Power and Energy Commons^™

Battery Hardware Simulator, Kian N. Orang, Marcelo Garcia

Electrical Engineering

This project aims to develop a battery hardware simulator, which will serve as a tool for studying microgrids. The primary objective is to create a simulation system that can emulate various battery technologies that are used in microgrids, including lithium-ion and lead acid. By utilizing this battery simulator, Cal Poly students can safely test battery management systems and battery-sensitive electronics without the inherent risks associated with real batteries. Our project implemented this design with a 4-quadrant programmable power supply (ITECH) connected to an AP Systems grid tied inverter. The power supply acts as the battery which can receive or supply …

Technical And Economic Feasibility Of A Microgrid For A Fire Station In Humboldt County, California., Nishaant Kumar Sinha

Cal Poly Humboldt theses and projects

Microgrids are emerging as a promising solution to unreliable grid energy. Today, California is not only witnessing grid resiliency challenges from natural disasters such as wildfires, earthquakes, floods and heatwaves, but it is also seeking to green the grid and bring more renewables online. For example, Humboldt County, where this project is focused, has recently experienced an earthquake of 6.4M (on December 22nd, 2022), which shut down the regional grid for ~20 hours.

Microgrid adoption enables critical facilities to operate seamlessly. The Humboldt Bay Fire Station (HBFS) No.1 is one such example, where first responders work to protect citizens against …

Which Factor Dominates Battery Performance: Metal Ion Solvation Structure-Derived Interfacial Behavior Or Solid Electrolyte Interphase Layer?, Hao-Ran Cheng, Zheng Ma, Ying-Jun Guo, Chun-Sheng Sun, Qian Li, Jun Ming

Journal of Electrochemistry

Solid-electrolyte interphase (SEI) layer formed on the electrode by electrolyte decomposition has been considered to be one of the most important factors affecting the battery performance. We discover that the metal ion solvation structure can also influence the performance, particularly, it can elucidate many phenomena that the SEI cannot. In this review, we summarize the importance of the metal ion solvation structure and the derived metal ion de-solvation behaviors, by which we can build an interfacial model to show the relationship between the interfacial behavior and electrode performance, and then apply to different electrode and battery systems. We emphasize the …

New Solid Polymer Electrolytes For Lithium, Sodium, And Calcium-Based Batteries, Francielli Silva Genier

Dissertations - ALL

The establishment of sustainable energy sources highly depends on efficient storage devices to guarantee a consistent power supply. The growing demand for lithium-ion batteries (LIBs) for this purpose, combined with concerns about lithium availability, has motivated the search for viable storage alternatives, such as sodium and calcium. While several studies have investigated different lithium-free liquid electrolytes, the transport of these alternative ions in their polymer counterparts remains understudied. The advantages of solid polymer electrolytes include the possibility of higher energy density in solid-state devices and the elimination of safety concerns associated with liquid electrolytes, such as flammability, leakage, and dendrite …

Parameter Estimation And Charge Control In Standalone And Grid-Tied Batteries, Asadullah Khalid

FIU Electronic Theses and Dissertations

Energy storage systems are the critical components enabling an electrified future ranging from electric vehicles (EVs) to microgrid (MG) applications. With the advancements in these applications, the operational dynamics of electrochemical energy storage such as Lithium-ion batteries need to be analyzed from the lifecycle impact, cybersecurity, balancing requirements, and prognostics perspectives. These operations enable the interconnected systems to be secure, efficient, and self-adaptive while reducing greenhouse emissions.

