Materials Science and Engineering Commons^™

A Pyrrole Modified 3,4-Propylenedioxythiophene Conjugated Polymer As Hole Transport Layer For Efficient And Stable Perovskite Solar Cells, Yuanhao Tang, Ke Ma, Wenhao Shao, Yoon Ho Lee, Ashkan Abtahi, Jiaonan Sun, Hanjun Yang, Aidan H. Coffey, Harindi R. Atapattu, Mustafa Ahmed, Qixuan Hu, Wenzhan Xu, Raunak Dani, Limei Wang, Chenhui Zhu, Kenneth R. Graham, Jianguo Mei, Letian Dou

Chemical and Materials Engineering Faculty Publications

Despite the outstanding electric properties and cost-effectiveness of poly- (3,4-ethylenedioxythiophene) (PEDOT) and its derivatives, their performance as hole transport layer (HTL) materials in conventional perovskite solar cells (PSCs) has lagged behind that of widely used spirobifluorene-based molecules or poly(triaryl amine). This gap is mainly from their poor solubility and energy alignment mismatch. In this work, the design and synthesis of a pyrrole-modified HTL (PPr) based on 3,4-propylenedioxythiophene (ProDOT) are presented for efficient and stable PSCs. As a result of the superior defects passivation ability, excellent contact with perovskite, enhanced hole extraction, and high hydrophobicity, the unencapsulated PPr-based PSCs showed the …

Analysis Of Tar And Oil Derived From Pyrolysis And Copyrolysis Of Waste Plastics And Biomass, Anitha Shankaralinge Gowda, Dimitrios Karadimas, Jeffrey Seay

Chemical and Materials Engineering Faculty Publications

Pyrolysis has been proposed as a potential technology for managing the growing volume of plastic waste generated worldwide. Co-pyrolysis of plastic waste with biomass is a promising technology for generating fuel and chemical products. However, this process generates tar as a waste product. The chemical properties of this tar have yet to be thoroughly analyzed. This study presents the results of gas chromatography–mass spectrometry (GC–MS), Fourier-transform infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA) of oil and tar obtained from the pyrolysis of pure plastics including high-density polyethylene (HDPE), low-density polyethylene (LDPE), polyethylene (PE), polystyrene (PS), and plastic-biomass mixtures. GC–MS analysis …

Membrane Filtration Of Nanoscale Biomaterials: Model System And Membrane Performance Evaluation For Aav2 Viral Vector Clarification And Recovery, Mara Leach, Kearstin Edmonds, Emily Ingram, Rebecca E. Dutch, Ranil Wickramasinghe, Malgorzata Chwatko, Dibakar Bhattacharyya

Chemical and Materials Engineering Faculty Publications

The growing demand for viral vectors as nanoscale therapeutic agents in gene therapy necessitates efficient and scalable purification methods. This study examined the role of nanoscale biomaterials in optimizing viral vector clarification through a model system mimicking real AAV2 crude harvest material. Using lysed HEK293 cells and silica nanoparticles (20 nm) as surrogates for AAV2 crude harvest, we evaluated primary (depth filters) and secondary (membrane-based) filtration processes under different process parameters and solution conditions. These filtration systems were then assessed for their ability to recover nanoscale viral vectors while reducing DNA (without the need for endonuclease treatment), protein, and turbidity. …

Fundamental And Application Of Co-Assembly Of Peptides And Proteins: Experiment And Computation, Newton A. Ihoeghian, Qing Shao

Chemical and Materials Engineering Faculty Publications

Peptides and proteins can co-assemble into various nanostructures based on complementary non-covalent interactions such as electrostatic forces, hydrogen bonding, and hydrophobic associations. These co-assemblies create a design space of functional materials for a wide spectrum of energy, environmental, and biomedical applications. This review focuses on the fundamentals and applications of three co-assembling systems: ultra-short peptides, peptides, and proteins. We will present and discuss experimental studies demonstrating applications in drug delivery, tissue engineering, and biomaterials development. We will also discuss the contribution of computational research, including molecular dynamics simulations and machine learning, to enhance our understanding of assembly mechanisms. Integrating experimental …

Accelerated Aging System For Pinniped Tags, Sean Shermer, Nathan Vasquez, Deekshitha Garige

