Materials Science and Engineering Commons^™

Effect Of Class C And Class F Fly Ash On Early-Age And Mature-Age Properties Of Calcium Sulfoaluminate Cement Paste, Sukanta K. Mondal, Carrie Clinton, Hongyan Ma, Aditya Kumar, Monday Uchenna Okoronkwo

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

To Promote the Sustainable Development of Eco-Efficient Calcium Sulfoaluminate (CSA) Cements through the Partial Replacement of the CSA Clinker with Supplementary Cementitious Waste Products, the Effects of Coal Fly Ashes on the Early-Age and Mature-Age Properties of a Calcium Sulfoaluminate (CSA)-Based Cement Paste Were Investigated. the Impacts of Both Class C and Class F Fly Ashes on the Rheological Properties, Hydration Kinetics, and Compressive Strength Development of CSA Cement Paste Were Studied. Rheology-Based Workability Parameters, Representing the Rate of Loss of Flowability, the Rate of Hardening, and the Placement Limit, Were Characterized for the Pastes Prepared with Fixed Water-To-Cement (W/c) …

Polyethersulfone Thin-Film Nanocomposite Membrane Embedded With Amine-Functionalized Graphene Oxide For Desalination Applications, Ahmed Bahaeldin

Theses and Dissertations

Thin-film nanocomposite (TFN) desalination membranes were prepared based on a polyethersulfone (PES) support, where the polyamide (PA) layer was embedded with amine-functionalized graphene oxide (GO). The effect of adding various concentrations of functionalized and un-functionalized GO on the desalination performance, hydrophilicity, and morphology of the membranes was additionally assessed throughout this work. Scanning electron microscopy (SEM) measurements were used to assess the morphology of the membranes in combination with Brunauer-Emmett-Teller (BET) analysis. Contact angle measurements were used to gauge the hydrophilicity of the synthesized membranes. The membrane with the best desalination performance contained 1x10^-3 wt/vol% of functionalized GO in …

Preface To Special Issue: Electrocatalysis And Electrosynthesis, Fang-Yi Cheng, Shuang-Yin Wang, Tian-Hua Zhou

Journal of Electrochemistry

No abstract provided.

Recent Advances In Exploring Highly Active & Durable Pgm-Free Oxygen Reduction Catalysts, Yuan Li, Miao-Ying Chen, Bang-An Lu, Jia-Nan Zhang

Journal of Electrochemistry

In order to reduce the considerable usage of expensive but scarce platinum at the cathode in proton exchange membrane fuel cells (PEMFCs), it is necessary to pursue alternatives to platinum. The most promising platinum group metal (PGM)-free catalysts for oxygen reduction reaction (ORR) are atomically dispersed, and nitrogen-coordinated metal site catalysts denoted as M-N-C (M = Fe, Co, or Mn, etc.). Over the last few decades, there have been great advances in these catalysts with high ORR activity and promising initial fuel cell performance approaching traditional Pt/C catalysts. However, the stability of these highly active Fe-N-C catalysts under practical fuel …

Electrochemical Oxidation Of Ethylene On Palladium Electrode, Wei-Xing Wu, Ying Wang

Journal of Electrochemistry

The electrochemical oxidation of C₂H₄ is attracting increasing attention due to its vast potential market. The current electrochemical methods rely on the use of redox mediators, which may produce corrosive intermediates, while direct oxidation is still limited by its low activity and selectivity. Herein, we conducted electrochemical studies to obtain mechanistic insights into the benchmark Pd catalyst. The generated Pd(II) could be the active site for C₂H₄ oxidation. By designing the pulse sequence, we found the ratio of strongly and weakly adsorbed C₂H₄ on Pd to be 0.3:1. The result we …

Supperlattice-Like Structure: Ordered Mass Transfer Endowing High Quality Output Of Fuel Cell, Jian Wang, Wen-Hui Xuan, Qian He, Jing-Xia Jiang, Yuan-Yuan Zhou, Yao Nie, Qiang Liao, Min-Hua Shao, Wei Ding, Zi-Dong Wei

