Mechanical Engineering Commons^™

Test 2187: Case Ih Steiger 500 Quadtrac, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2186: Case Ih Steiger 470 Quadtrac, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Fundamental Principles Of Tremor Propagation In The Upper Limb, Andrew D. Davidson, Steven Knight Charles

Faculty Publications

Although tremor is the most common movement disorder, there exist few effective tremor-suppressing devices, in part because the characteristics of tremor throughout the upper limb are unknown. To clarify, optimally suppressing tremor requires a knowledge of the mechanical origin, propagation, and distribution of tremor throughout the upper limb. Here we present the first systematic investigation of how tremor propagates between the shoulder, elbow, forearm, and wrist. We simulated tremor propagation using a linear, time-invariant, lumped-parameter model relating joint torques and the resulting joint displacements. The model focused on the seven main degrees of freedom from the shoulder to the wrist …

Optimized Endpoint Delivery Via Unmanned Aerial Vehicles, Fuad Gazal

All Graduate Theses, Dissertations, and Other Capstone Projects

Unmanned Aerial Vehicles (UAVs) are remotely piloted aircraft with a range of varying applications. Though early adoption of UAVs focused on military applications, surveillance, photography, and agricultural applications are presently on the rise. This work aims to ascertain how UAVs may be employed to elicit deceased transportation times, increased power efficiency, and improved safety. Resulting in optimized end point delivery. A combination of tools and techniques, involving a mathematical model, UAV simulations, redundant control systems, and custom designed electrical and mechanical components were used towards reaching the goal of a 10-kilogram maximum payload delivered 10 miles under 30 minutes. Two …

Fourth-Generation Fan Assessment Numeration System (Fans) Design And Performance Specifications, Michael P. Sama, George B. Day, Laura M. Pepple, Richard S. Gates

Biosystems and Agricultural Engineering Faculty Publications

The Fan Assessment Numeration System (FANS) is a measurement device for generating ventilation fan performance curves. Three different-sized FANS currently exist for assessing ventilation fans commonly used in poultry and livestock housing systems. All FANS consist of an array of anemometers inside an aluminum shroud that traverse the inlet or outlet of a ventilation fan. The FANS design has been updated several times since its inception and is currently in its fourth-generation (G4). The current design iteration (FANS-G4) is reported in this article with an emphasis on the hardware and software control, data acquisition systems, and operational reliability. Six FANS-G4 …

Effect Of Vibration Of Unconsolidated Sand On The Performance Of Interferometric Vibration Sensors, Cody Berrey

Electronic Theses and Dissertations

Interferometric vibration sensors are widely used for ground vibration measurements where traditional contact sensors are not desired. Laser Doppler vibrometers (LDV) and digital speckle pattern interferometers are studied in this thesis. The working principle of laser Doppler vibrometry and digital shearography is described. The effect of vibration of the unconsolidated sand on the performance of both sensors is experimentally investigated.

The vibration of unconsolidated sand can cause an increase of noise in the laser Doppler vibrometer output and cause speckle decorrelation in digital speckle pattern interferometry (referred to as digital shearography). An experimental investigation of the effect of varying the …

Local Transient Characterization Of Thermofluid Heat Transfer Coefficient At Solid-Liquid Nano-Interfaces, Mehrdad Mehrvand

Electronic Theses and Dissertations

The demands for increasingly smaller, more capable, and higher power density technologies in microelectronics, energy, or aerospace systems have heightened the need for new methods to manage and characterize extreme heat fluxes (EHF). Microscale liquid cooling techniques are viewed as a promising solution for removing heat from high heat flux (HHF) systems. However, there have been challenges in physical understanding and predicting local thermal transport at the interface of micro and nanoscale structures/devices due to ballistic effects and complex coupling of mass, momentum, and energy transport at the solid-liquid-vapor interfaces over multiple time and length scales. Moreover, it's challenging to …

Computational Fluid Dynamics Study Of Thromboembolism As A Function Of Shunt Size And Placement In The Hybrid Norwood Palliative Treatment Of Hypoplastic Left Heart Syndrome, John Seligson