This research aims to develop threefold solutions. The first objective of this dissertation is to analyze lifecycle impact, quantify the interconnection requirements of battery energy storage systems, and evaluate cybersecurity frameworks for battery …

Nitro Group Reduction For Use In Organic, Cathodic Materials, Brock G. Goeden

Honors Thesis

The industrial demand for higher capacity, light-weight battery materials has skyrocketed in recent years due to heavy investments in portable electronics, electronic vehicles, and renewable energy sources. However, rechargeable battery technology has seen little improvement since the invention of the Lithium-Ion battery in the 1980s. The low energy density of the traditionally utilized LiCoO2 cathodic material (specific capacity: 272 mAh g-1), has limited its potential to meet these increasing demands. To solve this problem, our research group is investigating new types of lightweight, organic, polymeric materials with conductive backbones as a possible replacement for the cathodic materials in Lithium-Ion batteries. …

The Use Of Supercapacitors To Stabilize The Power Supply System Of The Base Station Of Mobile Communication, Dilmurod Abdujalilovich Davronbekov, Utkir Karimovich Matyokubov

Scientific-technical journal

In this study, an analysis of the current status and available outages of the mobile communication base station power supply system was performed. The effects of these outages on the power supply system have been studied and it has been shown that batteries may not be an ideal solution as a backup source. Also, the issue of the introduction of renewable energy sources in the base station power supply system of the mobile communication system and its shortcomings are mentioned. In order to overcome these problems and stabilize the power changes in the battery auxiliary element and the power supply …

The Use Of Supercapacitors To Stabilize The Power Supply System Of The Base Station Of Mobile Communication, Dilmurod Abdujalilovich Davronbekov, Utkir Karimovich Matyokubov

Scientific-technical journal

In this study, an analysis of the current status and available outages of the mobile communication base station power supply system was performed. The effects of these outages on the power supply system have been studied and it has been shown that batteries may not be an ideal solution as a backup source. Also, the issue of the introduction of renewable energy sources in the base station power supply system of the mobile communication system and its shortcomings are mentioned. In order to overcome these problems and stabilize the power changes in the battery auxiliary element and the power supply …

Transmission-Level Impact Analysis Of Utility-Scale Solar Photovoltaic Systems And Battery Energy Storage Grid Support, Gerald W. Bankes Ii

Theses and Dissertations--Electrical and Computer Engineering

Solar photovoltaic energy generation is expected to grow dramatically in coming years in order to take advantage of renewable and clean sources of electricity. This thesis presents research on the impact of increasing solar PV penetration, specifically of large, utility-scale PV facilities, on transmission network performance. The development of Python programming tools for automation of power flow analysis is presented. A modified version of the IEEE 118-Bus test system is developed and modified to simulate increasing PV generation on the transmission system. The impacts on performance are analyzed trends are reported. Battery energy storage systems are studied in this thesis …

The Design And Analysis Of Large Solar Pv Farm Configurations With Dc Connected Battery Systems, Oluwaseun M. Akeyo, Vandana Rallabandi, Nicholas Jewell, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Typically, solar inverters curtail or “clip” the available power from the PV system when it exceeds the maximum ac capacity. This paper discusses a battery system connected to the dc-link of an inverter to recuperate this PV energy. Contrary to conventional approaches, which employ two dc-dc converters, one each for the battery and solar PV system, the proposed configuration utilizes a single dc-dc converter capable of simultaneously operating as a charge controller and a maximum power point tracking (MPPT) tracking device. In addition to improving the overall system capacity factor, increasing the conversion efficiencies and ensuring MPPT stability, the proposed …

Passive And Active Battery Balancing Methods Implemented On Second Use Lithium-Ion Batteries, Walter Bartek

Masters Theses

As the number of electric vehicles (EVs) increases, the number of used battery packs that require disposal increases; however, many of these packs still have useful capacity and can be repurposed. When using repurposed large lithium-ion battery packs, deviations between cells within a pack become problematic. These deviations result in a pack that is unbalanced, affecting performance and proving potentially hazardous when charging. Consequently, a battery management system (BMS) is needed. To provide safety, the BMS in this paper monitors and controls the operation of the battery pack. In addition, it controls the redistribution of charge between the cells within …

Integration Of Large Pv Power Plants And Batteries In The Electric Power System, Oluwaseun M. Akeyo

Theses and Dissertations--Electrical and Computer Engineering

The declining cost of renewables, the need for cleaner sources of energy, and environmental protection policies have led to the growing penetration of inverter-based resources such as solar photovoltaics (PV), wind, and battery energy storage systems (BESS) into the electric power system. The intermittent nature of these resources poses multiple challenges to the power grid and substantial changes in the conventional generation and electrical power delivery practices will be required to accommodate the large penetration of these renewable power plants. The impact of large solar PV penetration on both generation and transmission systems, and the use of BESS to mitigate …

