Power and Energy Commons^™

Rethinking Wind In Kentucky, Lawrence E. Holloway, Aron Patrick, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Recent analyses and developments suggest that wind energy could play a role in Kentucky's future power generation mix. This recent change in outlook for Kentucky wind has been driven by three factors: (1) improved wind turbine technologies, (2) improved economics, and (3) recent analyses showing improved grid reliability due to wind's complementarity to solar power generation.

Dynamic Model Of Ac-Ac Dual Active Bridge Converter Using The Extended Generalized Average Modeling Framework, Kartikeya Jayadurga Prasad Veeramraju, Jonathan W. Kimball

Electrical and Computer Engineering Faculty Research & Creative Works

The ac-ac dual active bridge (DAB) converter is an advanced bidirectional two-port grid interface converter that facilitates active and reactive power flow control between two grids without a dc-link capacitor. This article presents a novel modeling approach for the ac-ac DAB converter using the extended generalized average modeling (EGAM) technique. Unlike the conventional generalized average modeling (GAM) framework, the ac-ac DAB converter's dynamic state variables, including the leakage inductor current and ac grid side LC filters, exhibit grid and switching frequency components, making the standard GAM framework unsuitable for dynamic modeling involving two distinct excitation frequencies. Furthermore, the 2-D GAM …

An Impedance-Source-Based Soft-Switched High Step-Up Dc-Dc Converter With An Active Clamp, Saeed Habibi, Ramin Rahimi, Mehdi Ferdowsi, Pourya Shamsi

Electrical and Computer Engineering Faculty Research & Creative Works

This article proposes a high step-up dc-dc converter based on a trans-inverse impedance-source structure, in which the voltage gain of the converter is increased by using a lower number of turns ratio of the coupled inductors (CI) windings. The proposed converter achieves a very high voltage gain and a very low voltage stress on the switches. An active clamp is incorporated into the topology of the proposed converter, helping to absorb the energy of the leakage inductances of the CI, and to recycle that energy to the output of the converter to further increase the voltage gain. Furthermore, the active …

A Study On The Incentives And Barriers For The Adoption Of Electric Vehicles In South Alabama, Marianne Loes, Daniela Wolter Ferreira Touma, Jennifer C. Zoghby

Association of Marketing Theory and Practice Proceedings 2024

ABSTRACT

Through a series of public policy incentives and consumer demand, more electric vehicles are being sold nationwide than ever before. Although electric vehicles (EVs) are being adopted nationwide by many consumers in recent years, car-buyers across South Alabama have not followed the trend. This research considers different stakeholders in the complex consumer buying process of car purchases, and it uses the extant technology adoption models to assess the public policy incentives, as well as statewide roadblocks, to EV adoption.

Support The Next Generation By Sponsoring The 2024 Windstorm Challenge!, Advanced Structures And Composites Center

General University of Maine Publications

The Windstorm Challenge is a unique opportunity for middle and high school students to get hands-on engineering practice at the Advanced Structures and Composites Center (ASCC). Organized by the same team that brings you AFloat, the Windstorm Challenge seeks to educate the next generation of floating offshore wind innovators.

Energy Efficiency In Additive Manufacturing: Condensed Review, Ismail Fidan, Vivekanand Naikwadi, Suhas Alkunte, Roshan Mishra, Khalid Tantawi

Engineering Technology Faculty Publications

Today, it is significant that the use of additive manufacturing (AM) has growing in almost every aspect of the daily life. A high number of sectors are adapting and implementing this revolutionary production technology in their domain to increase production volumes, reduce the cost of production, fabricate light weight and complex parts in a short period of time, and respond to the manufacturing needs of customers. It is clear that the AM technologies consume energy to complete the production tasks of each part. Therefore, it is imperative to know the impact of energy efficiency in order to economically and properly …

Designing High-Performance Identity-Based Quantum Signature Protocol With Strong Security, Sunil Prajapat, Pankaj Kumar, Sandeep Kumar, Ashok Kumar Das, Sachin Shetty, M. Shamim Hossain

VMASC Publications

Due to the rapid advancement of quantum computers, there has been a furious race for quantum technologies in academia and industry. Quantum cryptography is an important tool for achieving security services during quantum communication. Designated verifier signature, a variant of quantum cryptography, is very useful in applications like the Internet of Things (IoT) and auctions. An identity-based quantum-designated verifier signature (QDVS) scheme is suggested in this work. Our protocol features security attributes like eavesdropping, non-repudiation, designated verification, and hiding sources attacks. Additionally, it is protected from attacks on forgery, inter-resending, and impersonation. The proposed scheme benefits from the traditional designated …

