Power and Energy Commons^™

Time-Varying Harmonic Analyzer Prototype, Diego F. Fabri, Carlos H. N. Martins, Leandro R. M. Silva, Carlos A. Duque

University Faculty Publications and Creative Works

This paper presents a time-varying harmonic analyzer based on the Sliding Window DFT implemented on a DSP platform. The harmonic decomposition is carried out using the TMS320F28027 digital signal processor, and the samples of the decomposed signal are sent to a PC based computer using serial interface. Several real cases are analyzed, revealing the time-varying behavior of the harmonic component. Different from commercial harmonic analyzer, the prototype presented in this paper uses a different way to visualize the harmonic components, based on time decomposition approach. This new visualization of time-varying harmonics might help engineers and researchers to develop new insights …

Time-Varying Harmonic Analyzer Prototype, Diego F. Fabri, Carlos H. N. Martins, Leandro R. M. Silva, Carlos A. Duque

University Faculty Publications and Creative Works

This paper presents a time-varying harmonic analyzer based on the Sliding Window DFT implemented on a DSP platform. The harmonic decomposition is carried out using the TMS320F28027 digital signal processor, and the samples of the decomposed signal are sent to a PC based computer using serial interface. Several real cases are analyzed, revealing the time-varying behavior of the harmonic component. Different from commercial harmonic analyzer, the prototype presented in this paper uses a different way to visualize the harmonic components, based on time decomposition approach. This new visualization of time-varying harmonics might help engineers and researchers to develop new insights …

Optimization Design Of Electrodes For Anode-Supported Solid Oxide Fuel Cells Via Genetic Algorithm, Junxiang Shi, Xingjian Xue

Faculty Publications

Porous electrode is the critical component of solid-oxide fuel cells (SOFCs) and provides a functional material backbone for multi-physicochemical processes. Model based electrode designs could significantly improve SOFC performance. This task is usually performed via parameter studies for simple case and assumed property distributions for graded electrodes. When nonlinearly coupled multiparameters of electrodes are considered, it could be very difficult for the model based parameter study method to effectively and systematically search the design space. In this research, the optimization approach with a genetic algorithm is demonstrated for this purpose. An anode-supported proton conducting SOFC integrated with a fuel supply …

Adaptive Voltage Control Methods Using Distributed Energy Resources, Huijuan Li

Doctoral Dissertations

Distributed energy resources (DE) with power electronics interfaces and logic control using local measurements are capable of providing reactive power related to ancillary system services. In particular, local voltage regulation has drawn much attention in regards to power system reliability and voltage stability, especially from past major cascading outages. This dissertation addresses the challenges of controlling the DEs to regulate the local voltage in distribution systems.

First, an adaptive voltage control method has been proposed to dynamically modify the control parameters of a single DE to respond to system changes such that the ideal response can be achieved. Theoretical analysis …

Multi-Modular Integral Pressurized Water Reactor Control And Operational Reconfiguration For A Flow Control Loop, Sergio Ricardo Pereira Perillo

Doctoral Dissertations

This dissertation focused on the IRIS design since this will likely be one of the designs of choice for future deployment in the U.S and developing countries. With a net 335 MWe output IRIS novel design falls in the “medium” size category and it is a potential candidate for the so called modular reactors, which may be appropriate for base load electricity generation, especially in regions with smaller electricity grids, but especially well suited for more specialized non-electrical energy applications such as district heating and process steam for desalination. The first objective of this dissertation is to evaluate and quantify …

Optimal Allocation Of Tcsc Devices Using Genetic Algorithms, Almoataz Youssef Abdelaziz

Almoataz Youssef Abdelaziz

This paper presents an approach to find the optimal location of thyristor-controlled series compensators (TCSC) in a power system to improve the loadability of its lines and minimize its total loss. Also the proposed approach aims to find the optimal number of devices and their optimal ratings by using genetic algorithm (GA) with taking into consideration the thermal and voltage limits. Examination of the proposed approach is carried out on the IEEE 9-bus system.