Software-Defined Infrastructure For Iot-Based Energy Systems, Stephen Lee

Doctoral Dissertations

Internet of Things (IoT) devices are becoming an essential part of our everyday lives. These physical devices are connected to the internet and can measure or control the environment around us. Further, IoT devices are increasingly being used to monitor buildings, farms, health, and transportation. As these connected devices become more pervasive, these devices will generate vast amounts of data that can be used to gain insights and build intelligence into the system. At the same time, large-scale deployment of these devices will raise new challenges in efficiently managing and controlling them. In this thesis, I argue that the IoT …

Measurement And Estimation Of The Equivalent Circuit Parameters For Multi-Mw Battery Systems, Oluwaseun M. Akeyo, Vandana Rallabandi, Nicholas Jewell, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

This paper proposes and validates through simulations and measurements, a procedure for the determining the equivalent circuit parameters of large utility-scale batteries. It is considered that a large battery includes multiple cells connected in series and parallel, and therefore, its equivalent circuit can be represented as a series-parallel network of state of charge (SOC) dependent resistors and capacitors. Tests for determining these equivalent circuit parameters are proposed. These tests involve subjecting the battery energy storage system (BESS) to multiple charge and discharge cycles, while monitoring the terminal voltage and current response. A method for post-processing and analyzing the measurements in …

Modeling And Simulation Of A Utility-Scale Battery Energy Storage System, Oluwaseun M. Akeyo, Vandana Rallabandi, Nicholas Jewell, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

This paper presents the modeling and simulation study of a utility-scale MW level Li-ion based battery energy storage system (BESS). A runtime equivalent circuit model, including the terminal voltage variation as a function of the state of charge and current, connected to a bidirectional power conversion system (PCS), was developed based on measurements from an operational utility-scale battery demonstrator. The accelerated response of the battery unit was verified by pulse discharging it from maximum to minimum SOC and its application for grid resiliency was demonstrated through an example droop control frequency response. For the purpose of validating the equivalent BESS …

Optimization Of Pv Powered Spd Switchable Glazing To Minimise Probability Of Loss Of Power Supply, Aritra Ghosh, Brian Norton

Articles

Suspended particle device (SPD) glazing is an electrically actuated switchable glazing. It requires alternate current (AC) power supply to switch from opaque to transparent state. To power this glazing using PV device requires inverter. Optimization of AC powered switchable SPD glazing using photovoltaic (PV) device has been evaluated using loss of power supply probability (LPSP). Electrically switchable direct current (DC) powered electrochromic glazing was also considered in this investigation as it doesn't need any inverter to couple with PV. It is concluded that behaviour of these glazings is the dominant factor in performance optimization outweighting than azimuthal orientation and inclination …

Incorporating Battery Energy Storage Systems Into Multi-Mw Grid Connected Pv Systems, Vandana Rallabandi, Oluwaseun M. Akeyo, Nicholas Jewell, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

This paper analyzes the configuration, design, and operation of multi-MW grid connected solar photovoltaic (PV) systems with practical test cases provided by a 10-MW field development. In order to improve the capacity factor, the PV system operates at its maximum power point during periods of lower irradiance, and the power output is limited to a rated value at high irradiance. The proposed configuration also incorporates a utility scale battery energy storage system (BESS) connected to the grid through an independent inverter and benefits of the experience gained with a 1-MW 2-MWh BESS large demonstrator. The BESS power smoothing and frequency …

A Sustainable Prototype For Renewable Energy: Optimized Prime-Power Generator Solar Array Replacement, Nathan Thomsen, Torrey J. Wagner, Andrew J. Hoisington, Steven J. Schuldt

