Materials Science and Engineering Commons^™

Laser-Induced Graphene For Early Disease Detection: A Review, Sri Ramulu Torati, Gymama Slaughter

Center for Bioelectronics Publications

Electrochemical biosensors have been instrumental in early disease detection, facilitating effective monitoring and treatment. The emergence of graphene has significantly advanced sensor technology in various fields, including biomedicine, electronics, and energy. In this landscape, laser‐induced graphene (LIG) has emerged as a superior alternative to conventional graphene synthesis methods. Its straightforward fabrication process and compatibility with wearable devices boost its practicality and potential for real‐world applications. This review highlights the transformative potential of LIG in biosensing, showcasing its contributions to the development of next‐generation diagnostic tools for early disease detection. An overview of the LIG synthesis process and its applications in …

Flexural Post-Cracking Performance Of Macro Synthetic Fiber Reinforced Super Workable Concrete Influenced By Shrinkage-Reducing Admixture, Jingjie Wei, Nima Farzadnia, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Most literature has focused on the effect of shrinkage-reducing admixture (SRA) in shrinkage mitigation resistance of concrete. This study aims to examine the impact of SRA on the efficiency of macro synthetic fibers (MSF) in enhancing the flexural post-cracking behavior of fiber-reinforced super workable concrete (FR-SWC). A comparative analysis of the influence of fiber combinations on the flexural post-cracking behavior of beams is also included. Results showed that a higher dosage of SRA, particularly at 5 % by mass of binder, had a noticeable negative impact on flexural post-cracking performance of beams while exhibiting positive effect on workability and shrinkage …

Electrochemical And Nanomaterial Based Strategies For Nonenzymatic Glucose Detection: A Review, Reagan Aviha, Gymama Slaughter

Center for Bioelectronics Publications

Electrochemical glucose sensing technologies have undergone significant evolution, with continual advancements aimed at improving sensitivity, selectivity, and user convenience. This review systematically explores the development of emerging nonenzymatic glucose sensor designs. Nonenzymatic sensors are critically evaluated for their ability to overcome enzymatic limitations, leveraging novel materials and catalytic mechanisms. Additionally, the emergence of smartphone-integrated glucose monitoring systems is highlighted as the fifth generation, representing a paradigm shift toward personalized, real-time healthcare management. Emphasis is placed on the strategies employed to reduce the working electrode potential and enhance analytical performance. Key analytical metrics and real-sample applicability are evaluated, and persistent challenges …

Development Of Group Iii-V Quantum Confinement-Enabled Detectors: Bias-Tunable Quantum Well Infrared Photodetector (Qwip) And Quantum Dot Scintillation Detector (Qdsd), Gyana R. Biswal

Electronic Theses & Dissertations (2024 - present)

This dissertation discloses the physics, fabrication, characterization, and analysis of two novel types of group III-V semiconductor detectors relying on quantum confinement of carriers, namely voltage-tunable quantum well infrared photodetectors (QWIP) and a high-yield ultrafast quantum dot scintillation detector (QDSD). Both QWIP and QDSD heterostructures presented here were grown on 3” GaAs (001) substrates using molecular beam epitaxy (MBE).

A major part of the dissertation focuses on development of the voltage-tunable QWIPs targeting detection in the mid-wave infrared region (MWIR) (3μm -5μm) and long-wave infrared region (LWIR) (8μm -12μm) with control of sensitivity by the applied bias. The QWIPs utilize …

Enhancing Acetone Gas Sensor Performance With Cobalt Oxide Doping In Lafeo3 Prepared By Co-Precipitation, Andhy Setiawan, Farah Aprisza Sheelmarevaa, Muhamad Taufik Ulhakim, Dani Gustaman Syarif, Endi Suhendi

Journal of Metals, Materials and Minerals

Semiconductor-based gas sensors frequently encounter difficulties in attaining optimal performance due to challenges such as temporal stability and low sensitivity, stemming from their insulating properties at room temperature. To address these limitations, this study proposes a novel approach by preparing cobalt-doped LaFeO3 (LaFeO3-Co) using the co-precipitation method, with doping concentrations of 2.5 mol% and 5.0 mol%. The acetone gas sensors were fabricated into thick films via the screen-printing technique, and their performance was thoroughly characterized. X-ray diffraction (XRD) analysis confirmed a cubic crystal structure, and the addition of 2.5 mol% cobalt was found to reduce the particle size of LaFeO3, …

