Power and Energy Commons^™

Recent Advances In Solar Photo(Electro)Catalytic Nitrogen Fixation, Jun-Bo Ma, Sheng Lin, Zhiqun Lin, Lan Sun, Chang-Jian Lin

Journal of Electrochemistry

Ammonia (NH₃) is an essential chemical in modern society. It is currently produced in industry by the Haber-Bosch process using H₂ and N₂ as reactants in the presence of iron-based catalysts at high-temperature (400–600 ^oC) and extremely highpressure (20–40 MPa) conditions. However, its efficiency is limited to 10% to 15%. At the same time, a large amount of energy is consumed, and CO₂ emission is inevitably. The development of a sustainable, clean, and environmentally friendly energy system represents a key strategy to address energy crisis and environmental pollution, ultimately aiming to achieve carbon neutrality. …

Development Of A Mathematical Model Of Magnetic Field Distribution In Magnetic Conductors Of A Wide-Range Current Transformer, Abdurauf Safarov

Chemical Technology, Control and Management

The article is devoted to the analysis of the distribution of the magnetic field in the magnetic conductors of a wide-range current transformer for the development of a mathematical model that can be used as the basis for calculating its static characteristics and error. The design, replacement circuits and design model of a current transformer are given. The relations of magnetic induction and tension from the coordinate of the position of the primary winding are obtained. It is shown that the conversion range can be adjusted depending on the different positions of the bus with current, as a result of …

The Top Ten Scientific Questions In Electrochemistry, Chinese Society Of Electrochemistry

Journal of Electrochemistry

No abstract provided.

Rational Design Of Heterostructured Nanomaterials For Accelerating Electrocatalytic Hydrogen Evolution Reaction Kinetics In Alkaline Media, Hai-Bin Ma, Xiao-Yan Zhou, Jia-Yi Li, Hong-Fei Cheng, Ji-Wei Ma

Journal of Electrochemistry

Owing to the merits of high energy density, as well as clean and sustainable properties, hydrogen has been deemed to be a prominent alternative energy to traditional fossil fuels. Electrocatalytic hydrogen evolution reaction (HER) has been considered to be mostly promising for achieving green hydrogen production, and has been widely studied in acidic and alkaline solutions. In particular, HER in alkaline media has high potential to achieve large-scale hydrogen production because of the increased durability of electrode materials. However, for the currently most prominent catalyst Pt, its HER kinetics in an alkaline solution is generally 2–3 orders lower than that …

Electrochemical Performance Of Porous Ceramic Supported Tubular Solid Oxide Electrolysis Cell, Heng-Ji Wang, Wen-Guo Chen, Zhou-Yi Quan, Kai Zhao, Yi-Fei Sun, Min Chen, Ogenko Volodymyr

Journal of Electrochemistry

Solid oxide electrolysis cell (SOEC) is an efficient and clean energy conversion technology that can utilize electricity obtained from renewable resources, such as solar, wind, and geothermal energy to electrolyze water and produce hydrogen. The conversion of abundant intermittent energy to hydrogen energy would facilitate the efficient utilization of energy resources. SOEC is an all-ceramic electrochemical cell that operates in the intermediate to high temperature range of 500–750 ℃. Compared with traditional low temperature electrolysis technology (e.g., alkaline or proton exchange membrane cells operating at ~100 ℃), the high-temperature SOEC can increase the electrolysis efficiency from 80% to ~100%, providing …

An In-Situ Raman Spectroscopic Study On The Interfacial Process Of Carbonate-Based Electrolyte On Nanostructured Silver Electrode, Yu Gu, Yuan-Fei Hu, Wei-Wei Wang, En-Ming You, Shuai Tang, Jian-Jia Su, Jun Yi, Jia-Wei Yan, Zhong-Qun Tian, Bing-Wei Mao

