Mechanical Engineering Commons^™

Investigation Of The Use Of 3-D Printer Platform As Building Block For Rapid Design Of Research And Manufacturing Tool, Handy Chandra

Dissertations, Master's Theses and Master's Reports

This thesis attempts to show how an open source 3-D printer platform, the self replicating rapid prototype (RepRap), could be used to accelerate the development of research and manufacturing tools. Two projects are shown as examples, both utilizing components of the 3-D printer platform.

The first project is to develop an instrument capable of performing automated large-area four-point probe measurements. A modified RepRap 3-D Printer with a four-point probe in place of the 3-D printer head is utilized as a precision positioning platform. The printer together with custom designed measurement circuit and software performs automated measurement on multiple points on …

Incorporation Of Higher Carbon Number Alcohols In Gasoline Blends For Application In Spark-Ignition Engines, Kristina Lawyer

Dissertations, Master's Theses and Master's Reports

The 2007 U.S. Renewable Fuel Standard (RFS2) requires an increase in the use of advanced biofuels up to 36 billion gallons by 2022. Higher carbon number alcohols, in addition to cellulosic ethanol and synthetic biofuels, could be used to meet this demand while adhering to the RFS2 corn-based ethanol limitation. Alcohols of carbon numbers 2 through 8 are chosen based on their chemical and engine-related properties.

Blend comparison metrics are developed from automotive industry trends, consumer expectations, U.S. fuel legislation, and engine requirements. The metrics are then used to create scenarios by which to compare higher alcohol fuel blends to …

Impact Of E20 Fuel On A High-Performance, Two-Stroke Engine, Jon Gregory Loesche

Dissertations, Master's Theses and Master's Reports

The purpose of this project was to explore the emissions, combustion, and performance effects of running a gasoline/ethanol fuel mixture of 20 percent by volume (E20) in a fuel-injected, two-stroke engine. The engine was operated at five engine speeds that corresponded with the EPA 5-mode emissions test for snowmobile engines. Single parameter sweeps were conducted along with a preliminary recalibration of the test engine at two E0 target values (lambda and mid-pipe temperature) using E20 fuel.

Baseline testing showed that running E20 fuel produced a leaner air/fuel mixture compared to E0, resulting in higher lambda values for all modes and …

Frontal Crash Analysis Of A Conformable Cng Tank Using Finite Element Analysis, Datta Sandesh Manjunath

Dissertations, Master's Theses and Master's Reports

The purpose of this study is to computationally model and analyze a Conformable Compressed Natural Gas (CNG) fuel tank for frontal crashes using Finite Element Analysis. Researchers have developed a CNG fuel tank, which is conformable, non-conventional and non-cylindrical. This tank increases cost efficiency, volumetric efficiency and cargo efficiency in CNG vehicle applications. A lightweight pickup truck (2015 Chevrolet Silverado) has been used to integrate the CNG tanks and field-testing has been conducted to demonstrate the application.

The report mainly focuses on the effective finite element modeling of the chassis, brackets and tanks using HYPERMESH and RADIOSS. The frontal crash …

Minimizing Run Time Of Finite Element Analyses: Applications In Conformable Cng Tank Modeling, Paul M. Roehm

Dissertations, Master's Theses and Master's Reports

REL Inc. has proposed a CNG tank that deviates from typical cylindrical storage methods. The goal of REL working with Michigan Tech is to minimize mass and meet NGV2 safety standards for pressure and drop testing for this tank.

The model has undulated outer surfaces and Schwarz P-surface internal geometry. To accurately mesh this, a small element size is necessary; this creates a model with millions of elements. In explicit analyses, this requires a large amount of computational resources to run.