Undergraduate Scholarship

This project focused on the design of an accelerated aging system intended to evaluate the durability of pinniped identification tags used in marine mammal research. The system was developed in collaboration with the Cal Poly Humboldt Marine Lab and NOAA, under the guidance of Dr. Dawn Goley, to address the limitations of field based durability testing, which is slow, inconsistent, and difficult to reproduce. The primary objective was to create a repeatable laboratory testing framework capable of simulating multiple environmental stressors experienced by pinniped tags. This includes the accelerated tests of UV radiation, mechanical abrasion, temperature cycling and biological fouling. …

A Comparison Of Microcrystal Electron Diffraction And X-Ray Powder Diffraction For The Structural Analysis Of Metal-Organic Frameworks, Erik Biehler, Silvana Pagola, Daniel Stam, Johannes Merkelbach, Christian Jandl, Tarek M. Abdel-Fattah

Chemistry & Biochemistry Faculty Publications

This study successfully implemented microcrystal electron diffraction (microED) and X-ray powder diffraction (XRPD) for the crystal structure determination of a new phase, TAF-CNU-1, Ni(C₈H₄O₄)·3H₂O, solved by microED from single microcrystals in the powder and refined at the kinematic and dynamic electron diffraction theory levels. This nickel metal–organic framework (MOF), together with its cobalt and manganese analogues with formula M (C₈H₄O₄)·2H₂O with M = Mn ^II or Co^II, were synthesized in aqueous media as one-pot preparations from the corresponding hydrated metal chlorides and sodium terephthalate, as a promising `green' synthetic route to moisture-stable MOFs. The crystal structures of the …

Metathesis Or Isomerization: Counteranion Directed Reactivity Of Grubbs I, Paul D. Miller, Joe B. Calkins, Craig A. Bayse, Trandon A. Bender

Chemistry & Biochemistry Faculty Publications

Catalytic isomerization of alkenes has garnered interest for many years, but there are remaining challenges when it comes to thermodynamic selectivity and uncontrolled isomerization. Nonbiased substrates, be it sterically or thermodynamically, remain challenging for many catalysts, with a few examples available in the more modern literature. Herein, we present the controlled isomerization of linear alkenes with a cocatalytic mixture of commercially available catalyst and reagents: Grubbs I, tris(pentafluorophenyl)borane, and triethylsilane. DFT calculations indicate that an observed alkylidyne hydride intermediate is in rapid equilibrium with an alkylidene that binds the alkene substrate. This combination results in a pi-acidic metal and a …

Amphiphilic Tripodal Metalloligands: Synthesis, Coordination Chemistry And Preliminary Catalysis, Austin W. Medley, Paul D. Miller, Craig A. Bayse, Robert D. Pike, Trandon A. Bender

Chemistry & Biochemistry Faculty Publications

Triscatecholate binding has been widely studied in the context of biological systems, supramolecular chemistry, and weak aggregate interactions. However, the utilization of the triscatecholate binding motif for the preparation of metalloligands remains unexplored. Herein, we report the synthesis, structural characterization, and functional studies of a triscatecholate ligand with an appended pyridyl residue as a candidate for such applications. Our findings reveal that the selective formation of cis-triscatecholate-based metalloligands is influenced by electronic effects on the catecholate anions, enabling the targeted synthesis of Al(III), Ga(III), and In(III) triscatecholate metalloligands capable of binding Zn(II) and Ru(II) at the appended pyridyl moiety for …

Flexural Response Of Inflatable Drop-Stitch Panels, Alex J. Watterson

Open Access Master's Theses

All CUI (Controlled Unclassified Information) is U.S. government property and has been removed from this thesis.

Evaluation Of Polymer Coated Fabrics Subjected To Various Multiaxial Stress States, Shane Marx

Open Access Master's Theses

All CUI (Controlled Unclassified Information) is U.S. government property and has been removed from this thesis.

Atomistic Calculations Characterizing Thermodynamic And Mechanical Properties Of High Entropy Alloys, Sarah O'Brien

Theses and Dissertations--Chemical and Materials Engineering

High entropy alloys (HEAs) are an exciting new class of materials. HEAs combine multiple elements in concentrations ranging from 5% to 35%. The large variation in concentrations increases the alloy’s entropy, stabilizing it. The stabilization is due to both an increased configurational entropy and increases the vibrational entropy when the alloy is at higher temperatures. This was seen for both MoNbTaW and FeNiMoW by combining the atomistic techniques: density functional theory (DFT) and density functional perturbation theory (DFPT). For MoNbTaW, the composition plays a large role in stabilizing the alloy over the configuration of elements. For the three-phase alloy, FeNiMoW, …