Journal of Electrochemistry

The solid-electrolyte interphase (SEI) plays a key role in anodes for rechargeable lithium-based battery technologies. However, a thorough understanding in the mechanisms of SEI formation and evolution remains a major challenge, hindering the rapid development and wide applications of Li-based batteries. Here, we devise a borrowing surface-enhanced Raman scattering (SERS) activity strategy by utilizing a size optimized Ag nanosubstrate to in-situ monitor the formation and evolution of SEI, as well as its structure and chemistry in an ethylene carbonate-based electrolyte. To ensure a reliable in-situ SERS investigation, we designed a strict air-tight Raman cell with a three-electrode configuration. Based on …

Constructing Carbon-Encapsulated Nifev-Based Electrocatalysts By Alkoxide-Based Self-Template Method For Oxygen Evolution Reaction, En-Hui Ma, Xu-Po Liu, Tao Shen, De-Li Wang

Journal of Electrochemistry

The development of green and sustainable water-splitting hydrogen production technology is beneficial to reducing the over-reliance on fossil fuels and realizing the strategic goal of "carbon neutral". As one of the half reactions for water splitting, oxygen evolution reaction has suffered the problems of sluggish four-electron transfer process and relatively slow reaction kinetics. Therefore, exploring efficient and stable catalysts for oxygen evolution reaction is of critical importance for water-splitting technology. Metal alkoxides are a series of compounds formed by the coordination function of metal ions with alcohol molecules. Metal alkoxides possess the double advantages of organic materials and inorganic materials, …

Surface Modifications Of Lini0.96Co0.02Mn0.02O2 With Tungsten Oxide And Phosphotungstic Acid, Gang Zhao, Zheng-Liang Gong, Yi-Xiao Li, Yong Yang

Journal of Electrochemistry

With the rapid development of electric vehicles, enormous demands are made for higher energy density, better cycling performance and lower cost of lithium-ion batteries (LIBs). As an important high capacity cathode material for LIBs, the high nickel layered oxide material LiNi_0.8Co_0.1Mn_0.1O₂(NCM811) can reach an energy density of 760 Wh·kg^-1. The ultra-high nickel ternary positive electrode material (LiNi_1-x-yCo_xMn_yO₂, x ≥ 0.90) has a specific capacity of more than 210 mAh·g^-1, and can realize higher energy density. Besides, an ultra-high nickel material …

Preparation And Electrocatalytic Performance Of Feni-Cop/Nc Bifunctional Catalyst, Si-Miao Liu, Jing-Jiao Zhou, Shi-Jun Ji, Zhong-Sheng Wen

Journal of Electrochemistry

Rechargeable zinc-air batteries have gradually attracted much attention worldwide due to their high capacity, high energy density and low price. Oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) correspond to the charging and discharging processes in rechargeable zinc-air battery, respectively. At present, commercial Pt/C and IrO₂ catalysts hinder the large-scale application of zinc-air batteries due to low reserves, high prices and poor stability. Therefore, exploring high performance, low cost and high stability with dual functional catalysts is important for the development of rechargeable zinc-Air batteries. The metal-organic frameworks (MOFs) have high specific surface area, structural stability, good catalytic …

Hydrophobicity Optimization Of Cathode Catalyst Layer For Proton Exchange Membrane Fuel Cell, Hao-Jie Chen, Mei-Hua Tang, Sheng-Li Chen

Journal of Electrochemistry

Hydrophobicity of the cathode catalyst layers (CCLs) crucially determines the performance of proton exchange membrane fuel cells (PEMFCs) by affecting the transports of oxygen and liquid water. In this regard, polytetrafluoroethylene (PTFE) is usually used as a hydrophobic additive to facilitate the oxygen and water transports in CCLs. So far, there remains lacking systematic effort to optimize the addition methods of PTFE in CCLs and the mechanisms behind. In this work, the effects of the approaches for PTFE addition and the distribution of PTFE on the mass transport of oxygen and the proton conduction in CCLs were studied by using …

Synthesis And Evaluation Of Organic Additives For Copper Electroplating Of Interconnects, Yue-Hui Zhai, Yi-Xiao Peng, Yan Hong, Yuan-Ming Chen, Guo-Yun Zhou, Wei He, Peng-Ju Wang, Xian-Ming Chen, Chong Wang