Faculty Publications

Remote locations such as disaster relief camps, isolated arctic communities, and military forward operating bases are disconnected from traditional power grids forcing them to rely on diesel generators with a total installed capacity of 10,000 MW worldwide. The generators require a constant resupply of fuel, resulting in increased operating costs, negative environmental impacts, and challenging fuel logistics. To enhance remote site sustainability, planners can develop stand-alone photovoltaic-battery systems to replace existing prime power generators. This paper presents the development of a novel cost-performance model capable of optimizing solar array and Li-ion battery storage size by generating tradeoffs between minimizing initial …

Power Utility Tests For Multi-Mw High Energy Batteries, Oluwaseun M. Akeyo, Huangjie Gong, Vandana Rallabandi, Nicholas Jewell, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

This paper reviews the procedures, layouts and metrics described in the new test manual issued by the Electric Power Research Institute (EPRI), in order to determine the performance and functionality of a utility scale battery energy storage system (BESS). In this approach, the large battery unit is connected to the dc-link of a bidirectional power conversion system (PCS), which may be interfaced with either the utility grid or a load bank for the purpose of estimating the BESS operation and performance characteristics, some of which includes; available charge/discharge energy at rated power, continuous charge/discharge duration, battery ramp rate, and ac …

Improving The Capacity Factor And Stability Of Multi-Mw Grid Connected Pv Systems With Results From A 1mw/2mwh Battery Demonstrator, Oluwaseun M. Akeyo, Vandana Rallabandi, Nicholas Jewell, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Conventional PV systems integrated with a battery connect the array and the energy storage unit to a dc-link through individual dc-dc converters for maximum power point tracking (MPPT) and battery charge control. This paper proposes a new system configuration, which connects the PV array and battery unit to the dc-link of the system inverter via a single dc-dc converter capable of simultaneously operating as a charge controller and MPPT device. This dc-dc converter is controlled such that it charges/discharges the battery with the amount of power required to maintain the PV array at its MPPT reference voltage. The proposed system …

Analysis Of The Properties Of Supercapacitors And Possible Applications For The Technology, Vincent Oliveto

Honors Theses

Supercapacitors have a lot of excellent qualities that would make them a great substitute for batteries when it comes to electrical energy storage systems. Supercapacitors can discharge and charge very rapidly, they have a lifespan in the realm of millions of cycles, and they are much more efficient than batteries. Unfortunately, they cannot hold nearly as much charge as batteries. This paper seeks to further investigate the properties of supercapacitor technology and the best way to exploit these properties with the purpose of integrating them into renewable energy systems. There is currently a lot of research occurring around the world …

Novel Technique Of Fabrication Of Porous Copper And Copper Oxide To Improve The Lithium Ion Battery Performance, Raju Prasad Ghimire

Electronic Theses and Dissertations

Due to widespread and long-term application, Lithium-ion batteries are considered as promising power sources for portable devices, satellites, medical instruments, computers, electric vehicles and grid application. It started to occupy the market once Sony commercialized in 1991. Rechargeable lithium ion batteries drawing people attention due to their peculiar properties such as high energy density and low self-discharge compared to other alkali metals. However, these widespread and long-term applications still require better batteries in terms of performance, safety and cost, which can be achieved by better utilization of anode materials and/or an optimized design of battery configuration. There are several challenges …

Dc-To-Dc Buck Converter, Kyle Christopher Roman

Electrical Engineering

The growth of sustainable energy requires many components to work in harmony creating one efficient and effective system. Sustainable energy generation that produces a DC current varying in voltage requires a subsystem to convert voltage to a practical and usable value. The DC to DC Buck converter converts high DC solar generated voltage to a 12V output. This Modular -Level power electronic (MLPE) device performs as a solar charge controller for small lithium ion batteries. Fluctuating voltage levels generated by Photovoltaic cells makes the solar controller a critical part of the solar system. Regulating the DC voltage allows safe and …

Multi-Mw Solar Pv Pumping System With Capacity Modulation And Battery Voltage Support, Oluwaseun M. Akeyo, Vandana Rallabandi, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Solar photovoltaic (PV) renewable energy systems are undergoing major technological developments and large-scale field deployment and electric grid integration. This paper proposes a method of expanding the capacity of an existing irrigation farm with additional pumps powered by solar PV. The system includes PV arrays and battery energy storage connected to a common dc bus, which energizes an array of variable speed inverter driven pumps. Capacity modulation is achieved by energizing an optimal number of pumps required in order to meet a particular load demand with minimum supply energy. A grid connection to the dc bus of the power electronic …

