Power and Energy Commons^™

High Temperature Silicon Carbide Mixed-Signal Circuits For Integrated Control And Data Acquisition, Ashfaqur Rahman

Graduate Theses and Dissertations

Wide bandgap semiconductor materials such as gallium nitride (GaN) and silicon carbide have grown in popularity as a substrate for power devices for high temperature and high voltage applications over the last two decades. Recent research has been focused on the design of integrated circuits for protection and control in these wide bandgap materials. The ICs developed in SiC and GaN can not only complement the power devices in high voltage and high frequency applications, but can also be used for standalone high temperature control and data acquisition circuitry.

This dissertation work aims to explore the possibilities in high temperature …

Model Development And Validation For Wind Generation Transmission Systems, Mahmood Shihadeh Saadeh

Graduate Theses and Dissertations

In this research a new benchmark system is proposed for wind energy transmission systems. New model development, validation, and calibration methods for power transmission systems are proposed and implemented as well. First, a model reduction criteria is chosen based on electrical interconnection and geographical information. Model development is then done using reduction techniques on an operation model provided by a transmission operator based on the chosen criteria. Then model validation is performed using actual PMU synchrophasor measurements provided by a utility company. The model development and validation process ensures the accuracy of the developed model and makes for a realistic …

Swat Model Simulation Of Bioenergy Crop Impacts On Water Quality In Cache River Watershed, Eeshan Kumar

Graduate Theses and Dissertations

Energy security through increased biofuel production is one of the components of the Energy Independence and Security Act (EISA) 2007. As per EISA 2007 mandate, appropriate independent research institutes are required to assess concerns to natural biodiversity due to biofuel production and report it to the Congress through the Environment Protection Agency (EPA). Planners, researchers, and agencies concerned with environmental regulations, ideally, would like to have location-specific information about the impacts for developing appropriate management interventions. This study examines long-term impacts on water quality in response to targeted (i.e. marginal lands) production of biofuel crops by setting up two SWAT …

Industrial Energy Consumption, Benchmarking, And Analysis In The United States, Daniel Maldonado

Mechanical Engineering Undergraduate Honors Theses

The purpose of this paper is to analyze the energy consumption of the industrial sector in the United States, and to identify the tools that can be used to minimize the consumption and improve the energy efficiency of all facilities in the country. The first part of the paper is a historical analysis of the industrial sector energy consumption, where the different energy sources are identified. The second part details different electronic tools that will provide facilities the ability of performing benchmarking, in order to understand their energy performance. Finally, the third part of this paper provides information about the …

Dual-Input Dc-To-Dc Converter Topologies And Control Schemes, Shaun Alan Stickel

Boise State University Theses and Dissertations

Dual-input DC-to-DC converters are power supplies that draw power from two sources simultaneously and deliver power to a single load, the ratio of power drawn from each source and be held constant with changes in the load. Applications for dual-input power supplies are computer systems, mobile systems using energy harvesting, and systems needing redundant power supplies. This writing covers the operation and control of dual-input DC-to-DC converters that implement a non-inverting buck-boost function and utilize only a single power path.

Traditionally, a dual-input power supply is created by placing two standard power paths in parallel. This adds considerable control complexity …

High-Frequency Transformer Design For Solid-State Transformers In Electric Power Distribution Systems, Roderick Javier Garcia Montoya

Graduate Theses and Dissertations

The objective of this thesis is to present a high- or medium-frequency transformer design methodology for Solid-State Transformer (SST) applications. SSTs have been proposed as a replacement of the traditional 50/60 Hz transformer in applications demanding high-power density. Moreover, due to the high penetration of distributed generation, DC grids, energy storage systems, and sensitive loads, SSTs have been considered as an enabling technology for envisioned future energy systems. These applications demand additional functionalities that may not be achieved with traditional transformers. For example, active power flow control, harmonic suppression, voltage regulation, voltage sag compensation, and reduced size and volume.