This report focuses on methods to reduce model run time without reducing accuracy. Methods covered include creating symmetric building …

Model-Based Control Of Hybrid Electric Powertrains Integrated With Low Temperature Combustion Engines, Ali Soloukmofrad

Dissertations, Master's Theses and Master's Reports

Powertrain electrification including hybridizing advanced combustion engines is a viable cost-effective solution to improve fuel economy of vehicles. This will provide opportunity for narrow-range high-efficiency combustion regimes to be able to operate and consequently improve vehicle’s fuel conversion efficiency, compared to conventional hybrid electric vehicles (HEV)s. Low temperature combustion (LTC) engines offer the highest peak brake thermal efficiency reported in literature, but these engines have narrow operating range. In addition, LTC engines have ultra-low soot and nitrogen oxides (NOx) emissions, compared to conventional compression ignition and spark ignition (SI) engines. This dissertation concentrates on integrating the LTC engines (i) in …

Development Of A High-Fidelity Model And Kalman Filter Based State Estimator For Simulation And Control Of Nox Reduction Performance Of A Scr Catalyst On A Dpf, Venkata Rajesh Chundru

Dissertations, Master's Theses and Master's Reports

Reduction of emissions and improving the fuel consumption are two prime research areas in Diesel engine development. The present after-treatment systems being used for emissions control include diesel oxidation catalyst (DOC) for NO, HC and CO oxidation along with catalyzed particulate filters for PM (particulate matter) and selective catalytic reduction (SCR) for controlling NOx emissions. Recently an after-treatment system called SCR catalyst on a DPF capable of simultaneously reducing both NOx and PM emissions has been developed in order to reduce the overall size of the after-treatment system.

The goal of this proposed research is to create a state estimator …

Performance Of Hard Disk Drives In High Noise Environments, Trinoy Dutta

Dissertations, Master's Theses and Master's Reports

Digital information stored in rotational media, such as Hard Disk Drives (HDD) needs to be reliable and readily accessible. Various studies have been performed on the modal analysis of HDDs and the noise emitted during operation. Analysis performed by Siemens Corporation, IBM and Tyco Fire Protection Products show that HDDs are sensitive to noise. This report initially focusses on identifying the critical frequency ranges and the levels of noise where the performance of the drives reduces. A series of tests have been performed using pink noise at one-third octave frequency bands at sound pressure levels ranging from 80 dB to …

Simulation Study On Effect Of Gas Charging And Egr In A Dual-Fuel Engine, Satyavenkata Naga Sai Sharath Gorthy

Dissertations, Master's Theses and Master's Reports

Natural gas combined with diesel as micro pilot has the capabilities of achieving lower NOx and soot emissions. Optimization of the combustion process in engines with natural gas and diesel micro-pilot is essential to achieve higher efficiencies and loads. Gas charging (intake air boosting) and EGR are two technologies which when implemented in the natural gas-diesel engines, provide the opportunity to achieve higher efficiencies and loads and low emissions. Simulation study is one of the approaches to investigate the extent and effects of gas charging and EGR on the performance of the engine. With the rapid improvements over the past …

Precision Control Of Flow Rate In Microfluidic Channels Using Photoresponsive Soft Polymer Actuators, Colm Delaney, Peter Mccluskey, Simon Coleman, Jeffrey Whyte, Nigel Kent, Dermot Diamond

Articles

A novel approach that allows control of flow in microfluidic channels with unsurpassed performance using light is described. Valve structures have been created using photoresponsive hydrogels based on spiropyran-functionalised pNIPAAm hydrogels photopolymerised around pillar structures within the channels. Valve actuation is controlled from outside the fluidic system using externally located LEDs. Highly precise and accurate flow rates can be selected by passing real-time flow rate measurements into a PID algorithm. The optimised algorithm also minimises overshoot of the selected flow rate, eliminates flow rate drift, and improves the system response time. In addition to the dramatic improvements in flow rate …

Novel Design And Synthesis Of Nanostructured Electrode Materials For Advanced Lithium Ion Batteries, Zhiqiang Xie

