Power and Energy Commons^™

Multi-Objective Optimization Of Energy Costs And Ev Battery Health In V2g Enabled Homes, Dzifa M. Hodey

Theses and Dissertations--Computer Science

Electric vehicles (EVs) and rooftop solar photovoltaic (PV) systems are increasingly being integrated into residential settings, creating new opportunities for vehicle-to-grid (V2G) and vehicle-to-home (V2H) operations. In these systems, the EV battery functions as a controllable energy storage unit that can charge from the grid or PV and discharge energy to supply household load or export to the grid for a profit. By intelligently scheduling this bidirectional power exchange, households can reduce electricity costs and enhance PV utilization. Realizing these benefits requires optimization strategies that balance cost reduction with EV battery health preservation. However, existing V2G/V2H studies largely emphasize cost …

Analytical And Semi-Analytical Modeling Of Solar Cells Using The Lambert W Function: A Comprehensive Review Of Equivalent Circuits, Adel El-Shahat, Martin Ćalasan, Snežana Vujoševic, Shady H. E. Abdel Aleem

Engineering Technology Faculty Publications

The modeling of photovoltaic (PV) cells through equivalent circuits forms a central element in the analysis, simulation, and optimization of solar energy systems. Traditional approaches often depend on iterative numerical methods to solve the implicit current–voltage (I–V) equations. In contrast, the Lambert W function has emerged as an effective mathematical tool that enables closed-form or semi-analytical expressions for a wide range of PV models. This paper presents a Lambert W-centered review of analytical and semi-analytical formulations for PV equivalent-circuit models, covering classical single-diode and multi-diode structures and modern variants incorporating additional elements, voltage-dependent parameters, and topology rearrangements. The models are …

Multi-Objective Optimization Strategy For Component Sizing In Solar-Hydrogen Microgrids Using An Advanced Hybrid Genetic Algorithm, Dylan Jones

UNF Graduate Theses and Dissertations

This thesis presents the development of a genetic algorithm (GA) optimization framework for the design and component sizing of hybrid solar-hydrogen microgrids. The framework addresses a critical gap in research and existing commercial tools by unifying performance maximization and cost minimization objectives across both grid-tied and islanded configurations. Integrating solar photovoltaics, electrolyzers, hydrogen storage, fuel cells, and batteries, the GA employs adaptive weighting and dynamic boundary constraints to balance technical feasibility with economic efficiency. To ensure real-world viability, the algorithm relies on a novel Daylight Sun Factor (DSF) for localized solar assessment and was rigorously validated against multi-year, high-fidelity irradiance …

Design And Optimization Of High-Frequency Medium-Voltage Dual Active Bridge Dc/Dc Converter Using Sic Device, Hui Cao

Graduate Theses and Dissertations

High frequency Dual Active Bridge (DAB) converters have become a key enabling technology in medium- and high-power applications such as renewable energy integration, electric vehicle fast charging, and emerging DC power distribution systems. However, when operating at high power and high frequency, DAB converters face critical challenges including limited soft-switching range, uneven semiconductor loss distribution, deadtime-induced resonance, switching-frequency constraints of wide-bandgap (WBG) devices, and transformer DC bias during dynamic transitions. This dissertation addresses these challenges through advancements in modulation strategies and converter architecture. First, an enhanced triple-phase-shift (E-TPS) modulation scheme is proposed to achieve balanced switching and conduction losses across …

Artificial Intelligence Applications For Grid-Connected Solar Inverters, Utkirjon Ubaydullaev, Sarvinoz Mirzaeva, Hasan Mustafoev

Chemical Technology, Control and Management

The increasing global demand for renewable energy has highlighted the importance of grid-connected solar inverters in ensuring efficient and stable power conversion. However, challenges such as fluctuations in solar energy generation, grid disturbances, and power quality issues necessitate advanced control strategies. The integration of artificial intelligence (AI) into solar inverters presents a transformative solution, enhancing performance, adaptability, and reliability in real-world applications.

