Power and Energy Commons^™

An Investigation On Electrochemical Performance Of Supercapacitor Electrode Materials Prepared By Mno2 With Four Different Crystal Forms, Zhen-Kun Wei, Xiao-Zhen Hua, Ke Xiao, Xian-Liang Zhou, Zhi-Guo Ye

Journal of Electrochemistry

Four types of α-MnO₂, β-MnO₂, γ-MnO₂ and δ-MnO₂ powders were synthesized by relatively simple methods. The differences in crystal structures and surface morphologies for these forms of MnO₂ were investigated by using X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), thermogravimetric analysis (TGA) and specific surface area analysis (BET). The electrochemical performances were characterized by cyclic voltammetry (CV) and stability analysis. Based on the experimental results, four kinds of MnO₂ electrodes showed good capacity properties, and the α-MnO₂ electrode had the largest specific capacity due to the highest specific surface …

Effect Of Adsorption Potential On Co Oxidation At Au@Pt Nanoparticles Electrodes, A Surface Enhanced Raman Spectroscopic Study, Pu Zhang, Yi Wei, Yong-Li Zheng, Yan-Xia Chen, Zhong-Qun Tian

Journal of Electrochemistry

The adsorption/oxidation of CO on the 55 nm [email protected] nm Pt nanoparticles electrode in both potentiodynamic and potentiostatic modes were investigated by surface enhanced Raman spectroscopy in a thin layer electrochemical flow cell under controlled mass transport, with the aim of clarifying the origin CO oxidation at lower electrode potentials (in current pre-wave region of corresponding cyclic voltammograms). Our results demonstrated that the CO oxidation kinetics differed significantly from the three kinds of different CO adsorption history, with almost no CO oxidation current in the pre-peak potential region after 0.35 V_RHE CO adsorption with or without subsequent holding the …

Synthesis And Electrochemical Performance Of Mn3O4/Graphene Composites, Shan-Shan Yang, Qian Zhang, Xiong-Gui Lin, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

The Mn₃O₄/Graphene composites were synthesized by hydrothermal method with the in-situ redox reaction of graphene oxide (GO) and manganese acetate (Mn(Ac)₂). The phase structures and morphologies of the materials were characterized by XRD, SEM and TEM. The XPS and IR techniques were used for studying the residual function groups of reduced graphene oxide (RGO). The electrochemical performances of the hybrids were tested in a coin cell. Results showed that the composites prepared with the addition of ammonia water (RM-A) have better performance. The graphenes in RM-A were better-reduced and the Mn₃O_{4 …}

Tungsten Carbide/Carbon Electrode Material Synthesized By Block Copolymer Template Method, Xiao-Ling Lang, Ye-Kun Jiang, Mei-Qin Shi, Ling-Zhi Kang, Chun-An Ma

Journal of Electrochemistry

At present, one of the major hurdles for commercialization of system with direct methanol fuel cell (DMFC) is still the requirement of a significant amount of platinum (Pt) catalyst to achieve an acceptable power density. Pt and Pt-based metals are expensive due to limited supplies. In order to find the catalyst alternative to the Pt metal, we selected tungsten carbide (WC) and its composites as the study object. We synthesized WC with carbon materials as the suitable support to modify the electronic structure and to increase the specific surface area of WC. In this study, tungsten carbide/carbon (WC/C) was prepared …

Mechanism Study On The Electrocatalytic Oxidation Of Acetylene To Oxalic Acid, Xiu-Li Song, Rui-Long Jia, Wen-Yan Dong, Zhen-Hai Liang

Journal of Electrochemistry

A new method of electrocatalytic synthesis oxalic acid from acetylene was explored and the synthesized oxalic acid was characterized by Ultraviolet-visible spectrophotometry (Uv-vis) and Infrared spectroscopy (IR). First-principles calculations were carried out to examine the adsorption of acetylene over the Pt(111) surface. The electrocatalytic oxidation behavior of acetylene has been investigated on a Pt electrode by cyclic voltammetry (CV) and steady-state polarization in Na₂SO₄ solution. The formation mechanism of oxalic acid in the Na₂SO₄ solution was proposed and the transfer coefficients of the reaction were calculated. The results show that acetylene molecule tends to …

Effect Of Carbon Nanotubes On Anodic Properties Of Ti/Ru-Ir-Sn Oxides, Feng Lian, Yong-Lei Xin, Bo-Jiang Ma, Li-Kun Xu