LSU Master's Theses

Nowadays, rechargeable lithium-ion batteries (LIBs) have been widely used as energy storage devices for portable electronic devices. The increasing demand for their emerging applications in hybrid electric vehicles (HEVs) and electric vehicles (EVs) requires us to develop LIBs with higher energy density and power density. However, both the commercial cathode material (LiCoO2) and anode material (graphite) exhibit low specific capacity and poor rate capability, which severely hinder the practical application of lithium-ion batteries for transportation. This thesis mainly includes four research works on novel design and synthesis of nanostructured electrode materials for advanced lithium-ion batteries. To improve the electrochemical performances …

Design Of Electrical Layout Of Offshore Wind Farms, Shirshak K. Dhali, Mahidhar Nandigam

Electrical & Computer Engineering Faculty Publications

The cost and efficiency of offshore wind farms are determined by a variety of factors which include the type of electrical system (AC or DC), transmission length, transmission voltage, rated power, wind turbine type, farm topology, and wind speed. Since the design variable space is large for such problems, computational optimization is necessary to find an optimal solution. This paper discusses a design methodology to determine the optimal values of components to minimize the cost of an offshore wind farm. The cost, loss, reliability models, and the application of geometric programing for optimization of the layout and configuration of an …

Thermomechanical Modeling Of Polymerica Actuators, Qianxi Yang

LSU Doctoral Dissertations

In this dissertation, the application of smart polymers as actuators was investigated, with focuses on shape memory polymers and twisted-then-coiled artificial muscles. Thermomechanical models have been developed for various polymeric actuators, so as to facilitate interpretation of the underlying mechanisms and to provide guidance for future design. The classical one-way shape memory effect in amorphous shape memory polymers was first reproduced. The amorphous shape memory polymer was treated as a frozen-phase matrix with active-phase inclusions embedded in it. A phase evolution law was proposed from the physics perspective and the Mori-Tanaka approach was used to predict the effective mechanical properties. …

The Evaluation And Implementation Of Magnetic Fields Suitable For Biaxial Cyclic Testing Of Magnetorheological Elastomers, Dave Gorman

Doctoral

This thesis addresses the current lack of specification of magnetic fields currently used in the physical testing of Magnetorheological Elastomers MREs as well as providing the first comparative test results for MREs subject to both biaxial and uniaxial cyclic loading in the same magnetic field. In order to design an electromagnetic array capable of generating a suitable magnetic field for the cyclic biaxial testing of MREs, a review of currently used magnetic fields for uniaxial testing of MREs was carried out and a suitable array was modelled and evaluated with both 2D and 3D FEA software. Once the FEA analysis …

Developing A Low-Cost Force Treadmill Via Dynamic Modeling, Chih-Yuan Hong, Lan-Yuen Guo, Rong Song, Mark L. Nagurka, Jia-Li Sung, Chen-Wen Yen

Mechanical Engineering Faculty Research and Publications

By incorporating force transducers into treadmills, force platform-instrumented treadmills (commonly called force treadmills) can collect large amounts of gait data and enable the ground reaction force (GRF) to be calculated. However, the high cost of force treadmills has limited their adoption. This paper proposes a low-cost force treadmill system with force sensors installed underneath a standard exercise treadmill. It identifies and compensates for the force transmission dynamics from the actual GRF applied on the treadmill track surface to the force transmitted to the force sensors underneath the treadmill body. This study also proposes a testing procedure to assess the GRF …

Metal Cutting And Manufacturing Economics Project For Freshmen, Hüseyin Sarper, Nebojsa I. Jaksic, Linda Vahala

Electrical & Computer Engineering Faculty Publications

This paper describes a laboratory experiment and a team project to teach manufacturing concepts to new students. This project is one of two team projects of 1.5 credit portion of a two-credit course in exploration of engineering and technology. This course teaches students skills they need late and teamwork is a major skill that they acquire. They organize into a group with specialized responsibilities for the purpose of calculating the total production time and cost of a manufactured part using turning, drilling, and milling operations. Students also learn or improve spreadsheet skills while performing data entry and necessary machining calculations. …

Careers In Engineering Lesson Plan, Lindsay Snowden

ENgaging Educators in Renewable enerGY (ENERGY): Lesson Plans & Slideshows (2017-2019)

