer, Friction, And Turbulent Analysis On Single Ribbed-Wall Square Channel, Christopher Vergos

Electronic Theses and Dissertations

An experimental investigation of heat transfer and friction behavior for a fully developed flow in a non-rotating square channel was conducted under a wide range of Reynolds numbers from 6,000 to 180,000. The rig used in this study was a single ribbed wall variant of Ahmed et al.'s [ 1 ] rig from which results of this rig were compared. Ahmed et al.'s rig was a replica of Han et al.'s square channel [ 2 ] used to validate their work, and expand the Reynolds number range for both heat transfer and friction data. The test section was 22 hydraulic …

Investigation Of Heat Transfer Enhancement Within A Concentric Annulus, Alexander Hanhold

Electronic Theses and Dissertations

Effective heat exchange is key for many energy applications including heat exchangers, heat extraction from heat source, and heat rejection to ambient thermal sink. This study focuses on the investigation for a specific heat exchange configuration, namely heat removal within a concentric annular passage using helical turbulators and jet impingement. Numerical testing was used to see how the different geometric parameters affect the heat transfer and pressure drop within the annulus by using helicoil turbulators. A vast range of designs were studied by changing the turbulator shape, pitch, and blockage ratio while maintaining a constant Reynolds number of 25,000. CFD …

Academic Blade Geometries For Baseline Comparisons Of Forced Vibration Response Predictions, James Little

Electronic Theses and Dissertations

Predicting the damping associated with underplatform dampers remains a challenge in turbomachinery blade and friction damper design. Turbomachinery blade forced response analysis methods usually rely on nonlinear codes and reduced order models to predict vibration characteristics of blades. Two academic blade geometries coupled with underplatform dampers are presented here for comparison of these model reduction and forced response simulation techniques. The two blades are representative of free-standing turbine blades and exhibit qualitatively similar behavior as highly-complex industrial blades. This thesis fully describes the proposed academic blade geometries and models; it further analyzes and predicts the blades forced response characteristics using …

A Study On The Plasticity And Fracture Behaviors Of Inconel 718 Under Multiaxial Stress And Extremely Low Cycle Fatigue Loadings, Mohammed Algarni

Electronic Theses and Dissertations

Engineering materials and structures are usually subjected to multiaxial stress states loading due to geometrical effects, residual stresses, or multi-directional loading. Ductile fracture and Extremely Low Cycle Fatigue (ELCF), less than 100 cycles to fail, are two common and co-exist failure modes in many engineering structures. However, the linkage between these two failure modes under multi-axial loading conditions has never been systematically studied. This research summarizes an extensive work of experimental and numerical studies of ductile fracture and ELCF under different stress states for nickel-base superalloy material "IN718" under room temperature. Specially designed specimens and tests were used to achieve …

Continuous Oscillation: Vibrational Effects And Acceptable Frequency Ranges Of Small Bore Piping In Field Applications, Marie Kasprzyk

Electronic Theses and Dissertations

In turbomachinery, a common failure mode is cracking of welds at the equipment and piping connection point. Each incidence of these cracks causes a forced shutdown to perform repairs that cost millions of dollars. This type of failure is predominately seen in small bore piping, which has a nominal diameter of 2 inches and smaller. This thesis addresses the failure prediction analysis of small bore piping, specifically in turbomachinery applications. Performing failure analysis to predict the potential cracking of welds will allow for replacement of the piping during a planned shutdown which in the long term saves money due to …

Statistical Analysis Of Multi-Row Film Cooling Flowfields, Craig Fernandes

Electronic Theses and Dissertations

A huge part of modern day power generation research and development strives to achieve higher thermal efficiencies and specific work outputs for both gas turbine Brayton and combined cycles. Advances in cooling technologies, both internal to turbine blades and external, provide the easiest way to accomplish this by raising the turbine inlet temperature far beyond the super-alloy's allowable temperature. Discrete film cooling injection, an external cooling technique, ensures a cool blanket of compressed air protects the blade surface from the harsh mainstream gas. To optimize the coverage and effectiveness of the film, a thorough understanding of the behavior and flow …

Tensile-Compressive Asymmetry And Anisotropy Of Fused Deposition Modeling Pla Under Monotonic Conditions, Casey Perkowski