In …

The Battery Energy Storage System (Bess) Design Option For On-Campus Photovoltaic Charging Station (Pv-Cs), Ayda Esfandyari, Brian Norton, Michael Conlon, Sarah Mccormack

Conference Papers

As the application of Light weight Electric Vehicles (LEVs) increase in communities, Technological University Dublin (DIT) uses these small vehicles for short distance journeys around its 78 acre campus of “Grangegorman” located in inner Dublin city, Ireland. This paper presents an introduction to the campus Photovoltaic Charging Station (PV-CS) that generates clean electricity from the sun and charges the LEVs batteries which can lead to reduction of CO2 emissions, along with fulfillment of national and international green sustainability targets. Based on the evaluation of possible options for PV-CS design, the optimal design configuration was chosen as a "Battery Energy Storage …

A Combined Energy And Geoengineering Optimization Model (Ceagom) For Climate Policy Analysis, John George Anasis

Dissertations and Theses

One of the greatest challenges that will face humanity in the 21^st century is the issue of climate change brought about by emissions of greenhouse gases. Energy use is one of the primary sources of greenhouse gas emissions. However, it is also one of the most important contributors to improved human welfare over the past two centuries and will continue to be so for years to come. This quandary has led a number of researchers to suggest that geoengineering may be required in order to allow for continued use of fossil fuels while at the same time mitigating the …

A Study Of Ion And Electron Responses To A Dc Electric Field In A Hydrocarbon Flame, Stewart Jacobs

Von Braun Symposium Student Posters

No abstract provided.

Short Review On Electrochemical Energy Storage, Hong Li, Ying-Chun Lyu

Journal of Electrochemistry

Energy storage is a critical supporting technology in many fields such as energy, information, transportation, and healthcare, aerospace, advanced manufacture, advanced equipment, national security. Electrochemical energy storage technique has been widely applied and is developing continuously. In this article, the energy storage mechanism, technical indicators and technology ready level in electrochemical energy storage are summarized. Mainly based on lithium ion batteries, untraditional electrochemical issues in electrochemical energy storage devices are described from the perspective of fundamental science. These issues deal mainly with thermodynamics, kinetics, size effect, asymmetric system, asymmetric reaction path, surface phenomenon, hybrid ion transportation, and solid state battery. …

Preparations And Properties Of Polybenzimidazole/Polyvinylbenzyl Crosslinked Composite Membranes For High Temperature Proton Exchange Membrane Fuel Cells, Jin-Kai Hao, Yong-Yi Jiang, Zhen Wang, Xiao-Jin Li, Zhi-Gang Shao, Bao-Lian Yi

Journal of Electrochemistry

In order to increase the chemical stability of polybenzimidazole (PBl) membrane, a highly stable polymer, poly vinyl. benzyl chloride (PVBC), was chosen as the macromolecular crosslinker, and 1H-1,2,4-triazol was adopted to prepare the crosslinked PBI-based membranes. The influence of the PVBC amount on membrane characteristic was investigated in detail. The results indi. cated that the crosslinked structure of the membrane effectively improved the chemical stability, and at the same time, the mem. brane presented good mechanical property and proton conductivity. The fuel cell performance for the membrane was tested with hy. drogen and oxygen single cell without humidification at 150 …

Review For Applications Of "Lead Carbon" Batteries In Energy Storage System, Yong-Quan Ma, Ke Ke, Da-Ming Gu

Journal of Electrochemistry

Three types of “lead carbon” batteries are introduced by comparing their advantages and disadvantages. Then their applications in energy storage system (ESS), especially in the field of renewable energy power generation, are discussed. The prospects and potential applications of “lead carbon” batteries in EES for electric power supply system are analyzed by combining the state-of-the-art techniques in this field.

Impact Of Water Content On The Performance Of Lifepo4 Based Lithium-Ion Battery, Jun-Ting Niu, Lin Sun, Shu-Wen Kang, Zhen-Wei Zhao, Zi-Feng Ma

Journal of Electrochemistry

Through different dry conditions and measuring by moisture test instrument, cathode pole pieces with different water contents of 0.3‰ ~ 0.7‰ were obtained to prepare lithium-ion batteries. Cycling performance and high rate performance at 1C ~ 5C discharge rates were tested. Moreover, ASR performances of LiFePO4 base lithium-ion batteries after 200 cycles with different water contents were investigated by EIS. The results showed that the cycle performance and rate performance were closely related to the water content of the electrode. When the water content went up to 0.6‰ the cycle stability and rate performance fell. Meanwhile, the internal resistance and …

Sulfonated-Graphene/Nafion Composite Membrane For All Vanadium Redox Flow Batteries, Da-Wei Yang, Yan-Qing Dong, Jing-Min Fan, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

