Construction Engineering and Management Commons^™

The Impact Of Project Delivery Methods On Dispute Occurrence In Public Highway Projects, Samaneh Nasrollahi, Ghada M. Gad, Alan Atalah

Master of Technology Management Plan II Graduate Projects

The construction industry is a complex and competitive industry in which different participants with different expertise, talents, and levels of knowledge work together to achieve their objectives and complete a project. Sine different participants with different interest involve in a construction project, therefore, conflicts arise and become inevitable. Conflicts in projects will cause an adversarial environment which result to disputes. Hence, if conflicts are not well managed and resolved in a timely manner, they quickly turn into disputes, which prevent the successful completion of the construction project, in terms of cost and time, and increasing the potential for poor project …

Lucidpipe™ Power System, Purdue Ect Team

ECT Fact Sheets Archive

In most gravity fed water transmission pipelines, it is desired to reduce excess pressure head to prevent undue strain on a pipeline and lower the incidence of leaks. Normally this is done with pressure reducing valves that essentially burn off this excess pressure as heat. The LucidPipe™ system converts it to low cost electricity thereby removing unwanted pressure and generating energy at the same time - energy that can be put used behind the grid or put back on the grid. The LucidPipe™ system extracts a small percentage of pressure head providing nearly invisible operation allowing water operators to fulfill …

Invasive Species Impacts On Infrastructure, Invasive Species Advisory Committee

National Invasive Species Council

Executive Summary

Invasive species represent one of the most significant threats to ecosystems, human and animal health, infrastructure, the economy, and cultural resources. Because potentially invasive, non-native species typically enter the United States through ports of entry in urban environments, some of the first observable impacts may be to infrastructure, yet little is known about the economic costs associated with these impacts to the “built” environment. In addition, federal agencies currently lack the authority necessary to effectively prevent, eradicate, and control invasive species that impact the human-built environment. This lack of authority prevents rapid response to some of the most …

I-94 Advanced Bridge Replacement, Saleem Alsharari

Honors Theses

The Michigan Department of Transportation has always felt the need of improving and increasing the capacity of the most critical highway in the state of Michigan, I-94. Part of the improvement plan is to increase the capacity of a 6-mile segment along a corridor of I-94 from French Avenue to Trumbull Avenue which is in a suburban neighborhood of Detroit. There are eight bridges built in the 1950’s that need to be re-constructed for a capacity increase. Vehicular and non-motorized traffic must be accounted for in the design of these bridges. The project is intended to increase the service life …

Outsourcing Of Building Information Modeling (Bim) Among General Contractors In The United States, James W. Fountain

Honors Theses

Building Information Modeling (BIM) is a process used by AEC industry members that simulates a construction project in a multidimensional digital model and provides multitudes of project benefits from inception to occupancy. However, a variety of barriers impede a holistic BIM implementation. Because of these barriers, some general contractors are choosing to outsource the creation and/or utilization of BIM models to specialized Information Technology (IT) firms instead of performing these processes in-house. Since little literature currently exists for BIM outsourcing, this online survey-based study aimed to identify BIM outsourcing patterns among the general contractors across the US and the perceived …

Kihefo Vocational Center: Kabale, Uganda, Jason Matthew Angerer

Construction Management

Journeyman International (JI) is a non-profit organization which acts as a platform for bringing together volunteer Architects, Designers, Engineers, and Construction Managers with humanitarian projects around the world. Kigezi Healthcare Foundation (KIHEFO) a non-profit NGO located in Kabale, Uganda is a client seeking to build a vocational center to educate the workforce of Uganda. The center will include multi-purpose class rooms, a dining hall, rabbit farm, carpentry shop, and living complex. The Architect on the project was Courtney Wedel from Cal Poly. As the Construction Manager on the project my responsibilities include; Design Assist, Feasibility Analysis, Scheduling, Estimating, and Managing …

Safety Benefit Analysis Of Alternative Delineation Practices In Michigan, Brenda C. Burdick

Masters Theses

Among the many aspects of roadway design, one important system is roadway delineation. The main purposes of roadway delineation include regulating, warning, and guiding drivers in a safe manner. Delineation systems have the potential to reduce crashes. This research sought to perform safety benefit analysis of roadway delineation practices in Michigan. Through literature review, several delineation practices, selection criteria, and previously developed crash modification factors were researched. Even though several pavement marking materials have been implemented in Michigan, a safety benefit analysis of various materials had not been performed. Sites were selected, and pavement marking material inventory data were combined …