This review explores the role of AI techniques, including machine learning (ML), deep learning (DL), fuzzy logic, and reinforcement learning (RL), in optimizing key inverter functionalities such as maximum power point tracking (MPPT), fault detection, power quality enhancement, …

Lagrange Multipliers As A Metric For Early-Stage Shipboard Power System Design, Magdalen A. Barnes

Theses and Dissertations--Electrical and Computer Engineering

Integrated power systems are essential in the operation of electric ships and must function under a diverse range of conditions. In addition to routine operation, ships should be prepared to respond to challenging events that require significant amounts of power. Demanding scenarios, coupled with complex and interconnected power systems, present challenging issues. The power and energy ratings of equipment are crucial factors in the operational success of the ship; however, to meet economic constraints, balance between performance and cost must be upheld. Details regarding equipment models and specifications are typically unavailable during early-stage design. Power system modeling and simulation can …

Analysis And Design Optimization Of Electric Machines With Field Intensifying Configuration, Ali Mohammadi

Theses and Dissertations--Electrical and Computer Engineering

The design and optimization of electric machines face increasing demands for efficiency, improved torque density, manufacturability, and effective utilization of materials. Meeting these demands is particularly vital in for example, electric vehicles (EVs) and renewable energy systems, where performance, reliability, and cost are critical. In this dissertation innovative field-intensifying electric machine configurations have been explored, emphasizing advanced topologies, computational modeling, and optimization techniques to advance the state of the art in electric machine design and analysis.

Electric machines with high torque density are essential for many low-speed direct-drive systems, such as wind turbines, in-wheel traction, and industrial automation. This dissertation …

Graph-Based Modeling And Optimization Of Wpt Systems For Evs, Matthew J. Hansen, Greg Droge, Abhilash Kamineni

Electrical and Computer Engineering Student Research

A model of a system of wireless power transfer (WPT) pads is developed, where each WPT pad is modeled as a node and the coupling between pads is modeled as graph edges. This modeling approach is generalized to admit primary, secondary, and booster coils, where power can flow among the pads and a pad can fill multiple roles. An excitation in one pad induces voltage and current in all neighboring pads, causing each pad to act as both a booster coil and either a transmitter or a receiver. Power flow through the entire system can be modeled with the graph …

Optimization Pump As Turbine Coupled To A Self-Excited Induction Generator Using Multi-Objective Genetic Algorithm, Emanuel J. Nyirenda

Tanzania Journal of Engineering and Technology (TJET)

As a way of accelerating the deployment of affordable and clean renewable energy generation technologies, applying a pump working as a turbine coupled to a self-excited induction generator is gaining popularity in various areas including energy recovery and micro hydro systems. However, it is currently challenging to predict the performance of the PAT-SEIG system and there is no agreed-upon rule on the selection of the appropriate system to be installed at a particular site. This paper has presented multi-objective optimization to select the best operating point of the PAT-SEIG system. The results show that the peak efficiencies for the PAT …

Power Grid Resiliency Enhancement Against Flood-Induced Hazards, Mohadese Movahednia

LSU Doctoral Dissertations

Natural disasters, such as floods, may damage power system assets and lead to widespread and long outages. The impact of flood can be alleviated by preventive actions such as installing tiger dams around power substations before the flood. In this regard, it is imperative that critical substations are identified in terms of the connected load and imposed costs to the system. This study presents a resource allocation approach for protecting power substations against flood events a day ahead of the event. First, the required information for the model is extracted. Flood probability distribution functions are used to generate several flood …

Learning–Assisted Constraint Filtering To Enhance Power System Optimization Performance, Fouad Hasan

LSU Doctoral Dissertations

Machine learning (ML) is a powerful tool that provides meaningful insights for operators to make fast and efficient decisions by analyzing data from power systems. ML techniques have great potential to assist in solving optimization problems within a shorter time frame and with less computational burden. AC optimal power flow (ACOPF), dynamic economic dispatch (D-ED), and security-constrained unit commitment (SCUC) are the three energy management optimization functions studied in this dissertation. ACOPF is solved every 5~15 minutes. Because of the nonconvex and complex nature of ACOPF, solving this problem for large systems is computationally expensive and time-consuming. Classification and regression …

Peer-To-Peer Energy Trading In Smart Residential Environment With User Behavioral Modeling, Ashutosh Timilsina

Theses and Dissertations--Computer Science

Electric power systems are transforming from a centralized unidirectional market to a decentralized open market. With this shift, the end-users have the possibility to actively participate in local energy exchanges, with or without the involvement of the main grid. Rapidly reducing prices for Renewable Energy Technologies (RETs), supported by their ease of installation and operation, with the facilitation of Electric Vehicles (EV) and Smart Grid (SG) technologies to make bidirectional flow of energy possible, has contributed to this changing landscape in the distribution side of the traditional power grid.