The Need For Energy Storage On Renewable Energy Generator Outputs To Lessen The Geeth Effect, I.E. Short-Term Variations Mainly Associated With Wind Turbine Active Power Output, Tony Kealy

Articles

Many studies investigating the short-term variations associated with the power output from wind turbine generators utilise simulated or modelled data in the analysis. This current study uses short-term empirical data downloaded directly from operational wind turbines via electrical power quality meters. The empirical data shows that the short-term variations (one-second or sub-one-second timeframe) occur continuously over most of the power output range. A novel name is proposed, the Geeth Effect, for this variability phenomenon. The Geeth Effect is measured using the coefficient of variation mathematical expression and is likely contributing to (i) lower-than-expected financial and environmental benefits associated with …

Vertical Free-Swinging Photovoltaic Racking Energy Modeling: A Novel Approach To Agrivoltaics, Koami Soulemane Hayibo, Joshua M. Pearce

Electrical and Computer Engineering Publications

To enable lower-cost building materials, a free-swinging bifacial vertical solar photovoltaic (PV) rack has been proposed, which complies with Canadian building codes and is the lowest capital-cost agrivoltaics rack. The wind force applied to the free-swinging PV, however, causes it to have varying tilt angles depending on the wind speed and direction. No energy performance model accurately describes such a system. To provide a simulation model for the free-swinging PV, where wind speed and direction govern the array tilt angle, this study builds upon the open-source System Advisor Model (SAM) using Python. After the SAM python model is validated, a …

Poster: Optimising Electric Vehicle Charging Infrastructure In Dublin Using Geecharge, Alexander Mutiso Mutua, Ruairí De Fréin, Ali Malik, Kibanza Eliel, Sahbane Marco, Pantel Maxime

Conference papers

Range anxiety is a significant challenge affecting electric vehicles use as drivers fear running out of charge without finding a charging point on time. We develop methods to optimise the distribution of charging points. EV portacharge and GEECharge solutions distribute charging points in a city by considering the population density and Points Of Interest (POI) or road traffic. This paper focuses on (1) developing and evaluating methods to distribute Charging Points (CPs) in Dublin city; (2) optimising CP allocation; (3) visualising paths in the graph network to show the most used roads and points of interest; (4) describing a way …

Power Outage And Environmental Justice In Winter Storm Uri: An Analytical Workflow Based On Nighttime Light Remote Sensing, Jinwen Xu, Yi Qiang, Heng Cai, Lei Zou

GIS Center

The intensity of extreme weather events has been increasing, posing a unique threat to society and highlighting the importance of our electrical power system, a key component in our infrastructure. In severe weather events, quickly identifying power outage impact zones and affected communities is crucial for informed disaster response. However, a lack of household-level power outage data impedes timely and precise assessments. To address these challenges, we introduced an analytical workflow using NASA’s Black Marble daily nighttime light (NTL) images to detect power outages from the 2021 Winter Storm Uri. This workflow includes adjustments to mitigate viewing angle and snow …

Round Trip Time Measurement Over Microgrid Power Network, Yasin Emir Kutlu, Ruairí De Fréin, Malabika Basu, Ali Malik

Conference papers

A focus of the Power Systems and Networking communities is the design and deployment of Microgrid (MG) integration systems that ensure that quality of service targets are met for load sharing systems at different endpoints. This paper presents an integrated Microgrid testbed that allows Microgrids endpoints to share their current, voltage and power values using a Network Published Shared Variable (NPSV) approach. We present Round Trip Time (RTT) measurements for time sensitive Microgrid control traffic in the presence of varying background traffic as an example quality of service measurement. Numerical results are presented using a range of different background traffic …

Poster: Round Trip Time Measurement Over Microgrid Power Network, Yasin Emir Kutlu, Ruairí De Fréin, Malabika Basu, Ali Malik