Careers in Engineering Lesson Plan. The activity is to create a version of a robotic hand with the supplies provided,

Solar Irradiance Forecasting And Implications For Domestic Electric Water Heating, Christopher Nutter

College of Graduate Studies: Theses & Dissertations

As the effects of burning fossil fuels continues to present its prevalence, the interests in alternative forms of energy is expanding. Within the home, the domestic electrical water heater accounts for approximately 17% of its energy consumption. Reducing the amount of energy required to produce hot water from this thermal system alone can have a significant effect on reducing its carbon footprint. In this presented work, a modeled domestic electrical water heater was supplied photovoltaic and on-grid electrical power to increase its energy efficiency. As photovoltaic (PV) energy is directly related to solar irradiation, it is important to receive accurate …

Mentoring Initial Research, Abigail Lisjak, Tim Leonard, Adam Foster, Patrick Gray

Sustainability and Connectivity

This document details the initial research the group gathered as the problem statement was being refined. Some of this research will be used to inform future elements of the project.

Proceedings Of The 17th Annual Early Career Technical Conference (Front Matter), Ectc Coordinating Committee

Early Career Technical Journal (ECTJ)

Proceedings of the 17th Annual Early Career Technical Conference, November 3, 2017. School of Engineering, University of Alabama at Birmingham, Birmingham, Alabama; pp. i-xi

Section 1: Design, Ectc Coordinating Committee

Early Career Technical Journal (ECTJ)

Proceedings of the 17th Annual Early Career Technical Conference, November 3, 2017. School of Engineering, University of Alabama at Birmingham, Birmingham, Alabama; pp. 1-26

Section 3: Robitics & Controls, Ectc Coordinating Committee

Early Career Technical Journal (ECTJ)

Proceedings of the 17th Annual Early Career Technical Conference, November 3, 2017. School of Engineering, University of Alabama at Birmingham, Birmingham, Alabama; pp. 57-78

Path Tracking Using Model Based Control Of Rigid 5 Bar Mechanism, Jacob Davis, Ayse Tekes

Early Career Technical Journal (ECTJ)

Section 1: Design; pp. 3-7

Section 6: Miscellaneous, Ectc Coordinating Committee

Early Career Technical Journal (ECTJ)

Proceedings of the 17th Annual Early Career Technical Conference, November 3, 2017. School of Engineering, University of Alabama at Birmingham, Birmingham, Alabama; pp. 143-158

Section 4: Numerical Methods, Ectc Coordinating Committee

Early Career Technical Journal (ECTJ)

Proceedings of the 17th Annual Early Career Technical Conference, November 3, 2017. School of Engineering, University of Alabama at Birmingham, Birmingham, Alabama; pp. 79-112

A Study Of Two Different Spider Spring Balancers Used For Cryocooler Operations, Madhurima Maddela, Samuel Misko, Lee Moradi

Early Career Technical Journal (ECTJ)

Section 1: Design; pp. 21-25

Repurposing Waste Heat Energy For High Temperature Applications, James Ackley, Jonathan Atkinson, Edwin Garcia, Laura Ruhala, Sathish Gurupatham

Early Career Technical Journal (ECTJ)

Section 2: Energy; pp. 29-33

Comparison Of High Bypass Turbofan Engine Cycle Analyses – A Case Study, Christopher Roper, Skyler Bagley, Alain Santos, Adeel Khalid

Early Career Technical Journal (ECTJ)

Section 2: Energy; pp. 34-41

Modeling And Evaluation Of Business- Engineering Complex Energy Performance, Qing Mu, Hessam Taherian

Early Career Technical Journal (ECTJ)

Section 2: Energy; pp. 42-47

The Effect Of Tank Volume On Performance Of An Evacuated Tube Solar Water Heater, Azadeh Sobrabi, Farzad Veysi, Hessam Taherian

Early Career Technical Journal (ECTJ)

Section 2: Energy; pp. 48-55