Materials Science and Engineering Commons^™

Effect Of Addition Titanium Dioxide Nanoparticle On Properties Of Pineapple Leaf Fiber Mediated Tempo Oxidation, Rahmad Ikrom Ramadhan, Heru Suryanto, Ahmad Atif Fikri, Aminnudin Aminnudin, Jibril Maulana, Faqih Fadillah, Mohamed T. Mito, Kemal Masera

Journal of Mechanical Engineering Science and Technology (JMEST)

Indonesia is an agricultural country with the potential to grow many plants as natural fiber sources. In order to improve its properties, natural fiber needs to be treated by applying nanomaterial so that it can compete with the characteristics of synthetic fibers. The study aims to determine the influence of adding titanium dioxide (TiO2) nanoparticles on pineapple leaf fiber (PALF) characteristics. The PALF was collected from the Subang plantation (Indonesia). The chemical treatment was carried out with pre-treatment using an alkalization process for 3 hours, and the oxidation process was carried out with TEMPO. TiO2 nanoparticle grafting was carried out …

Computational Fluid Dynamics Analysis Of Temperature Distribution In Solar Distillation Panel With Various Flat Plate Materials, Trismawati Trismawati, Hendry Y. Nanlohy, Helen Riupassa, Susi Marianingsih

Journal of Mechanical Engineering Science and Technology (JMEST)

As the world population continues to grow, the demand for clean water is increasing daily, making it a crucial resource to access. However, there are ways to harness abundant resources like solar energy and seawater to produce clean water. The present studies have conducted experimental investigations to convert seawater into freshwater using solar stills, where solar energy is utilized as the primary heat source for evaporation. The temperature distribution inside the solar stills was analyzed using a flat plate made of three different materials: copper, stainless steel, and aluminum. To examine the temperature distribution and performance of the solar stills, …

Comparative Analysis Of The Effect Dual Spark Ignition And Single Spark Ignition On Performance And Exhaust Emissions In Bioethanol-Fueled Engines, Avita Ayu Permanasari, Ahmad Faizal Wahidin, Hasan Ismail, Erwin Komara, Poppy Puspitasari, Gina A. Lorenzo

Journal of Mechanical Engineering Science and Technology (JMEST)

Bioethanol is an alternative fuel that has a high octane value of around 100 to 110, making it difficult to be applied to spark ignition engines directly. So, it is necessary to make adjustments, including increasing combustion efficiency and thermal efficiency of the combustion chamber by increasing the compression ratio and adjusting the ignition system, both in single spark ignition (SSI) and dual spark ignition (DSI) types. The study aims to determine the effect of SSI and DSI applications on engine performance, specific fuel consumption (SFC), and exhaust emissions using 96% and 99% levels of bioethanol fuel. The results showed …

Performance Enhancement Of Dye Sensitized Solar Cell (Dssc) Through Tio2/Rgo Hybrid: Comprehensive Study On Synthesis And Characterization, Rustan Hatib, Khairil Anwar, Ramang Magga, Muh Anjas Astak, Denny Widhiyanuriyawan, Wardoyo Wardoyo

Journal of Mechanical Engineering Science and Technology (JMEST)

The TiO2 film is immersed in a graphite oxide solution, preparing it for thermal reduction, which converts the graphite oxide to reduced graphene oxide (rGO). This process produces rGO hybrid TiO2 photoanodes for dye-sensitized solar cells (DSSC). rGO in the TiO2 structure prevents electron recombination and improves overall efficiency. The main advantage of this method is its ability to prevent loss of rGO during the sintering process, which is a common problem with other methods. The study investigated heating temperatures ranging between 300˚C, 350˚C, 400˚C, 450˚C, and 500˚C to determine optimal conditions. The presence of rGO in the photoanode structure …

Pyrolysis Kinetics Of Spirulina Platensis And Non-Condensable Gas Product Distribution In A Fixed-Bed Reactor, Ahmad Yusril Aminullah, Sukarni Sukarni, Retno Wulandari, Muhammad Shahbaz