Electronic Theses and Dissertations

Additive Manufacturing (AM) continues to gain popularity for its ability to produce complexly-shaped final use components that are impractical to manufacture by traditional methods; however, additive manufactured parts contain complex mesostructures that result in directionally-dependent mechanical properties that have yet to be fully characterized. This effort demonstrates a framework of experimental and analytical methods needed to characterize the uniaxial monotonic behavior of fused deposition modeling PLA using tensile and compressive experiments on specimens printed at various orientations. Based on experimental results, the asymmetry and anisotropy of the tensile and compressive response was analyzed for a candidate material. Specimens from different …

Multi-Axial Thermomechanical Characterization Of Shape Memory Alloys For Improved Stability, Douglas Nicholson

Electronic Theses and Dissertations

Shape recovery in shape memory alloys (SMAs) occurs against external stress by means of a reversible thermoelastic solid state phase transformation typically between so-called austenite, martensite and R-phases. The ability to do work enables their use as high-force actuators in automotive and aerospace applications while superelastic NiTi is of interest in biomedical devices such as stents. Both R-phase and martensite can detwin, reorient and undergo a thermal or stress induced transformation. For these reasons, it is difficult from ordinary macroscopic measurements to decouple elastic and inelastic contributions (from their respective phases) from the overall deformation. In situ neutron diffraction is …

First Level Design And System Design Of Janus Liquid Oxygen-Liquid Methane Lander, Jahir Fernandez

Open Access Theses & Dissertations

Taking humans to space has always been a fantastic feat, but taking humans to another planet in our solar system is the new goal. Technology has come a long way and with that, so has our knowledge of space and what can be done with current technology to accomplish our goal. These technologies allow for a more efficient space system to transport future astronauts using liquid oxygen and liquid methane (LO2-LCH4) as propellants. This combination of propellants, LO2-LCH4, brings a variety of benefits. One of the main advantages is that they can be recovered or created from local resources, using …

The Design, Construction And Operation Of System To Analyze The Decomposition Gases Of Af-M315e, Jonathan Alejandro Valenzuela Brok

Open Access Theses & Dissertations

With the current trend of aerospace organizations towards developing green monopropellant, the key priority is to eliminate the use of highly dangerous monopropellants, such as hydrazine. In that vein, one of the best candidates to replace hydrazine is a monopropellant known as AF-M315E. AF-M315E was developed by the Air Force and is currently being advanced by NASA and private corporations for use on various satellite platforms, with NASA looking to launch a test satellites part of their Green Propellant Infusion Mission (GPIM), Raytheon providing support on the Missile Defense Agency's Network Centric Airborne Defense Element (NCADE) program and Department of …

Co-Gasification Of Coal And Biomass Wastes In An Entrained Flow Gasifier: Modelling, Simulation And Integration Opportunities, Dalia A. Ali Eng, Mamdouh A. Gadalla Prof., Omar Y. Abdelaziz, Christian P. Hulteberg, Fatma H. Ashour Prof.

Chemical Engineering

Gasification processes convert carbon-containing material into syngas through chemical reactions in the presence of gasifying agents such as air, oxygen, and steam. Syngas mixtures produced from such processes consist mainly of carbon monoxide (CO), hydrogen (H2), carbon dioxide (CO2), and methane (CH4); this gas can be directly utilised as a fuel to produce electricity or steam. Besides, it is regarded as a basic feedstock within the petrochemical and conventional refining industries, producing various useful products like methanol, hydrogen, ammonia, and acetic acid. In this work, a rigorous process model is developed to simulate the co-gasification of coal-biomass blends through an …

Method For Carbon Dioxide Splitting, James E. Miller, Richard B. Diver, Nathan P. Siegel

Other Faculty Research and Publications

A method for splitting carbon dioxide via a two-step metal oxide thermochemical cycle by heating a metal oxide compound selected from an iron oxide material of the general formula A_xFe_3-xO₄, where 0≦x≦1 and A is a metal selected from Mg, Cu, Zn, Ni, Co, and Mn, or a ceria oxide compound of the general formula M_aCe_bO_c, where 0

Human Centered Design Of An Open-Drum, Treadle Thresher For Quinoa Farmers In The Andes Of Northern Peru, Robert A. Hayes

Dissertations, Master's Theses and Master's Reports

Growing international demand for quinoa in recent years has led to increased production throughout its South American range, including the Peruvian Andes. Small-scale farmers, who are among the poorest Peruvians, are increasingly growing quinoa for both food security and economic benefit; however, manual harvesting activities, such as threshing, are labor-intensive and time-consuming. This report documents the design, construction and operation of prototype quinoa thresher in a rural village in Northern Peru. In addition, an overview of the history and evolutionary approach to design for the developing world is presented. From this overview, a series of criteria is considered for the …