Journal of Electrochemistry

The Ru-Ir-Sn metal oxide anodes coated on titanium (Ti/Ru-Ir-Sn) were prepared by thermal decomposition. The effects of amounts of carbon naotubes (CNTs) on anodic properties were studied by TGA, SEM, EDS, cyclic voltammetry, EIS, polarization measurements and accelerated life test. The thermogravimetric analysis and EDS spectrum data showed that the high temperature oxidation decomposition of CNTs did not take place under the condition of the sintering temperature of 470 ℃, and the CNTS still existed in the anode coating in an element form. Compared with the contrast samples, the surface crack of the coating increased, but remained typical morphology. Adding …

Reaction Mechanisms Study Of Pb Electrodes In Sulfuric Acid And Sodium Sulfate Solutions By Eqcm, Xian-Ping Zou, Zong-Xuan Kang, Yu-Lan Huang, Dong Shu, Ya-Yun Zhong, Jun-Nan Hao, Yu-Qing Liao

Journal of Electrochemistry

Surface reaction processes of Pb electrodes were investigated in H₂SO₄ and Na₂SO₄ solutions by LSV, CV and EQCM. The results in the voltammogram and the mass change curve of the Pb electrode indicated that the oxide products of lead included PbSO4 and PbO·PbSO₄ in sulfuric acid solution with a positive-going potential scan from -1.0 V to -0.4 V and then PbO·PbSO₄ transformed into PbSO₄. However, the oxide product of lead was only PbSO₄ in sodium sulfate solution. The experimental results revealed that the acid solution is necessary for the …

Research On The Application Of Solar Photovoltaic System On Large Ocean-Going Ships, Wanhe Huang

Maritime Safety & Environment Management Dissertations (Dalian)

No abstract provided.

Adaptive Online Transient Stability Assessment Of Power Systems For Operational Purposes, Hussain Hassan Al Marhoon

LSU New Orleans Theses and Dissertations

Online stability assessment is an important problem that has not been solved completely yet. The purpose of this research is to tackle online transient stability assessment. Currently, most utility companies use step-by-step integration in order to set protective equipment so that they effectively work for critical contingencies. However, there are times an unforeseen contingency may occur which may cause the system to transit and the protective equipment to misoperate and does not isolate the disturbed part of the system. This research introduces a method that automatically determines a group of generators that participate in system separation and hence transient instability. …

Wireless Power Transfer To A Small, Remote Control Boat, Mark M. Oscai, Michael D. Sinanis, Abbas Semnani, Dimitrios Peroulis

The Summer Undergraduate Research Fellowship (SURF) Symposium

Over the past few decades, researchers have explored and implemented methods of wireless power transmission to operate devices that traditionally have been powered using plug-in power supplies and batteries. It is with this objective in mind that we built a boat, which is powered wirelessly from a field of harvestable energy. This project sought to develop a wirelessly powered remote control boat to be a proof of concept for the idea of wireless power transfer. Our criteria for success is that the boat should receive sufficient power to run anywhere in a 2.5 meter squared area. Having defined the field …

Simulation Design For Photovoltaics Using Finite Difference Time Domain And Quadratic Complex Rational Function Methods, Jacob R. Duritsch, Haejun Chung, Peter Bermel

The Summer Undergraduate Research Fellowship (SURF) Symposium

Photovoltaics (PV) can in principle supply enough renewable energy to offset a great deal of fossil fuel usage. To achieve this transition, it is critical to develop improved PV cells with decreased material costs and improved efficiencies. This goal can be greatly facilitated by a tool simulating the absorption and efficiency of experimentally relevant 3-D PV designs made of realistic materials, including those that have not yet been discovered. By incorporating the quadratic complex rational function algorithm (QCRF) with the finite difference time domain methods (FDTD), simulations can include frequency response and optical properties, while allowing full customization of tandem …

Temperature Dependence Of Electrical Performance Of Tritium Sourced Betavoltaic Cells, Darrell S. Cheu, Tom Adams, Shripad Revankar

The Summer Undergraduate Research Fellowship (SURF) Symposium

There is an increasing need for devices that can be powered for extended periods of time where it is impossible for maintenance or replacement, such as pacemakers, long term space flight or undisturbed sensors for military use. Since 1971, most devices run off a Lithium-Iodide battery, which gives a high amount of power but could only last approximately 2 to 5 years, requiring frequent replacement. However, replacement is unnecessary for betavoltaic cells as they can last at least 20 years. Commercially available tritium betavoltaic cells provided by City Labs Inc. were tested at a temperature range of -50°C to 150°C …