Journal of Electrochemistry

Copper interconnects are essential to the functionality, performance, power efficiency, reliability, and fabrication yield of electronic devices. They are widely found in chips, packaging substrates and printed circuit boards, and are often produced by copper electroplating in an acidic aqueous solution. Organic additives play a decisive role in regulating copper deposition to fill microgrooves, and micro-vias to form fine lines and interlayer interconnects. Generally, an additive package consists of three components (brightener, suppressor, and leveler), which have a synergistic effect of super-filling on electroplating copper when the concentration ratio is appropriate. Many works of literature have discussed the mechanism of …

Band Alignments Of Metal/Oxides-Water Interfaces Using Ab Initio Molecular Dynamics, Yong-Bin Zhuang, Jun Cheng

Journal of Electrochemistry

Band alignments of electrode-water interfaces are of crucial importance for understanding electrochemical interfaces. In the scenario of electrocatalysis, applied potentials are equivalent to the Fermi levels of metals in the electrochemical cells; in the scenario of photo(electro)catalysis, semiconducting oxides under illumination have chemical reactivities toward redox reactions if the redox potentials of the reactions straddle the conduction band minimums (CBMs) or valence band maximums (VBMs) of the oxides. Computational band alignments allow us to obtain the Fermi level of metals, as well as the CBM and VBM of semiconducting oxides with respect to reference electrodes. In this tutorial, we describe …

Recent Progress Of Bifunctional Electrocatalysts For Oxygen Electrodes In Unitized Regenerative Fuel Cells, Tian-Long Zheng, Ming-Yu Ou, Song Xu, Xin-Biao Mao, Shi-Yi Wang, Qing-Gang He

Journal of Electrochemistry

Unitized regenerative fuel cells (URFCs), which oxidize hydrogen to water to generate electrical power under thefuel cells (FCs) mode and electrolyze water to hydrogen under the water electrolysis (WE) mode for recycling, areknown as clean and sustainable energy conversion devices. In contrast to the hydrogen oxidation reaction (HOR) andhydrogen evolution reaction (HER) on the hydrogen electrode side, the sluggish kinetics of oxygen reduction reaction(ORR) and oxygen evolution reaction (OER) on the oxygen electrode side requires highly efficient bifunctional oxygencatalysts. Conventional precious metal oxygen catalysts combine Pt and IrO₂ with excellent ORR and OER activities toachieve bifunctional electrocatalysis performance, but …

Deep Euteceic Solvents-Assisted Synthesis Of Novel Network Nanostructures For Accelerating Formic Acid Electrooxidation, Jun-Ming Zhang, Xiao-Jie Zhang, Yao Chen, Ying-Jian Fan, You-Jun Fan, Jian-Feng Jia

Journal of Electrochemistry

Deep eutectic solvents (DESs) have been reported as a type of solvent for the controllable synthesis of metal nanostructures. Interestingly, flower-like palladium (Pd) nanoparticles composed of staggered nanosheets and nanospheres are spontaneously transformed into three-dimensional (3D) network nanostructures in choline chloride-urea DESs using ascorbic acid as a reducing agent. Systematic studies have been carried out to explore the formation mechanism, in which DESs itself acts as a solvent and soft template for the formation of 3D flower-like network nanostructures (FNNs). The amounts of hexadecyl trimethyl ammonium bromide and sodium hydroxide also play a crucial role in the anisotropic growth and …

Fe Nanoparticles Encapsulated In N-Doped Porous Carbon For Efficient Oxygen Reduction In Alkaline Media, Chun-Yan Li, Rui Zhang, Xiao-Jie Ba, Xiao-Le Jiang, Yao-Yue Yang