A Classification Technique For Protection Coordination Assessment Of Distribution Systems With Distributed Generation, Almoataz Youssef Abdelaziz

Almoataz Youssef Abdelaziz

In this paper a novel approach is presented to study the impact of distributed generation on recloser-fuse coordination. This approach is based on the assessment of the recloser-fuse coordination due to the penetration of distributed generation with specified location and capacity for a given fault location. This assessment process acts as a classifier, based on finding the operating sequence of all reclosers and fuses in the path from the faulted node to the substation. This sequence is compared with a pre-required sequence obtained from the protection coordination philosophy, and then provides the distribution system operator with a result indicating whether …

Optimal Tuning Of Power System Stabilizers Using Modified Particle Swarm Optimization, Mahdiyeh Eslami, Hussain Shareef, Azah Mohamed

Dr. Mahdiyeh Eslami (مهدیه اسلامی)

No abstract provided.

Improved Particle Swarm Optimization With Disturbance Term For Multi-Machine Power System Stabilizer Design, Mahdiyeh Eslami, Hussain Shareef, Azah Mohamed, Mohammad Khajehzadeh

Dr. Mahdiyeh Eslami (مهدیه اسلامی)

No abstract provided.

Tuning Of Power System Stabilizers Using Particle Swarm Optimization With Passive Congregation, Mahdiyeh Eslami, Hussain Shareef, Azah Mohamed, S. P Ghoshal

Dr. Mahdiyeh Eslami (مهدیه اسلامی)

No abstract provided.

Control Of A High-Performance Z-Source Inverter For Fuel Cell/Supercapacitor Hybrid Electric Vehicles, Omar Ellabban, Joeri Van Mierlo, Philippe Lataire

Omar Ellabban

This paper presents a supercapacitor (SC) module connected in parallel with fuel cell (FC) stack to supply a high-performance Z-Source Inverter (HP-ZSI) feeding a three phase induction motor for hybrid electric vehicles applications. The supercapacitor is connected between the input diode and the bidirectional switch of the highperformance ZSI topology. The indirect field-oriented control (IFOC) method is used to control an induction motor speed during motoring and regenerative braking operations to produce the modulation index and a dual loop controller is used to control the Z-network capacitor voltage to produce the shoot-through duty ratio. MATLAB simulation results verified the validity …

Model-Based Analysis Of Electric Drive Options For Medium-Duty Parcel Delivery Vehicles, Robb A. Barnitt, Aaron D. Brooker, Laurie Ramroth

Publications (T)

Medium-duty vehicles are used in a broad array of fleet applications, including parcel delivery. These vehicles are excellent candidates for electric drive applications due to their transient-intensive duty cycles, operation in densely populated areas, and relatively high fuel consumption and emissions. The National Renewable Energy Laboratory (NREL) conducted a robust assessment of parcel delivery routes and completed a model-based techno-economic analysis of hybrid electric vehicle (HEV) and plug-in hybrid electric vehicle (PHEV) configurations. First, NREL characterized parcel delivery vehicle usage patterns, most notably daily distance driven and drive-cycle intensity. Second, drive-cycle analysis results framed the selection of drive cycles used …

Effect Of Impurities On Performance Of Proton Exchange Membrane Fuel Cell Components, Kitiya Hongsirikarn

All Dissertations

It is believed that proton–exchange membrane fuel cells (PEMFCs) are going to be exploited as power generation devices for stationary, automotive, and portable applications in the near future because of their high performance and environmental friendliness. Up to the present, wide spread utilization of PEMFCs is not viable because of their cost and durability in the presence of fuel and oxidant stream impurities. These impurities include NH₃, hydrocarbons, CO, CO₂, halogenated compounds, cations, etc. The objective of this research was to investigate the effect of these harmful contaminants containing in the H₂ fuel stream on …

The Generation Of Domestic Electricity Load Profiles Through Markov Chain Modelling, Fintan Mcloughlin, Aidan Duffy, Michael Conlon