Journal of Mechanical Engineering Science and Technology (JMEST)

Energy is a fundamental factor for civilization development and sustainability. However, energy sources are dominated by non-renewable fractions, such as fossil fuels. Renewable biomass is projected to be a future fuel source. Spirulina platensis (SP) has numerous advantages compared to other biomass, and it is considered 3rd generation biomass that does not interfere with food and land usage and has a relatively low main decomposition temperature at 325.7℃. Thermogravimetric analysis (TGA) was conducted to observe SP kinetics parameters, especially activation energy. Kissinger-Akahira-Sunose (KAS), Ozawa-Flynn-Wall (OFW), and Starink iso-conversional methods reveal that SP has an activation energy of 152.33, 154.56, and …

Crashworthiness And Deformation Pattern Analysis Of Single And Double Wall With Addition Infill Structure, Redyarsa Dharma Bintara, Moch. Agus Choiron, Yahya Zakariya, M. Hasbi Ash Shiddieqy, Fajar Adi Pratama

Journal of Mechanical Engineering Science and Technology (JMEST)

Ship collisions are a phenomenon that often occurs in maritime transportation. One part of the ship that often experiences damage is the ship's wall (hull). This research aims to analyze and compare deformation patterns, stress distribution, and energy absorption in three wall models, single wall, double wall, and double wall, with the addition of infill structures. The infill structure used Polylactic Acid (PLA) polymer material because it provided convenience in the manufacturing process, while the walls of the test model used Aluminum 6063 material. The test model was developed by carrying out the design process using CAD software. Furthermore, a …

Durability Of Thermoplastic Polyurethane Round Belt Joint With Variations In Heating Methods And Cutting Shapes, Achmad Sabilarrosyad Prawiro Kusumo, Anggit Murdani

Journal of Mechanical Engineering Science and Technology (JMEST)

Thermoplastic polyurethane round belts are widely used for conveyors in various industries, particularly in the food and beverage industry, due to their flexible and abrasion-resistant characteristics. These belts are also popular in manufacturing industries because of their ease of joint. However, a common issue arises when the conveyor belt breaks during the production process. This problem can be attributed to the lack of parameters in the belt joining process at companies. Operators do not have a standard parameter for the joining process. When there is an improper joining operation of an operator, the conveyor belt could fail earlier than the …

Heuristic Approach To Comparing The Environmental Impacts Of Carbon Nanotube Production Methods, Ahmad Atif Fikri, Irham Fadlika, Albarrobi Nabila Saeful, Krisna Dwipa Muhdi, Daniel Febrian Pratama, Nasir Garba Bello

Journal of Mechanical Engineering Science and Technology (JMEST)

Carbon Nanotubes (CNTs) production so far has its own advantages and disadvantages. Some methods that can be used in producing CNTs are chemical vapor deposition (CVD), laser ablation, and arc discharge. The three methods have their own requirements, this causes different environmental impacts on each method. Studies into the environmental impact of the CNTs production process found that during thermal pretreatment of the reactant gas, more than 45 by-products were formed, including methane, volatile organic compounds, and polycyclic aromatic hydrocarbons. Calculating the environmental impact of CNTs production method often has challenges in implementation, because each production process has different systems …

Mechanical Properties Of Corner Lap-45 Types Joined Using Friction Stir Welding, Widia Setiawan, Nugroho Santoso, Felixianus Eko Wismo Winarto, Radhian Krisnaputra, Wirawan Widya Mandala, Jibril Maulana

Journal of Mechanical Engineering Science and Technology (JMEST)

Solid welding has always been concerned with probe design, pins, and joint strength. Many researchers have conducted studies on joints, such as butt joints, lap joints, and T joints, but the results show low strength. This study analyzes the mechanical properties of a new design of a 90o angle joint joined by friction stir welding. This study connected aluminum 6061 using the friction stir welding method using a rectifying jig and a probe with EMS 45 material. The corner joint designs used corner-lap 45 with feed rate as independent variables in 6, 8, 10, 15, and 30 mm/min and dependent …