Electronic Theses and Dissertations

The Hybrid Norwood procedure has emerged as a promising alternative palliative first stage treatment for infants with Hypoplastic Left Heart Syndrome (HLHS). The procedure is done to provide necessary blood flow to the pulmonary and systemic regions of the body. The procedure can affect hemodynamic conditions to be pro-thrombotic, and thrombus particles can form and release from the vessel walls and enter the flow. Assuming these particles are formed and released from the shunt surface, a Computational Fluid Dynamics (CFD) model can be used to mimic the patient's vasculature geometry and predict the occurrence of embolization to the carotid or …

Hydrodynamic Measurements Of The Flow Structure Emanating From A Multi-Row Film Cooling Configuration, Michael Voet

Electronic Theses and Dissertations

The demand for more power is rapidly increasing worldwide. Attention is turned to increasing the efficiency of modern methods for power generation. Gas turbines provide 35% of the power demands within the United States. Efficiency of gas turbines is defined in an ideal sense by the thermal efficiency of the Brayton Cycle. The overall efficiency of a gas turbine can be increased while simultaneously maximizing specific work output, by increasing the turbine inlet temperature. However, even with the advancements in modern materials in terms of maximum operating temperature, various components are already subjected to temperatures higher than their melting temperatures. …

Enhanced Handheld Engine Ethanol Study, Charindu Kariyawasan Jalath Thanthree

All Graduate Theses, Dissertations, and Other Capstone Projects

This study examined consumer and professional grade handheld engines. Twenty-four consumer grade 50 hour Emissions Determination Period (EDP) trimmers and 24 professional grade 300 hour EDP backpack leaf blowers were run on four different ethanol fuel concentrations; E0, E10, E15, and E20. Six engines of each type were run on each of the fuel blends through their full EDP.

All engines were broken-in and adjusted to manufacturer specifications on E0. Then engines were emissions tested on E0 to provide a baseline and to determine the rich to lean order of the engines. Next, the leanest operating engine received E20 and …

Trustworthiness Requirements For Manufacturing Cyber-Physical Systems, Radu F. Babiceanu, Remzi Seker

Publications

Distributed manufacturing operations include cyber-physical systems vulnerable to cyber-attacks. Long time not considered a priority, cybersecurity jumped to the forefront of manufacturing concerns due to the need to network together legacy, newer equipment, and entire operation centers. This paper proposes trustworthiness solutions for integrated manufacturing physical-cyber worlds, where trustworthiness is defined to complement system dependability requirements with cybersecurity requirements, such that the resulting manufacturing cyber-physical system delivers services that can justifiably be trusted. Acknowledging the inevitability of cyber-attacks, the paper models the cybersecurity component using the resilient systems framework, where system resilience is viewed as preservation of a required state …

Age-Related Differences In The Lumbopelvic Kinematics During The Trunk Motions In The Anatomical Planes, Milad Vazirian

Theses and Dissertations--Biomedical Engineering

Management and control of the low back pain as an important health problem in the industrial societies necessitates to investigate how the risk of this disease is affected by aging. Since the abnormalities of the lumbopelvic kinematics are related to the existence or risk of low back injuries, the objective of this dissertation was set to find the age-related differences in lumbopelvic kinematics when performing basic trunk motions reaching to range of motion in different anatomical planes.

A cross-sectional study was designed where sixty asymptomatic individuals between 20–70 years old with no confounding health condition, no current or previous highly …

Analytical Strip Method For Thin Cylindrical Shells, John T. Perkins

Theses and Dissertations--Civil Engineering

The Analytical Strip Method (ASM) for the analysis of thin cylindrical shells is presented in this dissertation. The system of three governing differential equations for the cylindrical shell are reduced to a single eighth order partial differential equation (PDE) in terms of a potential function. The PDE is solved as a single series form of the potential function, from which the displacement and force quantities are determined. The solution is applicable to isotropic, generally orthotropic, and laminated shells. Cylinders may have simply supported edges, clamped edges, free edges, or edges supported by isotropic beams. The cylindrical shell can be stiffened …

Target Read Operation Of Passive Ultra High Frequency Rfid Tag In A Multiple Tags Environment, Zi Qin Phua