Journal of Electrochemistry

The current or voltage fluctuation in fuel cell operation is harmful to the fuel cell system and power application equipment. Here, we report a technique to eliminate such a fluctuation by the aid of new type of catalysts, superlattice-like mesoporous PtCo catalysts. The current fluctuation in fuel cells catalyzed by two invented catalysts are fixed at as low as 25 mA·cm⁻² with a power of 0.75 W·cm⁻² or 120 mA·cm⁻² with a power of 1.01 W·cm⁻², and no noticeable current decay was detected over 100 h. By contrast, a …

Non-Equilibrium Colloidal Phenomena In Magnetic Fields And Photoillumination: From Controlling Living Microbots To Understanding Microplastics, Ahmed Al Harraq

LSU Doctoral Dissertations

Colloids are a ubiquitous class of materials composed of microscopic particles suspended in a continuous phase which are found in everyday products and in nature. Colloids are also useful models for studying the spontaneous arrangement of matter from individual building blocks to mesophases. Standard treatment of colloid science is based on the assumption of equilibrium conditions, as defined in traditional thermodynamics. However, novel assembly mechanisms and motility are unlocked by pushing colloids away from equilibrium using external energy. In addition, many colloids in nature and in industrial applications exchange energy and mass with the surrounding environment thus behaving in a …

Methods For Determining The Infrared Complex Refractive Indices N(Λ) And K(Λ) From Organic Solid Powders: Comparison Of A Sucrose Single Crystal And A Pressed Pellet, Michael O. Yokosuk, Danielle L. Saunders, Charles Tom Resch, Jeremy D. Erickson, Charmayne E. Lonergan, Sarah D. Burton, Mark E. Bowden, Kelly A. Peterson, Timothy J. Johnson, Tanya L. Myers

Materials Science and Engineering Faculty Research & Creative Works

There exists a need to measure optical constants n and k for many materials, especially organic solids in the infrared spectral region, but at present, there are only two established methods for making such measurements: single-angle (SA) reflectance and infrared spectroscopic ellipsometry (IRSE). the former derives the n/k vectors via measurement of the change in the amplitude of light reflected from the sample and then uses the Kramers-Kronig transform, while the latter measures the change in polarization of the reflected light from the sample to derive n/k. Here we make a direct comparison between the n/k vectors derived from SA …

Probing Dna Structural Heterogeneity By Identifying Conformational Subensembles Of A Bicovalently Bound Cyanine Dye, Matthew S. Barclay, Azhad U. Chowdhury, Austin Biaggne, Jonathan S. Huff, Nicholas D. Wright, Paul H. Davis, Lan Li, William B. Knowlton, Bernard Yurke, Ryan D. Pensack, Daniel B. Turner

Materials Science and Engineering Faculty Publications and Presentations

DNA is a re-configurable, biological information-storage unit, and much remains to be learned about its heterogeneous structural dynamics. For example, while it is known that molecular dyes templated onto DNA exhibit increased photostability, the mechanism by which the structural dynamics of DNA affect the dye photophysics remains unknown. Here, we use femtosecond, two-dimensional electronic spectroscopy measurements of a cyanine dye, Cy5, to probe local conformations in samples of single-stranded DNA (ssDNA–Cy5), double-stranded DNA (dsDNA–Cy5), and Holliday junction DNA (HJ–DNA–Cy5). A line shape analysis of the 2D spectra reveals a strong excitation–emission correlation present in only the dsDNA–Cy5 complex, which is …

Adsorptive Properties And On-Demand Magnetic Response Of Lignin@Fe3o4 Nanoparticles At Castor Oil–Water Interfaces, Mohammad J. Hasan, Emily Westphal, Peng Chen, Abishek Saini, I-Wei Chu, Sarah J. Watzman, Esteban E. Ureña-Benavides, Erick S. Vasquez

Chemical and Materials Engineering Faculty Publications

Lignin@Fe3O4 nanoparticles adsorb at oil–water interfaces, form Pickering emulsions, induce on-demand magnetic responses to break emulsions, and can sequester oil from water. Lignin@Fe3O4 nanoparticles were prepared using a pH-induced precipitation method and were fully characterized. These were used to prepare Pickering emulsions with castor oil/Sudan red G dye and water at various oil/water volume ratios and nanoparticle concentrations. The stability and demulsification of the emulsions under different magnetic fields generated with permanent magnets (0–540 mT) were investigated using microscopy images and by visual inspection over time. The results showed that the Pickering emulsions were more stable at the castor oil/water …