Enhanced Photocatalytic Reduction Of Cr(Vi) Under Visible Light A Magnetically Separable Tio2-Fe/Fe3o4 Photocatalyst Prepared From Iron Rusty Waste, Khoirunisa Khoirunisa, Novianti Dwi Lestari, Endang Tri Wahyuni, Taufik Abdillah Natsir

Journal of Metals, Materials and Minerals

This research deals with enhancing the visible activity and generating the magnetic property of TiO2 by Fe doping and Fe3O4 impregnation respectively, using rusty iron waste as Fe source. The prepared TiO2-Fe/Fe3O4 photocatalysts were characterized by SR-UV/Visible, FTIR, XRD, and SEM-EDX instruments. The resulting photocatalysts are responsive to visible light and can be separated magnetically and used for photoreduction of Cr (VI) ions. In the photoreduction of Cr(VI) over TiO2-Fe/Fe3O4 photo-catalysts with various amounts of Fe dopant and alteration of Fe3O4 fraction, the photocatalyst mass, irradiation time, and solution pH were optimized. The research results assign that doping Fe to …

Hydroxyl Combined With Nitrogen On Biomass Carbon Promotes The Electrocatalytic H2o2 Selectivity, Jiabi Jiang, Danni Deng, Yuchao Wang, Yingbi Chen, Yu Bai, Meng Wang, Xiang Xiong, Yongpeng Lei

Journal of Metals, Materials and Minerals

Elevating the selectivity of two-electron oxygen reduction reaction (2e‒ ORR) is challenging. Herein, the hydroxyl combined with nitrogen on biomass carbon exhibits a high H2O2 selectivity over a wide potential range of 0 V to 0.5 V vs. RHE, which is nearly 97% at 0.3 V vs. RHE. The combination of hydroxyl and nitrogen improves the adsorption and desorption of intermediates, finally changing the reaction pathway and promoting the selectivity of 2e‒ ORR. The Faradaic efficiency (FE) reaches 98% at 0.3 V vs. RHE. Furthermore, the typical organic pollutants were degraded on site in flow cell. This work illustrates the …

Elucidating The Corrosion Of Carbon Steel In Hybrid Monoethanolamine Solutions Containing Methanol Or N-Methyl-2-Pyrrolidone, Pui Yee Tan, Lian See Tan, Swee Pin Yeap, Peck Loo Kiew, Mee Kee Wong, Azmi Mohd Shariff

Journal of Metals, Materials and Minerals

Corrosion has been a persistent issue in carbon dioxide (CO2) absorption unit that needs to be resolved in order to prolong the life span of the absorber unit. In this regard, understanding the corrosion behaviour, particularly in hybrid monoethanolamine (MEA) solutions, is crucial. This study aims to give detail information on the role of different process parameters, encompassing types of amine solution, temperature, and CO2 loading on the corrosion behaviour of carbon steel in system containing hybrid solution of monoethanolamine (MEA) and methanol (MeOH) or N-methyl-2-pyrrolidone (NMP). Here, the corrosion extent of the carbon steel was evaluated using gravimetric experiments. …

High-Binding Affinity Nanobody Against Sars-Cov-2 Xbb.1.5: Computational-Based Protein Engineering, Phoomintara Longsompurana, Napat Kongtaworn, Rungtiva P. Poo-Arporn, Thanyada Rungrotmongkol

Journal of Metals, Materials and Minerals

The emergence of the SARS-CoV-2 variant XBB.1.5 has triggered a global health crisis by enhancing viral entry into cells via its spike protein. This study addresses the urgent need to develop neutralizing nanobodies (Nbs) to counteract the SARS-CoV-2 virus. Our aim was to identify a lead Nb and enhance its binding affinity to the receptor-binding motif (RBM) on the receptor-binding domain (RBD) of the SARS-CoV-2 spike protein (S-protein) using computational methods. A total of 29 Nbs were screened against the XBB.1.5 RBD using the HDOCK server to select a lead Nb. This investigation revealed that Nb_7KGK exhibited the highest binding …

Electrochemical Study Of Zn-Fe Alloy Coatings On Mild Steel For Automotive Applications, Ramesh Bhat, A. Chitharanjan Hegde

Journal of Metals, Materials and Minerals

This study investigates the electrochemical behavior of Zn-Fe alloy deposited on mild steel (MS) substrates for automotive applications. The electrodeposition of a Zn-Fe alloy onto MS using an acid chloride bath, with 1,2,4-Triazole as an additive to enhance the uniformity of the deposit. The hull cell method was used to optimize the bath composition and operating conditions. The coatings were produced using electrodeposition at varying current densities, with 3 A∙dm‒2 identified as the optimal current density (CD) for achieving uniform coatings. The microstructural properties, including crystallite size and micro-strain, were analyzed using X-ray diffraction (XRD) and Williamson-Hall (W-H) analysis, revealing …