Theses and Dissertations--Mechanical and Aerospace Engineering

Passive ultra-high frequency (UHF) radio frequency Identification (RFID) has emerged as a promising solution for many industrial applications. Passive UHF systems are relatively inexpensive to implement and monitor, as no line of sight is required for the communication. There are several advantages to using a passive RFID system. For example, no internal power source is required to activate the tags, and lower labor costs and efficient multitasking operations are expected in a long term scenario. However, due to factors such as tag-to-tag interference and inaccurate localization, RFID tags that are closely spaced together are difficult to detect and program accurately …

A Physics-Based Approach To Modeling Wildland Fire Spread Through Porous Fuel Beds, Tingting Tang

Theses and Dissertations--Mechanical and Aerospace Engineering

Wildfires are becoming increasingly erratic nowadays at least in part because of climate change. CFD (computational fluid dynamics)-based models with the potential of simulating extreme behaviors are gaining increasing attention as a means to predict such behavior in order to aid firefighting efforts. This dissertation describes a wildfire model based on the current understanding of wildfire physics. The model includes physics of turbulence, inhomogeneous porous fuel beds, heat release, ignition, and firebrands. A discrete dynamical system for flow in porous media is derived and incorporated into the subgrid-scale model for synthetic-velocity large-eddy simulation (LES), and a general porosity-permeability model is …

Adaptive Scheduling For Operating Room Management, Honghan Ye

Theses and Dissertations--Mechanical and Aerospace Engineering

The perioperative process in hospitals can be modelled as a 3-stage no-wait flow shop. The utilization of OR units and the average waiting time of patients are related to makespan and total completion time, respectively. However, minimizations of makespan and total completion time are NP-hard and NP-complete. Consequently, achieving good effectiveness and efficiency is a challenge in no-wait flow shop scheduling. The average idle time (AIT) and current and future idle time (CFI) heuristics are proposed to minimize makespan and total completion time, respectively. To improve effectiveness, current idle times and future idle times are taken into consideration …

The Limits & Effects Of Draw On Properties And Morphology Of Pan-Based Precursor And The Resultant Carbon Fibers, Sarah Edrington

Theses and Dissertations--Mechanical and Aerospace Engineering

The process, structure, and property relationship of PAN fiber as a precursor to carbon fiber was studied. The limitations of stable spinning and property improvement associated with hot draw in solution spinning were found and quantified. Conditions were varied to generated precursor fiber up to the limit of draw, from which actual samples were collected for thermal conversion to carbon fiber. Samples of PAN and subsequent carbon fiber were characterized using tensile testing and x-ray analysis. The effects of draw on modulus and break stress, as well as the orientation of the crystalline structure of both parent precursor and resultant …

Shape Memory Behavior Of Dense And Porous Niti Alloys Fabricated By Selective Laser Melting, Soheil Saedi

Theses and Dissertations--Mechanical and Aerospace Engineering

Selective Laser Melting (SLM) of Additive Manufacturing is an attractive fabrication method that employs CAD data to selectively melt the metal powder layer by layer via a laser beam and produce a 3D part. This method not only opens a new window in overcoming traditional NiTi fabrication problems but also for producing porous or complex shaped structures. The combination of SLM fabrication advantages with the unique properties of NiTi alloys, such as shape memory effect, superelasticity, high ductility, work output, corrosion, biocompatibility, etc. makes SLM NiTi alloys extremely promising for numerous applications.

The SLM process parameters such as laser power, …

Computational Investigation Of Transmural Differences In Left Ventricular Contractility And Hydrogel Injection Treatment For Myocardial Infarction, Hua Wang

Theses and Dissertations--Mechanical and Aerospace Engineering

Heart failure (HF) is one of the leading causes of death and impacts millions of people throughout the world. Recently, injectable hydrogels have been developed as a potential new therapy to treat myocardium infarction (MI). This dissertation is focused on two main topics: 1) to gain a better understanding the transmural contractility in the healthy left ventricle (LV) wall and 2) investigate the efficacy of the hydrogel injection treatment on LV wall stress and function. The results indicate that a non-uniform distribution of myocardial contractility in the LV wall provide a better representation of normal LV function. The other important …