Conference papers

A focus of the Power Systems and Networking communities is the design and deployment of Microgrid (MG) integration systems that ensure that quality of service targets are met for load sharing systems at different endpoints. This paper presents an integrated Microgrid testbed that allows Microgrids endpoints to share their current, voltage and power values using a Network Published Shared Variable (NPSV) approach. We present Round Trip Time (RTT) measurements for time sensitive Microgrid control traffic in the presence of varying background traffic as an example quality of service measurement. Numerical results are presented using a range of different background traffic …

Integrated Dc Microgrid Testbed For Qos Evaluation, Yasin Emir Kutlu, Ruairí De Fréin, Malabika Basu, Ali Malik

Conference papers

This poster describes the development of an integrated Direct Current (DC) Microgrid (MG) testbed, consisting of power system and computer networking hardware, e.g. Cisco 4331 Integrated Services Routers (ISR) and 500W AC/DC power supplies, to test the Quality of Service (QoS) of MG control packets which are delivered over Layer-2 and Layer-3 networking topologies. It facilitates an examination of control packets between MG end-points, that enable real-time power load sharing, in the presence of background computer network traffic such as video streaming. The effects of difference levels of background traffic on the round trip time of control packets are demonstrated.

Control And Design Of A Passive Solar Lumber Drying Kiln, Peter Chardavoyne

Honors Scholar Theses

The passive solar lumber drying kiln design, developed by EE Senior Design Team 2317 is presented, tested, and discussed. The design incorporates solar power and a custom control system to dry 12’ lumber boards inside a shipping container much faster than air-drying methods, which can take up to a year for thorough drying, though this can be extended due to the unpredictability of weather events and conditions. This work presents the design as in the final report provided by the team, but provides a more detailed explanation and analysis of the microcontroller system, testing methods and outcomes, alternate solutions and …

Design Optimization Of A Direct-Drive Wind Generator With Non-Rare-Earth Pm Flux Intensifying Stator And Reluctance Rotor, Ali Mohammadi, Oluwaseun A. Badewa, Yaser Chulaee, Dan Ionel, Somasundaram Essakiappan, Madhav Manjrekar

Power and Energy Institute of Kentucky Faculty Publications

This paper presents a multi-objective design optimization for a novel direct-drive wind turbine generator. The proposed electric machine topology employs an outer rotor of the reluctance type and a special modular stator including three phase-windings and spoke-type permanent magnets (PMs). Each stator module includes a single coil toroidally wound around the ferromagnetic core. Consecutive stator modules are separated by PMs and include coils belonging to a different phase. An optimization method with three objectives: total power loss, weight, and torque ripple, and with one constraint for a minimum acceptable value for the power factor, is described. The design examples are …

Torque And Power Capabilities Of Coreless Axial Flux Machines With Surface Pms And Halbach Array Rotors, Yaser Chulaee, Donovin Lewis, Matin Vatani, John F. Eastham, Dan Ionel

Power and Energy Institute of Kentucky Faculty Publications

This paper investigates employing a Halbach PM rotor array to increase torque and power density within coreless axial flux permanent magnet (AFPM) machines. Analytical and 2/3-dimensional finite element analysis (FEA) methods are developed to study torque and power capabilities within an example double-rotor, single-stator coreless AFPM machine with a PCB stator. Compared to a surface PM topology of the same mass and volume, employing a Halbach array increases torque density by as much as 30% through increased airgap flux density amplitude. Multiple parametric studies are performed to explore methods of increasing torque and power density while employing Halbach arrays combined …

Statistical Analysis And Degradation Pathway Modeling Of Photovoltaic Minimodules With Varied Packaging Strategies, Sameera Nalin Venkat, Xuanji Yu, Jiqi Liu, Jakob Wegmueller, Jayvic Cristian Jimenez, Erika I. Barcelos, Hein Htet Aung, Roger H. French, Laura S. Bruckman

Faculty Scholarship

Degradation pathway models constructed using network structural equation modeling (netSEM) are used to study degradation modes and pathways active in photovoltaic (PV) system variants in exposure conditions of high humidity and temperature. This data-driven modeling technique enables the exploration of simultaneous pairwise and multiple regression relationships between variables in which several degradation modes are active in specific variants and exposure conditions. Durable and degrading variants are identified from the netSEM degradation mechanisms and pathways, along with potential ways to mitigate these pathways. A combination of domain knowledge and netSEM modeling shows that corrosion is the primary cause of the power …

Chatgpt As Metamorphosis Designer For The Future Of Artificial Intelligence (Ai): A Conceptual Investigation, Amarjit Kumar Singh (Library Assistant), Dr. Pankaj Mathur (Deputy Librarian)

