Power and Energy Commons^™

Design And Evaluation Of An Open-Source Ac/Dc Power Converter For Microgrid Applications, Ryan J. Rayos

Master's Theses

This thesis presents the design, implementation, and evaluation of an open-source bidirectional power conversion platform intended for microgrid applications. As distributed energy resources, battery storage systems, and hybrid AC/DC architectures continue to increase in adoption, there is a growing demand for flexible, low-cost, and programmable power electronic platforms capable of interfacing between DC and AC subsystems. Existing commercial solutions are often proprietary and expensive, limiting their accessibility for educational, research, and rapid prototyping applications. This work expands upon the existing open-source Atinverter platform by increasing its operating voltage capability, integrating bidirectional power flow, and implementing telemetry systems suitable for microgrid …

Performance Comparison Of A Two-Level And A Three-Level 1500v Three-Phase Grid-Tied Solar Inverter, Shawn Sproles

Electrical Engineering and Computer Science Undergraduate Honors Theses

With the global switch to renewable energy sources, photovoltaic energy has become an integral source to harvest from. When solar panels convert sunlight into a DC voltage, a grid-tied inverter is needed to transform this DC voltage into an AC voltage to interface with the AC grid. The most widely used topologies for grid-tied solar inverters are two-level three-phase inverters and three-level NPC three-phase inverters. Compared to two-level inverters, three-level NPC inverters have advantages such as lower EMI, lower THD, and lower switching losses. Moreover, three-level NPC inverters are shown to have higher efficiency in low-voltage applications at medium to …

Investigating The Harmonic Content Of A Pwm Inverter With Varying Modulation Index, Peter Makolo

Tanzania Journal of Engineering and Technology (TJET)

Photovoltaic energy is a clean and endless vital renewable energy. In order to generate electricity from solar energy an inverter is required to transform the direct current into alternating current. Also, with the emerging of new ultra-high voltage direct current transmission technology, the rectification and inverters play a great role. Most three-phase two-level inverters draw harmonics that cause heat dissipation, waveform distortions hence affect the electrical loads. Knowing that Total Harmonic Distortion content of voltage source inverter is important and must be within the allowable range. Several schemes are suggested to mitigate the distortion in order to produce as much …

Development Of A Versatile Switching Mode Inverter Laboratory Module, Zachariah Lee Mustar

Master's Theses

DC-AC converters, or inverters, are complex devices that play an essential role in photovoltaic, energy storage, and microgrid systems. Therefore, they constitute a class of power electronics that any power-focused electrical engineering student should be familiar with. This thesis presents the development and testing of a single device that power electronics students will use in a laboratory setting to experiment with each of the four different switching techniques employed in inverters: a simple square wave (SSWI), modified square wave (MSWI), bipolar PWM, and unipolar PWM. The module was built with a physically modifiable control stage and a power stage constituting …

Investigation And Characterization Of Silicon Carbide Power Mosfets, Vincent Hassman

Electrical Engineering and Computer Science Undergraduate Honors Theses

As engineers constantly seek to make solar power systems smaller, cheaper, and more efficient, technological enhancements in the electronics that run them are required. One of the most fundamental electronic components of any solar system is the inverter, which takes DC current from the solar cell and turns it into AC current that is supported by the grid. This is done with metal oxide semiconductor field effect transistors (MOSFETs). Through more advanced MOSFET technology, inverters can switch at a higher frequency, increasing efficiency and reducing size and cost.

MOSFET performance can be enhanced by swapping the traditional silicon substrate with …

Dc To Ac Voltage Source Converter Control System, Mohummad Tark Elgassier, Jordan M. Reichhardt, Brayden Richard Young

Electrical Engineering

The Voltage Source Converter Control System integrates a control system for a 2-phase half-bridge voltage source converter (VSC) utilizing a TMS320F2837xD Dual-Core Real-Time Microcontroller. VSCs are critical for the integration of power production into the power grid. They allow for accurate control over DC-AC energy conversion. Additionally with the improvement of renewable energies VSCs play a critical role in controlling the flow of these environmentally controlled and more unpredictable sources of energy. The control system regulates the output current and voltage, regulates switching patterns, and maintains power stability under varying loads. Within the control system Digital control systems, PWM generation, …

Short-Circuit Modeling And Instantaneous Overvoltage Protection Of Renewable Farms, Shah Mohazzem Hossain