Articles

Micro-generation technologies such as photovoltaics and micro-wind power are becoming increasing popular among homeowners, mainly a result of policy support mechanisms helping to improve cost competiveness as compared to traditional fossil fuel generation. National government strategies to reduce electricity demand generated from fossil fuels and to meet European Union 20/20/20 targets is driving this change. However, the real performance of these technologies in a domestic setting is not often known as high time resolution models for domestic electricity load profiles are not readily available. As a result, projections in terms of reducing electricity demand and financial paybacks for these micro-generation …

Concept For Next Generation Phasor Measurement: A Low-Cost, Self-Contained, And Wireless Design, Brian Ray Miller

Masters Theses

Phasor measurement is a growth technology in the power grid industry. With new funding, grid reliability concerns, and power capacity margin motivating a smart grid transformation, phasor measurement and smart metering are taking center stage as the implementation methods for grid intelligence. This thesis proposes a novel concept for designing a next generation phasor measurement unit.

The present generation phasor measurement unit relies upon venerable existing current and voltage transducer technology that is expensive, bulky, and not well suited to the modern age of digital and computerized control signals. Also, the rising proliferation of installed phasor measurement units will soon …

Effects Of Cloud-Induced Photovoltaic Power Transients On Power System Protection, Joel A. Nelson

Master's Theses

As the world strives towards finding alternative sources of power generation, photovoltaic generation has become an increasingly prevalent alternative energy source on power systems world-wide. This paper studies the effects that incorporating photovoltaic generation has on the existing power systems and their power system protection schemes. Along with the addition of this emerging alternative energy source comes the volatility of PV power generation as cloud-cover produces erratic variations in solar irradiance and PV power production. Such variations in PV power may lead to unfavorable operating conditions and power system failures. The issues addressed in this paper include a study of …

Energy Efficient Led Displays, John Mani Kumar Jupalli

UNLV Theses, Dissertations, Professional Papers, and Capstones

In this research work, an innovative pixel architecture RGBW, consisting of red (R), green (G), blue (B), and white (W) LEDs, is designed and implemented for color generation. Energy consumption of new pixel architecture consisting of RGBW LEDs is compared to standard architecture consisting of RGB LEDs. Human perception experiments are conducted to study the differences in perception between the two architectures when the same colors are generated using RGBW vs. RGB. Measurements of power for a 32inch x 16inch LED display has proved up to 18% power savings for low saturated colors, up to 8% for high saturated colors …

Research On Nafion/Sio_2 Composite Membrane In All Vanadium Redox Flow Battery, Dong-Dong Liu, Mao-Cai Lin, Tao Guan, Qing-Chun Yu

Journal of Electrochemistry

The Nafion117/SiO2 composite membrane was prepared by sol-gel method.The results showed that,during composite membrane preparation process,the ratio of MeOH and TEOS did not affect the penetration rate of VO2+ basically,however,the lowest permeability of 427×10-9cm2/s in the membrane was achieved while hydrolysis time was 10 min and natural drying for 24 h after hydrolysis,which reduced by 52 times than that in Nafion117 membrane.The SEM tests proved that SiO2 grains grew bigger in the composite membrane during the natural drying,and most of the holes in Nafion117 were filled.Single cell test showed the battery power efficiency was improved by 2.7 %.

Electrodeposition Of Lead Dioxide From Dluoroborate Solutions, Chun-Mei Kong, Yong-Ming Tang, Wen-Zhong Yang, Xiao-Yuan Yang

Journal of Electrochemistry

The PbO2 anodes were prepared on platinum from fluoroborate media and its doped solutions by electrodeposition technique.Elecchemical and pysicochemical properties of these PbO2 films were studied by cyclic voltammetry methods,XRD and SEM.The results showed that the presence of BF4-increased PbO2 electrodeposition rate;the prepared lead dioxide consisted of β-PbO2;the preferential orientation of crystals and surface morphology were affected a lot by doping F-and Fe3+.The FB/F-Fe-PbO2 electrode exhibited regular-shaped layers with compact morphology.Furthermore,increasing current density also change the preferential orientation of PbO2 crystals.