Nafion membrane has been widely used in fuel cells due to its good proton conductivity, chemical and mechanical stabilities. However, the well-developed water channels in Nafion membrane have restricted its application in all vanadium redox flow batteries owing to the high permeation of vanadium ions and the cost. In this work, the water adsorption rate, resistivity and transference number of vanadium ions of sulfonated-graphene/Nafion composite membrane were investigated and compared with those of Nafion membrane in an effort to overcome the abovementioned drawbacks. It was found that the area resistivity and permeation rate of sulfonated-graphene/Nafion composite membrane were significantly reduced …

Research Progress Of Secondary Sodium-Air Batteries, San-Pei Zhang, Zhao-Yin Wen, Jun Jin, Xiang-Wei Wu, Ying-Ying Hu, Mei-Fen Wu

Journal of Electrochemistry

Rechargeable sodium-air batteries have been the focus in the fields of batteries and energy storage recently, owing to their high specific energy density (1600 Wh·kg^-1), an equilibrium discharge potential of 2.3 V and earth-abundant sodium element However, research on sodium-air cells is still in an infant age and presents many scientific issues. Based on recently reported work and our own experience on sodium-based batteries, this review summarizes the research progress related to the critical scientific is sues of secondary sodium-air batteries and the application prospect of sodium-air battery.

Latest Progresses In Vanadium Flow Battery Technologies And Applications, Xiao-Li Wang, Yu Zhang, Hua-Min Zhang

Journal of Electrochemistry

With virtues of high safety, long cycle life, friend environment and state of charge easy monitoring, vanadium flow battery has become an effective technique for large scale energy storage. United States, Japan, Europe and other developed countries are actively promoting the developments of vanadium flow battery technology and related equipments. In this paper, the performance of containerized vanadium flow battery, which was newly developed by Rongke Power (RKP) and Dalian Institute of Chemical Physics, was introduced. The operation data of 5 MW/10 MWh vanadium flow battery energy storage station was displayed. Finally, it is pointed out that reducing the cost, …

Development Of Proton Conduction Membranes In Application Of Vanadium Flow Battery, Le-Tu Qingge, Wei-Nan Guo, Ping Liu, Bao-Guo Wang

Journal of Electrochemistry

The polymeric hydrophilic/hydrophobic interactions into membrane formation were introduced. A general and straightforward strategy for preparing membranes with nanometer-scale pores was suggested by utilization of hydrophilic/hydrophobic interactions to generate phase separation and removal of polyion aggregates through water immersion. Poly(vinylidene fluoride) (PVDF) and sodium allyl sulfonate (SAS) serve as the membrane material and pore-generator, respectively, resulting in chemically stable and oxidation-resistant membranes with various potential applications. Following the same procedure invented to produce the laboratory-scale membranes, the scale-up process to manufacture large-area membranes was completed. The obtained membrane exhibited the conductivity of 3.5×10^-2 S•cm^-1, thickness of 100 …

Characterization Of The Separator With Thermal-Shutdown Layer For Use In Lithium Batteries, Li Bai, Yong-Jian Huai, Xin-Ping Ai, Hai Jia

Journal of Electrochemistry

In this paper, the lithium ion battery coated with the thermal-shutdown functional layer has been introduced. The shutdown temperature of the separator could be decreased by using the melting point of thermal-shutdown functional layer. When the internal battery environment reached a critical temperature, the functional layer melted and coated the anode/separator with a non-conductive barrier, halting Li-ion transport and shutting down the cell permanently. The results showed that the functional layer did not affect the resistance, rate performance and cycle life. It was found the functional layer can significantly improve the safety of the battery when misused.

Effects Of Microstructures Of Active Material On Performance Of Vrla Battery, Lei Jiang, Shou-Zhong Yi

Journal of Electrochemistry

The structure, morphology and content of the as-prepared and the processed samples were characterized by the means of SEM and XRD. The discharge capacities and cycle life performances of the as-prepared and the processed samples were tested by electrochemical measurements with different rates. The results indicated that the 4BS technology which can affect the plate design, deep cycle capability and cycle life is a basic technology for the VRLA batteries. It was also confirmed that the contents and structures of α-PbO₂ and β-PbO₂ formed with different processing conditions can affect the performance of the VRLA batteries, suggesting that …

