Materials Science and Engineering Commons^™

The Electrical Resistance Of Metals In Their Hard And Soft States, Eugene A. Avery

Bachelors Theses and Reports, 1928 - 1970

Many investigations have shown that the electrical resistance of soft annealed metals is usually smaller than that of metals in their hard, cold worked state. By annealing cold-worked metals, the electrical resistance decreases to a minimum and then increases upon continued annealing at higher temperatures. The work performed in this investigation upon silver, aluminum, copper, nickel, and soft steel corroborates this idea.

Effect Of Impurities Upon Current Efficiency In The Electrolysis Of Zinc Sulphate Solution, Robert Jess Smith

Bachelors Theses and Reports, 1928 - 1970

There are many elements which are detrimental to the current efficiency in the electrolysis of zinc sulphate solution. Fortunately the majority of these elements are easily removed in the purification process and cause no further trouble. The elements that are likely to cause trouble in ordinary plant operations are antimony, arsenic, cobalt, nickel, manganese and germanium. The following tests were made to determine the mutual effect on the current efficiency when several of the impurities were present in the electrolyte.

A Study Of The Composition Of Zinc Complex Cyanide Solutions By The Conductometric Method, Robert James Woody

Bachelors Theses and Reports, 1928 - 1970

As the method or analysis used up to the present time has failed to give quantitative results in determining the composition of zinc cyanide baths, conductometric methods were adopted in this study. Supplementary tests were also carried out in this investigation.

The Leaching Of Electrodeposition Of Iron, Emmett G. Simmons

Bachelors Theses and Reports, 1928 - 1970

Electrolytic iron as deposited is brittle and therefore must be annealed. After annealing, the material is ductile and closely resembles copper in its behavior under work. It is claimed to be more resistant to corrosion than dead soft iron. It also has the advantage of corroding uniformly ( or­dinary soft iron develops pin holes which shorten its life considerably).

The extreme purity of electrolytic iron namely makes it very suitable as a base metal for alloys. Its ductility opens up a field for use in the manufacture of cold rolled strip, seamless tubes, and wire.

Aventurine Glazes, Felix Fraulini

Bachelors Theses

"The object of this study was to notice the effect produced upon the crystalline growth in the glaze by the variation of B₂O₃, Fe₂O₃, and SiO₂, and to notice the effect of cooling upon the crystalline growth in the glaze"--Scope of Investigation, leaf 3.

The Effect Of Variations In The Rate Of Heating On The P.C.E. Value Of Clays, Kenneth Emerson Evans

Bachelors Theses

"Softening temperature of ceramic materials vary with the rate of heating. Recently much discussion has centered about the proper rate of heating of cones in the P.C.E. test. The most obvious reason for the discussion is that the cones are affected by the rate of heating when tested alone for softening temperature"--Introduction, page 1.

A Comparative Study Of The American Society For Testing Materials Spall Test And The Federal Specifications Spall Test, Justus Jordan Beinlich

Bachelors Theses

"Commercial brands of fireclay brick will be tested with both the American Society for Testing Materials and the Federal Specifications Spall Tests in order to determine whether the two tests are consistent in the indication of resistance to spalling. It is suggested that the properties of a refractory affecting thermal spalling are reversible thermal expansion, elasticity, heat transfer, plastic flow, and strength. It is hoped that it will be possible to explain the discrepancies that may arise in the results of this work in terms of the above physical properties or else find a reasonable agreement between the two tests"--Introduction, …

Study Of The Substitution Of Barite For Barium Carbonate In A Whiteware Body Suitable For Brick Manufacture, Charles Edward Achuff

Bachelors Theses

"Some years ago a method of manufacturing white brick from Georgia Kaolin and apatite rock was developed. This was successful for supplying an attractive white brick to the southern trade, until difficulties were encountered in securing apatite rock of sufficiently high grade to insure the continuance of manufacture of the brick...With the foregoing facts at hand, a study was made of the utilization of an auxiliary flux to replace the apatite rock. A commercial brick was developed, wherein eight (8) per cent of this flux, with forty-two (42) per cent potters flint and fifty (50) per cent Georgia Kaolin was …