Analysis Of Ptfe Radial Lip Seals For Wheel Bearing Applications, Madison Vogt

Theses and Dissertations--Mechanical and Aerospace Engineering

A numerical analysis was conducted to investigate the viscoelastic effects of nonlinear materials on the sealing zone and contact pressure distribution of radial lip seals in a conventional geometric topology. The use of nonlinear materials in radial lip seal applications is desirable to improve operation and reliability of rotating machinery due to their high operating temperatures, chemical compatibility, and low friction coefficients. Examples include, but are not limited to, seals within industrial air compressors, turbine engines, aircraft landing systems, chemical processing equipment, and Freon pumps. This work focuses on analyzing the nonlinear viscoelastic response of pure Polytetrafluoroethylene (PTFE) and PTFE …

Growth Kinetics And Stability Of Metal Halide Perovskite Nanocrystals: Influence Of Stirring Speed And Water Exposure, You-Lin Huang

Theses and Dissertations--Mechanical and Aerospace Engineering

Cesium lead bromide (CsPbBr₃) perovskite nanocrystals (NCs) have garnered significant interest due to their exceptional optoelectronic properties, including high photoluminescence quantum yield, tunable bandgap, and excellent carrier dynamics. These attributes make them promising candidates for applications in light-emitting diodes, photovoltaics, and sensing technologies. However, optimizing their synthesis and improving their environmental stability remain critical challenges. This dissertation explores the growth kinetics of CsPbBr₃ NCs, focusing on the effects of stirring speed and water exposure on their structural and optical properties.

The synthesis of CsPbBr₃ NCs was performed using both mechanochemical (MC) and antisolvent methods, enabling an …

Fabricating Silver-Ceria Polymer Nanocomposite Scaffolds For Biomedical Therapeutic Applications, Shreya S. Pawar

Honors Undergraduate Theses

Improper healing of bone fractures and limited regeneration of bone following bone tumor resection remain a prevalent complication worldwide. Long-term effects of this include joint instability, limited movement, and arthritis. Bone infections (osteomyelitis), reactive oxygen species (ROS) generation via excessive inflammation, and underlying conditions such as osteoporosis can contribute to suboptimal bone tissue regeneration. ROS accumulation stimulates osteoblast apoptosis, while promoting osteoclast differentiation. These processes inhibit mineralization and osteogenesis. Conventional therapeutics involve the utilization of drugs and bone grafts. However, these approaches pose limitations and can result in subsequent complications. Microbial infections, ROS accumulation, and excessive inflammations are factors that …

Polymeric Nanocomposites-Based Advanced Coatings For Antimicrobial And Antiviral Applications: A Comprehensive Overview, Rachid Amrhar, Jaspal Singh, Mostafa Eesaee, Pascal Carrière, Alireza Saidi, Phuong Nguyen-Tri

Revues de littérature, synthèses de connaissances

The rise in microbial infections and viral outbreaks has accelerated the development of advanced antibacterial and antiviral coating that effectively minimize infection risks. Amidst rising global health concerns due to infectious diseases, these coatings have emerged as vital solutions for surface protection across various settings. This review focuses on the recent development and in-depth analysis includes synthesis process, inactivation mechanism in photoreactive antimicrobial and antiviral bio-coatings. This review comprehensively explores the development of different nanocomposite materials, including polymers based on metal oxide nanoparticles, metal nanoparticles, graphene-based materials, and organic-inorganic composites. Their practicality and compatibility with diverse surfaces such as ceramics, …

Ultrasound Shear Wave Elastography: Development Of Tissue Models And Investigation Of Shear Wave Variability, Emily J. Miller

Dissertations, Master's Theses and Master's Reports

Ultrasound shear wave elastography (USWE) is an evolving and promising clinical tool for noninvasively measuring in vivo soft tissue biomechanical properties. Assumptions incorporated into the clinical workflow and technical limitations have created gaps between theoretical and clinically derived solutions. The heterogeneity of the fibrotic liver tissue, composition of the background, such as the presence of fatty liver tissue, and the preferred local orientation of the scarred fibrotic liver tissues embedded into the liver parenchyma, may contribute to the uncertainty in USWE measurements. This study aims to systematically investigate four cofounding factors (i.e., size, volume fraction, orientation of the fibrotic inclusions, …

