Construction Engineering and Management Commons^™

Dynamic Response Analysis Of Bridge Under Combined Action Of Random Traffic Flow And Wind Based On Simpack Platform, Xiong Tao, Han Yan, Ma Xingchuan, Li Qianming, Yan Naijie, Zhang Fei, Hu Peng

Journal of China & Foreign Highway

To deal with the time-consuming problem of calculating the dynamic responses of the bridge under the combined action of random traffic flow and wind，a steel box continuous girder bridge was taken as the engineering background，and the finite element model of the bridge and the vehicle model were established in the commercial software Ansys and SIMPACK，respectively.Then，the dynamic responses of the bridge subjected to the single vehicle load，wind loads，and multiple vehicle loads were calculated to verify the superposability of the dynamic responses of the bridge.On this basis，the Monte Carlo method was used to generate the random traffic flow samples.By using the verified …

Research Progress Of Rubber‑Modified Asphalt By Wet Process, Ge Dongdong, Jiang Xiangyang, Lyu Songtao, Zhang Honggang, Song Xiaojin

Journal of China & Foreign Highway

The application of waste tires in asphalt pavements can not only effectively reduce resource consumption but also significantly reduce environmental pollution.Crumb rubber could be obtained by processing waste tires and used as a modifier by mixing with asphalt through the wet process to improve the performance of asphalt.This paper reviewed the research progress of rubber-modified asphalt by wet process and discussed its preparation process，influencing factors of performance，and modification mechanism.By reviewing the relevant studies，the critical conditions in the preparation process and their effects on storage stability were summarized.Furthermore，the effects of rubber dosage，particle size，matrix asphalt type，and preparation parameters on the physical and …

Skid Resistance Detection Technology Of Highway Pavement Based On Tie‑Pavement Coupling Noise, Ye Wei, Chen Fei, Hu Xiaoyang, Xu Zhengwei, Li Liguo

Journal of China & Foreign Highway

In order to improve the skid resistance detection technology of highway pavement，this paper summarized the advantages and disadvantages of the traditional pavement noise measurement methods，adopted the vehicle-following method to collect the tie-pavement coupling noise，and optimized the specific positional parameters of the microphone.The speed correction of the equivalent continuous A-weighted sound level was realized through the fitting of driving speed and equivalent continuous A-weighted sound level.The characteristic signal of the tie-pavement coupling noise was extracted by the principal component analysis method，and it can effectively suppress interference signals such as traffic noise，wind noise，and engine noise.The envelope noise energy （ENE） was obtained by …

Effect Of Corn Stover Oil On Rheological Properties Of Aged Asphalt And Its Regeneration Effect, Cheng Peifeng, Bai Yue, Li Yiming, Zhang Zhanming

Journal of China & Foreign Highway

Corn stover oil，as a kind of bio-oil，is low-carbon and renewable.At the same time，it may restore the performance of aged asphalt.In order to further promote the application of corn stover oil in road engineering，this study explored the effect of corn stover oil as a kind of regeneration agent on the rheological properties of aged asphalt through laboratory experiments and analyzed the regeneration effect.On this basis，the regeneration mechanism of corn stover oil regeneration agent was revealed by using an infrared spectroscopy test and gel permeation chromatography test.The results show that the addition of corn stover oil changes the proportion of aged asphalt …

Research And Practice On Demolition Of Lane Separator In Same Direction Along Zhengzhou‒Luoyang Section Of Lianyungang‒Khorgos Expressway, Zhang Nan, Ji Xiang, Ma Gang

Journal of China & Foreign Highway

In order to solve the problem arising after the demolition and closure of the lane separator in the same direction along the expressway，this paper systematically introduced the reconstruction method of the lane separator in the same direction by studying the overhaul project along Zhengzhou-Luoyang section of Lianyungang‒Khorgos Expressway.The paper explored the main diseases and potential safety hazards existing in the lane separator in the same direction by checking the compliance of specifications，analyzing the traffic operation status，exploring the characteristics of traffic accidents，and investigating the traffic safety facilities.On this basis，it demonstrated the feasibility of demolishing the lane separator in the same direction.According …

Mechanical Properties Of Alkali‑Activated Slag‑Fly Ash Geopolymers, Liu Yang, Wang Jizhao, Lu Naiwei, Wang Bowen