Artificial Intelligence Assisted Residual Strength And Life Prediction Of Fiber Reinforced Polymer Composites, Partha Pratim Das, Muthu Ram Prabhu Elenchezhian, Vamsee Vadlamudi, Rassel Raihan

Institute of Predictive Performance Methodologies (IPPM-UTARI)-Archive

With the increased use of composite materials, researchers have developed many approaches for structural and prognostic health monitoring. Broadband Dielectric Spectroscopy (BbDS)/Impedance Spectroscopy (IS) is a state-of-the-art technology that can be used to identify and monitor the minute changes in damage initiation, accumulation, interactions, and the degree of damage in a composite under static and dynamic loading. This work presents a novel artificial neural network (ANN) framework for fiber-reinforced polymer (FRP) composites under fatigue loading, which incorporates dielectric state variables to predict the life (durability) and residual strength (damage tolerance) from real-time acquired dielectric permittivity of the material. The findings …

The Effect Of Graphite And Activated Carbon As Dispersed Particle In Base Fluid As Quench Medium On The Hardness Of S45c Carbon Steel, Wahyuaji Narottama Putra, Danika Aprilia Somadinata, Ghiska Ramahdita

Journal of Materials Exploration and Findings

Adding a solid particle dispersion into a base fluid could increase its thermal conductivity, hence increasing the heat transfer characteristics. One example of this thermally enhanced fluid is in heat treatment industry as quench medium. By controlling the amount of the dispersed particle, the cooling rate of the quench medium can be altered, and could affect steel hardness after heat treatment. In this research, the dispersed particle used was commercially available graphite and activated carbon particle. As for the base fluid, distilled water and common engine oil were compared. The concentration of the dispersed particle was 0.1, 0.3, 0.5 weight …

Freespan Analysis For Subsea Pipeline Integrity Management Strategy, Nurul Hadi, Muhammad Helmi, Edo Cathaputra, Dedi Priadi, Donanta Dhaneswara

Journal of Materials Exploration and Findings

Abstract. Over a rough seabed or on seabed subject to scour, freespans can occur when contact between a subsea pipeline and the seabed is lost over an acceptable distance. When this exceeds the allowable freespan length, design stresses can be exceeded, and a vortex induced vibration (VIV) response can be initiated, resulting in the risk of fatigue failure. If this is not predicted and controlled properly, it will affect pipeline integrity, leading to expensive rectification and intervention work. Freespan analysis consisted primarily of a screening check in which the as-found freespans from Remotely Operated Vehicle (ROV) or multibeam Side …

Structural Integrity Analysis Of The Rig Mast Following Repair Of Two Diagonal Braces In The Upper Mast Section, Rendhatya Padmodwiputra, Johny Wahyuadi Soedarsono, Mirza Mahendra, Bambang Eka Satria, Chandra Arif, Eka Juni Suarthana

Journal of Materials Exploration and Findings

During a move to the new drilling location, two braces of the upper mast section on a 550 HP oil and gas rig was damaged. When damage is discovered, the rig operating company should conduct a risk analysis related to the damage using the standard used to determine rejection criteria and follow-up repairs. The strength of the rig mast is calculated using Finite Element Analysis (FEA) with initial conditions (before damage occurs) where all braces are installed and extreme conditions where neither brace is repaired. The calculation results are then used to assess the risk of reducing the rig mast …

Development Of Battery Materials To Function As Corrosion Protection On Car Body Plates, Tubagus Noor Rohmannudin, Sulistijono Sulistijono, Noval Adrinanda, Faridz Wira Dharma, Samuel Areliano

Journal of Materials Exploration and Findings

Most car bodies made for mass production are made from steel or aluminum. Both are strong metals, but steel is cheaper than aluminum and is more commonly used in lower-end cars for a broader consumer range. The weakness of steel compared to aluminum is that it is susceptible to corrosion under certain conditions, and thus it may deteriorate over time without proper care. To prevent corrosion, modern cars are coated with paint to prevent direct contact with the environment. As a second line of protection, a car battery can be connected to the body to create an impressed current cathodic …