Trading energy among users in a decentralized fashion has been referred …

Optimal Design Of Special High Torque Density Electric Machines Based On Electromagnetic Fea, Murat G. Kesgin

Theses and Dissertations--Electrical and Computer Engineering

Electric machines with high torque density are essential for many low-speed direct-drive systems, such as wind turbines, electric vehicles, and industrial automation. Permanent magnet (PM) machines that incorporate a magnetic gearing effect are particularly useful for these applications due to their potential for achieving extremely high torque density. However, when the number of rotor polarities is increased, there is a corresponding need to increase the number of stator slots and coils proportionally. This can result in manufacturing challenges. A new topology of an axial-flux vernier-type machine of MAGNUS type has been presented to address the mentioned limitation. These machines can …

Ai-Driven Security Constrained Unit Commitment Using Predictive Modeling And Eigen Decomposition, Talha Iqbal

Graduate Theses, Dissertations, and Problem Reports (ETD)

Security Constrained Unit Commitment (SC-UC) is a complex large scale mix integer constrained optimization problem solved by Independent System Operators (ISOs) in the daily planning of the electricity markets. After receiving offers and bids, ISOs have only few hours to clear the day-ahead electricity market. It requires a lot of computational effort and a reasonable time to solve a large-scale SC-UC problem. However, exploiting the fact that a UC problem is solved several times a day with only minor changes in the system data, the computational effort can be reduced by learning from the historical data and identifying the patterns …

Products Pricing And Return Strategies For The Dual Channel Retailers, Jian Liu, Xinyue Sun, Yanyan Liu

Electrical and Computer Engineering Faculty Research & Creative Works

This paper analyzed how different return strategies and return rates affect dual-channel retailers' profits and channel pricings. Return can stimulate sales; however, the return has presented significant challenges to retailers. The return has long been studied to maximize profit and pricing; however, the different return strategies for dual-channel retailers affect channel both. This paper aimed to study whether or not dual-channel retailers should allow customers to return items in two channels and whether or not the retailer should contract with the manufacturers and pay extra fees to return products. This study indicated when the retailer should allow customers' returns to …

Hierarchical And Distributed Architecture For Large-Scale Residential Demand Response Management, Pramod Herath Mudiyanselage

All Dissertations

The implementation of smart grid brings several challenges to the power system. The ‘prosumer’ concept, proposed by the smart grid, allows small-scale ‘nano-grids’ to buy or sell electric power at their own discretion. One major problem in integrating prosumers is that they tend to follow the same pattern of generation and consumption, which is un-optimal for grid operations. One tool to optimize grid operations is demand response (DR). DR attempts to optimize by altering the power consumption patterns. DR is an integrated tool of the smart grid. FERC Order No. 2222 caters for distributed energy resources, including demand response resources, …

Recent Advances Of Wind-Solar Hybrid Renewable Energy Systems For Power Generation: A Review, Pranoy Roy, Jiangbiao He, Tiefu Zhao, Yash Veer Singh

Electrical and Computer Engineering Faculty Publications

A hybrid renewable energy source (HRES) consists of two or more renewable energy sources, such as wind turbines and photovoltaic systems, utilized together to provide increased system efficiency and improved stability in energy supply to a certain degree. The objective of this study is to present a comprehensive review of wind-solar HRES from the perspectives of power architectures, mathematical modeling, power electronic converter topologies, and design optimization algorithms. Since the uncertainty of HRES can be reduced further by including an energy storage system, this paper presents several hybrid energy storage system coupling technologies, highlighting their major advantages and disadvantages. Various …

Torque Vectoring To Maximize Straight-Line Efficiency In An All-Electric Vehicle With Independent Rear Motor Control, William Blake Brown

Theses and Dissertations

BEVs are a critical pathway towards achieving energy independence and meeting greenhouse and pollutant gas reduction goals in the current and future transportation sector [1]. Automotive manufacturers are increasingly investing in the refinement of electric vehicles as they are becoming an increasingly popular response to the global need for reduced transportation emissions. Therefore, there is a desire to extract the most fuel economy from a vehicle as possible. Some areas that manufacturers spend much effort on include minimizing the vehicle’s mass, body drag coefficient, and drag within the powertrain. When these values are defined or unchangeable, interest is driven to …

Performance Loss Rate And Temperature Modeling In Predictive Energy Yield Programs For Utility-Scale Solar Power Plants, Katelynn M. Dinius