Preparation And Performance Of Lithium-Rich Manganese Layered Materialsâ 0.6li[Li1/3Mn2/3]O2·0.4liniXMnYCo1-X-YO2(X < 0.6, Y > 0), Hai-Lan Feng, Ya-Fei Liu, Yan-Bin Chen

Journal of Electrochemistry

Lithium-rich manganese based cathode materials 0.6Li[Li_1/3Mn_2/3]O₂⋅0.4LiNi_xMn_yCo_1-x-yO₂ (x < 0.6, y > 0) were synthesized by carbonate co-precipitation and high temperature solid-state reaction. The structures and morphologies of the as-prepared materials were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM). The results of high temperature in-situ XRD test show that the lattice parameters change significantly with increasing temperature and Ni content. The cation mixing gets serious and the spinel phase appears in the high Ni content samples when the temperature is up to 800 oC. Under voltages ranging from 2.0 to …

Bidirectional Ac-Dc Converter For Vehicle-To-Grid (V2g) Applications, Arjun Raj Prabu Andhra Sridhar

Master's Theses (2009 -)

Electric vehicles are growing at a rapid pace in the internal combustion engine dominated transportation sector, and bring environmental and economic benefits to society. Electric vehicles produce nearly zero carbon emission, provided that they are charged through renewable energy sources. Electric vehicles reduce our dependency on foreign oil and also offer additional benefits like Vehicle-to-grid (V2G). V2G is a technology that allows electric energy stored in the electric vehicle batteries to be returned to the grid during peak demand. V2G can also provide voltage regulation, voltage shaving, reactive power compensation and distributed generation. This necessitates that an electric vehicle battery …

Performance Limiting Factors Of Cu2znsn(Sxse1-X)4 Solar Cells Prepared By Thermal Evaporation, Sandip Das, Raghu N. Bhattacharya, Krishna C. Mandal

Faculty Articles

Cu2ZnSn(SxSe1−x)4 (CZTSSe) thin film solar cells have been prepared by vacuum-based thermal evaporation of metal and binary sulfide precursors followed by annealing in a mixed chalcogen vapor at 550 °C for one hour. The Zn/Sn ratio in the precursor was varied from 0.75 to 1.50 keeping the Cu/(Zn+Sn) ratio constant at 0.7. The best performing solar cell was obtained with a final film composition of Cu/(Zn+Sn)=0.77 and Zn/Sn=1.13 corresponding to a Zn/Sn ratio of 0.9 in the precursor. The champion cell exhibited an open-circuit voltage (VOC) of 506 mV, short-circuit current density (J …

Improving Operator Situational Awareness With Wide Area Geographic Data View Displays Of The Electric Power Grid, Esa M. Rantanen, Limor Hochberg, Diego Klabjan, Mingyang Di

Articles

To reduce clutter on wide-area geographic data view displays of electric power systems, substations in geographically compact areas should be spread out and line overlaps and intersections minimized. Such pat- terns optimized with respect to given constraints can be modeled as a multicommodity flow problem. Due to the size of the developed model, we developed two clustering-based iterative algorithms to decompose the global network into smaller regions and then iteratively solve the subproblem in each region by readjusting some values. Three solutions were selected for experimental evaluation. The experimental results were somewhat inconclusive, due to naïve participants, simple task, and …

Accelerated Aging Test On Multiple Xlpe Mv Cables Simultaneously To Induce Water Trees, Shane Conlan, Jane Courtney, Tom Looby

Conference papers

The objective of this paper is to develop an accelerated ageing test to induce water tree growth which is capable of testing up to ten 10 kV cable samples simultaneously. An existing accelerated ageing method was used as a basis for this project. This method uses a high frequency power supply (3 kHz) to achieve a test duration of 14 days. Modifications were made to this method to allow for multiple samples to be tested simultaneously. A specially designed variable inductor was utilised in a parallel RLC resonance circuit. This resonance circuit limits the current draw from a high frequency …

Modeling And Test Of The Efficiency Of Electronic Speed Controllers For Brushless Dc Motors, Clayton R. Green

Master's Theses

Small electric uninhabited aerial vehicles (UAV) represent a rapidly expanding market requiring optimization in both efficiency and weight; efficiency is critical during cruise or loiter where the vehicle operates at part power for up to 99% of the mission time. Of the four components (battery, motor, propeller, and electronic speed controller (ESC)) of the electric propulsion system used in small UAVs, the ESC has no accepted performance model and almost no published performance data. To collect performance data, instrumentation was developed to measure electrical power in and out of the ESC using the two wattmeter method and current sense resistors; …

