Materials Science and Engineering Commons^™

Investigation Of Electric Field–Induced Structural Changes At Fe-Doped Srtio3 Anode Interfaces By Second Harmonic Generation, David Ascienzo, Haochen Yuan, Steven Greenbaum, Thorsten J. Bayer, Russell A. Maier, Jian-Jun Wang, Clive A. Randall, Elizabeth C. Dickey, Haibin Zhao, Yuhang Ren

Publications and Research

We report on the detection of electric field–induced second harmonic generation (EFISHG) from the anode interfaces of reduced and oxidized Fe-doped SrTiO3 (Fe:STO) single crystals. For the reduced crystal, we observe steady enhancements of the susceptibility components as the imposed dc-voltage increases. The enhancements are attributed to a field-stabilized electrostriction, leading to Fe:Ti-O bond stretching and bending in Fe:Ti-O6 octahedra. For the oxidized crystal, no obvious structural changes are observed below 16 kV/cm. Above 16 kV/cm, a sharp enhancement of the susceptibilities occurs due to local electrostrictive deformations in response to oxygen vacancy migrations away from the anode. Differences between …

Material Evaluation: Self Damping Wire Sd/Acsr Conductor Failures, Daniel F. Weyer

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Following numerous 954 ACSR SD Wire failures from 2010 to 2012, Nebraska Public Power District (NPPD) implemented an inspection program to determine the extent of condition for this type of widely used conductor. NPPD transmission system includes over 2000 miles of this particular conductor.

Transmission line splices are installed every 15-20 spans, with failures being located in a span containing a splice. NPPD worked with Kinectrics to complete electromagnetic field inspections for three days in 2013, with retesting performed in 2015. Throughout this inspection of 54 spans of conductor, 36 were found to have deterioration and corrosion.

Over 80% of …

Metal-Organic Frameworks As Potential Platforms For Carbon Dioxide Capture And Chemical Transformation, Wenyang Gao

USF Tampa Graduate Theses and Dissertations

The anthropogenic carbon dioxide (CO₂) emission into the atmosphere, mainly through the combustion of fossil fuels, has resulted in a balance disturbance of the carbon cycle. Overwhelming scientific evidence proves that the escalating level of atmospheric CO₂ is deemed as the main culprit for global warming and climate change. It is thus imperative to develop viable CO₂ capture and sequestration (CCS) technologies to reduce CO₂ emissions, which is also essential to avoid the potential devastating effects in future. The drawbacks of energy-cost, corrosion and inefficiency for amine-based wet-scrubbing systems which are currently used in industry, …

Advances And Prospects Of Lithium-Sulfur Batteries, Shou-Yi Yuan, Ying Pang, Li-Na Wang, Yong-Gang Wang, Yong-Yao Xia

Journal of Electrochemistry

Lithium-sulfur batteries have recently attracted worldwide attention due to the high specific theoretical energy density of sulfur cathode (2600 Wh⋅kg^-1), low cost and wide availability of sulfur. However, the practical application of lithium-sulfur batteries has been hindered by several challenges, such as the shuttling of polysulfide intermediates, the large volume expansion of sulfur during charge/discharge and the dendrites formation on lithium anode. Foremost among these is the shuttling effect arising from the dissolution of lithium polysulfides intermediate into the electrolyte from the cathode reaction and their diffusion to the anode where they react with metal lithium to form …

Research Progress In Cycle Stability Of Silicon Based Li-Ion Battery Anodes, Ze-Liang Guo, Hui Wu

Journal of Electrochemistry

Silicon(Si), with the highest specific capacity currently known, is a promising anode material for Li-ion battery. However, in the charging and discharging process, with Li atoms inserting into and breaking out of the Si crystal lattices, the Si anode undergoes enormous volume expansion and contraction, ending in pulverization. The fact that the specific capacity of bulk Si anodes drop quickly is a challenging problem. In this review, we summarize recent progresses in Si anode. We concern about the nanostructure of silicon, cooperation of silicon with other additives and macrostructure design of anodes. We discuss strengths and shortcomings of different methods, …

Effects Of Lithium Salts On The Properties Of Hyperbrandched/Comb-Like Composite Polymer Electrolytes, Xian-Lei Hu, Xiao-Xu Liang, Ming-Qiu Zhang, Ruo-Xin Zhang, Li-Ping Zhang, Wen-Hong Ruan

Journal of Electrochemistry

Based on the chemical characteristics of the hydroxyl group of PVA side-chain, the hyperbrandched poly(amine-ester) (HBPAE) was used to hypergraftingly pretreated nano-silica (SiO₂) and polyving akohol (PVA). And different lithium salts were added to fabricate the SiO₂-g-HBPAE/PVA-g-HBPAE hyperbrandched/comb-like composite polymer electrolytes (CPEs). The dispersion of nanoparticles in matrix was observed by SEM. The effects of different lithium salts on the properties of CPEs were studied by DSC, tensile test and dielectric spectra. The results showed that the hypergrafting method improved the interphase compatibility between SiO₂ and matrix. Sulfonic acid type lithium salts accelerated self-plasticizing with …