Master's Theses

The Gold Tree Solar Farm, designed by REC Solar, has a rated output power of 4.5 MW and began operation in 2018 to provide electricity to Cal Poly’s campus. Gold Tree Solar Farm site terrain consists of rolling hills and uneven slopes. The uneven typography results in interrow shading, requiring a modified tracking control algorithm to maximize power production. Predicting a utility solar field’s lifetime energy yield is a critical step in assessing project feasibility and calculating project revenue. The MATLAB-based predictive power model developed for this field overpredicted power in the middle of the day. The purpose of this …

Zip Load Modeling For Single And Aggregate Loads And Cvr Factor Estimation, Yiqi Zhang, Yuan Liao, Evan S. Jones, Nicholas Jewell, Dan M. Ionel

Electrical and Computer Engineering Presentations

ZIP load modeling has been used in various power system applications. The aggregate load modeling is common practice in utility companies. However, little research has been done on the theoretical formulation of the aggregate load. This paper formulates the aggregate ZIP load model using the single ZIP load model. The factors that may affect aggregate ZIP load estimation are studied. Common ZIP parameter estimation methods including least squares method, optimization method and neural network method have been used in this paper to estimate ZIP parameters. The case studies are based on the IEEE 13-bus and 34-bus system built in OpenDSS. …

A Demand-Supply Matching-Based Approach For Mapping Renewable Resources Towards 100% Renewable Grids In 2050, Loiy Al-Ghussain, Adnan Darwish Ahmad, Ahmad M. Abubaker, Mohammad Abujubbeh, Abdulaziz Almalaq, Mohamed A. Mohamed

Mechanical Engineering Graduate Research

Recently, many renewable energy (RE) initiatives around the world are based on general frameworks that accommodate the regional assessment taking into account the mismatch of supply and demand with pre-set goals to reduce energy costs and harmful emissions. Hence, relying entirely on individual assessment and RE deployment scenarios may not be effective. Instead, developing a multi-faceted RE assessment framework is vital to achieving these goals. In this study, a regional RE assessment approach is presented taking into account the mismatch of supply and demand with an emphasis on Photovoltaic (PV) and wind turbine systems. The study incorporates mapping of renewable …

Multi-Objective Optimization For Aircraft Power Systems Using A Network Graph Representation, Damien Lawhorn, Vandana Rallabandi, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Today, the electrification of flight is more popular than ever, creating a wide array of concept aircraft and associated power system topologies. In order to gain insights into benefits of these varying architectures, this paper introduces the development of a framework for electric aircraft power system (EAPS) optimization. The proposed framework accepts inputs from a designer in the form of component parameters and desired flight mission characteristics. A collective graph representing many possible architectures is formed, from which, subgraphs that describe power system topologies meeting the flight requirements are extracted and analyzed. Optimal EAPS architectures with respect to goals of …

Research On Power System State Estimation Problems – Series-Compensated Transmission Line Parameter And Load Model Parameter Estimation, Yiqi Zhang

Theses and Dissertations--Electrical and Computer Engineering

Transmission line and load model parameters are essential inputs to power system modeling and simulation, control, protection, operation, optimization, and planning. These parameters usually vary over time or under different operating conditions. Thus, reliable estimation methods are desired to ensure the accuracy of those parameters. This research focuses on estimation for transmission line parameters and the ZIP load model. The proposed estimation methods can use both online measurements and historical data of a specified duration. The parameters of long transmission lines with different series-compensation configurations are estimated using linear methods and optimal estimators with bad data detection capability. Additionally, Kalman …

Voltage Security Optimization For Power Transmission Systems, Tamer Ibrahim

Dissertations and Theses

This project proposes an optimization approach for day-ahead reactive power planning to ensure voltage security in transmission networks. The problem is formulated as a voltage-secure multi-period optimal reactive power dispatch (MP-ORPD) problem. The optimization approach searches for optimal set-points of dynamic and static reactive power (var) resources. Specifically, the output includes set-points for switching shunts, transformer taps, and voltage magnitudes at the regulated buses. The primary goal is to maximize the dynamic reactive power reserve of the system, by minimizing the reactive power supplied by synchronous generators. The secondary goal is to minimize changes in the settings of switching shunts …

Design Optimization And Comparison Of Direct-Drive Outer-Rotor Srms Based On Fast Current Profile Estimation And Transient Fea, Vandana Rallabandi, Peng Han, Jie Wu, Aaron M. Cramer, Dan M. Ionel, Ping Zhou