Fast Sequence Component Analysis For Attack Detection In Synchrophasor Networks, Jordan Landford, Rich Meier, Richard Barella, Xinghui Zhao, Robert B. Bass, Scott Wallace

Electrical and Computer Engineering Faculty Publications and Presentations

Modern power systems have begun integrating synchrophasor technologies into part of daily operations. Given the amount of solutions offered and the maturity rate of application development it is not a matter of "if" but a matter of "when" in regards to these technologies becoming ubiquitous in control centers around the world. While the benefits are numerous, the functionality of operator-level applications can easily be nullified by injection of deceptive data signals disguised as genuine measurements. Such deceptive action is a common precursor to nefarious, often malicious activity. A correlation coefficient characterization and machine learning methodology are proposed to detect and …

Synthesis, Structure And Electrochemical Performance Of Na2Mnsio4/C Cathode Material For Na-Ion Batteries, Shou-Ding Li, Jiang-Huai Guo, Yong Xie, Jin-Xiao Mi, Yong Yang

Journal of Electrochemistry

As a promising cathode material for sodium ion batteries, pure phase Na₂MnSiO₄/C nanocomposite was successfully synthesized by a sol-gel method with a citric acid as a complex agent. The as prepared material was characterized by XRD, FTIR, SEM and TEM techniques. XRD and Rietveld refinement results indicated that the sample was indexed as monoclinic structure with space group of Pn. It was observed by SEM and TEM that the obtained product consisted of micro-scaled secondary particles, which were composed of NaMnSiO₄ nanocrystallites and amorphous carbon network. More importantly, the uniform carbon network in the …

Preparation And Characterization Of Carbon Supported Pd-Sb Composite Nanocatalysts For Formic Acid Electrooxidation, Long-Long Wang, Xiao-Lu Cao, Ya-Jun Wang, Jin-Hao Ping, Qiao-Xia Li

Journal of Electrochemistry

Palladium is considered as an efficient anode catalyst with high catalytic activity for electrooxidation of formic acid. To further improve the catalytic activity and stability, alloying or surface modification with Sb is an effective way. In this work, the well dispersed carbon supported Pd-Sb composite nanocatalysts (Pd-Sb/C) were synthesized by traditional impregnation reduction method with trisodium citrate as the complexing agent, sodium borohydride as the reducing agent. The morphologies of Pd-Sb/C and the effects of molar ratio of Pd to Sb on the electrocatalytic properties of Pd-Sb/C for HCOOH electrooxidation were studied. The XRD and XPS analyses on the as-prepared …

Essentials For On-Campus Photovoltaic Charging Station(Pv-Cs): Grangegorman, Ayda Esfandyari, Brian Norton, Michael Conlon, Sarah Mccormack

Conference Papers

As Light weight Electric Vehicles (LEVs) are gaining interest, Technological University Dublin (DIT) realises the value and application of these vehicles for short distance commutes around its newly built campus of “Grangegorman” located in inner Dublin city. Introduction of the campus Photovoltaic Charging Station (PV-CS) that generates clean electricity from the sun and charges the LEV’s batteries can help achieving Ireland’s 2020 targets on both national and international levels. This paper highlights the design essentials of on-campus PV-CS, via assessments of: LEV load consumption, vehicle tracking and sizing of the storage unit. The pattern for LEVs charging and load consumption …

Preparation And Enhanced Rate Capability Of Spinel Limn1.9Al0.1O3.95F0.05, Jun-Yan Hu, Meng-Meng Wang, Hong-Tao Liu

Journal of Electrochemistry

Spinel LiMn_1.9Al_0.1O_3.95F_0.05 cathode materials with good crystallinity were synthesized by a sol-gel process followed with a high-temperature solid reaction. The effects of partial substitution of Al for Mn, and F for O on the structure and the electrochemical performance were investigated. The results showed that LiMn_1.9Al_0.1O_3.95F_0.05 exhibited the same crystalline state as LiMn₂O₄, but much better electrochemical stability at higher rate cycling. As a result, LiMn_1.9Al_0.1O_3.95F_0.05 could maintain stable electrochemical lithium storage even suffering from …