Library Philosophy and Practice (e-journal)

Abstract

Purpose: The purpose of this research paper is to explore ChatGPT’s potential as an innovative designer tool for the future development of artificial intelligence. Specifically, this conceptual investigation aims to analyze ChatGPT’s capabilities as a tool for designing and developing near about human intelligent systems for futuristic used and developed in the field of Artificial Intelligence (AI). Also with the helps of this paper, researchers are analyzed the strengths and weaknesses of ChatGPT as a tool, and identify possible areas for improvement in its development and implementation. This investigation focused on the various features and functions of ChatGPT that …

Senior Design Project - Ev Charger And Distributed Energy Resources, Eric Iliyev, Mostafa Younes, Abanoub Said, Carlos Figueroa, Ahmed Mohamed

Open Educational Resources

No abstract provided.

Circulating And Eddy Current Losses In Coreless Axial Flux Pm Machine Stators With Pcb Windings, Yaser Chulaee, Donovin Lewis, Ali Mohammadi, Greg Heins, Dean Patterson, Dan Ionel

Power and Energy Institute of Kentucky Faculty Publications

Printed circuit board (PCB) stators in coreless axial flux permanent magnet (AFPM) machines have been proposed, designed, and studied for use in multiple industries due to their design flexibility and reduction of manufacturing costs, volume, and weight compared to conventional stators. This paper investigates mechanisms and methods of approximating open circuit losses in PCB stators within example wave and spiral winding topologies for a dual rotor, single stator configuration using 3D FEA, analytical hybrid techniques and experiments. The effect of rotor magnet shape, end winding, and active conductor geometry on eddy currents is studied, and some mitigation techniques are proposed. …

Decarbonization Analysis For Thermal Generation And Regionally Integrated Large-Scale Renewables Based On Minutely Optimal Dispatch With A Kentucky Case Study, Donovin Lewis, Aron Patrick, Evan S. Jones, Rosemary E. Alden, Abdullah Al Hadi, Malcolm D. Mcculloch, Dan Ionel

Power and Energy Institute of Kentucky Faculty Publications

Decarbonization of existing electricity generation portfolios with large-scale renewable resources, such as wind and solar photo-voltaic (PV) facilities, is important for a transition to a sustainable energy future. This paper proposes an ultra-fast optimization method for economic dispatch of firm thermal generation using high granularity, one minute resolution load, wind, and solar PV data to more accurately capture the effects of variable renewable energy (VRE). Load-generation imbalance and operational cost are minimized in a multi-objective clustered economic dispatch problem with various generation portfolios, realistic generator flexibility, and increasing levels of VRE integration. The economic feasibility of thermal dispatch scenarios is …

Energy-Efficient Multi-Rate Opportunistic Routing In Wireless Mesh Networks, Mohammad Ali Mansouri Khah, Neda Moghim, Nasrin Gholami, Sachin Shetty

VMASC Publications

Opportunistic or anypath routing protocols are focused on improving the performance of traditional routing in wireless mesh networks. They do so by leveraging the broadcast nature of the wireless medium and the spatial diversity of the network. Using a set of neighboring nodes, instead of a single specific node, as the next hop forwarder is a crucial aspect of opportunistic routing protocols, and the selection of the forwarder set plays a vital role in their performance. However, most opportunistic routing protocols consider a single transmission rate and power for the nodes, which limits their potential. To address this limitation, this …

Editorial: Internet Of Energy For Renewable Energy-Based Decarbonized Electrical Energy Systems, Onur Elma, Murat Kuzlu, Nasibeh Zohrabi

Engineering Technology Faculty Publications

[Introduction] This research topic aims to highlight the current state-of-the art technologies in digitalized smart grids, including renewable energy and others with the Internet of Energy (IoE) under the decarbonized electrical energy systems. These approaches will increase the overall efficiency of electrical power systems, along with emerging technologies and applications in the current system. IoE covers all digitalization processes with mobility, electronic devices, and energy network as seen in Figure 1.