Journal of Electrochemistry

Rational design and synthesis of non-precious-metal catalyst plays an important role in improving the activity and stability for oxygen reduction reaction (ORR) but remains a major challenge. In this work, we used a facile approach to synthesize iron nanoparticles encapsulated in nitrogen-doped porous carbon materials (Fe@N-C) from functionalized metal-organic frameworks (MOFs, MET-6). Embedding Fe nanoparticles into the carbon skeleton increases the graphitization degree and the proportion of graphitic N as well as promotes the formation of mesopores in the catalyst. The Fe@N-C-30 catalyst showed the excellent ORR activity in alkaline solutions (E₀ = 0.97 V vs. RHE, E_{1/2 …}

P-Doped Ru-Pt Alloy Catalyst Toward High Performance Alkaline Hydrogen Evolution Reaction, Rong-Qin Huang, Wei-Ping Liao, Meng-Xuan Yan, Shi Liu, Yuan-Ming Li, Xiong-Wu Kang

Journal of Electrochemistry

Electrocatalytic water splitting represents grand promise for hydrogen fuel in modern energy equipment, and the design and fabrication of higher performance catalysts are at the central. Herein, we report the sequential phosphorus (P)-doping into ruthenium (Ru) nanoparticles (Ru-P/C) by thermal annealing of Ru nanoparticles in phosphine (PH₃) atmosphere and deposition of extremely low concentration of platinum (Pt) to obtain P-doped Ru-Pt alloy catalyst supported on carbon nanotubes (CNTs), which is denoted as (Ru-P)#Pt/C. The data by X-ray diffraction spectroscopy and transmission electron microscopy show that the Ru nanoparticles existed in the form of hexagonal close-packed (hcp) phase with …

Bimetallic Compound Catalysts With Multiple Active Centers For Accelerated Polysulfide Conversion In Li-S Batteries, Wu-Xing Hua, Jing-Yi Xia, Zhong-Hao Hu, Huan Li, Wei Lv, Quan-Hong Yang

Journal of Electrochemistry

Practical applications of lithium-sulfur (Li-S) batteries are hindered mainly by the low sulfur utilization and severe capacity fading derived from the polysulfide shuttling. Catalysis is an effective remedy to those problems by promoting the conversion of polysulfides to reduce their accumulation in the electrolyte, which needs the catalyst to have efficient adsorption ability to soluble polysulfides and high activity for their conversion. In this work, we have proposed a bimetallic compound of NiCo₂S₄ anchored onto sulfur-doped graphene (NCS@SG) to fabricate a catalytic interlayer for Li-S batteries. Compared to CoS, the NiCo₂S₄ demonstrated much higher …

Research Of Three-Phases Current’S Transducers Of Filter-Compensation Devices For Control Reactive Power’S Consumption Of Asynchronous Motor, Ilkhomjon Khakimovich Siddikov, Dilyorbek Karimjonov Doniyorbek O'G'Li -, Abdumutal Abdikarimovich Abdigapirov

Chemical Technology, Control and Management

In the article given materials of developing of three-phase electromagnetic current transducers of reactive power, using with asynchronous motor, methods connecting of two sensing element, series, parallel and differential and loops suitable for each phase, dynamic characteristics of output signals of three-phase electromagnetic current transducers asynchronous motor.

On the basis of modern calculation and design complexes are of great importance in the research variable sizes of three-phase current electromagnetic transducers of filter-compensation devices of reactive power of asynchronous motors. Presented mathematical model of research of electrical, electromagnetic and magnetic elements of electromagnetic current transducers in the …

Preface To Special Issue On Electrocatalysis And Electrosynthesis, Fang-Yi Cheng, Shuang-Yin Wang, Tian-Hua Zhou

Journal of Electrochemistry

No abstract provided.