Effect Of Austenization And Repeated Quenching On The Microstructures And Mechanical Properties Of Wear-Resistant Steel, Yanuar Nugraha, Myrna Ariati Mochtar

Journal of Materials Exploration and Findings

This study was focused on determining the effect of repeated austenitization and quenching on mechanical properties and microstructure. The experiment was carried out in a rolled quencher facility with a heat treatment process of one to two times, with parameters of an austenizing temperature of 9500C and quenching at a temperature of 8500C with pressurized water media. Testing of specimens, including microstructure observations and hardness testing. The repeated heat treatment process showed an increase in hardness of 0.79% on one-time repeated heat treatment and 1.65% on two repeated heat treatments. This occurs due to the presence accompanied by refinement of …

Potential Of Biduri Fiber (Calotropis Gigantea) As Material For Oil Spill Absorbent, Anne Sukmawati, Wulan Septiani

Journal of Materials Exploration and Findings

Biduri fiber (Calotropis gigantea) is a natural hollow fiber with hydrophobic and oleophilic properties potentially used as oil spilled sorbent from seawater. This study aims to determine the absorption capacity and efficiency of the Biduri fiber and membrane to fuel oil. Measurement of oil absorption to seawater was carried out at various fiber weights (0.5-1.5 g), fiber composition (50-95%), contact time (10-90 minutes), temperature (30 and 50°C), and compared with commercial products. The results showed that the fiber weight variation of 0.5-1.5 g has an average absorption efficiency of 96.67%, and the highest absorption was obtained in a weight of …

The Effects Of Phosphorus Pentoxide Additions On The Thermal, Rheological, And Structural Properties Of Sodium Borosilicate Glass, K. L. Skerratt-Love, J. L. George, A. M.T. Bell, F. Sweeney, D. Cutforth, C. (Charmayne) E. Lonergan, D. R. Dixon, A. A. Kruger, P. A. Bingham

Materials Science and Engineering Faculty Research & Creative Works

This research has characterized the effects of P₂O₅ additions on the physical, chemical, thermal, rheological properties and the structure of SiO₂-B₂O₃-Na₂O glasses relevant to radioactive waste immobilization. Properties analyzed include high-temperature viscosity, glass transition temperature (T_g) and structure. X-ray diffraction (XRD) confirmed a solubility limit of between 3.0 and 4.0 mol% P₂O₅ for the onset of crystallinity with formation of Na₃PO₄ and Na₄P₂O₇ in annealed bulk glasses; and between 4.0 and 5.0 mol% P₂O …

Network Structures And The Properties Of Na-Ca-Sr-Borophosphate Glasses, Parker T. Freudenberger, Rebekah L. Blatt, Randall E. Youngman, Richard K. Brow

Materials Science and Engineering Faculty Research & Creative Works

Borophosphate glasses were prepared with the nominal molar compositions 16Na2O-(24-y)CaO-ySrO-xB2O3-(60-x)P2O5 (mol%), where 0≤x≤60 and y=0, 12, and 24. Information about the compositional dependence of borate and phosphate site speciation and next nearest neighbor linkages was obtained by 11B and 31P MAS NMR and Raman spectroscopies, and by high pressure liquid chromatography (HPLC). With the initial replacement of P2O5 by B2O3, tetrahedral borate sites linked to four phosphate anions, B(ØP)4, are created in the glass structure, and the average phosphate anion becomes smaller as bridging PØP bonds are replaced by bridging PØB bonds. With further increases in the B2O3 content, borate …

Network Structures And The Properties Of Na-Ca-Sr-Borophosphate Glasses, Parker T. Freudenberger, Rebekah L. Blatt, Randall E. Youngman, Richard K. Brow

Materials Science and Engineering Faculty Research & Creative Works

Borophosphate glasses were prepared with the nominal molar compositions 16Na₂O-(24-y)CaO-ySrO-xB₂O₃-(60-x)P₂O₅ (mol%), where 0≤x≤60 and y=0, 12, and 24. Information about the compositional dependence of borate and phosphate site speciation and next nearest neighbor linkages was obtained by ¹¹B and ³¹P MAS NMR and Raman spectroscopies, and by high pressure liquid chromatography (HPLC). With the initial replacement of P₂O₅ by B₂O₃, tetrahedral borate sites linked to four phosphate anions, B(ØP)₄, are created in the glass structure, and the average phosphate anion …