Optimising Electric Vehicle Charging Infrastructure In Dublin Using Geecharge, Alexander Mutua Mutiso, Ruairí De Fréin, Ali Malik, Eliel Kibanza, Marco Sahbane, Maxime Pantel

Conference papers

Range anxiety poses a hurdle to the adoption of Electric Vehicles (EVs), as drivers worry about running out of charge without timely access to a Charging Point (CP). We present novel methods for optimising the distribution of CPs, namely, EV portacharge and GEECharge. These solutions distribute CPs in Dublin, in this paper, by considering the population density and Points Of Interest (POIs) or road traffic. The object of this paper is to (1) develop and evaluate methods to distribute CPs in Dublin city; (2) optimise CP allocation; (3) visualise paths in the graph network to show the most used roads …

Multi-Layered Energy Management Framework For Extreme Fast Charging Stations Considering Demand Charges, Battery Degradation, And Forecast Uncertainties, Waqas Ur Rehman, Jonathan W. Kimball, Rui Bo

Electrical and Computer Engineering Faculty Research & Creative Works

To achieve a cost-effective and expeditious charging experience for extreme fast charging station (XFCS) owners and electric vehicle (EV) users, the optimal operation of XFCS is crucial. It is however challenging to simultaneously manage the profit from energy arbitrage, the cost of demand charges, and the degradation of a battery energy storage system (BESS) under uncertainties. This paper, therefore, proposes a multi-layered multi-time scale energy flow management framework for an XFCS by considering long- and short-term forecast uncertainties, monthly demand charges reduction, and BESS life degradation. In the proposed approach, an upper scheduling layer (USL) ensures the overall operation economy …

Survey Of Routing Techniques-Based Optimization Of Energy Consumption In Sd-Dcn, Mohammed Nsaif, Gergely Kovásznai, Ali Malik, Ruairí De Fréin

Articles

The increasing power consumption of Data Center Networks (DCN) is becoming a major concern for network operators. The object of this paper is to provide a survey of state-of-the-art methods for reducing energy consumption via (1) enhanced scheduling and (2) enhanced aggregation of traffic flows using Software-Defined Networks (SDN), focusing on the advantages and disadvantages of these approaches. We tackle a gap in the literature for a review of SDN-based energy saving techniques and discuss the limitations of multi-controller solutions in terms of constraints on their performance. The main finding of this survey paper is that the two classes of …

Continuity Of Formal Power Series Products In Nonlinear Control Theory, W. Steven Gray, Mathias Palmstrøm, Alexander Schmeding

Electrical & Computer Engineering Faculty Publications

Formal power series products appear in nonlinear control theory when systems modeled by Chen–Fliess series are interconnected to form new systems. In fields like adaptive control and learning systems, the coefficients of these formal power series are estimated sequentially with real-time data. The main goal is to prove the continuity and analyticity of such products with respect to several natural (locally convex) topologies on spaces of locally convergent formal power series in order to establish foundational properties behind these technologies. In addition, it is shown that a transformation group central to describing the output feedback connection is in fact an …

Mitigating Anomalous Electricity Consumption In Smart Cities Using An Ai-Based Stacked-Generalization Technique, Arshid Ali, Laiq Khan, Nadeem Javaid, Safdar Hussain Bouk, Abdulaziz Aldegheishem, Nabil Alrahjeh

Computer Science Faculty Publications

Energy management and efficient asset utilization play an important role in the economic development of a country. The electricity produced at the power station faces two types of losses from the generation point to the end user. These losses are technical losses (TL) and non-technical losses (NTL). TLs occurs due to the use of inefficient equipment. While NTLs occur due to the anomalous consumption of electricity by the customers, which happens in many ways; energy theft being one of them. Energy theft majorly happens to cut down on the electricity bills. These losses in the smart grid (SG) are the …

A Review Of Piezoelectric Footwear Energy Harvesters: Principles, Methods, And Applications, Bingqi Zhao, Feng Qian, Alexander Hatfield, Lei Zuo, Tian-Bing Xu

Mechanical & Aerospace Engineering Faculty Publications

Over the last couple of decades, numerous piezoelectric footwear energy harvesters (PFEHs) have been reported in the literature. This paper reviews the principles, methods, and applications of PFEH technologies. First, the popular piezoelectric materials used and their properties for PEEHs are summarized. Then, the force interaction with the ground and dynamic energy distribution on the footprint as well as accelerations are analyzed and summarized to provide the baseline, constraints, potential, and limitations for PFEH design. Furthermore, the energy flow from human walking to the usable energy by the PFEHs and the methods to improve the energy conversion efficiency are presented. …