Journal of China & Foreign Highway

In order to respond to the national strategy of energy saving and emission reduction and improve the comprehensive utilization rate of industrial waste，the influence of slag content，alkali equivalent，sodium silicate modulus，and water-cement ratio on the compressive strength of slag-fly ash geopolymers was investigated by single variable and orthogonal experiment method.The compressive strength of geopolymers was analyzed by combining XRD，SEM，and porosity.The results show that the gel formation is promoted with the increase in slag content，and the structure of geopolymers is more compact，which is conducive to the development of strength.After 28 days of standard curing，the influence of various factors on the compressive strength …

Mechanical Properties Of Geopolymer‑Stabilized Recycled Aggregates From Construction Solid Wastes, Yuan Kaixin, He Yongjian, Zhang Laijun, Li Hai, Xu Gewei

Journal of China & Foreign Highway

In order to solve the problem of a sharp increase in construction solid wastes and insufficient utilization rate，this paper took slag-fly ash-based geopolymer as an inorganic binder，replaced natural gravels with recycled aggregates from construction solid wastes，and set urban road base layer as the target scene to study the mechanical properties of geopolymer-stabilized recycled aggregates at different contents.The results show that with the increase in geopolymer content，the maximum dry density of the mixture increases.The optimum moisture content increases.The unconfined compressive strength of the mixture increases with the increase in geopolymer content and curing age and decreases with the increase in recycled …

Comparative Experimental Study On Deformation Characteristics Of High Liquid Limit Soil Under Different Dry And Wet States, Qin Lingwei, Zhang Rui, Li Lu, Xiao Yupeng

Journal of China & Foreign Highway

In order to further reveal the internal mechanism of the influence of solid-like bound water on the deformation characteristics of high liquid limit soil，the difference in the influence of different bound water contents on the deformation of soil samples was analyzed through the comparison of dry and wet sides.Four types of high liquid limit soil with different water contents at the same dry density were used，and a low liquid limit soil was used as a comparison sample to carry out a deformation test.The volumetric flask method was used to test the content of adsorbed bound water in each test soil …

Influence Of Loading Methods On Compression Modulus Of Red Sandstone Soil Solidified With Biological Enzyme And Cement, He Liang, Zhang Haixiang, Guan H Ongxin, Li Huili, Yang Hairong, Liu Hongfu

Journal of China & Foreign Highway

There are various methods to test the modulus of cement-stabilized mixtures.The stiffness performance of cement-stabilized materials will be affected after adding biological enzymes.In order to systematically analyze the influence of loading conditions on the compression modulus of the red sandstone soil solidified with biological enzyme and cement，compressive modulus tests were conducted on the red sandstone soil solidified with biological enzyme and cement by using three static modulus test methods including monotonic loading method of middle section，stepwise loading and unloading method of top surface，and stepwise loading and unloading method of middle section，as well as dynamic modulus method of top surface and …

Optimization Of Mix Proportion For New Jersey Precast Concrete Safety Barriers And Performance Tests Under Integral Concrete Vibrating, Chen Lin, Li Beian, Li Yuanrui, Zhao Zixiang

Journal of China & Foreign Highway

New Jersey safety barriers are the most commonly used form of guardrails in highway median separators due to their excellent safety protection.In response to the cost reduction and quality improvement，efficient and rapid preparation process，and quality issues of New Jersey precast concrete safety barriers，this article adopted the automation production process of New Jersey precast safety barriers，optimized concrete mix proportion for precast safety barriers，and studied their performance.The experimental results show that in the designed C 30 concrete，the compressive strength of the concrete mixed with 15% fly ash reaches 39.2 MPa，and th e slump reaches 185 mm.The concrete performance meets the requirements of …

Experimental Study On Shear Behavior Between Nrc‑Uhpc Interface, Chen Zhenkan, Li Junsheng, Shi Quan, Fang Haozhen, Mo Fan, Jiang Haibo

Journal of China & Foreign Highway

In order to investigate the effect of the screw diameter of planted bars and ultra-high performance concrete （UHPC） pouring method on the shear behavior of normal reinforced concrete （NRC） and UHPC， two groups of six push-out specimens were designed for shear behavior tests.The results show that after the failure of the concrete bonding force in the NRC-UHPC interface，the screw can maintain shear behavior so that the failure process of the specimen after the load reaches the peak shows ductile characteristics.For specimens with screw diameters of 12 mm and 16 mm，greater screw diameter indicates higher shear capacity of the specimens and …

Design And Construction Process Of Cross‑Beam Supports For Main Tower Of Changtai Changjiang River Bridge, Zeng Jian, Hu Pei, Wang Chao