Influence Of The Casting Processes And Aging Times On The Microstructure And Hardness Of Alsi12 Cu Cast Alloys, Said Beroual, Pascal Paillard, Yann Borjon-Piron

Journal of Metals, Materials and Minerals

The present study investigated the effects of the casting processes and aging times on the micro-structure and hardness of commercial AlSi12Cu alloys. The primary goal was to assess how various aging times affect the maximum hardness of the alloy and to evaluate the influence of cooling rates on hardness values obtained from sand casting (SC) and High-pressure die casting (HPDC). For both casting alloys, the solution heat treatment was performed at 540℃, followed by quenching. The alloys were then aged at 180℃ for various durations, ranging from 10 min to 50 h. The results reveal significant microstructural changes in the …

Photodegradation Of Malachite Green Using 2d G-C3n5 Nanosheet: A Promising Metal Free Catalyst, Sonali Biswal, Swayam Aryam Behera, Asima Subhadarshini, P. Ganga Raju Achary, Binita Nanda

Journal of Metals, Materials and Minerals

Environmental issues have become more serious these days due to the growth of modern industries. The paper and textile industries, in particular, were heavily dependent on the printing and discharge of dye, which constantly leaked into the water ecology and constituted a serious risk to public health. Organic wastewater treatment and remediation for its associated risks have received a lot of attention lately. This work explored the potential of the g-C3N5 nanostructure as a novel photocatalyst for malachite green degradation in aqueous solution while exposed to visible light. The nanocomposite was fabricated through an ultrasonicate-assisted technique. A number of analysis …

Regulating Copx/Co Heterostructures For Enhanced Electrocatalytic Activity Toward Hydrazine Oxidation Reaction, Qinquan Lin, Rui Zhang, Changli Yan, Qizhao Hu, Shangbin Sang, Qiumei Wu, Kaiyu Liu, Hongtao Liu

Journal of Metals, Materials and Minerals

Hydrazine hydrate (N2H4∙H2O) is considered an ideal fuel for fuel cells. Constructing a cobalt phosphide/cobalt (CoPx/Co) heterostructure can achieve efficient electrocatalytic activity for hydrazine oxidation reaction. Traditional strategies for constructing CoPx/Co heterostructures took less consideration on the exposure of the active sites. In this study, 3D nanoflower-like nano CoPx/Co heterostructures with highly exposed active sites were obtained on a nickel foam (NF) through a dual-component phosphating strategy, i.e., regulating the relative content of Co and Co(OH)2 with cathodic current density and utilizing the differences in their phosphating behaviors. The potential at 100 mA∙cm‒2 and Tafel slope of the optimized CoPx/Co(375)@NF …

Facile Synthesis Of Bamno3-Zro2 Composite: A Step Towards The Photocatalytic Degradation Of Organic Dye, Kirttimayee Mohanta, Swayam Aryam Behera, Binita Nanda, P. Ganga Raju Achary

Journal of Metals, Materials and Minerals

Environmental contamination by synthetic dyes, particularly Methylene Blue (MB), presents a significant threat to aquatic ecosystems and human health due to their chemical stability and toxicity. This study investigates the photocatalytic degradation of MB using a BaMnO3:ZrO2 composite synthesized in a 1:2 ratio via a straightforward wet-chemical method. Structural and optical characterizations were performed using X-ray diffraction (XRD), Scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), and Ultraviolet-visible diffuse reflectance spectroscopy (UV-DRS). The composite exhibited a reduced bandgap of 2.88 eV and uniform nanoscale morphology, both favorable for visible-light-driven photocatalysis. Under visible-light irradiation, the catalyst achieved 89% degradation efficiency within …

The Effects Of Graphene Nanoplatelets And Microcrystalline Cellulose On The Mechanical Properties Of Fiberglass And Carbon Fiber Composites, Duangjai Srisamut, Nathawat Poopakdee, Warut Thammawichai