The Replacement Of Calcium Carbonate With Calcium Chloride And Calcium Fluoride In A Whiteware Body, Charles Richard Rosenbaum

Bachelors Theses

"In the steel industry it is a common metallurgical practice to add fluospar sic (CaF₂), to a slag to render it more fluid. Ladoo states that the fluospar sic , thus added, forms eutechtics with the silica, alumina, calcium and barium sulfates, rendering them more fusible. The fluospar sic does not decompose, but forms solutions or eutechtics with other substances in the slag. He further states that calcium chloride (CaCl₂) has been used for this purpose but is apparently not as active, necessitating larger quantities per charge. It is also probably more expensive. Calcium carbonate (CaCO₃) is commonly used as …

The Effect Of Reheating Certain Fire Brick On Pyrometric Cone Equivalents, Francis J. Louney

Bachelors Theses

"In a recent survey of the refractories field, especially with respect to the softening point of fire brick, it was suggested to the author that the possibility of reheating certain fire brick, according to the specifications given by the American Society for Testing Materials, might produce a difference in pyrometric cone equivalent from that of the original or unreheated sample. At present, there is considerable lack of knowledge regarding the problem, as evidenced by the utter lack of literature on the softening point resulting from the reheating of fire brick"--Introduction, leaf 1.

Quantitative Microscope Study Of The Flotation Products Of The Anaconda Copper Concentrator, A. M. Gaudin, H. B. Henderson

Bachelors Theses and Reports, 1928 - 1970

This paper presents the results of a quantitative microscope investigation of the flotation products of the Anaconda Copper Concentrator at Anaconda, Montana, undertaken in September 1930 under the terms of the Cornelius F. Kelley Fellowship. This fellowship was established at the Montana School of Mines by the Anaconda Copper Company.

The Recovery Of Copper In Sulphide Ores By Roasting, Leaching, And Electrolysis, Jack S. Greenough

Bachelors Theses and Reports, 1928 - 1970

Sulphide ores of copper are insoluble in dilute sulphuric acid leaching solutions, but a very high extraction can be obtained if the copper ore is in the oxidized condition. The problem is to convert the sulphide into the oxide form. This can be done by giving the sulphide ore an oxidizing-sulphatizing roast. Copper sulphate is soluble in water, so acid will be saved in the leaching process if copper sulphate is present. The iron in the copper sulphide ores is present as pyrite, or in combinations as bornite, or chalcopyrite.

The Effect Of The Fe2: Fe3 Ratio Upon The Current Efficiency In The Electrolysis Of A Copper Sulfate Solution Containing Iron Sulfate, Roy Macfarland

Bachelors Theses and Reports, 1928 - 1970

In the treatment of copper ores by hydro-electro-metallurgical methods, not only is copper deposited, but other metals are also dissolved. In practice it has been found* that iron, under certain conditions, causes the copper to deposit on the cathode as a nonadherent precipitate and also that the iron in solution causes a great decrease in current efficiency, es­pecially when the electrolysis is conducted by operating with a higher current density at the cathode than at the anode.

The present investigation deals with the effects of the two valences of iron on the current efficiency and endeavors to determine whether or …

Some Notes On The Composition Of "Copper Pitch", Richard R. Matthew

Bachelors Theses and Reports, 1928 - 1970

A supply of so-called "copper pitch" ore was received by the Montana Bureau of Mines and Geology in response to a request by them from a resident of Kalispell, who had previously sent a specimen to the Bureau for a mineralogical analysis.

Since this material was little known and had apparently received but little study under a reflec­ting microscope, it was thought that such a study might throw some light on the mineralogical and chemical composition of the material.