Journal of China & Foreign Highway

The construction of the lower cross-beam structure of the main tower of Changtai Changjiang River Bridge has the characteristics of high construction height，large amount of concrete earth volume，and difficult control of down-warping deformation.In order to implement the pouring of the lower cross-beam of the main tower，floor-type steel pipe supports were set at the lower cross-beam，which were used to support the lower cross-beam formwork and bear the load during the concrete pouring.Through the finite element software analysis and calculation，it was found that the asymmetric deformation of the main structure of the lower cross-beam could be effectively controlled，and the overall force of …

Determination Of Manufacturing Parameters Of Large Section Of Continuous Steel Box Beam With Variable Section In Shenzhen‑Zhongshan Passage, Dong Chuangwen, Chen Long, Li Chuanxi

Journal of China & Foreign Highway

Accurate calculation of manufacturing parameters is the key to the efficient，high-precision，and rapid installation of large sections of continuous steel box beam bridges.Taking the steel box beam with the variable section in Shenzhen-Zhongshan Passage as the background，this paper first established a finite element model of the beam element in the whole construction process to obtain the pre-camper.Secondly，the average neutral axis position was calculated based on the height of the neutral axis of each beam section.Then，according to the deformation characteristic that the beam length remained unchanged at the mean neutral axis，the pre-camber was superimposed at the mean neutral axis to get the …

Key Technology For Construction Of New Single‑Wall Steel Suspended Box Cofferdam With High Pile Tied Beams In Deep Water, Yang Jinlong, Zhao Lin, Jiang Qunlong

Journal of China & Foreign Highway

In order to ensure the safe，efficient，and economical completion of the construction of the high pile tied beam of Muping Xiangjiang River Bridge in deep water，a new type of single-wall steel suspended box cofferdam was designed to act as the water retaining and enclosure structure during high pile tied beam construction according to the characteristics of deep water level and shallow stratum cover layer at the high pile tied beam location.Through the innovative design of steel casing on the bottom of the steel suspended box cofferdam，the design height of the wall panel and the amount of steel input were reduced.On the …

Influence Factors Of Carbonization Of Tunnel Segment Structure And Life Prediction Analysis, Li Dongbiao, Miao Miao, Shen Caihua, Chen Wei

Journal of China & Foreign Highway

There are many factors that affect the carbonization life of concrete segments in underwater tunnels，and the prediction methods are not uniform.In this paper，combined with actual engineering，the influencing factors and laws of carbonization of concrete segments in underwater tunnels were analyzed，and three methods for predicting the life of concrete segments were established with the crack limit as the control target.The prediction results of the three methods were compared.The results show that the influence of the temperature and CO2 concentration in the tunnel predicted by the three methods on the life of the tunnel lining structure is basically consistent with the existing …

Key Technology For Incremental Launching Construction Of Double Guide Beam Of Steel Box Girder, Sun Xiaoqiang, Yue Xinxing

Journal of China & Foreign Highway

By taking the incremental launching construction of the steel box girder at the 6th hole of the approach bridge of Baoji Taigu Bridge as the engineering background，the original plan adopted single-guide beam multi-point walking incremental launching technology for assembly and incremental launching on the prestressed reinforced concrete beam of the adjacent hole.Since the middle span of the concrete beam cannot withstand the concentrated force at the incremental launching points，the multi-guide beam multi-point walking incremental launching technology was finally used to arrange the incremental launching points at the transverse diaphragm plate of the end of the concrete beam.By increasing the incremental …

Emergency Vehicle Dispatching Model Considering Demand Urgency And Delivery Fairness, Long Kejun, Liu Jia, Gao Zhibo, Chen Suqian, Zhang Zhonggen

Journal of China & Foreign Highway

In emergency vehicle dispatching after unexpected events，it is crucial to prioritize critical nodes with high demand urgency while minimizing excessive delivery delays at other nodes to prevent secondary impacts.On this basis，this study developed an emergency vehicle dispatching model that considered demand urgency and delivery delay fairness.Firstly，the entropy weight-TOPSIS method was used to calculate the demand urgency for each node，and a delivery delay balance index was introduced to minimize disparities in delivery delays between nodes.Secondly，a multi-objective optimization model was established with total delivery time，overall cost，and delivery delay balance as objectives，while considering constraints such as inventory levels at distribution centers and route …

Working Properties Of Steel Tube Batter Piles With Concrete Infill Based On Abaqus, Yang Meiliang, Li Liemin, Sun Kunjiang, Han Rui, Zhong Yang