Network Structures And The Properties Of Na-Ca-Sr-Borophosphate Glasses, Parker T. Freudenberger, Rebekah L. Blatt, Randall E. Youngman, Richard K. Brow

Mathematics and Statistics Faculty Research & Creative Works

Borophosphate glasses were prepared with the nominal molar compositions 16Na2O-(24-y)CaO-ySrO-xB2O3-(60-x)P2O5 (mol%), where 0≤x≤60 and y=0, 12, and 24. Information about the compositional dependence of borate and phosphate site speciation and next nearest neighbor linkages was obtained by 11B and 31P MAS NMR and Raman spectroscopies, and by high pressure liquid chromatography (HPLC). With the initial replacement of P2O5 by B2O3, tetrahedral borate sites linked to four phosphate anions, B(ØP)4, are created in the glass structure, and the average phosphate anion becomes smaller as bridging PØP bonds are replaced by bridging PØB bonds. With further increases in the B2O3 content, borate …

Temperature, Pressure, And Adsorption Dependent Redox Potentials: Iii. Processes Of Co Conversion To Value-Added Compounds, Siyuan Fang, Yun Hang Hu

Michigan Tech Publications, Part 1

Carbon monoxide (CO) is a primary air pollutant and a poisonous species for human beings, animals, and some catalytic reactions. Meanwhile, CO is also a versatile feedstock in the chemical industry to produce high‐value chemicals and clean fuels, which has stimulated extensive research interests in exploiting efficient CO conversion processes. Redox potential is a key thermodynamic quantity in these processes whereas only standard reduction potentials at 25°Cand 1 atm are currently available. Herein, it is the first time to report the effects of temperature (0–1000°C), pressure (1–100 atm), and adsorption on the redox potentials of 18 CO conversion reactions to …

Liquid-Liquid Equilibria Of Water + Ethanol + Castor Oil And The Effect Of Cellulose Nanocrystal/Fe3o4 And Lignin/Fe3o4 Nanoparticles, Mohammad J. Hasan, Fariba Yehaneh, Amy Ciric, Peng Chen, Erick S. Vasquez, Esteban E. Ureña-Benavides

Chemical and Materials Engineering Faculty Publications

Castor oil has been proposed as a renewable solvent for the liquid extraction of ethanol from water as an alternative to more traditional energy intensive distillation-based methods. The liquid–liquid equilibrium (LLE) of the ternary system water + ethanol + castor oil was determined at 295.15 K using high performance liquid chromatography (HPLC). Castor oil was herein treated as a pseudo-component with the molecular weight of the triglyceride of ricinoleic acid. The experimental data was fitted to the UNIQUAC and NRTL models to obtain parameters for castor oil, and binary interaction parameters for castor oil/ethanol and castor oil/water pairs. The separation …

Architecture Of Heptagonal Metallo-Macrocycles Via Embedding Metal Nodes Into Its Rigid Backbone, A.M.Shashika D. Wijerathna, He Zhao, Qiangqiang Dong, Qixia Bai, Zhiyuan Jiang, Jie Yuan, Jun Wang, Mingzhao Chen, Markus Zirnheld, Rockwell T. Li, Yuan Zhang, Yiming Li, Pingshan Wang

College of Sciences Posters

Metal-organic macrocycles have received increasing attention not only due to their versatile applications such as molecular recognition, compounds encapsulation, anti-bacteria and others, but also for their important role in the study of structure-property relationship at nano scale. However, most of the constructions utilize benzene ring as the backbone, which restricts the ligand arm angle in the range of 60, 120 and 180 degrees. Thus, the topologies of most metallo-macrocycles are limited as triangles and hexagons, and explorations of using other backbones with large angles and the construction of metallo-macrocycles with more than six edges are very rare.