Effects Of Solvents And Electrolyte Salts On The Electrochemical Reduction Of Oxygen In Non-Aqueous Electrolytes, Yan-Yan Tian, Wei Wu, Jun Gao, Yong Yang

Journal of Electrochemistry

The electrochemical reduction processes of oxygen in different non-aqueous solvents such as acetonitrile(MeCN),propylene carbonate(PC) and their mixtures were investigated by cyclic voltammetry method.The results indicated a one electron reduction of oxygen to O2-occured in these systems as a first step reduction,no matter whether in tetrabutylammonium hexafluorophosphate(TBAPF6)/MeCN or TBAPF6/PC electrolyte.However,the CV curves in 0.1 mol·L-1 TBAPF6/MeCN showed a couple of reversible redox peaks,indicating that the reduction process of oxygen was irreversible in the 0.1 mol·L-1 TBAPF6/PC electrolyte.In the PC-based electrolyte,the reduction current peak reduced largely and the oxidation peak of O2-almost disappeared as compared to that of the former electrolytes.The possible …

Photoelectrochemical Properties Of N,S,And Cl Modified Nano Tio_2 Thin Films, Hong Yun, Chang-Jian Lin, Jing Li, Rong-Gui Du

Journal of Electrochemistry

The nitrogen(N),sulfur(S) and chlorine(Cl) modified nano TiO2 thin films were prepared by adding Ti(O-n-Bu)4 as the precursor into concentrated HNO3,H2SO4 and HCl Solutions,respectively,on different substrates in a sol-gel process.The photoelectrochemical performances of N,S and Cl modified nano TiO2 thin films have been studied by UV-vis(DRS),photocurrent curves,EIS and OCP-time curves.N-modified TiO2 nano films show better surface structure,which helps to improve the quantum efficiency of nano TiO2 thin films.

Hydrothermal Reduction Synthesis Of Lifepo_4 And Its Electrochemical Performance, Hong-Li Zou, Guang-Hui Zhang, Pei-Kang Shen

Journal of Electrochemistry

The cathode materials of LiFePO4 were prepared via a hydrothermal reduction method using FeCl3 as Fe source and iron as a reducing agent.The results showed that ferric salt could be reduced to ferrous salt completely under the hydrothermal condition and pure-phase LiFePO4 was obtained based on the test results of XRD and FTIR.Carbon-coated LiFePO4 was synthesized by pyrolysisng glucose at high temperature.The morphologies of pure LiFePO4 displayed cluster-like while the LiFePO4/C displayed sphere-like particles.The electrochemical test showed that the LiFePO4/C had good rate performance,while LiFePO4 delivered much lower discharge capacity.

The Sol-Gel Synthesis And Electrochemical Performance Of Li_3v_2(Po_4)_3/C Cathode Material For Lithium Ion Battery, Li-Ying Liu, Lian Chen, Hai-Yan Zhang, Yu-Chun Zhai

Journal of Electrochemistry

Li3V2(PO4)3/C was synthesized by sol-gel method with citric acid as chelate and C sources.Physical and electrochemical performances of as-prepared materials were characterized through XRD,SEM and galvanostatic charge-discharge tests,etc.The results showed that products produced by calcining at 800 ℃ for 12 h had a single phase crystal structure and relatively small particle sizes with uniform distribution.At 0.1 C,0.5 C and 1 C,the initial specific discharge capacities were 153.0,143.1 and 130.6 mAh·g-1,respectively,and capacity efficiencies were 93.1%,85.4% and 77.3% after 50 cycles,respectively.Charge efficiencies were all above 80% and discharge voltages were higher.

A Neural Network Based Speed Control Of A Linear Induction Motor Drive, Adel A. Elbaset, Ahmed A. Hassan, Yehia S. Mohamed, T. Hiyama,, T. H. Mohamed

Dr. Adel A. Elbaset

In this paper, a general regression neural network (GRNN) based controller is used to control the speed and thrust output of the linear induction motor drive. The field orientation principle is used to asymptotically decouple the motor speed from the secondary flux. The idea of model predictive control technique is used for the training of the proposed controller. The motivation for using this control strategy for training the GRNN based controller is to reduce the effect of the uncertainty due to motor parameters variation and load disturbance. This newly developed design strategy combines the advantage of the neural networks and …

Energy Storage And Management For A Small Series Plug-In Hybrid Electric Vehicle, Liqin Ni

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Plug-in hybrid electric vehicles (PHEVs) are gaining increasing interest for both residential and commercial transportation applications. In PHEV design, energy storage system (EES) is a critical component which will impact the overall design efficiency, performance, cost and etc. This dissertation aims to design an advanced energy storage system for a small plug-in hybrid electric vehicle, whose performance will approach very closely to the optimal possible, in terms of energy efficiency and acceleration, for passenger road vehicles application. Moreover, practical automotive requirements are considered during ESS design, such as cost, life time, safety and volume.