The Study Of Dynamical Electrochemical Impedance Spectroscopy For Oxygen Reduction Reaction On Pt/C Catalyst, Kun-Ming Shi, Jian-Wei Guo, Jia Wang

Journal of Electrochemistry

With joint techniques of rotating disc electrode(RDE) and electrochemical impedance spectroscopy(EIS), and further establishment on equivalent circuit model, this paper studied oxygen reduction reaction(ORR) on commercial Pt/C catalyst in acid medium. Our results found that the dynamical interface on Pt/C consists of two independent processes: 1) the PtO reduction from Pt surface, 2) the new PtO formation from ORR, thus providing key clues for catalyst stability and activity. This also implied that the dynamical interface facilitates reconstruction for porous electrode, and matches with mass transfer. One important issue is discovered that at high overpotential, the high reaction rate for ORR …

Research Progress Of Si-Based Anode Materials For Lithium-Ion Batteries, Ding-Qiong Chen, Yang Yang, Qiu-Li Li, Jin-Bao Zhao

Journal of Electrochemistry

Owing to its high theoretical specific capacity (4200 mAh·g^-1), silicon is a promising candidate to replace graphite as the anode in lithium ion batteries (LIBs). However, low intrinsic electric conductivity and dramatic volume change (~ 300%) during the process of lithiation and delithiation result in electrode pulverization and capacity loss with cycling, accordingly, the application of silicon as an anode in LIBs has been severely hindered. We will discuss the structure of silicon electrode including synthesis of Si-based composites,the selection of binder for silicon and the fabrication of binder-free Si-based electrode, as well as the electrolyte additive to …

Research And Application Of Key Materials For Sodium-Ion Batteries, Yong-Chang Liu, Cheng-Cheng Chen, Ning Zhang, Liu-Bin Wang, Xing-De Xiang, Jun Chen

Journal of Electrochemistry

Sodium-ion batteries (SIBs) have been considered as a potential large-scale energy storage technology owing to the abundance, wide distribution, and low price of sodium resources. However, the larger and heavier sodium ion as compared to lithium ion makes it difficult to identify appropriate electrode materials with the capability for fast and stable sodium-ion insertion/extraction. Furthermore, the optimization of electrolyte, the matching of cathode and anode materials, and the construction of sodium-ion full batteries with high-performance, high-safety, and low-cost are urgently needed in order to make SIBs commercially available. This review summarizes the up-to-date research progresses in key materials (including cathode, …

Micro/Nano-Structured Electrode Materials For Sodium-Ion Batteries, Shuang Yuan, Yun-Hai Zhu, Sai Wang, Tao Sun, Xin-Bo Zhang, Qiang Wang

Journal of Electrochemistry

Sodium has similar physics and chemical properties to lithium, alternatively, sodium (Na)-ion batteries have again aroused a great deal of interest recently, particularly for large-scale stationary energy storage applications due to the practically infinite sodium resources and low cost. However, the technics and materials for Na-ion batteries are immature. Therefore, development of advanced anode and cathode materials for Na-ion batteries is urgently desired but remains a great challenge. This paper briefly reviews some recent progresses in this field, addressing the morphology effects, as well as functions of carbon composite materials toward Na-ion batteries. Several electrode materials with micro/nano-structures based on …

Continuous Synthesis And Condition Exploration Of Precursor Ni1/3Co1/3Mn1/3(Oh)2 Ternary Cathode Material, Zhi-Jun Jiang, Ya-Li Zhang, Qian Wang, Hui Zhang

Journal of Electrochemistry

Commercial LiNi_1/3Co_1/3Mn_1/3(OH)₂ ternary material is generally prepared by a combination of co-precipitation and solid state reaction method. The particle size distribution and morphology of Ni_1/3Co_1/3Mn_1/3(OH)₂ precursor have a great impact on the electrochemical performance of LiNi_1/3Co_1/3Mn_1/3O₂. In this work, the precursor Ni_1/3Co_1/3Mn_1/3(OH)₂ ternary cathode material was prepared by co-precipitation method with MnSO₄, NiSO₄, and CoSO₄ as raw materials, NaOH as a precipitating agent and NH_{3 …}

Template-Assisted Hydrothermal Synthesis Of Nio@Co3O4 Hollow Spheres With Hierarchical Porous Surfaces For Supercapacitor Applications, Wen Zhou, Xue-Feng Lu, Ming-Mei Wu, Gao-Ren Li