All Dissertations

The existing utility grid is experiencing a paradigm shift in electricity generation due to a significant penetration of renewable energy sources. This shift is primarily driven by the large-scale integration of solar and wind energy farms, particularly in the transmission network, where these farms are typically accompanied by battery energy storage in a hybrid configuration to overcome source intermittency and improve reliability. Such renewable farms comprise numerous inverters, pad-mounted transformers, collector feeders, and dc-side components depending on the generation-source type. Additionally, inverters within these farms exhibit distinct operating modes, such as `grid-following'(GFL) and `grid-forming'(GFM), as well as fault control modes, …

Battery Energy Storage System, Alec C. Maclean, Kaylen H. Schwartz, Kyle A. Begley

Electrical Engineering

The project is a continuation of part 1 of the “Reliability Measurement for Grid-Connected Solar System” project. The goal is to continue where the previous design failed. This project will configure an ITECH IT-6000C and Tabuchi Battery Energy Storage System (BESS) to the small-scale microgrid at the Cal Poly, San Luis Obispo EE Department. Initially, a system was designed to connect an ITECH IT-M3633 as a PV solar source emulator to the Tabuchi BESS within a grid-connected microgrid system in Room 20-102 at Cal Poly. A Photovoltaic Thevenin equivalent model was developed for the ITECH IT-M3633, but this setup failed …

Improving The Power Efficiency Of Woodward’S High-Power Inverter (Hpi) Using Algorithmic Part Selection., Jaron Holder, Ali Al Gazwi, John Childers, Jose Soublett

Honors Capstones

Woodward Inc. is a secondary aerospace manufacturer based in the USA that specializes in aircraft power and control systems. This senior design project was concerned with a power systems platform currently in development by Woodward, the High-Power Inverter (HPI) system. In this report, the senior design group from Northern Illinois University (NIU) demonstrated the creation of an algorithmic part selection process to choose more power-efficient electrical components, the prototyping using MATLAB Simulink, and the practical testing that showed an increase of 7% in the power efficiency of the HPI system.

Dc To Ac Inverter For A Microgrid-Inspired Power Distribution Architecture For Electric Vehicles, Bryan A. Carrillo Martinez, Eli Blacklock, Paul A. Samson, William S. Holt-Hillis

Electrical Engineering

This project builds upon the prototyping of a microgrid-inspired power distribution architecture for electric vehicles (EVs). The efficacy of this prototype aims to inform a full-scale power distribution system that charges an EV battery, supports the electric grid with important ancillary services, performs peer-to-peer EV charging, and works in conjunction with other AC and DC sources and loads. The scope of this report focuses specifically on the design, construction, and testing of the DC/AC inverter. Future development of this distribution architecture will incorporate synchronous generators, a battery management system, and an Arduino/Raspberry Pi-based communication system to fully simulate an electric …

Designing A Model Of Solar Photovoltaic Water Pumping System For Off-Grid Localities In Tanzania, Imani Mruma

Tanzania Journal of Engineering and Technology (TJET)

Modeling of photovoltaic (PV) water pumping system for rural water localities is vital especially in these modern days, in Tanzania. This is due to the rise of high number of solar-powered rural water projects constructed lacking appropriate design. The fate result into poor and substandard projects delivering below expectations. Kikombo Solar Water Project situated in Dodoma; Tanzania is one among poorly designed solar project chosen as a case study to validate proposed model. The main problem of Kikombo project is unsatisfactory amount of water from domestic points to satisfy population demand. This matter has been raised by pumping-station attendants and …

Design Of Hybrid Inverters Using Wideband Gap Semiconductors For Microgrid Application, Luca Gacy

Electronic Theses and Dissertations

As the world becomes more reliant on renewable energy sources such as solar and wind power, the need for high efficiency high power inverters connected to homes is more relevant than ever. Connecting these renewable energy sources (RES) coupled with an energy storage system (ESS) to the grid through a hybrid inverter, with the highest efficiency and grid stability, is quickly becoming a necessity for the near future. This thesis explores the integration of wide band gap semiconductors for the power stage in these systems, along with the analysis of hybrid inverter topologies and structures. The goal of this thesis …

Controller Platform Design And Demonstration For An Electric Aircraft Propulsion Driv, Rosten Sweeting

Graduate Theses and Dissertations

With the growth in the aerospace industry there has been a trend to optimize the performance of an aircraft by reducing fuel consumption and operational cost. Recent advancements in the field of power electronics have pushed towards the concepts of hybrid electric aircraft also known as more electrical aircrafts. In this work, a custom controller board for an electric aircraft propulsion drive was designed to drive a permanent magnet synchronous motor. Design of the controller board required knowledge of the topology selection and power module selections. Simulations of the system were performed using MATLAB/Simulink to analyze the overall performance of …

Design And Analysis Of A Single-Stage Inverter Using Parallel Dc-Dc Converters For Solar Cell Application, Gabriel Leonides