Fabrication And Characterization Of A Monolithic Photonic Integrated Circuit With High-Aspect Ratio Photonic Device Structures, Sami A. Nazib

Optical Science and Engineering ETDs

The focus of this work was to create a process to fabricate an InP-based Photonic Integrated Circuit (PIC). The design of the PIC required the photonic components of this device to be created by deep etching of an epitaxially-grown multilayer structure. Therefore, a novel dry etching process was developed to produce very high aspect- ratio (HAR) features. This process not only involved the development of dry etch chemistry but also the engineering of a metal mask structure. The next step of the challenge was to use a polymer-based material that would have two functions: cladding for the etched photonic components …

Tension–Compression Fatigue Of A Hybrid Polymer-Matrix/Ceramic-Matrix Composite At Elevated Temperature, Marina B. Ruggles-Wrenn, Joshua Schmidt

Faculty Publications

Fully reversed tension–compression fatigue of a hybrid material comprising polymer matrix composite (PMC) co-cured with a ceramic matrix composite (CMC) was investigated. The PMC portion had a polyimide matrix reinforced with 15 plies of carbon fibers woven in an eight-harness satin weave (8HSW). The CMC portion had three plies of a quartz-fiber 8HSW fabric in a zirconia-based ceramic matrix. The hybrid PMC/CMC was developed for use in aerospace thermal protection systems (TPS). Hence, the experimental setup aimed to simulate the TPS service environment—the CMC side was kept at 329 °C, whereas the PMC side was open to laboratory air. Compression …

Data-Driven Viewpoint For Developing Next-Generation Mg-Ion Solid-State Electrolytes, Fang-Ling Yang, Ryuhei Sato, Eric Jian-Feng Cheng, Kazuaki Kisu, Qian Wang, Xue Jia, Shin-Ichi Orimo, Hao Li

Journal of Electrochemistry

Magnesium (Mg) is a promising alternative to lithium (Li) in solid-state batteries due to its abundance and high theoretical volumetric capacity. However, the sluggish Mg-ion conduction in the lattice of solid-state electrolytes (SSEs) is one of the key challenges that hamper the development of Mg-ion solid-state batteries. Though various Mg-ion SSEs have been reported in recent years, key insights are hard to be derived from a single literature report. Besides, the structure-performance relationships of Mg-ion SSEs need to be further unraveled to provide a more precise design guideline for SSEs. In this Viewpoints article, we analyze the structural characteristics of …

Professor Yong Yang, The Editorial Board Member Of Journal Of Electrochemistry, Is Elected As A Fellow Of The Electrochemical Society, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

Kai Wu, The Editorial Board Member Of Journal Of Electrochemistry And Chief Scientist Of Catl, Receives The National Science And Technology Progress Award, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

Sorbitol-Electrolyte-Additive Based Reversible Zinc Electrochemistry, Qiong Sun, Hai-Hui Du, Tian-Jiang Sun, Dian-Tao Li, Min Cheng, Jing Liang, Hai-Xia Li, Zhan-Liang Tao

Journal of Electrochemistry

The unstable zinc (Zn)/electrolyte interfaces formed by undesired dendrites and parasitic side reactions greatly hinder the development of aqueous zinc ion batteries. Herein, the hydroxy-rich sorbitol was used as an additive to reshape the solvation structure and modulate the interface chemistry. The strong interactions among sorbitol and both water molecules and Zn electrode can reduce the free water activity, optimize the solvation shell of water and Zn²⁺ ions, and regulate the formation of local water (H₂O)-poor environment on the surface of Zn electrode, which effectively inhibit the decomposition of water molecules, and thus, achieve the thermodynamically stable …