Broadband High Efficiency Fractal-Like And Diverse Geometry Silicon Nanowire Arrays For Photovoltaic Applications, Omar Hassan Al-Zoubi

Graduate Theses and Dissertations

Solar energy has many advantages over conventional sources of energy. It is abundant, clean and sustainable. One way to convert solar energy directly into electrical energy is by using the photovoltaic solar cells (PVSC). Despite PVSC are becoming economically competitive, they still have high cost and low light to electricity conversion efficiency. Therefore, increasing the efficiency and reducing the cost are key elements for producing economically more competitive PVSC that would have significant impact on energy market and saving environment. A significant percentage of the PVSC cost is due to the materials cost. For that, thin films PVSC have been …

The Future Of Rural Communities, Alondra B. Perez, Yanliang Zhang (Mentor)

Idaho Conference on Undergraduate Research

There is a problem in how modern energy is being distributed throughout the world; less than a quarter of the population have access to energy. Limited energy access is seen in rural areas because of the costs that comes from transporting material and making modern energy resources (solar panels, wind turbines, etc..). Through research on thermoelectric devices, there have been many theories tested in order to improve energy efficiency focusing on easy maneuverable resources. At Boise State’s Advanced Energy Lab, thermoelectric generators are being created and modified which can be used to help communities from rural areas power utilities needed …

Renewable Energy In Industrial Applications, Seshi Reddy Kasu

Dissertations, Theses and Capstone Projects (Full IR Collection)

Manufacturing industry accounts for about one third of total energy use worldwide. Roughly three quarters of industrial energy use is related to the production of energy-intensive commodities such as ferrous and non-ferrous metals, chemicals and petrochemicals, non-metallic mineral materials, and pulp and paper. In these sectors, energy costs constitute a large proportion of total production costs, so managers pay particular attention to driving them down. As a result, the scope to improve energy efficiency tends to be less in these most energy intensive sectors than in those sectors where energy costs form a smaller proportion of total costs, such as …

Current Status And Prospect Of Cathode Materials For Lithium Sulfur Batteries, Lan Zhou, Ai-Shui Yu

Journal of Electrochemistry

Elemental sulfur has been extensively investigated as a promising candidate of cathode material for next generation lithium secondary batteries. However, some troublesome issues, such as the low electric conductivity of sulfur (5×10^-30 S·cm^-1) and the high solubility of lithium polysulfide intermediates in organic electrolytes, resulting in a low utilization of active material and a redox shuttling of dissolved polysulfide ions between the sulfur cathode and the lithium anode, which eventually leads to a deposition of insoluble and insulating Li₂S₂/Li₂S on the electrode surface and a fast reduction in the specific capacity. …

Research Status And Application Prospects Of Limnpo4 As A New Generation Cathode Material For Lithium-Ion Batteries, Lai-Fen Qin, Yong-Gao Xia, Li-Peng Chen, Hua-Sheng Hu, Feng Xiao, Zhao-Ping Liu

Journal of Electrochemistry

Olivine-structured lithium manganese phosphate (LiMnPO₄) has the following advantages: excellent thermal stability, low cost, high safety and environmental benignity. Importantly, the theoretical energy density of LiMnPO₄ is about 20% higher than that of commercialized LiFePO₄ due to its higher Li⁺ intercalation potential of 4.1 V (vs. Li⁺/Li). Moreover, the high operating voltage of LiMnPO₄ is compatible with present non-aqueous organic electrolytes of lithium-ion batteries. Therefore, LiMnPO₄ is considered as a next generation cathode material for lithium-ion batteries. However, LiMnPO₄ suffers from poor electronic conductivity and low lithium diffusivity, resulting in …

Preparations And Applications Of Layered Carbon And Layered Carbon-Pbso4 Composite, Shu-Kai Zhang, Hao Zhang, Wei-Hua Xue, Jie Cheng, Wen-Feng Zhang, Gao-Ping Cao, Hai-Lei Zhao, Yu-Sheng Yang

Journal of Electrochemistry

The layered carbon materials (similar to graphene) have been synthesized by chemical vapor deposition (CVD) on the cheap catalyst (potassium or sodium carbonate substrate). The layered-carbon- lead sulfate (PbSO₄) composite could be prepared by in situ chemical deposition based on the layered carbon. The XRD, SEM and TEM results showed that the layered carbon materials was amorphous carbon layer, and the composite was a compound made of fine lead sulfate grains and layered carbon. Thermogravimetric analysis determined the carbon content in the composite. Adding a certain amount of layered carbon or layered-carbon-PbSO₄ composite into negative active materials …