Journal of China & Foreign Highway

In order to explore the respons e characteristics of steel tube batter piles with concrete infill under vertical load，the steel tube batter pile with concrete infill used in Saribas Bridge in Malaysia was taken as the research object.Based on the numerical simulation method，the frictional resistance of the inner and outer walls of the steel tube，the frictional resistance around the pile at the section，and the bending moment bearing ratio between the steel tube and the concrete core of this type of batter pile under vertical load were studied.The results show that the passive-side frictional resistance of the 0–15 m pile section …

Construction Site Planning And Logistical Operations: Site-Focused Management For Builders, Second Edition, Randy R. Rapp, Bradley L. Benhart

Purdue Handbooks in Building Construction

Organizing and administering a construction site so that the right resources get to the right place in a timely fashion demands strong leadership and a well-defined, disciplined process. Good logistical operations enable profitability, and this book is the essential, muddy boots guide to such management. Written by experienced educator–practitioners, Construction Site Planning and Logistical Operations is a popular guide to the knowledge, skills, and abilities needed by project superintendents, especially, but useful to all constructors. This second edition is updated to include new technologies, resources, and details of operational planning. Leadership imperatives and management techniques remain integrated throughout. The book …

How Will Ai Impact Knowledge Sharing Within Construction Clustering? Bringing Back The Conversation On Social Contagion Within Construction Clusters, Oluwasegun O. Seriki, Mark Mulville, Ruairi Hayden

Conference Papers

Construction clusters and innovation systems play a crucial role in enhancing competitiveness and fostering sustainable development in the construction sector. These clusters facilitate knowledge sharing, interactive learning, and collaborative innovation among firms, institutions, and other stakeholders. The success of construction clusters depends on numerous factors, including firm size, economic climate, and attitudes towards innovation. While some clusters transform into innovation systems by becoming tacit-knowledge intensive, there is not much data or investigation into how they may adapt to changing demands spurred by advances in artificial intelligence (AI). There is some preliminary research highlighting the lack of dispersed innovation networks within …

Leveraging Machine Learning For Defect Detection In Irrigation Concrete Canal Lining In Egypt: Advancing Construction Quality And Efficiency, Mohamed Nabawy

Civil Engineering

Abstract:

Defects during the construction phase of projects pose significant challenges, particularly in terms of

safety, cost overruns, delays, and labor inefficiencies. In irrigation concrete canal lining construction

with mega investments, early detection of defects is critical to ensuring quality and project success.

This study explores the application of machine learning (ML) for onsite defect detection, focusing

on the development and deployment of an object detection mobile application specifically tailored

for identifying visible defects in concrete canal lining construction. Leveraging the machine learning

capabilities of Microsoft Azure, a custom object detection model was trained and validated to

recognize defects such …

Increasing Drift Capacity Of Non-Ductile Concrete Shear Walls Through Confinement With Fiber-Reinforced Polymer Application, Andrew Duong, Sophia Maglabe, Sheyna Rongong

Architectural Engineering: Graduate Reports

The seismic response and laboratory testing of pre-1980s reinforced concrete (RC) shear walls commonly exhibit undesirable concrete crushing and rebar buckling in the wall end-zones leading to a flexural compressive failure. The lack of ductility of these walls is attributed to low reinforcement ratios and absence of special boundary elements (SBE) as required by modern design code. Thus, the authors are proposing a fiber reinforced polymer (FRP) retrofit method to provide confinement to the end-zones of pre-1980s walls equivalent to that of an SBE. Current industry applications of FRP have largely been for shear strengthening of RC beams, columns, and …

Life-Cycle Cost Analysis Of Fm4 Txdot Roadway Alternatives In Cleburne, Texas, Ethan A. Bright

2024 Fall Honors Capstone Projects - Archive

The Engineering senior design group proposed a three-span concrete bridge, merged lane intersection, and a single storm conduit system. The Honors contribution to this project was analyzing the design’s alternative’s life-cycle costs to compare the most economic design. The project’s cost consists of initial construction, maintenance, and decommission. Utilizing Texas Department of Transportation (TxDOT) bid code unit prices, each design alternative is calculated by multiplying each material amount by the unit price then summed. Although the parallel conduit system has a cheaper initial cost, it requires more maintenance during its lifetime, therefore the single conduit system was recommended. Notably, cost …

Innovative Practices And Safety Culture In Modern Construction: A Case Study Of The Millstone Weber Reconstruction Project, Ariana Alexander