Linking Molecular Structure Evolution To Mechanical Degradation During Environmental Aging In Conventional And Recyclable Epoxy Systems, Ben T. Jewell

Dissertations, Master's Theses and Master's Reports

The long-term performance of polymeric materials in extreme environments is governed by complex chemical and physical aging processes that alter their molecular structure and mechanical integrity. Conventional thermoset epoxies, while widely used in structural applications, are particularly susceptible to oxidative degradation at elevated temperatures, leading to embrittlement and loss of structural integrity. In the first part of this work, diffusion-limited oxidation (DLO) in a bulk structural epoxy was systematically investigated to establish the link between heterogeneous microstructural evolution and macroscopic mechanical degradation. High-temperature oxidation experiments were conducted in a controlled environmental chamber, and the resulting chemical, thermal, and mechanical changes …

Degradation Of Polymers And Polymer Composites In Extreme Environments, Ben T. Jewell

Dissertations, Master's Theses and Master's Reports

Polymeric materials are widely used in engineering applications due to their high strength-to-weight ratio, easy manufacturability, and cost-effectiveness. When incorporated into composites, they provide further performance enhancements, enabling use in demanding structural applications. However, long-term exposure to harsh environments including elevated temperatures, UV radiation, harsh chemicals, and radiation, can drive degradation processes that alter the material’s network structure, and in turn, degrade its mechanical performance. Exposure to thermo-oxidative conditions is one of the most common environments driving polymer degradation, leading to chain scission and crosslinking events, with the resulting oxidative products causing discoloration, reduced ductility, and changes in glass transition …

Supercapacitors With Cotton Shell-Derived Activated Carbons And Porous Polymer Electrolyte Films, Saurabh Singh, Yulin Zhang, S. A. Hashmi, Fuqian Yang

Chemical and Materials Engineering Faculty Publications

Some of the well-known challenges in the field of supercapacitors (SCs), or more specifically, electrical double-layer capacitors (EDLCs), such as low energy density and high cost, have proven to be major barriers to their widespread market success despite having some excellent electrochemical merits such as high-power density and good cyclic stability. In this work, efforts have been made to overcome these gaps and eventually enhance the performance of EDLCs via a cost-effective and eco-friendly approach. To fabricate these EDLCs, a bio-waste, namely, cotton-shell-derived activated carbons (ZnACs) (activated with ZnCl2), was used in a mass ratio of 1 : 2 for …

Improvement Of Cellular Pattern Organization And Clarity Through Centrifugal Force, Lauren E. Mehanna, James D. Boyd, Shelley Remus-Williams, Nicole M. Racca, Dawson P. Spraggins, Martha E. Grady, Brad J. Berron

Chemical and Materials Engineering Faculty Publications

Rapid and strategic cell placement is necessary for high throughput tissue fabrication. Current adhesive cell patterning systems rely on fluidic shear flow to remove cells outside of the patterned regions, but limitations in washing complexity and uniformity prevent adhesive patterns from being widely applied. Centrifugation is commonly used to study the adhesive strength of cells to various substrates; however, the approach has not been applied to selective cell adhesion systems to create highly organized cell patterns. This study shows centrifugation as a promising method to wash cellular patterns after selective binding of cells to the surface has taken place. After …

Integrating Protein Language Model And Molecular Dynamics Simulations To Discover Antibiofouling Peptides, Ibrahim A. Imam, Shea Bailey, Duolin Wang, Shuai Zeng, Dong Xu, Qing Shao

Chemical and Materials Engineering Faculty Publications

Antibiofouling peptide materials prevent the nonspecific adsorption of proteins on devices, enabling them to perform their designed functions as desired in complex biological environments. Due to their importance, research on antibiofouling peptide materials has been one of the central subjects of interfacial engineering. However, only a few antibiofouling peptide sequences have been developed. This narrow scope of antibiofouling peptide materials limits their capacity to adapt to the broad spectrum of application scenarios. To address this issue, we searched for antibiofouling peptides in the vast sequence pool of the microbiome library using a combination of deep learning-based high-throughput search and molecular …

Clarifying The Role Of Η-Phase With Varying Chemistry On Localised Corrosion Of A Cu-Containing 7xxx Al-Alloy By Quasi-In-Situ Tem, S. K. Kairy, Y. Wu, S. Turk, A. Shekhter, Rudolph Buchheit, N. Birbilis