Journal of Electrochemistry

Hollow structures have shown great potentials in a variety of important applications, such as energy conversion and storage. In order to further enhance the performance, the rational design of hollow structures with higher complexity in terms of composition and structure is highly desirable and still remains a great challenge. In this work, an efficient strategy was established for the fabrication of novel NiO@Co₃O₄ hollow spheres (HSs) with hierarchical porous surfaces by silica spheres template-assisted hydrothermal synthesis. The as-fabricated NiO@Co₃O₄ HSs showed high specific surface area of 219.68 m²·g^-1, and significant …

Electrochemical Performance Of Crystalline Li12Si7 As Anode Material For Lithium Ion Battery, Ya-Xiong Yang, Rui-Jun Ma, Ming-Xia Gao, Hong-Ge Pan, Yong-Feng Liu

Journal of Electrochemistry

Crystalline Li₁₂Si₇ is successfully synthesized by heating the mixture of LiH and Si with a molar ratio of 12:7, which avoids the huge difference of the melting points between Li and Si. The electrochemical performance and lithium storage mechanism of the as-prepared Li12Si7 are studied in this work. It is found that only a change in cell volume takes place without a phase change during the lithiation/delithiation of Li₁₂Si₇ at a voltage range of 0.02 ~ 0.6 V, exhibiting a solid-solution lithium storage mechanism. Such a lithium storage process effectively retards the volume effect …

Enhanced Metallic Properties Of Srruo3 Thin Films Via Kinetically Controlled Pulsed Laser Epitaxy, Justin K. Thompson, J. Nichols, S. Lee, S. Ryee, John H. Gruenewald, John G. Connell, Maryam Souri, J. M. Johnson, J. Hwang, M. J. Han, H. N. Lee, D. -W. Kim, Sung S. Ambrose Seo

Physics and Astronomy Faculty Publications

Metal electrodes are a universal element of all electronic devices. Conducting SrRuO₃ (SRO) epitaxial thin films have been extensively used as electrodes in complex-oxide heterostructures due to good lattice mismatches with perovskite substrates. However, when compared to SRO single crystals, SRO thin films have shown reduced conductivity and Curie temperatures (T_C), which can lead to higher Joule heating and energy loss in the devices. Here, we report that high-quality SRO thin films can be synthesized by controlling the plume dynamics and growth rate of pulsed laser epitaxy (PLE) with real-time optical spectroscopic monitoring. The SRO thin …

Effect Of Preparation Technology On Arc Erosion Resistance Of Mgo/Cu Contact Materials, Xiuhua Guo, Kexing Song, Yanmin Zhang, Xuebin Zhang, Jianxin Gao

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Thermodynamic Calculation Of The Liquidus Surface Projection Of Multi-Component Aluminum Alloys, Jingrui Zhao, Yong Du, Lijun Zhang, Jixue Zhou, Yuansheng Yang

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

A356 Aluminum Alloy, Grain Refining, Modification, Microstructure, Mechanical Properties, Jonghun Yoon

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

A Molecular Dynamics Study Of Activated Tungsten Inert Gas Welding Process, Cheng Jin, Hanchen Huang

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Effect Of Thickness Of Anode Functional Layer On Electrochemical Performance Of Ni-Ce0.8gd0.2o1.9 Anode-Supported Solid Oxide Fuel Cells, Xueping Guo, Kaiping Peng, Chan Zheng, Wei Li, Wenzhe Chen

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Study On Impact And Friction Properties Of Za45si3cu Alloy, Weihe Shi

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Modelling The Evaporation Of Aluminum In Ti–6al–4v Alloy Melted With Electron Beam And Laser, Xuan Wang, Liang Wang, Liang S. Luo, Yan Q. Su, Xin Z. Li, Rui R. Chen, Jing J. Guo, Heng Z. Fu

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Study On Criterion Of Fabricating Columnar Dendrite Structure Dz466 Superalloy Based On Lmc Process, Xun Sun

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Experimental Investigation On Recovery Of Fe-Ni Alloy From Bayer Red Mud And Laterite Nickel, Aoping He, Chen Liu, Jianmin Zeng

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Microstructures And Properties Of Sintered Cu–Mos2/Cu Functional Gradient Materials, Aiqin Wang

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

(Alpha + Gamma) Ultrafine Duplex Structure Formation In Twophase Stainless Steel By High-Pressure Torsion And Annealing, Mie Ota, Kei Ameyama, Daiki Nanya, Sanjay Kumar Vajpai

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Study On The Impact Abrasive Wear Of New Super-High Manganese Steel, Wenyan Wang

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Simulation Of Superplastic Forming Of Circular Edge-Welded Envelopes, Olga Tulupova

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Constitutive Equation Of Compression For 38mnv Micro-Alloyed Steel, Jun Hu, Jianmin Zeng

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Numerical Modeling And Seismic Assessment Of Smart Isolation System For High-Speed Railway Rc Bridge Subjected To Near-Field Ground Motions, Lingkun Chen

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Modelling The Softening Behaviour During Galvanizing Of Various Steel Grades, Kevin Banks, Rorisang Maubane, Thabang Makwena

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.