Master's Theses

This thesis introduces the design and analysis of a single-stage inverter. A circuit was designed and simulated as a proof of concept to investigate the possibility of using boost and buck-boost converters to provide an AC output. The proposed circuit utilizes non-synchronous boost and buck-boost converters due to their simplicity in control signals as opposed to synchronous converters. The application of the proposed inverter is for use with individual solar cells. The aim of the inverter for a single cell is to improve the efficiency of a solar panel, whose performance is limited to the performance of the least efficient …

Improvement Of Stability Of A Grid-Connected Inverter With An Lcl Filter By Robust Strong Active Damping And Model Predictive Control, Seungyong Lee

Graduate Theses and Dissertations

This study addresses development and implementation of robust control methods for a three-phase grid-connected voltage source inverter (VSI) accompanied by an inductive-capacitive-inductive (LCL) filter. A challenge of current control for the VSI is LCL filter resonance near to the control stability boundary, which interacts with the inverter control switching actions and creates the possibility of instability. In general, active damping is needed to stabilize the system and ensure robust performance in steady-state and dynamic responses. While many active damping methods have been proposed to resolve this issue, capacitor-current-feedback active damping has been most widely used for its simple implementation.

There …

Performance And Economics Of Solar Inverters And Module Level Power Electronics In A 1 Mw Photovoltaic System, Maxwell Criswell

Biological and Agricultural Engineering Undergraduate Honors Theses

Photovoltaic solar panels convert sunlight to electricity in the form of direct current; therefore, a necessary component of every photovoltaic system is an inverter to convert the electricity to usable alternating current. There are various commercially available inverter technologies manufactured today such as microinverters, string inverters, and central inverters, as well as module level power electronic devices such as DC optimizers that are capable of improving system performance in string and central inverter systems. This thesis compares the performance and economics of five different inverter and module level power electronic systems through model simulation using Helioscope software. The five alternatives …

Trust-Based User Interface Design For Islanded Alternating Current Microgrids, Yuliya Matlashova

Electrical and Computer Engineering ETDs

Futuristic microgrid systems may be capable of providing extensive information to the operator. As microgrid systems become more pervasive there will be a need to adjust the information an operator requires, to provide an optimized user-interface. In this paper, a combinatorial optimization strategy is used to provide an optimal user-interface for the microgrid operator that selects information for display depending on the operator's trust level in the system, and the assigned task. We employ a method based in sensor placement by capturing elements of the interface as different sensors, that find an optimal set of sensors via combinatorial optimization. However, …

Design And Optimization Of A High Power Density Silicon Carbide Traction Inverter, Tyler Adamson

Graduate Theses and Dissertations

This project was initiated with the goal of demonstrating a 3-phase silicon carbide based 150-kW 25 kW/L DC-AC power conversion unit capable of operation with coolant temperatures up to 90°C. The project goals were met and exceeded by first analyzing the established inverter topologies to find which one would yield the highest power density while still meeting electrical performance needs in the 150-kW range. Following topology selection, the smallest silicon carbide power module that met the electrical requirements of the system was found through experimental testing and simulation. After a power module selection was finalized, a DC link capacitor bank …

Incorporating Battery Energy Storage Systems Into Multi-Mw Grid Connected Pv Systems, Vandana Rallabandi, Oluwaseun M. Akeyo, Nicholas Jewell, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

This paper analyzes the configuration, design, and operation of multi-MW grid connected solar photovoltaic (PV) systems with practical test cases provided by a 10-MW field development. In order to improve the capacity factor, the PV system operates at its maximum power point during periods of lower irradiance, and the power output is limited to a rated value at high irradiance. The proposed configuration also incorporates a utility scale battery energy storage system (BESS) connected to the grid through an independent inverter and benefits of the experience gained with a 1-MW 2-MWh BESS large demonstrator. The BESS power smoothing and frequency …

Optimization Of Pv Powered Spd Switchable Glazing To Minimise Probability Of Loss Of Power Supply, Aritra Ghosh, Brian Norton

Articles

Suspended particle device (SPD) glazing is an electrically actuated switchable glazing. It requires alternate current (AC) power supply to switch from opaque to transparent state. To power this glazing using PV device requires inverter. Optimization of AC powered switchable SPD glazing using photovoltaic (PV) device has been evaluated using loss of power supply probability (LPSP). Electrically switchable direct current (DC) powered electrochromic glazing was also considered in this investigation as it doesn't need any inverter to couple with PV. It is concluded that behaviour of these glazings is the dominant factor in performance optimization outweighting than azimuthal orientation and inclination …

Simulation Studies For A Multi-Mw Hybrid Wind-Solar Pv System For Desalination Plants, Vandana Rallabandi, Nasser Alawhali, Oluwaseun M. Akeyo, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