Using Lower Extremity Muscle Activations To Estimate Human Ankle Impedance In The External-Internal Direction, Lauren N. Knop

Dissertations, Master's Theses and Master's Reports

For millions of people, mobility has been afflicted by lower limb amputation. Lower extremity prostheses have been used to improve the mobility of an amputee; however, they often require additional compensation from other joints and do not allow for natural maneuverability. To improve upon the functionality of ankle-foot prostheses, it is necessary to understand the role of different muscle activations in the modulation of mechanical impedance of a healthy human ankle. This report presents the results of using artificial neural networks (ANN) to determine the functional relationship between lower extremity electromyography (EMG) signals and ankle impedance in the transverse plane. …

The Role Of Active Flow-Control Devices In The Dynamic Aeroelastic Response Of Wind Turbine Rotors, Muraleekrishnan Menon Menon Muraleedharan Nair

Dissertations, Master's Theses and Master's Reports

The significance of wind as a renewable source of power is growing with the increasing capacity of individual utility-scale wind turbines. Contemporary wind turbines are capable of producing up to 8 MW and consequently, their rotor sizes are rapidly growing in size. This has led to an increased emphasis on studies related to improvements and innovations in load-control methodologies. Most often than not, controlling the loads on an operational turbine is a precarious scenario, especially under high wind loading. The up-scaling of turbine rotors would thus benefit from a rationale change in load control through methodologies such as variable-speed stall, …

Multi-Modal And Short-Range Transmission Loss In Ice-Covered, Near-Shore Arctic Waters, Miles B. Penhale

Dissertations, Master's Theses and Master's Reports

In the past century, extensive research has been done regarding the sound propagation in arctic ice sheets. The majority of this research has focused on low frequency propagation over long distances. One of the most commonly used excitation methods for air-ice-water layers has been explosives. However, environmental regulation has become more stringent, disallowing the use of almost all explosive excitation types. Due to changing climate conditions in these environments, new experimentation is warranted to determine sound propagation characteristics in, through, and under thin ice sheets, in shallow water, over short distances. In April, 2016 several experiments were conducted approximately 2 …

The Emission And Particulate Matter Oxidation Performance Of A Scr Catalyst On A Diesel Particulate Filter With A Downstream Scr, Sagar Sharma

Dissertations, Master's Theses and Master's Reports

Selective catalytic reduction (SCR) systems along with a NH₃ slip control catalyst (ASC) offers NOₓ conversion efficiency >90 % with NH₃ slip < 20 ppm. However, future heavy duty diesel (HDD) engines are designed for higher engine-out NOₓ to improve fuel consumption. Consequently, there is a strong desire to further improve the NOₓ reduction performance of SCR systems, to meet the 2015 California Optional Low NOₓ Standard. SCR catalysts on a diesel particulate filter provide an effective solution to reduce NOₓ and PM using a single aftertreatment device. It also provides an opportunity to increase the SCR volume to achieve NOₓ conversion efficiency >95 %. A downstream SCR catalyst substrate can be used to get additional NO_x conversion by using the SCRF^® outlet NH₃ to increase the cumulative NOₓ conversion of the system.

In this study, NOₓ reduction, NH₃ slip and PM oxidation performance of a Cu-zeolite SCRF^® with a downstream Cu-zeolite SCR were investigated based on engine experimental data at steady state conditions. The experimental data were collected at varying SCRF^® inlet temperatures, space velocities, inlet …

Impact Of Natural Gas Direct Injection On Thermal Efficinecy In A Spark Ignition Engine, James Sevik

Dissertations, Master's Theses and Master's Reports

Interest in natural gas as an internal combustion engine fuel has been renewed due to its increasing domestic availability and stable price relative to other petroleum fuel sources. Natural gas, comprised mainly of methane, allows for up to a 25% reduction in engine out CO2 emissions due to a more favorable hydrogen-to-carbon ratio, relative to traditional petroleum sources. Traditional methods of injecting natural gas can lead to poor part-load performance, as well as a power density loss at full load due to air displacement in the intake manifold. Natural gas direct injection, which allows the fuel to be injected directly …

Experimental Investigations Of Temperature Controlled Innovative Annular Flow-Boiling Of Fc-72 In Millimeter Scale Ducts – Steady And Enhanced Pulsatile Realizations, Patcharapol Gorgitrattanagul

Dissertations, Master's Theses and Master's Reports

Steady and steady-in-the-mean shear driven annular flow-boiling is experimentally investigated in this thesis. By annular flow-regime one means separated liquid and vapor flows with the flowing liquid film staying on the boiling-surface.