Journal of Metals, Materials and Minerals

This study investigated how graphene nanoplatelets (GNP) and microcrystalline cellulose (MCC) affect the mechanical properties of epoxy (EP), carbon fiber (CF), and fiberglass (FG) composites. The tensile and flexural properties of GNP-EP and MCC-EP of  varying reinforcement concentrations were examined. Results indicated significant improvements on tensile and flexural properties by GNP and MCC. At 0.1 wt% GNP, tensile and flexural strengths increased by 10% and 21%, while 2.0 wt% improved flexural modulus by 65%. Similarly, 2.0 wt% MCC improved tensile strength, modulus, and flexural modulus by 11%, 11%, and 46%, respectively, and a 26% increase in flexural strength at 1.0 …

Synthesis Temperature-Driven Enhancements In Bioi Photocatalysis: A Hydrothermal Approach, Sorawit Thueanbangyang, Kittiyaporn Singsumphan, Varunya Atimayulerd, Chutima Nakmuk, Cheewita Suwanchawalit, Montri Aiempanakit

Journal of Metals, Materials and Minerals

Bismuth oxyiodide (BiOI) is a promising photocatalyst for visible-light-driven environmental remediation. However, its photocatalytic efficiency is highly dependent on synthesis conditions, particularly hydrothermal temperature, which governs its structural, optical, and electronic properties. In this study, BiOI was synthesized via a hydrothermal method at temperatures of 120℃, 150℃, 180℃, and 210℃ to investigate the effect of temperature on its photocatalytic performance systematically. Comprehensive characterizations, including X-ray diffraction, field emission scanning electron microscopy, energy-dispersive X-ray spectroscopy, Fourier-transform infrared spectroscopy, UV-vis diffuse reflectance spectroscopy, photoluminescence and photocatalytic degradation studies, were conducted to analyze crystallinity, morphology, band structure and charge transfer properties. The results …

Bagasse Lignin For Single-Used Food Packaging Applications: Uv-Barrier, Antioxidant, Migration And Cytotoxicity, Pawarisa Wijaranakul, Bongkot Hararak, Wanwitoo Wanmoolee, Prapudsorn Wannid, Weerawan Laosiripojana

Journal of Metals, Materials and Minerals

This study examined PLA biocomposite films made from organosolv lignin extracted from Thai agro-waste, specifically sugarcane bagasse (BG), to assess their suitability for food packaging, focusing on their physical, thermal, optical, UV-shielding, antioxidant, and migration properties. Extracted BG-lignin exhibited free radical scavenging ability with an EC50 value of 400 µg/ml, reducing DPPH absorbance by 50%. PLA composite films with BG-lignin dosage from 0.1 to 1.0 wt.% were successfully fabricated via conventional blown film extrusion. Addition of BG-lignin at 0.5 wt.% and 1.0 wt.% to PLA films decreased UV transmittance from 90% to 30% and 12%, respectively, without compromising optical clarity. …

Coating Of Zinc Substrates With Fluorosilane Molecules Using A Water-Treatment Technique As A Pre-Coating Procedure For The Creation Of Superhydrophobic Surfaces, Renz Ronald R. Prieto, Marvin U. Herrera

Journal of Metals, Materials and Minerals

Superhydrophobic surfaces were successfully created when zinc substrates were coated with molecules with low surface energy through grafting of fluorosilane molecules. The zinc substrate underwent water-treatment technique as a pre-coating procedure to enhance the reaction sites for the grafting of fluorosilane molecules. The water contact angle of the samples went as high as 161.1° ± 0.8°. At lower fluorosilane-ethanol soaking times, water contact angles have lower values while at higher soaking time, it has higher water contact angle values. At 240 min fluorosilane-ethanol soaking time, optimum value of water contact angle was achieved. Fluorosilane molecules are widely distributed through the …

Sulfur-Doped Carbon Dots Derived From Caffeine: A Highly Efficient Photocatalyst For Organic Dye Degradation, Ganyaporn Wongwaen, Koranut Dechsri, Praneet Opanasopit, Montri Aiempanakit, Cheewita Suwanchawalit

Journal of Metals, Materials and Minerals

Sulfur-doped carbon dots (S-doped CDs) were synthesized via a solvothermal method using caffeine as a carbon precursor and sodium sulfide as a sulfur source. Characterization using transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), Fourier-transform infrared spectroscopy (FT-IR), ultraviolet -visible (UV-Vis) spectroscopy, and photoluminescence spectroscopy (PL) confirmed successful sulfur incorporation. TEM revealed a uniform size distribution and graphitic structures, while UV-Vis analysis showed a reduction in the bandgap from 3.29 eV to 3.10 eV, improving light absorption and charge carrier separation. The photocatalytic activity of S-doped CDs was evaluated for indigo carmine (IC) dye degradation under UV irradiation, where 2S-CDs …