Data-Driven Adaptive Reynolds-Averaged Navier-Stokes K - Ω Models For Turbulent Flow-Field Simulations, Zhiyong Li

Theses and Dissertations--Mechanical and Aerospace Engineering

The data-driven adaptive algorithms are explored as a means of increasing the accuracy of Reynolds-averaged turbulence models. This dissertation presents two new data-driven adaptive computational models for simulating turbulent flow, where partial-but-incomplete measurement data is available. These models automatically adjust (i.e., adapts) the closure coefficients of the Reynolds-averaged Navier-Stokes (RANS) k-ω turbulence equations to improve agreement between the simulated flow and a set of prescribed measurement data.

The first approach is the data-driven adaptive RANS k-ω (D-DARK) model. It is validated with three canonical flow geometries: pipe flow, the backward-facing step, and flow around an airfoil. For all 3 test …

Torque Response Of Thin-Film Ferromagnetic Prisms In Uniform Magnetic Fields At Macro And Micro Scales, Soroosh Torabi

Theses and Dissertations--Mechanical and Aerospace Engineering

The non-contact nature of magnetic actuation makes it useful in a variety of microscale applications, from microfluidics and lab-on-a-chip devices to classical MEMS or even microrobotics. Ferromagnetic materials like nickel are particularly attractive, because they can be easily deposited and patterned using traditional lithography-based microscale fabrication methods. However, the response of ferromagnetic materials in a magnetic field can be difficult to predict. When placed in a magnetic field, high magnetization is induced in these ferromagnetic materials, which in turn generates force and/or torque on the ferromagnetic bodies. The magnitude and direction of these forces are highly dependent on the type …

Effects Of Temperature, Orientation, Load Level And Indenter Shape On The Indentation Response Of Niti-Based Shape Memory Alloys, Peizhen Li

Theses and Dissertations--Mechanical and Aerospace Engineering

Owing the capability of recovering large deformations through reversible phase transformation, shape memory alloys (SMAs) are well-known for their unique behaviors such as shape memory effect (SME) and superelasticity (SE), which can also be characterized by instrumented indentation techniques. Nickel titanium (NiTi) SMAs have been extensively used for nano/micro-indentation studies and widely applied to biomedical and other elaborate medical devices.

In this study, indentation responses of NiTi, NiTiHf, NiTiHfPd and NiTiHfCu alloys were investigated using spherical and Berkovich indenters at room temperature. Spherical and Berkovich indentation hardness, modulus, and work/depth recoverable ratio of these NiTi-based alloys were revealed as a …

Analytical And Boundary Element Solutions Of Bulk Reacting Lined Ducts And Parallel-Baffle Silencers, Jundong Li

Theses and Dissertations--Mechanical and Aerospace Engineering

Lined silencers of various configurations are used to attenuate the noise from building HVAC equipment, gas turbines, and other machinery. First-mode analytical solutions are presented for sound attenuation along rectangular lined ducts, parallel-baffle silencers, and circular lined ducts. The sound absorptive lining is treated using a bulk property model. The analytical solutions entail solving a nonlinear characteristic equation in the transverse direction after the rigid-wall boundary condition is applied. The solution is compared to the boundary element solution and a local impedance analytical solution for several test cases.

A Framework And Metrics For Sustainable Manufacturing Performance Evaluation At The Production Line, Plant And Enterprise Levels, Aihua Huang

Theses and Dissertations--Mechanical and Aerospace Engineering

Sustainable manufacturing is becoming increasingly important due to scarcity of natural resources, stricter regulations and increasing customer demand for sustainable products. Sustainable manufacturing involves the use of sustainable processes and systems to produce more sustainable products. In order to meet these demands for sustainable products, manufacturing companies have to adopt numerous strategies to achieve sustainable manufacturing. The approach for evaluating sustainable products and processes have been investigated in previous work where product/process sustainability indices were proposed. However, no comprehensive methods are available for sustainable manufacturing performance evaluation at the system level. This work aims to develop two alternate methods for …