Advances And Challenges On Cathode Catalysts For Lithium-Oxygen Batteries, Bo Wen, Zhuo Zhu, Fu-Jun Li

Journal of Electrochemistry

Aprotic lithium-oxygen batteries (LOBs) with high theoretical energy density have received considerable attention over the past years. However, the oxygen reduction reaction (ORR)/oxygen evolution reaction (OER) at cathodes suffer from slow kinetics for large overvoltages in LOBs. Significant advances on catalysts have been achieved to accelerate cathode kinetics, but understanding on the formation/decomposition processes of Li₂O₂ is limited. Herein, this review highlights the fundamental understanding of the correlation between catalysts and formation/decomposition of Li2O2. Various types of cathode catalysts are discussed to reveal the mechanism of formation/decomposition of Li₂O₂, aiming to present the …

Recent Advances In Anode Materials Of Solid Oxide Electrolysis Cells, Geng Zou, Wei-Cheng Feng, Yue-Feng Song, Guo-Xiong Wang

Journal of Electrochemistry

Solid oxide electrolysis cell (SOEC) as an electrochemical energy conversion device has attracted increasing attention due to its large current density, high Faradaic efficiency and energy efficiency. Oxygen evolution reaction at the anode, a four-electron transfer process, is an important half-reaction for SOEC, which contributes to the main polarization resistance and consumes most electric energy during the electrolysis process. Hence, designing anode materials with high activity and stability is crucial for the performance improvement and practical application of SOEC. Recently, some advances have been made in the development of high-performance anode. In the current review, the mechanisms for CO_{2 …}

Anodic Electrocatalysis Of Glycerol Oxidation For Hybrid Alkali/Acid Electrolytic Hydrogen Generation, Xin Feng, Bo-Wen Liu, Ke-Xin Guo, Lin-Feng Fan, Gen-Xiang Wang, Su-Qin Ci, Zhen-Hai Wen

Journal of Electrochemistry

Electrolytic hydrogen production is heavily restricted by high-energy consumption majorly due to the relatively high potential of anodic oxygen evolution reaction (OER). Development of OER-alternative reaction at the anode has been recently proposed as a promising pathway to address the associated issues. In this work, we report a hybrid acid/alkali dual-electrolyte electrolyzer by coupling acidic hydrogen evolution reaction (HER) using commercial Pt/C cathode with alkaline Electrocatalytic glycerol oxidation (GOR) which is implemented by developing a nickel foam (NF) supporting Co₃O₄ nanosheets anode that shows low overpotential and high selectivity toward GOR for formate production. The hybrid acid/alkali …

Highly Dispersed Pt Nanoparticles Root In Single-Atom Fe Sites In Ldhs Toward Efficient Methanol Oxidation, Qing-Cheng Meng, Lin-Bo Jin, Meng-Ze Ma, Xue-Qing Gao, Ai-Bing Chen, Dao-Jin Zhou, Xiao-Ming Sun

Journal of Electrochemistry

Active and durable electrocatalysts for methanol oxidation reaction are of critical importance to the commercial viability of direct methanol fuel cell, which has already attracted growing popularities. However, current methanol oxidation electrocatalysts fall far short of expectations and suffer from excessive use of noble metal, mediocre activity, and rapid decay. Here we report the Pt anchored on NiFe-LDHs surface hybrid for stable methanol oxidation in alkaline media. Based on the high intrinsic methanol oxidation activity of Pt nanoparticles, the substrates NiFe-LDHs further enhanced anti-poisoning ability and maintained unaffected stability after 200,000 s cycle test compared to commercial Pt/C catalyst. The …

Preface To Special Issue: Electrocatalysis And Electrosynthesis (Ⅰ), Fang-Yi Cheng, Shuang-Yin Wang, Tian-Hua Zhou

Journal of Electrochemistry

No abstract provided.

Supperlattice-Like Structure: Ordered Mass Transfer Endowing High Quality Output Of Fuel Cell, Jian Wang, Wen-Hui Xuan, Qian He, Jing-Xia Jiang, Yuan-Yuan Zhou, Yao Nie, Qiang Liao, Min-Hua Shao, Wei Ding, Zi-Dong Wei

Journal of Electrochemistry

The current or voltage fluctuation in fuel cell operation is harmful to the fuel cell system and power application equipment. Here, we report a technique to eliminate such a fluctuation by the aid of new type of catalysts, superlattice-like mesoporous PtCo catalysts. The current fluctuation in fuel cells catalyzed by two invented catalysts are fixed at as low as 25 mA·cm⁻² with a power of 0.75 W·cm⁻² or 120 mA·cm⁻² with a power of 1.01 W·cm⁻², and no noticeable current decay was detected over 100 h. By contrast, a …