The Aplitic Body Bordering Roosevelt Drive South Of Butte, Montana, Edward B. Trueworthy Jr.

Bachelors Theses and Reports, 1928 - 1970

The area studied consists of a large body of aplite situated 12 miles south of Butte. It extends eastward almost to the Butte-Pipestone road, southward to Lime Kiln Hill and westward a distance of 3000 feet.

The petrographic work was supplemented by a map of the area. Special attention was given to those frequent "Limonite Specks" found in the aplite.

The Rate Of Precipitation Of Copper Aluminide In The Silver Rich Silver-Copper-Aluminum Alloys, Thomas Finley Mcbride

Bachelors Theses and Reports, 1928 - 1970

In order to determine the best annealing temperature at which to age-harden the alloys, hardness tests on speci­men annealed for different lengths of time at different temperatures were made.

The Effect Of Hydrogen Overvoltage On The Electrolytic Deposition Of Zinc, John M. Munzenrider, Kenneth O. Sweeney

Bachelors Theses and Reports, 1928 - 1970

In the deposition of metallic zinc by electro­lysis from neutral or acid solution, little difficulty is experienced provided certain impurities are absent from the electrolyte. The use of the process has long been considered as a potential source, patents on the process having been issued as early as 1880. However, the early experimenters failed to realize the importance of impurities in the electrolyte, and for this reason, the process suffered several severe setbacks when commercial plants were built.

The Electrolytic Deposition Of Chromium Upon Aluminum, E. Fults, L. D. Voerge

Bachelors Theses and Reports, 1928 - 1970

The purpose or this investigation is primarily to determine the best conditions for plating chromium on aluminum. The work was carried out with the hope of obtaining coherent deposits, and of determin­ing the conditions under which such deposits may be duplicated.

Pressure Transmission And Green Strength Of Clays As Affected By Time Of Ageing, William Thomas Kay

Bachelors Theses

"Perfect dry pressing could only be attained if the mix possessed the properties of water in so far as pressure transmission is concerned. There are many factors, however, which tend to interfere with the transmixxion sic of pressure in the clay block, such as, - Differences in grain size, friction between the grains, entrapped air, dragging of the clay on the sides of the mould box and many other minor causes. In an effort to solve some the problems that are of vital interest to the Dry Press industry, the Committee on Dry Press Process of the National Brick Manufacturers …

Die Steels And The Heat-Treatment Of Dies For Use In Die Casting Aluminum Base Alloys, Elmer Gammeter

Professional Degree Theses

"Although the casting of metals is an ancient art, it was not until recent years that metals were cast in large quantities in metallic molds. The increasing demands on the industry for greater production brought about this change which essentially involves the introduction of molds capable of producing numerous castings in preference to the use of non-metallic molds which were destroyed in making the casting"--General Consideration of the Die Casting Process, page 1.

Development Of An Artificial Substitute For Firestone, Joseph Edwin Stevens

Bachelors Theses

"Firestone is a natural occurring silica rock which is cut up into brick and shapes and used for lining cupolas. This rock is found in the east, mostly in Pennsylvania. It is dense, having a porosity of 5.6% raw and 16% after firing to cone 18. Its volume expansion upon firing was calculated to be 19.2%. Its appearance shows that it is evidently fine grained silica bonded with a small amount of clay and siliceous cement. This rock has such desirable characteristics for use in cupola linings that it would be of great importance to duplicate this rock synthetically in …

The Effect Of Different Rates Of Ram Movement On The Transmission Of Pressure In Dry Pressed Bodies, Frank Joseph Zvanut

Bachelors Theses

"The object of this investigation was to study the relationship between the rate of ram movement during the initial application of pressure and the transmission of pressure in the dry press process; to study the effect of various rates of ram movement; and, as far as possible, to determine the critical rate for uniform pressure distribution within the body"--Purpose of Investigation, page 4.