Impacts Of Calcination Temperature On The Crystallography, Granulometry And Impedance Of Licomno4, Chee Wayne Tan, Zul Hilmi Che Daud, Zainab Asus, Mohd Hasbullah Idris, Izhari Izmi Mazali, Mohd Kameil Abdul Hamid

Journal of Metals, Materials and Minerals

Spinel structured lithium cobalt manganese oxide (LiCoMnO4) which exhibit reduction potential surpassing 5.0 V (vs. Li0 | Li+) was identified to be one of the prospective cathode candidates for next generation lithium-ion electrochemical systems. This article highlights the significance of calcination temperature on the crystallography of the resultant electroceramic compound as well as the corresponding response on the granulometry and impedance of LiCoMnO4. LiCoMnO4 compounds synthesised via sol-gel reaction in the first instance were converted into xerogel and subsequently subjected to facile one-step calcination protocol. Crystallography of the post-calcinated compounds were characterised via powder x-ray diffraction (XRD) technique. Temperature ranging …

Effect Of Lanthanum Doping On Phase Transition, Piezoelectric And Energy Storage Properties Of Lead-Free 0.93(Bi0.5na0.5)Tio3‒0.07batio3 Ceramics, Pathit Premwichit, Songphop Jaila, Sasiporn Prasertpalichat

Journal of Metals, Materials and Minerals

In this study, lead-free (Bi0.465Na0.465Ba0.07)(1–x)LaxTiO3 (x=0.0‒0.04) ceramics were synthesized using a conventional solid-state reaction method. All samples showed a single-phase perovskite structure with pseudocubic symmetry. The dense microstructure revealed a decrease in average grain size as x increased. La3+ addition stabilized polar nanoregions (PNRs), shifting the ferroelectric to relaxor phase transition temperature (TF₋R=104℃ for x=0.0) to below room temperatures as La3+ content increased. This resulted in a transition from a rectangular to a relaxor-like thin P–E loop (x≥0.01), indicating a shift from ferro-electric (FE) to relaxor ferroelectric (RFE), which …

Aluminium Oxide Particles-Containing Organogels For Cleaning Of Optical Glass Surfaces, Galina Vladimirovna Lyamina, Oksana Valerievna Dubinina, Alfa Edison I Lela

Journal of Metals, Materials and Minerals

Hypothesis:  Some types of cleaning methods are not very effective and can actually increase damage to the optical parts being cleaned. As an alternative to these methods, we propose the use of gel-like substances to remove contaminants from optical surfaces. We have developed a method for cleaning optical glass surfaces that uses organogels, which are based on copolymers of methyl methacrylate and methacrylic acid. These organogels are loaded with polyethylene glycol, and aluminum oxide particles (Al2O3), which help to effectively remove contaminants without causing damage to the surface.   Experiments:  Al2O3 nanoparticles prepared by a Nano Spray Dryer were added to …

Effect Of Alloying Additions On Austenite Refinement In Nickel-Alloyed Ductile Cast Irons, Adnan Adib Aahamed

College of Graduate Studies: Theses & Dissertations

The benefits associated with the application of ductile irons are significantly attributed to the control of microstructures, with refinement of austenitic matrix during solidification playing a significant role. Nickel alloyed ductile irons are attractive due to their potential for high ductility and suitability for potential high-temperature applications with stable austenitic microstructure. Refinement of austenite grain structure is thus important to enhance the mechanical properties of the alloyed ductile iron. This research investigates the impact of in-mold additions of different alloying elements on the austenite morphology and grain refinement of nickel-alloyed ductile iron along with the associated mechanical properties. A hypoeutectic …

Enhancing The Mechanical Properties Of Sla 3d-Printed Bio-Resin From Linseed Oil Using Cellulose And Lignin Biopolymers, Chukwunonso A. Ikedionu

College of Graduate Studies: Theses & Dissertations

Abstract

This research explores the development of bio resin from linseed oil by the process of epoxidation and acrylation to produce acrylated epoxidized linseed oil (AELO). Lignin and cellulose biopolymers were added as reinforcement at varying weight fractions of 1 wt.%, 2.5 wt.%, and 5 wt.%, and their mechanical performance was compared against pure AELO. The formulations were printed using an Elegoo SLA 3D printer to create standardized test specimens like tensile bars, compression cylinders, and hardness blocks, which were all prepared according to the ASTM testing standard.