Chemical and Materials Engineering Faculty Publications

Quasi-in-situ transmission electron microscopy was employed to study dissolution associated with η-phase (Mg(Zn,Al,Cu)₂) precipitates in a Cu-containing 7xxx Al-alloy. Two distinct η-phase chemistries, with Cu to (Zn+Mg+Al) ratios ∼0.12 and ∼0.2, were studied in 0.01 M NaCl at pH 6 and 2. In near-neutral NaCl, both η-phase precipitates exhibited ‘duplex’ behaviour, i.e., they were primarily more noble with respect to the surrounding Al-matrix, causing matrix dissolution, and simultaneously established nanoscopic active sites within the noble precipitate itself by generating nanoscale pits. Conversely, η-phase precipitates rapidly dealloyed in acidic NaCl, forming nocrystalline Cu remnants containing twins, which subsequently caused …

Enhancing Intrinsic Ductility In Vnbmotaw High Entropy Alloy: A Combinatorial Investigation With Experimental Evaluation Of Theoretical Predictions, Taohid Bin Nur Tuhser, Ian Stewart Winter, Daryl Chrzan, Thomas John Balk

Chemical and Materials Engineering Faculty Publications

The application of refractory high entropy alloys (RHEAs) as engineering materials has been hindered by their poor inherent ductility. In this study, a novel approach combining thin film combinatorial screening with fragmentation testing was employed to identify intrinsically ductile alloy compositions. Inspired by the physics-based intrinsic ductility parameter, the ‘χ-parameter,’ we investigated the replacement of group VI elements (W/Mo) with group V elements (V, Nb, Ta) in the VNbMoTaW system. Conventional combinatorial analyses, including composition, phase, and hardness assessments, were conducted across a wide range of non-equiatomic configurations. The results revealed a broad compositional space favoring a single-phase body-centered cubic …

Photocatalytic Performance Of Ba₀.₈Ca₀.₂Tio₃ Composite For Norfloxacin Removal In Aqueous Solutions, Raj Mohanty, Swayam Aryam Behera, Asima Subhadarshini, Binita Nanda, P. Ganga Raju Achary

Journal of Metals, Materials and Minerals

This study investigates the degradation of norfloxacin using a Ba0.8Ca0.2TiO3 (BCTO) perovskite composite synthesized via a simple solid-state method. Variety of characterization techniques, including photoluminescence spectra, powder X-Ray Diffraction, UV-Vis Diffuse Reflectance Spectra, FE-SEM and Fourier-Transform Infrared spectra confirm the structural and optical properties of BCTO. Electrical characterization further elucidates its conductive properties. The BCTO composite demonstrates an impressive 87% degradation rate of norfloxacin, attributed to its reduced electron-hole recombination, enhanced light harvestation, and improved charge carrier mobility. Kinetic studies indicate that the degradation process adheres to a pseudo-first-order model, with BCTO outperforming both pure BaTiO3 and conventional photocatalysts. These …

Improving The Mechanical Performance Of 45s5 3d Scaffolds Through The Particles Of Barium Titanate Ceramics, Surirat Yotthuan, Usanee Pantulap, Nuttawan Sawangboon, Ornuma Tungsanguan, Ekarat Meechoowas, Kansiree Kaewmorakot, Nathaporn Uthaichai, Theerachai Bongkarn

Journal of Metals, Materials and Minerals

Bioglass® 45S5 is widely used in bone tissue engineering due to its excellent bioactivity. However, its low mechanical strength remains a major limitation. In this study, 25 wt% barium titanate (BaTiO3; BT) was incorporated into 45S5 scaffolds to improve mechanical performance and modulate bioactivity. The 3D scaffolds were fabricated using the foam replication method and exhibited interconnected porosity, with average pore sizes of 471 ± 94 μm (45S5) and 598 ± 58 μm (45S5/BT25), closely resembling human bone. The addition of BT increased the density and compressive strength of the scaffolds to 2.89 ± 0.18 g∙cm‒3 and 2.0 ± 0.2 …

Synthesis And Characterization Of Silica Nanoparticles From Solar Panel Glass Cullet, Pathomporn Ussawanawachat, Nithiwach Nawaukkaratharnant, Apirat Theerapapvisetpong