Recent Advances In Exploring Highly Active & Durable Pgm-Free Oxygen Reduction Catalysts, Yuan Li, Miao-Ying Chen, Bang-An Lu, Jia-Nan Zhang

Journal of Electrochemistry

In order to reduce the considerable usage of expensive but scarce platinum at the cathode in proton exchange membrane fuel cells (PEMFCs), it is necessary to pursue alternatives to platinum. The most promising platinum group metal (PGM)-free catalysts for oxygen reduction reaction (ORR) are atomically dispersed, and nitrogen-coordinated metal site catalysts denoted as M-N-C (M = Fe, Co, or Mn, etc.). Over the last few decades, there have been great advances in these catalysts with high ORR activity and promising initial fuel cell performance approaching traditional Pt/C catalysts. However, the stability of these highly active Fe-N-C catalysts under practical fuel …

Electrochemical Oxidation Of Ethylene On Palladium Electrode, Wei-Xing Wu, Ying Wang

Journal of Electrochemistry

The electrochemical oxidation of C₂H₄ is attracting increasing attention due to its vast potential market. The current electrochemical methods rely on the use of redox mediators, which may produce corrosive intermediates, while direct oxidation is still limited by its low activity and selectivity. Herein, we conducted electrochemical studies to obtain mechanistic insights into the benchmark Pd catalyst. The generated Pd(II) could be the active site for C₂H₄ oxidation. By designing the pulse sequence, we found the ratio of strongly and weakly adsorbed C₂H₄ on Pd to be 0.3:1. The result we …

Influence Of Synthesis Conditions On The Physicochemical And Electrocatalytic Properties Of Non-Stoichiometric Ba2sr2la2ti4o12 Perovskites, Ofeliya Kostadinova, Iliyan Popov, Simeon M. Stankov, Hristo Kolev, Tamara Petkov

Karbala International Journal of Modern Science

Present work studies the influence of the pretreatment milling media (deionized water (BLTOS-H) and isopropanol (BLTOS-i)) on the surface characteristics, structure, chemical composition and catalytic activity of non-stoichiometric Ba2Sr2La2Ti4O12 perovskites. The IR spectroscopy and XRD analyses shows a difference in the structure and phase composition of the two materials. X-ray photoelectron spectroscopy detects a Ba2+- and La3+-enriched and Sr2+-depleted surface. The BLTOS-i sample appears to exhibit higher specific surface area (SSA) and pore volume in comparison to BLTOS-H. The electrochemical tests showed that BLTOS-H sample have similar behavior to platinum at current densi-ties up to 10 mA cm-2, while BLTOS-i …

Evaluating The Impact Of Increased Cycling On Thermal Power Plants Due To Wind Energy Penetration In The Midwest: A Case Study, Joscelyne Larson

Electronic Theses and Dissertations

One of the most significant shifts in the mix of U.S. electricity generation over the past few years has been the rapid expansion of renewable energy resources, especially solar and wind. However, fossil fuels are still necessary to fulfill the world’s energy requirements. Despite efforts to increase the use of renewable energy sources, these sources can be at times unreliable, causing countries around the world to continue to rely on base load units such as coal and natural gas. This decrease in fossil fuels and increase in renewable energy sources presents many complex issues in terms of power system planning, …

Running Shoe Pedometer, Benjamin Kasper

Williams Honors College, Honors Research Projects

Running shoe pedometer aims to solve the issue of worn out running shoes. It can be difficult to know just how many miles you have run in your shoes and when a new pair is needed. Running in old shoes and worn out shoes is heavily linked to injury. My proposed project is a device that is powered by the compressive forces on the shoes soles that counts the number of steps the wearer takes using a microcontroller. Then, when the shoe reaches milestone that indicate it has been used 75% 90% and 100% of its expected life, it will …