Power and Energy Institute of Kentucky Faculty Publications

Outer-rotor switched reluctance machines (SRMs) have drawn much attention as promising candidates for in-wheel direct-drive motors of future electric vehicles. This article presents a systematic performance comparison of three outer-rotor SRM topologies for in-wheel traction applications in terms of the specific torque, electromagnetic efficiency, torque ripple, radial force, and mechanical aspects. A generalized design optimization framework for SRMs is proposed to enable the fast evaluation of large numbers of designs generated from the differential evolution by incorporating an analytical current profile estimation into the transient finite element analysis. The relationship between the saliency ratio and converter volt-ampere rating is also …

Optimal Study Of A High Specific Torque Vernier-Type Axial-Flux Pm Machine With Two Different Stators And A Single Winding, Murat G. Kesgin, Peng Han, Narges Taran, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

This paper presents the optimal study of a verniertype axial-flux permanent-magnet (AFPM) machine, which has a high-polarity spoke-type PM rotor, a wound stator with a low number of coils, and a profiled stator. Both stators have profiled teeth to enhance the magnetic interaction between the rotor PM array and stator windings for torque production. Compared to the topology with two wound stators, the studied one has a smaller total axial length and is expected more suitable for applications where the space is limited in axial direction. Both topologies are optimized through 3-dimensional (3D) finite element analysis (FEA) by the combined …

Design Optimization Of Coreless Axial-Flux Pm Machines With Litz Wire And Pcb Stator Windings, Murat G. Kesgin, Peng Han, Narges Taran, Damien Lawhorn, Donovin Lewis, Dan M. Ionel

Electrical and Computer Engineering Faculty Publications

Coreless axial-flux permanent-magnet (AFPM) machines may be attractive options for high-speed and high-power-density applications due to the elimination of core losses. In order to make full use of the advantages offered by these machines and avoid excessive eddy current losses in windings, advanced technologies for winding conductors need to be employed to suppress the eddy effect, such as the Litz wire and printed circuit board (PCB). In this paper, the best practices for designing Litz wire/PCB windings are discussed and a brief survey of state of the art PCB winding technology is provided. Three coreless AFPM machines are mainly considered. …

Cost Analysis Of Optimized Islanded Energy Systems In A Dispersed Air Base Conflict, Jay F. Pearson, Torrey J. Wagner, Justin D. Delorit

Faculty Publications

The United States Air Force has implemented a dispersed air base strategy to enhance mission effectiveness for near-peer conflicts. Asset dispersal places many smaller bases across a wide geographic area, which increases resupply requirements and logistical complexity. Hybrid energy systems reduce resupply requirements through sustainable, off-grid energy production. This paper presents a novel hybrid energy renewable delivery system (HERDS) model capable of (1) selecting the optimal hybrid energy system design that meets demand at the lowest net present cost and (2) optimizing the delivery of the selected system using existing Air Force cargo aircraft. The novelty of the model’s capabilities …

A Network Graph Technique For The Design Of Electric Aircraft Power Systems, Damien Lawhorn, Vandana Rallabandi, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Today the electrification of flight is more popular than ever, creating a wide array of concept aircraft and associated power system topologies. In order to gain insights into benefits of these varying architectures, this paper introduces the development of a framework for electric aircraft power system (EAPS) optimization. The proposed framework accepts inputs from a designer in the form of component parameters and desired flight mission characteristics. A collective graph representing many architectures is formed, from which, subgraphs or power system topologies meeting the flight requirements are extracted and analyzed. An optimum topology meeting the flight requirements with minimum mass, …

Meeting Temporary Facility Energy Demand With Climate-Optimized Off-Grid Energy Systems, Jay F. Pearson, Torrey J. Wagner, Justin D. Delorit, Steven J. Schuldt

Faculty Publications

Remote and contingency operations, including military and disaster-relief activities, often require the use of temporary facilities powered by inefficient diesel generators that are expensive to operate and maintain. Site planners can reduce operating costs by increasing shelter insulation and augmenting generators with photovoltaic-battery hybrid energy systems, but they must select the optimal design configuration based on the region’s climate to meet the power demand at the lowest cost. To assist planners, this paper proposes an innovative, climate-optimized, hybrid energy system selection model capable of selecting the facility insulation type, solar array size, and battery backup system to minimize the annual …