Battery Energy Storage Emulation For Power System Applications, Jessica Danielle Boles

Masters Theses

The concept of energy storage for power systems has received increasingly more attention in recent decades, and the growing penetration of renewable energy sources has only escalated demand for it. Energy storage systems are excellent for balancing generation and load, for suppressing power fluctuations, and for providing other ancillary services to the grid. The Hardware Testbed (HTB) is a novel converter-based grid emulator created for studying the needs associated with high renewable penetration, but the system currently lacks a battery storage emulator. Thus, this work documents the development of a battery energy storage system (BESS) emulator for the HTB.

The …

Solar Roller - Solar Powered Usb Charging Station, Aaron Bartfeld, Tanner Mjelde, Kaylan Naicker

Electrical Engineering

As the necessity for renewable energy increases, solar power becomes more and more prevalent. At the same time, as technology increases, the necessity for charging one’s electronic devices also increases. The Solar Roller merges solar energy with the ability to charge one's electronic device in one compact cart. The Solar Roller is a solar-powered USB charging station that allows people of all backgrounds to develop a better understanding of alternative fuels, while charging their USB device. It has a touch screen display that provides voltage levels of the battery as well as a TV that displays solar powered information. The …

Analysis And Simulation Of Photovoltaic Systems Incorporating Battery Energy Storage, Oluwaseun M. Akeyo

Theses and Dissertations--Electrical and Computer Engineering

Solar energy is an abundant renewable source, which is expected to play an increasing role in the grid's future infrastructure for distributed generation. The research described in the thesis focuses on the analysis of integrating multi-megawatt photovoltaics (PV) systems with battery energy storage into the existing grid and on the theory supporting the electrical operation of components and systems. The PV system is divided into several sections, each having its own DC-DC converter for maximum power point tracking and a two-level grid connected inverter with different control strategies. The functions of the battery are explored by connecting it to the …

Property Analysis Of Silylamine Type Reversible Ionic Liquids For Use As A Thermal Safety Switch In Batteries, Showmik Podder

Dissertations and Theses

The increased capacity of the modern battery system has also brought about safety apprehensions. Uncontrollable runaway reactions are a big concern in these systems; these reactions are the result of in situ heat generation and very much increase the risk of explosions and device failures. The concept of this work is to provide a preliminary understanding into the use of a type of switchable solvent known as reversible ionic liquids (RevILs) and their feasibility in being used in electrolytes as a thermally-controlled reversible safety switch. In their pure forms these switchable solvents experience a dramatic change in their properties upon …

Hybrid Energy Storage Implementation In Dc And Ac Power System For Efficiency, Power Quality And Reliability Improvements, Mustafa Farhadi

FIU Electronic Theses and Dissertations

Battery storage devices have been widely utilized for different applications. However, for high power applications, battery storage systems come with several challenges, such as the thermal issue, low power density, low life span and high cost. Compared with batteries, supercapacitors have a lower energy density but their power density is very high, and they offer higher cyclic life and efficiency even during fast charge and discharge processes. In this dissertation, new techniques for the control and energy management of the hybrid battery-supercapacitor storage system are developed to improve the performance of the system in terms of efficiency, power quality and …

Universal Programmable Battery Charger With Optional Battery Management System, Michael Duke Desando

Master's Theses

This report demonstrates improvements made in battery charging and battery management technology through the design of a universal programmable battery charger with optional battery management system attachment. This charger offers improvements in charge efficiency and unique battery charging algorithms to charge a variety of battery chemistries with variety of power requirements. Improvements in efficiency result from a synchronous Buck Controller topology as compared to previous universal chargers that use asynchronous Buck-Boost Converter topologies. This battery charger also surpasses current universal battery chargers by offering different charge modes for different battery chemistries. Charge modes provide the user an option between extending …