In this study, …

Advanced Microstructural Characterization Of Functionally Graded Dental Ceramic Material For Materials-Informed Finishing, Angani Vigneswaran

Theses and Dissertations--Manufacturing Systems Engineering

Yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) has gained popularity as the choice of material for dental prosthetics. Ivoclar Vivadent’s IPS e.max ZirCAD Prime dental ceramic incorporates a unique gradient technology that varies the yttria content over the thickness of the material. The top layer is composed of 5Y-TZP which is desired for its optical properties while the bottom layer is composed of a much stronger 3Y-TZP. In between the two layers, 5Y-TZP and 3Y-TZP are mixed to form a transition layer. Varying the amount of yttria allows for more esthetically pleasing translucency in the visible areas of the restoration without compromising …

Achieving Strong Chemical Interface And Superior Energy-Saving Capability At The Crosslinks Of Rubber Composites Containing Graphene Oxide Using Thiol-Vinyl Click Chemistry, Rui Zhang, Jiaye Li, Zongchao Xu, Stephen Jerrams, Shui Hu, Li Lui, Shipeng Wen, Liqun Zhang

Articles

Rapidly developments in international transportation inevitably lead to an increase in the consumption of energy and resources. Minimizing the rolling resistance of tires in this scenario is a pressing challenge. To lower the rolling resistance of tires, enhancing the interaction between fillers and rubber molecules while improving the dispersion of fillers are required to reduce the internal mutual friction and viscous loss of rubber composites. In this study, graphene oxide (GO) was modified using γ-mercaptopropyltrimethoxysilane (MPTMS) with thiol groups. A modified GO/natural rubber (MGO/NR) masterbatch with a fine dispersion of MGO was then introduced into solution-polymerized styrene butadiene rubber (SSBR) …

A Partial Discharge Inception Voltage Modeling Approach, Shilpi Mukherjee, Tristan Mark Evans, David Huitink, H. Alan Mantooth

Electrical Engineering Faculty Publications and Presentations

A partial discharge inception voltage modeling approach promoting design-for-reliability considerations in advanced power modules is presented. As power modules are being operated at higher voltages and become more compact to meet power density demands, there is an increased risk of partial discharge, the silent precursor to electrical breakdown that degrades insulation material. The trade-off between voltage class and module compaction must be quantified. This work presents a methodology to model the tradeoff for any substrate and encapsulant material. A surface charge density-based partial discharge inception voltage (PDIV) model was developed to overcome the challenges in electric field-based models. The model …

Development Of High Current Electromigration Test System For Evaluation Of Novel Solder Structures, Nicholas Pareis

Electronic Theses and Dissertations, 2020-2023

Electromigration reliability of ball-grid-array (BGA) solder joints is emerging as a critical area of research for advanced microelectronic devices, especially those with high power requirements. In this study, a novel high current electromigration test system, including a temperature sensing capability, was designed and developed for the purpose of performing electromigration characterization of various BGA solder joint structures, including features designed for reduced current crowding. This study consisted of two main parts: design and development of a novel high current electromigration test system, and using this novel system for electromigration characterization of BGA solder joints. In the first portion of this …

Xps Study Of Calcium Lanthanum Sulfide Ceramics, Brian E. Butkus

Graduate Thesis and Dissertation 2023-2024

Long wave infrared (LWIR) optics that transmit in the 8 to 14 m wavelength range and, additionally, can withstand severe physical and thermal stresses are needed for advanced remote sensing, guidance and communication-based applications. However, most non-oxide transparent LWIR optics do not have the wider transmission range, nor the hardness and resistance to thermal shock needed for extreme environments. Because of these limitations, research is circling back to a promising material, calcium lanthanum sulfide (CLS), that could meet LWIR needs for extreme environments.

In this thesis, we will demonstrate the abilities of x-ray photoelectron spectroscopy (XPS) as a technique for …

Functionalization Of 1d And 2d Nanostructures And Their Applications, Yuen Yee Li Sip

Graduate Thesis and Dissertation 2023-2024

Material discovery and development has been playing a significant role in shaping human civilizations, by studying and improving materials for appealing observations to aid in our survival as well as to satisfy our curiosity. From the common earthly materials that give us strong building structures and hunting weapons to the Silicon Age that contributes to the creation of modern electronics and computers, the development of novel and enhanced materials continues to grow. Recently, a new field has emerged that is rapidly expanding the engineering circle; these are called nanomaterials. By shrinking bulk materials into structures with nanoscale dimensions, there is …