The goals for the steady annular flow-boiling operations are to better understand relative importance of heat-transfer mechanisms (nucleation versus convective phase-change, with convective meaning absence of nucleation) and to develop better quantitative characterizations/correlations for heat-transfer rates. The goals for the steady-in-the-mean annular investigations was to explore improved means of significantly increasing heat transfer rates - while retaining the flow-regime's annularity.

The experimental investigations (with FC-72 as a working …

Effect Of Spark Advance And Fuel On Knocking Tendency Of Spark Ignited Engine, Abhay S. Joshi

Dissertations, Master's Theses and Master's Reports

Knock, in spark ignition engine is the combustion caused by the autoignition of the fuel-air mixture. It is the phenomenon that limits engine performance and thermal efficiency. Knock also has an adverse effect on emissions and fuel economy. Engine designers target engines with maximum power and torque output without compromising on fuel economy. Engine downsizing is the method generally adopted. The main goal of engine downsizing is to achieve better fuel economy while increasing the power and torque output of the engine. Better fuel economy is achieved by reducing the displaced volume which in turn means a much higher brake …

Simulation Of Diesel Particulate Filter Regeneration Using Lattice Boltzmann Method, Kshitiz Kumar Jain

Dissertations, Master's Theses and Master's Reports

Lattice Boltzmann Method is a novel approach, which has shown promise in solving a wide variety of fluid flow problems including single and multi-phase flows in complex geometries. Volume elements of the fluid domain are considered to be composed of particles and these particles fall under a velocity distribution function at each grid point. Particles collide with each other under the influence of external forces and the rules of collision are defined so as to be compatible with the Navier-Stokes Equation. In the current work, LBM has been applied to Diesel Particulate filters which is a device used for reducing …

Turbulent Transition Simulation And Particulate Capture Modeling With An Incompressible Lattice Boltzmann Method, John R. Murdock

Dissertations, Master's Theses and Master's Reports

Derivation of an unambiguous incompressible form of the lattice Boltzmann equation is pursued in this dissertation. Further, parallelized implementation in developing application areas is researched. In order to achieve a unique incompressible form which clarifies the algorithm implementation, appropriate ansatzes are utilized. Through the Chapman-Enskog expansion, the exact incompressible Navier-Stokes equations are recovered. In initial studies, fundamental 2D and 3D canonical simulations are used to evaluate the validity and application, and test the required boundary condition modifications. Several unique advantages over the standard equation and alternative forms found in literature are found, including faster convergence, greater stability, and higher fidelity …

Electromagnetic Signal Feedback Control For Proximity Detection Systems, Adam K. Smith

Dissertations, Master's Theses and Master's Reports

Coal is the most abundant fossil fuel in the United States and remains an essential source of energy. While more than half of coal production comes from surface mining, nearly twice as many workers are employed by underground operations.

One of the key pieces of equipment used in underground coal mining is the continuous mining machine. These large and powerful machines are operated in confined spaces by remote control. Since 1984, 40 mine workers in the U. S. have been killed when struck or pinned by a continuous mining machine. It is estimated that a majority of these accidents could …

A 3 D- Fem Study On The Stress Distributions In Pediatric Skull Due To Impact From Free Fall, Suryanshu Walvekar

Dissertations, Master's Theses and Master's Reports

Abstract

Brain is vulnerable to injuries even from low heights of fall. There are many infant casualties who get severe brain injury each year. This research is a simulated study of the stress patterns and values when human infant skull is subjected to free fall. The input velocity was calculated using simple free fall velocity formulas and was fed into the simulation. Model was meshed and refined using Hypermesh software. RADIOSS solver of the Hyperworks package was used to analyze and draw results for the simulation process. Various types of stresses and strains were extracted and plotted against respective drop …

A 3d Fem Comparative Study On The Impact Response Between Human Head And Nocsae Head Due To Free Fall, Amey S. Badhe

Dissertations, Master's Theses and Master's Reports

We all enjoy sports be it watching or playing. Concussion is well known topic when it comes sports related injuries. However, concussion and brain injury is not exclusive to sports and outdoor activities. Sometimes, even the impact due to slip and fall at small heights can cause serious damage to the head and brain. This report studies the response generated in the human head model and the commercially use dummy NOCSAE headform due to drop from height of 2, 3, 4 and 5 feet. Earlier studies have related brain kinetics and head kinematics to concussion and traumatic brain injury (TBI). …