The Purification Of Missouri Fire Clays, James Joseph Offutt

Bachelors Theses

"At the present time there appears to be an unlimited supply of high grade fire clay available for most any purpose. But some time in the future there will rise the problem of purifying the low grade clay to such an extent that it will be used in high grade fire clay products. Whatever purification method may be employed it must be applicable on a commercial scale and the cost of purification must be very low. Until the present time little if any work along this line has been reported. Apparently no one has ever attempted any serious efforts to …

The Effect Of Grain Sizing On The Strength And Porosity Of Refractory Grog Bodies, Robert Stafford Green

Bachelors Theses

"The object of this work was to determine the effect of grain sizing on the strength and porosity of grog bodies. The investigation was carried out by the general method of making up bars of varying grain composition and testing them for strength and porosity"--page 1.

The Control Of Anode Corrosion, Edward Arthur Godat

Masters Theses

"This particular study of the control of anode corrosion in connection with the production of zinc by electrolytic deposition from commercial solutions is a continuation of work started at the Missouri School of Mines and Metallurgy in 1929. It is not a new problem or even a new phase of the problem, but rather an attempt to confirm some of the ideas brought out in previous work and to perhaps more definitely establish some of the conclusions drawn from insufficient data, by more extensive tests and by attacking the problem from a slightly different angle"--Introduction, page 1.

Concentration Of An Oxidized Lead Ore From Southeast Missouri, Robert Edward Evans

Masters Theses

"In the main ore bodies of the Southeast Missouri Lead Belt the lead occurs as galena disseminated in dolomite. The concentration in the mills is by tabling and flotation. The grade of the concentrates and the recovery of the galena are excellent. However, in certain areas of some of the mines ore has been developed that does not concentrate so readily. Because of its reddish brown color this ore is known locally as "red ore", and the presence of oxidized lead has been suspected. The purpose of this investigation was to determine the extent to which oxidized lead minerals were …

Preliminary Construction Of A Photo-Electric Cell Concentrator, Stanley S. Williams

Bachelors Theses and Reports, 1928 - 1970

The separation of the valuable portion from the waste portion of an ore is an individual problem for every ore. However, the various methods for accomplishing this end, more or less classify themselves by the physical properties of the constituents of the ore. Most of the properties of minerals have been utilized in some way or other to affect the separation of the valuable from the invaluable parts. Practically nothing has been done so far with color and luster to attain this purpose.

It is believed that the photo—electric cell could also be used in concentrating a certain class of …

Technical Methods Of Analysis For Mill Products, Daniel Elijah Huffman

Professional Degree Theses

"In mining and milling operations it is necessary that the assays be known as soon as possible, also that these results are more accurate than the sampling or the operation that produced the samples. This means that both speed and accuracy must be considered when selecting a method for the analysis of samples"--Technical Methods of Analysis, page 1.

Japan, Van Hoose Smith

Professional Degree Theses

"This ore is mined from a quartz vein which is refined by small seams of graphitic clay material, and the walls of the vein consist of a sort of graphitic shaley material. The above graphitic materials break down under treatment into a rather peculiar clay which was called primary colloidal slime. The milling process in use consists of stamp milling followed by the separation into sand and primary slime in Dorr Duplex Classifiers. The primary slime overflow from these classifiers, which is all practically thru 220 mesh, is thickened and treated by flotation. Normally and with a good supply of …

Georgia Kaolin As The China Clay Constituent In Floor And Wall Tile Bodies, Alfred Arthur Mitchell

Bachelors Theses

"The replacement of the China Clay content in vitreous floor tile and porous wall tile bodies wholly by Georgia sedimentary kaolin would reduce the cost of these bodies being used in our floor and wall tile plants at present. This plastic kaolin is available in large quantities in the State of George, covering an area of about 7500 square miles. It is the intention of this work to substitute this American Clay for the more costly imported English China Clay now being used"--Introduction, page 1.