Honor’s College Freeman Research Journal

This thesis explores the operations of Millstone Weber, a leading construction firm formed through the merger of Millstone Bangert, Inc., and Fred Weber, Inc., with a focus on its innovative practices and safety culture. Highlighting the Runway 17L-35R reconstruction project in Denver, Colorado, the study examines the multifaceted role of a Field Engineer and Safety Intern. Responsibilities included data management, QA/QC inspections, subcontractor coordination, and the application of advanced tools like Bluebeam for project planning and execution. The internship revealed key insights into balancing safety with efficiency, managing communication gaps, and addressing task allocation disparities. Observations highlighted challenges such as …

Sustainable And User-Driven Scope Development Framework For Engineering Design Services Of Transportation Infrastructure Projects, Ahmad Zaki Ghafari

All Dissertations

Rapid economic growth has led to a significant increase in transportation demands, exerting unprecedented pressure on infrastructure systems in the United States. State transportation agencies play a vital role in maintaining and developing transportation infrastructure networks within their regions. State transportation agencies face immense pressure from federal and state governments, elected officials, and the public to deliver projects efficiently and within budget. State transportation agencies rely on professional consultants for engineering design services. Engineering design services for transportation infrastructure projects are delayed due to incomplete inaccurate scope. For state Department of Transportation (DOTs), a streamlined scope development process is essential …

Transmission Main Construction Management - An Assessment Of Project Tracking During Transition To A Cloud Based System, Martin C. Munger

LSU New Orleans Theses and Dissertations

A massive $2B settlement between the Federal Government and the City of New Orleans to remediate the damage to municipal infrastructure from Hurricane Katrina and the failed USACE levee system required the repair of roughly 400 of 1600 miles of roadways in New Orleans. The mandated repairs included many subsurface utilities below those roads. Traditional engineering construction project management practices proved inadequate to manage such a massive undertaking on the strict timelines mandated by FEMA funding. Unprecedented volumes of work for the engineering and construction industries and the government agencies tasked with performing the work from design through construction revealed …

Nlp-Based Quantitative Methods For Measuring Highway Project Similarity To Support Project Clustering And Bundling, Quan Do

All Dissertations

State highway agencies (SHAs) often need to classify similar projects into distinct work type clusters, enabling them to correlate new projects with historical data on cost, schedule, pay item production rates, and project complexity. This classification also facilitates the identification of similar projects for project bundling. However, the conventional method for classifying projects into work types is inefficient, relying heavily on subjective judgment and manual review of project scope. This inefficiency hinders SHAs’ ability to effectively apply knowledge gained from historical projects to future projects. Moreover, the subjective nature of project classification is time-consuming and can result in inconsistencies and …

Effects Of Concrete With The Implementation Of Spent Coffee Grounds, Nathan Limon

Construction Management

During this study, compression tests were performed on three different concrete mix designs to evaluate the effects of spent coffee grounds as an admixture. The initial mix design was the control mix, composed of a general concrete mix design containing aggregate, cement, and water. The second mixture utilized was high strength concrete; this included aggregate, cement, and water, fly ash. The third mixture tested consisted of aggregate, cement, water, and spent coffee grounds. The purpose of evaluating these three different mixtures is to see whether spent coffee grounds can be implemented into concrete without compromising the compressive strength. Substituting 15% …

Collision Hazard Prevention And Notification For Construction Worker Safety Using Audio Surveillance, Kehinde Elelu

All Dissertations

The construction industry faces significant safety challenges, with collision hazards ranking as the second highest cause of annual fatalities and injuries in the United States, as reported by the Occupational Safety and Health Administration (OSHA). Current collision detection methods predominantly rely on proximity technologies, which necessitate costly and complex installations on each construction equipment piece. Furthermore, auditory situational awareness declines among workers due to hearing loss and intricate construction noises, which further heightens collision risks. This research introduces an innovative, low-cost, audio-based collision prevention technology aimed at enhancing auditory situational awareness for construction workers exposed to high noise levels. The …

Comparative Analysis Of Design-Build And Design-Bid-Build Project Delivery Methods Through Cost, Schedule And Quality Performance For Warehousing And Storage Facilities, Vijaya Ravi Prasanth Reddi

All Theses

Storage facilities are essential for e-commerce operations, providing inventory, distribution, and delivery space. As per the Bureau of Labor Statistics, the number of warehousing and storage businesses in the United States increased from 15,152 in 2010 to 21,287 in 2024, showing continuous growth over the decade. Given the recent surge, there is a need to understand the performance of these facilities better. This study aims to contrast the measure of quantitative performance of design-build (DB) versus traditional design-bid-build (DBB) project delivery methods (PDM) based on cost, schedule, and quality metrics for storage facilities. This research conducted a literature review to …