Simulation Of Horse-Fence Contact And Interaction Affecting Rotational Falls In The Sport Of Eventing, Gregorio Robles Vega

Theses and Dissertations--Mechanical and Aerospace Engineering

Rotational falls, or somersault falls, have led to serious and fatal injuries during the cross-country phase of Eventing competitions. Research to improve the safety of the sport began in 2000 after five fatal injuries occurred in the 1999 Eventing season. These efforts led to safety devices such as air jackets, improved helmets, and frangible/deformable fences. The focus of this thesis is to develop a more complete understanding of the horse-fence interaction as the approach motion transitions to a rotational fall. To achieve this, a large distribution of inertial properties was compiled through the development of a cylinder-based inertia approximation and …

Advances In Multi-Agent Flocking: Continuous-Time And Discrete-Time Algorithms, Brandon Wellman

Theses and Dissertations--Mechanical and Aerospace Engineering

We present multi-agent control methods that address flocking in continuous-time and discrete-time settings. The method is decentralized, that is, each agents controller relies on local sensing to determine the relative positions and velocities of nearby agents. In the continuous-time setting, each agent has double-integrator dynamics. In the discrete-time setting, each agent has the discrete-time double-integrator dynamics obtained by sampling the continuous-time double integrator and applying a zero-order hold on the control input. We demonstrate using analysis, numerical simulations, and experimental demonstrations that agents using the flocking methods converge to flocking formations and follow the centralized leader (if applicable).

Investigation Of An Axial Flow Rotary Valve Seal, Joseph K. Stieha

Theses and Dissertations--Mechanical and Aerospace Engineering

This thesis investigates potential materials to be used in the rotary sealing industry that provide low power loss and minimize cost. The studied rotary valve utilizes slots that act as timing valves to allow for flow axially, through the seal face, at particular times within a heat pump cycle. This investigation examines various combinations of multiple PTFE materials, plastics, and soft metals that have been proven to provide low friction coefficients. Leakage and wear requirements are stated for the future use of the rotary valve and are used to determine the effectiveness of sealing the fluid while examining the power …

Development Of A Supplier Segmentation Method For Increased Resilience And Robustness: A Study Using Agent Based Modeling And Simulation, Adam J. Brown

Theses and Dissertations--Mechanical and Aerospace Engineering

Supply chain management is a complex process requiring the coordination of numerous decisions in the attempt to balance often-conflicting objectives such as quality, cost, and on-time delivery. To meet these and other objectives, a focal company must develop organized systems for establishing and managing its supplier relationships. A reliable, decision-support tool is needed for selecting the best procurement strategy for each supplier, given knowledge of the existing sourcing environment. Supplier segmentation is a well-established and resource-efficient tool used to identify procurement strategies for groups of suppliers with similar characteristics. However, the existing methods of segmentation generally select strategies that optimize …

Impedance-To-Scattering Matrix Method For Large Silencer Analysis, Peng Wang

Theses and Dissertations--Mechanical and Aerospace Engineering

Large silencers used in the power generation industry usually have a very large cross section at the inlet and outlet. Higher-order modes will populate the inlet and outlet even at very low frequencies. Although the silencer itself is often modeled by a three-dimensional analysis tool such as the boundary element method (BEM) or finite element method (FEM), a direct computation of the transmission loss (TL) from the BEM or FEM model can be challenging without incorporating certain forms of modal expansion.

A so-called “impedance-to-scattering matrix method” is proposed to extract the modes at the inlet and outlet from the BEM …

A Transfer Matrix Approach To Determine The Low Frequency Insertion Loss Of Enclosures Including Applications, Shujian He

Theses and Dissertations--Mechanical and Aerospace Engineering

Partial enclosures are commonly used to reduce machinery noise. However, it is well known in industry that enclosures sometimes amplify the sound at low frequencies due to strong acoustic resonances compromising the performance. These noise issues are preventable if predicted prior to prototyping and production. Though boundary and finite element approaches can be used to accurately predict partial enclosure insertion loss, modifications to the model require time for remeshing and solving. In this work, partial enclosure performance at low frequencies is simulated using a plane wave transfer matrix approach. Models can be constructed and the effect of design modifications can …