Series Reports From Professor Wei’S Group Of Chongqing University: Advancements In Electrochemical Energy Conversions (1/4): Report 1: High-Performance Oxygen Reduction Catalysts For Fuel Cells, Fa-Dong Chen, Zhuo-Yang Xie, Meng-Ting Li, Si-Guo Chen, Wei Ding, Li Li, Jing Li, Zi-Dong Wei

Journal of Electrochemistry

Two major challenges, high cost and short lifespan, have been hindering the commercialization process of low-temperature fuel cells. Professor Wei’s group has been focusing on decreasing cathode Pt loadings without losses of activity and durability, and their research advances in this area over the past three decades are briefly reviewed herein. Regarding the Pt-based catalysts and the low Pt usage, they have firstly tried to clarify the degradation mechanism of Pt/C catalysts, and then demonstrated that the activity and stability could be improved by three strategies: regulating the nanostructures of the active sites, enhancing the effects of support materials, and …

First Announcement Of 76th Annual Meeting Of The International Society Of Electrochemistry, International Society Of Electrochemistry (Ise)

Journal of Electrochemistry

No abstract provided.

Modeling Powder Spreadability In Powder-Based Processes Using The Discrete Element Method, Austin T. Sutton, M. Hossein Sehhat, Ming C. Leu, Joseph W. Newkirk

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Powder-bed fusion (PBF) processes refer to a subset of Additive Manufacturing (AM) techniques where powder is spread on the build-plate before melting (by a laser or electron beam). While PBF processes are attractive due to their ability for realizing complex structures that are either difficult or impossible to create through conventional means, the parts fabricated with these techniques can exhibit defects such as pores, inclusions, and excessive surface roughness. To minimize these defects, much research has been dedicated towards process maturation by optimizing laser or electron beam parameters. However, these developmental efforts typically do not address the recoating process where …

Assessment Of Wafer Scale Mos2 Atomic Layers Grown By Metal–Organic Chemical Vapor Deposition Using Organo-Metal, Organo-Sulfide, And H2S Precursors, Michael Curtis, Olivia Moryan, Nicholas Mckibben, Josh Eixenberger, Chen Chen, Karthik Chinnathambi, Sergej Pasko, Salim El Kazzi, Joan M. Redwing, David Estrada

Materials Science and Engineering Faculty Publications and Presentations

Transition Metal Dichalcogenides (TMDs) are a unique class of materials that exhibit attractive electrical and optical properties which have generated significant interest for applications in microelectronics, optoelectronics, energy storage, and sensing. Considering the potential of these materials to impact such applications, it is crucial to develop a reliable and scalable synthesis process that is compatible with modern industrial manufacturing methods. Metal–organic chemical vapor deposition (MOCVD) offers an ideal solution to produce TMDs, due to its compatibility with large-scale production, precise layer control, and high material purity. Optimization of MOCVD protocols is necessary for effective TMD synthesis and integration into mainstream …

Developing And Testing Low-Cost Air Cleaners For Safer Spaces During Wildfires, Brett W. Stinson, Elliott T. Gall

Mechanical and Materials Engineering Faculty Publications and Presentations

Air cleaning reduces indoor exposure to fine particulate matter (PM2.5) during wildfire smoke events. However, resource and cost constraints may limit access to air cleaning during such an event, as both commercial devices and the higher-rated MERV filters that do-it-yourself (DIY) assemblies typically rely upon tend to be expensive and in short supply. With these constraints in mind, we developed and evaluated several configurations of a novel, DIY air cleaner that uses common household fabrics as filtration media. Clean air delivery rates (CADRs) of the devices were experimentally evaluated in two ways: first, with independent measurements of flowrates and single …

The Role Of Furan Moieties On The Thermal Decomposition And Char Formation Of Intrinsically Fire-Resistant Epoxy Thermosets For Composites, Amy E. Honnig Bassett