Preparation Of Zro2-Doped Nb/Pbo2 Electrode And Electrocatalytic Performance Of Methyl Orange Degradation, Li Zhang, Wen-Yan Dong, Tai-Lai Yang, Zhen-Hai Liang

Journal of Electrochemistry

The zirconium oxide (ZrO₂)-doped niobium based lead oxide (Nb/PbO₂) electrode was prepared by electrodeposition. The microstructures and electrochemical properties of Nb/ZrO₂+PbO₂ electrode were investigated using scanning electron microscopy (SEM), X-ray diffraction (XRD), linear sweep voltammetry, electrochemical impedance spectroscopy and cyclic voltammotry. In addition, the Nb/PbO₂ electrode was used as an anode for the electrochemical degradation of methyl orange (MO). Results revealed that the ZrO₂ doping made the Nb/PbO2 electrode surface denser and rougher with smaller sized crystal particles, which increased the specific surface area and enhanced the electrocatalytic activity of the …

Electrochemical Mass Spectrometric Study Of Lithium-Oxygen Batteries, Xin-Xiu Yan, Li-Po Ma, Zhang-Quan Peng

Journal of Electrochemistry

Mass Spectrometry, coupled with electrochemistry, is a powerful research tool to study mechanisms for a broad range of electrode reactions by identifying and quantifying reaction products and intermediates. In this review, we summarize the recent advances in the Li-O₂ battery researches offered by electrochemical mass spectrometry based on our group investigations. These include the research progresses in electrolytes, cathode materials (electrocatalysts), and parasitic reactions, i.e., the key issues associated with Li-O₂ research. In addition, we also discuss the effects of irreversible side reactions involved in battery systems on charge and discharge processes.

Synthesis Of Graphene Wrapped Li-Rich Layered Metal Oxide And Its Electrochemical Performance, Meng-Yan Hou, Ke Wang, Xiao-Li Dong, Yong-Yao Xia

Journal of Electrochemistry

In present work, lithium-rich layered transition metal oxide (LLO) was synthesized by a co-precipitation method in combination with a solid-state reaction. The graphene wrapped Li-rich layered oxide composite (LLO/Gra) was obtained by sintering the LLO/GO composite at 300 ^oC for 30 min in an air. The morphologies and the electrochemical performances were characterized by means of SEM, TEM, XRD, XPS, EIS and charge/discharge tests. The results indicated that the LLOe particles were uniformly wrapped with graphene. The resulting material exhibited better rate capability than that of pristine LLO since the wrapped graphene demonstrated the enhanced electronic conductivity. Accordingly, the …

Research Progress In Carbon Coating On Lifepo4 Cathode Materials For Lithium Ion Batteries, Ning Zhang, Yong-Chang Liu, Cheng-Cheng Chen, Zhi-Qiang Zhu, Zhan-Liang Tao, Jun Chen

Journal of Electrochemistry

Olivine-structured LiFePO₄ has been received much attention because of its flat voltage profile, low cost, abundant material supply and better environmental compatibility. However, the poor electronic and ionic conductivities have limited its application in industry. One of the best methods to improve the electrochemical performance is carbon coating. In this review, we summarize the recent developments of LiFePO₄/C cathode. Moreover, the different effects caused by coating methods and carbon sources, as well as the mechanism of carbon coating on the properties of LiFePO₄/C are reviewed.

Enhancing Stability Of Pem Fuel Cell Catalysts Via Support Changing, Xiao-Hong Xie, Zi-Dong Wei

Journal of Electrochemistry

The Pt/C catalyst with highly dispersed Pt nanoparticles supported on carbon has been widely used as the state-of the-art catalyst in proton exchange membrane fuel cells (PEMFCs), while the durability of Pt/C is one of the major barriers for large-scale applications of PEMFCs. Thus, enhancing the stability of Pt/C has been a hot issue in this field. In this review, we summarize the recent progress in enhancing the catalyst stability in the view of support material. The future prospects of the PEMFCs catalyst should focus on adopting more stable supports or strengthening the interactions between Pt and supports.