This dissertation utilizes ultracapacitors in conjunction …

Gas Turbine, Vijaya Krushna Varma Mr

VIJAYA KRUSHNA VARMA Mr

Varma designed ultra modern and high efficiency turbines which can use gas, steam or fuels as feed to produce electricity or mechanical work for wide range of usages and applications in industries or at work sites. Varma turbine engines can be used in all types of vehicles. These turbines can also be used in aircraft, ships, battle tanks, dredgers, mining equipment, earth moving machines etc, Salient features of Varma Turbines. 1. Varma turbines are simple in design, easy to manufacture, easy to operate and maintain. 2. Varma turbines are less expensive. 3. Varma turbines have a great power to weight …

Water Turbine, Vijaya Krushna Varma Mr

VIJAYA KRUSHNA VARMA Mr

Varma designed ultra modern and high efficiency turbines which can use gas, steam or fuels as feed to produce electricity or mechanical work for wide range of usages and applications in industries or at work sites. Varma turbine engines can be used in all types of vehicles. These turbines can also be used in aircraft, ships, battle tanks, dredgers, mining equipment, earth moving machines etc, Salient features of Varma Turbines. 1. Varma turbines are simple in design, easy to manufacture, easy to operate and maintain. 2. Varma turbines are less expensive. 3. Varma turbines have a great power to weight …

Designing A Photovoltaic System Hybrid For A Health Clinic In Camilo Ortega, Nicaragua, Jeremy Holliman

Electrical Engineering

As developing nations continue to foster the development of their technologies and economies, industrialized nations have taken an active approach in providing green and sustainable alternatives for them to consider. Non-profit organizations like Engineers Without Borders holds sustainable international development as paramount to all international projects that their student and professional chapters undertake. The Cal Poly Engineers Without Borders student chapter has implemented a variety of projects from slow sand filters to compressed earth blocks, and the Nicaragua team is in the process of designing a health clinic for the Camilo Ortega community. In order to power the health clinic, …

The Impact Of Quality Management Systems During A Pebble Bed Modular Reactor Project : A Case Study, Lwandiso Zamxaka

Lwandiso L Zamxaka

In the nuclear industry, Quality Management Systems are extremely important,especially if one wishes to improve public acceptance of radioactive solutions.There is normally minimum communication between the public and scientists,especially in nuclear science. People are not comfortable with nuclear technology,based on the past history of the Chernobyl catastrophe. Consequently, it is difficult to discuss important and sensitive issues like disposing of nuclear waste. Quality Management Systems can improve public confidence and communication. Integrated Management Systems in the project planning stage of the project can be a proactive step towards preventing unnecessary delays and costs. There is a perception that quality is …

Genetic Algorithm Based Optim-Al Sizing Of Pv-Diesel-Battery System Considering Co2 Emission And Reliability, Dr. Adel A. Elbaset, Heri Suryoatmojo, Prof. Dr. Takashi Hiyama

Dr. Adel A. Elbaset

The reliability system concern and CO2 emission reduction are still the main targets of optimization problem in the hybrid generation system components. This pa- per utilizes Genetic Algorithm (GA) method to determine the optimal capacities of PV system, battery bank and diesel generator (DG) unit according to the minimum cost ob- jective functions that relate to these two factors. In this study, the cost objective function includes the annual capital cost (ACC), annual operation maintenance cost (AOM), an- nual replacement cost (ARC), annual fuel cost (AFC), annual emission cost (AEC) and annual customer damage cost (ADC). The proposed method has …