Theses and Dissertations

Fire-retardant chemicals added to epoxy thermosets used as coatings, adhesives, and fiber-reinforced polymer composites (FRPCs) negatively impact performance and the environment. This dissertation takes a novel approach to mitigate the flammability of these systems by designing intrinsically fire-resistant epoxies via the incorporation of furan moieties. Glycidyl amines based on furfuryl amine and judiciously selected derivatives of furfuryl amine were synthesized to produce furan-based di-epoxies (FDEs) that were cured by anionic polymerization and with amine curing agents. The furan ring was found to impart additional reactivity for cross-linking and to induce char-forming reactions at higher temperatures. More importantly, the placement of …

Annual Progress In Global Carbon Capture, Utilization, And Storage In 2023, Siyuan Fang, Yun Hang Hu

Michigan Tech Publications

Since the industrial revolution, global anthropogenic CO2 emissions have surged dramatically to unsustainable levels, resulting in severe issues, such as global warming, extreme weather events, and species extinction. In response to this critical situation, extensive efforts have been undertaken across academia, industry, and policymaking sectors to deploy carbon capture, utilization, and storage (CCUS) technologies. Here, we present the annual summary of global CCUS for the year 2023. We begin by discussing the trends of anthropogenic CO2 emissions and atmospheric CO2 concentrations, and then offer an up-to-date summary of progress in academia, industry, and policy, respectively. In academia, we analyze the …

Experimental Investigation On Mechanical Properties Of Pla Reinforced By Bamboo Fiber/Montmorillonite Clay Hybrid Composites And Analysis Of Machining Characteristics, Nirmal Kumar K

Theses and Dissertations

The study presents a comprehensive investigation into the development, characterization, and machining analysis of novel bio-based polymer hybrid composites comprising Polylactic acid (PLA), bamboo powders (BP), and montmorillonite clay particles (MMT). Initially, the hybrid composites were fabricated using a solvent-free stir casting process, optimizing the weight percentages of BP and MMT to enhance mechanical and thermal properties.

Mechanical tests, including tensile, flexural, and impact tests, along with thermal analysis using thermogravimetric analysis and differential scanning calorimetry, were conducted to evaluate the performance of the composites. In the subsequent phases, advanced machining techniques were employed to analyze the machining characteristics of …

Optical Responses Of Hybrid Electromagnetic Nanostructures, Dominic Bosomtwi

Optical Science and Engineering ETDs

Fano resonances result from the interference between a broad background and a narrow state, producing asymmetric scattering profiles. Under specific conditions, destructive interference collapses the Fano resonance width, leading to bound states in the continuum (BICs) that localize light within a nanostructure while maintaining an infinitely high-quality factor (Q-factor).

This dissertation explores the design of nanostructures with multilayer hybrid plasmonic-dielectric metasurfaces using full-wave numerical simulations, facilitating multiple Fano resonances and BICs. By adjusting nanoantenna dimensions, multiple modes are excited at plasmonic-dielectric interfaces, leading to strong interactions and hybridization of energy levels, manifested as Rabi splitting.

These findings enable advancements in …

Article Comprising Bonded Substrate Comprising Nanocrystals And Method Of Making And Using Same, Michael D. Sherburne

AFIT Patents

The present invention relates to devices for measuring property changes via in-situ micro-viscometry and methods of using same. The aforementioned device is inexpensive and can be used to quickly and accurately measure numerous physical and chemical property changes, including but not limited to the rate of chemical cure, change in tack, and rate of mass loss, for example, rate of moisture, solvent and/or plasticizer change.

Synthesis, Crystal Structure, Hirshfeld Surface And Void Analysis Of 2-Amino-1h-Benzimidazolium 2-Hydroxybenzoate, Salmon M. Mukhammadiev, Daminbek A. Ziyatov, Zuhra Ch. Kadirova, Jamshid M. Ashurov, Shahlo Sh. Daminova

CHEMISTRY AND CHEMICAL ENGINEERING

The purpose of this work is determination of crystal structure and Hirschfeld surface void analysis for many intermolecular interactions in the crystal structure of 1,3-dihydro-2H-benzimidazole-2-iminium-2-hydroxy-5-sulfobenzoate.. For the first time, a new organic salt containing organic benzimidazolium cations and sulfosalicylic anions was synthesized and structurally characterized. Hirshfeld surface analysis confirm that in the crystal shape most remarkable contacts are H∙∙∙O (38%) and H∙∙∙H (29.7%) There are some π–π stacking interactions in the crystal shape.