Pt/C Modified Proton Exchange Membrane For Improved Fuel Cell Performance, Zhi Cui, Chao Wang, Shui-Yun Shen, Feng-Jing Jiang, Jun-Liang Zhang

Journal of Electrochemistry

The property of proton exchange membrane greatly affects the performance of proton exchange membrane fuel cells (PEMFC). During the operation of a PEMFC, the water produced at the cathode, the water vapor from the humidified feed gas and the water migrated by electro-dragging will reach a balance in the membrane and determine the resistance of PEMFC, and thus affect the performance of PEMFC. Normally, the PEMFC performance strongly depends on the relative humidity of the feed gas, and the performance decreases at lower humidity as a result of lower proton conductivity of the membrane. In this paper, we proposed to …

Electrolytes For Lithium And Lithium-Ion Batteries, Zong-Rang Zhang

Journal of Electrochemistry

This is an up-to-date book published by Springer last year and focuses on the field of the electrolytes for lithium and lithium-ion batteries. A brief introduction and review of this book are given in this paper. The main contents of this book are introduced briefly in the order of ten different chapters along with a short review of recent progress in those fields.

Lithium Air Batteries: Non-Aqueous And Hybrid Systems, Sheng-Fu Tong, Ping He, Xue-Ping Zhang, Shi-Yong Zhao, Hao-Shen Zhou

Journal of Electrochemistry

Developing energy storage devices and new materials, which match the requirements in electric vehicles (EVs) and hybrid electric vehicles (HEVs), is an effective way to balance the contradiction between the social development and the shortage of fossil energy and environment pollution. Rechargeable lithium-air (Li-air) batteries consisting of Li and oxygen as the anodic and cathodic reactants, respectively, have attracted much attention during the past decade due to their high theoretical specific energy. According to work conditions, the most studied types of Li-air batteries are non-aqueous, hybrid, and solid state electrolyte Li-air batteries. Challenges still exist in cathodes, anodes, electrolytes and …

Time-Variant Load Models Of Electric Vehicle Chargers, Nicole P. Zimmerman

Dissertations and Theses

In power distribution system planning, it is essential to understand the impacts that electric vehicles (EVs), and the non-linear, time-variant loading profiles associated with their charging units, may have on power distribution networks. This research presents a design methodology for the creation of both analytical and behavioral models for EV charging units within a VHDL-AMS simulation environment.

Voltage and current data collected from Electric Avenue, located on the Portland State University campus, were used to create harmonic profiles of the EV charging units at the site. From these profiles, generalized models for both single-phase (Level 2) and three-phase (Level 3) …

Minimizing Sheet Resistance Of Organic Photovoltaic Cell Top Contact Electrode Layer: Silver Nanowire Concentration Vs. Conductive Polymer Doping Concentration, Caitlyn Cook

Materials Engineering

The top contact electrode layers of nine organic photovoltaic cells were prepared with two varying factors: three Silver nanowire (AgNW) densities deposited on a conductive polymer doped with three concentrations. Silver’s low sheet resistance of 20-Ω/sq is hypothesized to lower the sheet resistance of the anode layer and thus enhance the overall efficiency of the cell. Four-point probe measurements indicated that increasing AgNW density in the top contact electrode layer of an organic photovoltaic cell significantly reduces sheet resistance from 52.2k-Ω/sq to 18.0 Ω/sq. Although an increase in doping concentration of the conductive polymer reduced sheet resistance in low AgNW …

Enterprise Smart Outlet, David Faltmier, Matthew Mcgill, Luke Stencel

Electrical Engineering

The purpose of our senior project, Enterprise Smart Outlet, is to create an electrical outlet which will allow enterprise users to monitor and change their power consumption habits on a large scale. The initial goal of this project is to allow consumers to see their power consumption per outlet in real time, and then using that information conform their future habits to help them conserve electrical energy, and more importantly, money. Three requirements for our project to meet our initial goal are, the outlet will work in a standard electrical outlet and be completely compatible with current electrical standards, the …

Department Of Energy Solar Decathlon 2015, Dante C. Carrillo, Dion A. Celebrado, Jenna I. Denhaan, Christian F. Ferrer, Simon D. Hauser, Audrey L. Rempher, Joseph H. Rohrer, Casey S. Smith

Electrical Engineering

The goal of the Department of Energy (DOE) Solar Decathlon 2015 project is to design, build, and operate a zero-net energy solar-photovoltaic (solar-PV) powered residence. It is an international competition taking place in the fall of 2015 in Irvine, California. The design needs to be attractive, energy-efficient, innovative, and affordable. The Cal Poly team includes students from a variety of majors, including Architecture, Mechanical Engineering, Electrical Engineering, and many more. The different disciplines need to work together to create a functional and cohesive design. For our senior project, we have designed the electrical systems in the home, including the power, …