This paper presents a power system configuration and control schemes for a Multi-MW wind-solar hybrid system, which includes multiple wind turbines and solar panels to support a desalination plant. The wind and solar systems are sized such that the desalination plant obtains, as far as possible, its power from the renewable sources, to minimize the dependence on the utility grid. Each section of the wind turbine system includes a variable speed permanent magnet synchronous generator connected to the grid via a back-to-back voltage source converter. The rectifier operates the wind system at the maximum power point, and the inverter provides …

Analysis And Simulation Of Photovoltaic Systems Incorporating Battery Energy Storage, Oluwaseun M. Akeyo

Theses and Dissertations--Electrical and Computer Engineering

Solar energy is an abundant renewable source, which is expected to play an increasing role in the grid's future infrastructure for distributed generation. The research described in the thesis focuses on the analysis of integrating multi-megawatt photovoltaics (PV) systems with battery energy storage into the existing grid and on the theory supporting the electrical operation of components and systems. The PV system is divided into several sections, each having its own DC-DC converter for maximum power point tracking and a two-level grid connected inverter with different control strategies. The functions of the battery are explored by connecting it to the …

Improvements In Inverter Modeling And Control, Xiao Liu

Theses and Dissertations--Electrical and Computer Engineering

In this dissertation, the generalized averaging method models for inverters, reactive power control methods for photovoltaic inverters, and a noise immunity improvement for hybrid position observers for brushless dc motor drives are studied.

Models of inverters and other converters based on averaging have been widely used in numerous simulation applications. Generalized averaging can be applied to model both average and switching behavior of converters while retaining the faster run times associated with average-value models. Herein, generalized average models for single- and three-phase pulse width modulation inverters are proposed. The modulation signal for the proposed model could be either a sinusoidal …

Solar Generation's Impact On Fault Current, Kody Heppner

Electrical Engineering

California is paving the road for other states with the capacity of solar installations for residential and commercial entities. The added capacity of solar generation to the state's electric grid has an impact on power flow and fault currents. This project looks at the impact of solar installations on fault currents. Feeders with added residential rooftop solar and larger commercial solar installations may impact the system differently than a large, utility-sized solar installation. This project looks at the impact of both cases on the magnitude of fault current during many different fault types and locations that can occur within a …

Solar-Powered Hot Tub, Jonathan Peterson, Anthony Zepeda

Electrical Engineering

This paper discusses the design and implementation of a solar-powered hot tub. The concept of this project was to design an independently-operated hot tub powered by a 12V rechargeable battery, charged during the day by a single 400W solar panel. For this purpose, a twenty-year-old name-brand hot tub was purchased, in used condition. The plumbing, AC electrical wiring, and mechanical pumps were all removed and replaced with new components to meet our design specifications. Additionally, a solar water-heater was designed and integrated into the system to directly apply the sun’s heat to water pumped in and out of the tub, …

Grid-Tie Arrangements For Micro-Generation Under En50438; An Irish Evaluation, Liam Murphy

Conference papers

This paper explores the significance of EN50438 as the standard governing the grid-connection of micro-generation to the distribution network. In the context of micro-generation, EN50438 therefore governs the inverter requirement associated with the majority of micro-generation. Another consideration presented in this research is findings and analysis related to the manufacturers stated efficiency of a grid-tied inverter connected to a Photovoltaic (PV) array in Dublin City Centre, Ireland.

Design And Simulation Of V2g Bidirectional Inverter And Dc-Dc Converter, Allan Agatep, Mason Ung

Electrical Engineering

As plug-in hybrid electric vehicles (PHEV) become more popular, the utility companies are forced to feed the grid more electricity. However, these PHEVs are capable of providing power to the grid when they are parked serving as ancillary systems for grid regulation (V2G). Using a system based on photovoltaic (PV) technology, a design for a bidirectional inverter with LCL filter, and a bidirectional dc-dc with a constant current controller, was constructed using LTspice. Various papers were researched and analyzed to determine applicable designs for components. Simulations show the designs are capable of bidirectional power transfer. ETAP simulations show that delivering …

High Voltage Switched-Mode Power Supply For Three-Phase Ac Aircraft Systems, John Brewer Jr., Kamaljit Bagha

Electrical Engineering

The purpose of this senior project was to design and fabricate a proof-of-concept Three-Phase Sinusoidal Switched-Mode Inverter with a power output capability of 10 kW and nominal operating frequency of 400 Hz for AC aircraft system applications. This senior project report includes a thorough discussion and presentation of the inverter system background, requirements, design, construction, and testing processes.