Synthesis Of Cationite Based On Indene, A Secondary Product Of Hydrocarbons Pyrolysis, Saidmansur Sh. Saidobbozov, Suvonkul E. Nurmanov, Dilorom H. Mirkhamitova

CHEMISTRY AND CHEMICAL ENGINEERING

The purpose of the study is extraction of the indene from pyrolysis oil obtained from the pyrolysis of hydrocarbons at the Ustyurt gas processing plant. Indene is isolated by rectification from the composition of pyrolysis oil formed as a by-product of the process of hydrocarbons pyrolysis at the Ustyurt gas processing plant. Polymethyleneindenesulfocationite was synthesized on the basis of isolated indene, and its structure and physicochemical properties were determined. Chromatomass spectrum of pyrolysis oil was obtained and analyzed. The indene fraction and the synthesized polymethyleneindenesulfocationite were analyzed using IR spectroscopy and SEM (scanning electron microscopy). Thermal analysis of cationite was …

Preparation Of Keratin-Containing Protein Compounds From Chickens Feathers Using Hydrochloric Acid, Dilnozakhon I. Tursunova, Oytura S. Maksumova

CHEMISTRY AND CHEMICAL ENGINEERING

The purpose of this work is the preparation of keratin-containing protein compounds from poultry processing waste by hydrolysis with hydrochloric acid, including treatment of the protein with 5% H₂O₂. The process of cleaning feather raw materials using water, liquid soap, NaClO₃, C₂H₅OH, and H₂O_2, and the reaction of its hydrolysis with an aqueous solution of HCl have been studied. The influence of temperature and reaction duration on the hydrolysis process was studied, and its optimal mode was established. It has been shown that the process of …

Synthesis And Research Of Adsorbents And Catalysts Obtained By Processing Of Industrial Wastes, Shuhratqodir T. Gulyamov, Sherzod A. Омоnоv, Shaxnoz B. Jalalova, Dilnoza P. Turdieva, Rufatjon F. Boymonov

CHEMISTRY AND CHEMICAL ENGINEERING

The purposes of the study are the synthesis of granular aluminum oxide and magnesium-aluminum spinel using various residues formed during thermochemical regeneration of adsorbents deactivated by chloride compounds, the physicochemical characteristics and catalytic properties of catalysts. The main parameters for processing aluminum-containing waste using sulfuric acid technology to produce pseudoboehmite have been identified. Adsorbents, as well as carriers and catalysts obtained using pseudoboehmite and alkaline waste have been studied using diffractometry, thermography and elemental analysis. The conditions for the synthesis of mechanically strong granules containing magnesium and calcium aluminates have been determined. Based on pseudoboehmite, aluminum oxide adsorbents with texture, …

Influence Of Solid-Phase And Melt Synthesis Methods On The Structure And Electrochemical Properties Of Na3fe2(Po4)3 Polycrystals, Adolf S. Nogai, Artur A. Nogai, Daniyar E. Uskenbaev, Eleonora A. Nogai, Alexander A. Bush

CHEMISTRY AND CHEMICAL ENGINEERING

The article studies the influence of solid-phase and melt synthesis methods on the structure and electrochemical properties of the Na₃Fe₂(PO₄)₃ polycrystals. If the solid-phase synthesis of the Na₃Fe₂(PO₄)₃ polycrystals (type 1 of samples) is carried out using ceramic technology, initially glassy precursors are first obtained by melting the starting materials under the influence of optical radiation energy at the melt synthesis method, and the Na₃Fe₂(PO₄)₃ polycrystals are obtained after firing (type 2 of samples). With this method, the synthesis …