Journal of Metals, Materials and Minerals

The rapid growth of solar energy as a renewable resource has led to a significant increase in discarded solar panels. Recycling their glass components, especially fine cullet fragments, remains a major challenge due to impurity levels and processing limitations. This study proposes a sustainable approach to recycle solar panel glass cullet into high-purity silica nanoparticles using alkali fusion followed by acid precipitation. Process conditions including cullet to NaOH ratio, fusion temperature, and surfactant addition were optimized. The highest silica yield of 60.26% was achieved at a 1:1.4 cullet to NaOH ratio and 500℃. Polyethylene glycol (PEG 1000) was used as …

Laser Ablation Behavior And Ablation Threshold Of Entropy-Controlled Perovskite Coatings, Shuo Wang, Junyang Lu, Mengqing Zhang, Jiayi Zheng, Tong Zhang

Journal of Metals, Materials and Minerals

The protection threshold of laser ablation resistant materials lags behind the development of laser power density. Single-functional laser ablation resistant materials can no longer meet the practical needs. High-entropy perovskites with infinite chemical composition, tunable bandgap structure, and efficient thermal management capabilities provide new ideas for developing novel high-reflectivity and low-thermal-conductivity multifunctional laser ablation resistant materials. Herein, leveraging these unique advantages of high-entropy perovskites in optics and thermodynamics, four entropy-controlled perovskite coatings, Ba(Zn1/2Ta1/2)O3 (BZTO), Ba(Zn1/3Ta1/3Nb1/3)O3 (BZTNO), Ba(Zn1/4Ta1/4Nb1/4Ti1/4)O3 (BZTNTO) and Ba(Zn1/5Ta1/5Nb1/5Ti1/5Zr1/5)O3 (BZTNTZO) are designed. Through time-dependent laser ablation experiments, the optical and thermal properties are comprehensively evaluated. And laser ablation behavior …

Downstreaming Of Natural Materials Huta Ginjang Quartz Sand Doped With Nd2o3 For Laser Medium Application, Juniastel Rajagukguk, Jakrapong Kaewkhao

Journal of Metals, Materials and Minerals

The QSBoBa glasses with chemical formula 10 Quartz sand + (50-x) B2O3 + 10BaO + 30Na2O + xNd2O3 (x = 0, 0.5, 1, 1.5, and 2 mol%) were prepared by a conventional melt-quenching technique. The successfully fabricated glass samples will be analyzed based on their physical, structural, optical and luminescent properties. The XRD and FTIR spectra have been included to observe the complete structural properties. Optical absorption spectra revealed several characteristic transitions, with a prominent hypersensitive transition 4I9/2→4G5/2 at 584 nm, indicating an increasing asymmetry and disorder at higher Nd3+ concentrations. The photoluminescence emission spectra demonstrated strong radiative transitions of …

Crack Development Of Electroplated Niw Alloys And Their Wettability And Tribological Properties, Jidsucha Darayen, Suwat Ploypech, Martin Metzner, Claudia Beatriz Dos Santos, Petch Jearanaisilawong, Yuttanant Boonyongmaneerat

Journal of Metals, Materials and Minerals

This study investigates how sodium tungstate concentration (20–46 wt.%) and current density (40–60 A/dm²) affect the microstructure, wettability, mechanical properties, and tribological behavior of electrodeposited Ni-W coatings. Results show that increasing current density markedly raises crack density (from <100 to >400 cracks/cm²), while tungstate concentration has minimal effect. XRD confirms Ni-W solid solution formation, with higher tungsten content refining grains and increasing hardness—peaking at 900 HV at 50 A/dm² (an 80% rise from 500 HV at 40 A/dm²). However, excessive stress at 60 A/dm² leads to microcracking and hardness plateauing (~650–700 HV). Higher crack density improves wettability (contact angle ~17°), enhancing lubricant …

Upcycled Waste-Derived Triboelectric Nanogenerator For Sustainable Energy Harvesting, Archana Panda, Basanta Kumar Panigrahi, Subhendu Pati, Sunit Gourav Mohanty, Kushal Ruthvik Kaja

Journal of Metals, Materials and Minerals

The proliferation of disposable paper-based materials in laboratories has raised significant environmental concerns due to their rapid discard and accumulation. This study explores the upcycling of commonly discarded laboratory waste, specifically butter paper and polyurethane (PU) foam, into a single-electrode triboelectric nanogenerator (TENG) for mechanical energy harvesting. The fabricated device employs butter paper as the positive triboelectric layer and PU foam as the negative layer, with an aluminium tape electrode. Electrical tests reveal a peak voltage of 21 V and current of 47 nA, reaching a maximum power of 438 nW at 500 MΩ load. The TENG demonstrates stable performance …