The results indicate that reinforcement effects depend on both filler type and …

A Novel Technique For Improved Measurement Of Graphite And Inclusions In Ductile Iron Contaminated By Boron, Chase Schroeder, Colleen Lehrer, Simon Lekakh, Laura Bartlett

Materials Science and Engineering Faculty Research & Creative Works

The highly heterogeneous microstructure of ductile iron in casting includes graphite particles, non-metallic inclusions, microporosity, and other features, such as carbides distributed in the ferrite–pearlite matrix. Determination and comprehensive quantification of microstructural features are practically important however challenging. An advanced methodology based on an automated SEM/EDX analysis was developed and compared to the standard optical imaging method. In addition to backscattered electron contrast, sensitive to atomic number, a novel methodology added EDX data to identify and classify the multiple structural features at micron resolution thresholding. To quantify the shape of individual phases, the eight chord raster algorithms was used and …

Optical Sensor Instrumentation For Enhanced Continuous Caster Development, Hanok Wondimagegnehu Tekle

Doctoral Dissertations

Fiber-optic sensors are an emerging technology that can enhance process monitoring and control in steelmaking. They are especially valuable in the continuous caster’s harsh environment. This dissertation presents the industrial application and demonstration of three sensor types: single-mode silica fiber with Rayleigh-based Optical Frequency Domain Reflectometry (OFDR), sapphire fiber (single-crystal alumina) with Fiber Bragg Gratings (sFBG), and an in-line Raman spectroscopy probe. Each sensor served a distinct role in the continuous caster. Rayleigh OFDR sensors were embedded in tundishes for distributed thermal mapping at 7-mm spatial resolution across ≈4 m. Measurements were taken during preheating, casting, and ladle exchanges, and …

Re-Crosslinkable Particle For Conformance Control And Temporary Plugging, Yifu Long, Bowen Yu, Baojun Bai, Thomas P. Schuman

Patents

The present invention generally relates to the composition of particle gels for conformance control, well drilling and well treatments. More particularly, this invention relates to swellable polymer particle gels that can re-crosslink, i.e., reassociate and self-heal, at subterranean conditions. These particle gels can be deployed to improve the conformance of water flooding of especially matrix bypass events (MBEs), that are also known as void space conduits. Moreover, these particle gels can be deployed for controlling the water production and increasing of petroleum recovery. The inventive particles can also be deployed as diverter for well stimulation.

Coating Compositions And Methods For Using The Same, Fateme Razaei, Thomas P. Schuman, Glenn C. Morrison

Patents

Coating compositions and methods for using the same are disclosed. The coating compositions can include an aminosilica adsorbent. The coating compositions can adsorb CO2 .

Preparation Of Mocvd-Grown Photocathodes Containing A Strained Gaas/Gaasp Superlattice, G. Blume, A. Masters, J. Grames, M. Stutzman, M. Grau, S. Marsillac

Physics Faculty Publications

In this work, we investigate heat cleaning options for high-polarization GaAs/GaAsP strained-superlattice (SSL) photocathodes with a distributed Bragg reflector (DBR) that were grown using metalorganic chemical vapor deposition (MOCVD). This was done using a microMott polarimeter at Jefferson Lab to optimize both quantum efficiency and polarization. The fabrication process for MOCVD-grown photocathodes does not allow for the inclusion of an arsenic cap, contrary to what is done when fabricating photocathodes using molecular-beam epitaxy (MBE). Without proper preparation, the performance of MOCVD-grown photocathodes can be limited due to surface contamination. Here, we varied both duration and temperature of the heat cleaning …

Advances In Conductive Polymer-Based Flexible Electronics For Multifunctional Applications, Md Abdus Shahid, Md Mostafizur Rahman, Md Tanvir Hossain, Imam Hossain, Md Sohan Sheikh, Md Sunjidur Rahman, Nasir Uddin, Scott W. Donne, Md Ikram Ul Hoque

Michigan Tech Publications

The rapid developments in conductive polymers with flexible electronics over the past years have generated noteworthy attention among researchers and entrepreneurs. Conductive polymers have the distinctive capacity to conduct electricity while still maintaining the lightweight, flexible, and versatile characteristics of polymers. They are crucial for the creation of flexible electronics or gadgets that can stretch, bend, and adapt to different surfaces have sparked momentous interest in electronics, energy storage, sensors, smart textiles, and biomedical applications. This review article offers a comprehensive overview of recent advancements in conductive polymers over the last 15 years, including a bibliometric analysis. The properties of …