Characterization And Delineation Of Karst Geohazards Along Rm652 Using Electrical Resistivity Tomography, Culberson County, Texas, Adam F. Majzoub

Electronic Theses and Dissertations

The Delaware Basin of West Texas and southeastern New Mexico is the major western subdivision of the Permian Basin and a northern extension of the Chihuahuan Desert. The major evaporite unit within the Delaware Basin is the Castile Formation, which consists of gypsum/anhydrite and is highly susceptible to dissolution and karsting. Manifestations of karst within the Castile outcrop are abundant and include sinkholes, subsidence features and caves, both epigene and hypogene in origin.

Land reconnaissance surveys conducted during the summer of 2015 documented abundant karst landforms in close proximity to a major thoroughfare, RM 652, in Culberson County, Texas. 2D …

Bim Innovation Capability Programme: An Irish Bim Study, Barry Mcauley, Alan Hore, Roger West

Articles

In 2011 the Royal Institute of Architects Ireland (RIAI) conducted a survey which found that BIM adoption within Ireland was quite low at 16%. Over the last five years these figures have risen significantly, with the 2016 Irish Digital Transition Survey reporting that 76% of respondents possess confidence in their organisation’s BIM skills and knowledge. This represents a significant shift of BIM adoption in Ireland over the last five years.

The BIM Innovation Capability Programme (BICP) Irish BIM study, builds on the findings from the BICP Global BIM Study by providing an in depth review of BIM in Ireland with …

Carpenters Apprenticeship Internship: Student And Industry Perspectives, Chris Falco

Construction Management

The Carpenters Apprenticeship Internship program is designed to provide students the opportunity to work as a construction laborer and get hands-on work experience. The goal of this study is to address the perceived benefits of the Carpenters Apprenticeship Internship with respect to the students, the industry members, and the union. In looking at the benefits this opportunity presents, any value that is aligned among the parties involved will be highlighted to convey the mutual advantages. Lastly, the demand among students for experience such as this will be assessed to see what the perceived value of labor experience is among students …

Technology Adoption By California Central Coast Contractors, Nicholas A. English

Construction Management

Technology is trending in Construction, but it is unclear if smaller contractors have kept up with these trends like larger national companies have. This survey of San Luis Obispo County specialty and general contractors queried technology adoption, specific software use, estimator age, and opinions of various estimating attributes. It found that the majority of contractors use traditional estimating and quantity takeoff methods, the majority of contractors are 31 years old or older, and that local estimators value experience and knowledge as opposed to computer expertise. Local contractors recognize the value technology can provide, but have not adopted it in a …

Construction Of A Chicken Coop For Use By An Early Education Facility, Luke Cypress

Construction Management

There is a demand in the early education field for methods of exposing early learners to where our food comes from and how it’s produced. An excellent source of this exposure is commonly utilized in an onsite chicken-coop. These coops are in essence working farms, producing eggs and in some cases meat. While coops are not prohibitively expensive they often fall outside the scope of normal operating or educational budgets and can be difficult to fund. The purpose of this project was to identify a school that could use and benefit from a coop at no cost to the school. …

Feasibility Study Of Using Recyclable Polyethylene (Pet) Materials As Coarse Aggregate For Concrete Mixtures, Philip M. Angelo

Construction Management

The feasibility of using recyclable household plastics, specifically those made of polyethylene, commonly used in water and soda bottles, as a replacement for concrete coarse aggregate, was assessed. A method was developed for cutting polyethylene materials into fibrous strips. These strips were then used as a replacement for the rock coarse aggregate in batches of concrete. Standard 6” x 12” test cylinders were made using the concrete mixture and subject to destructive compressive testing in order to yield the compressive strength of the concrete mix 7, 14, 21, and 28 days after pouring. Three mixtures were tested, one control with …

Photovoltaic Installation In Ecuador And The Amazon, David Mulder

Construction Management

The Photovoltaic Installation in Ecuador and The Amazon is part of a collaborative effort between two major construction clubs at Cal Poly: NECA and MCAA. Four students, two from each club, traveled with two faculty to install photovoltaics for two different communities. The first project was a solar installation to provide fresh water for the community of Santa Rosa. Project number two, was a sixteen-panel installation in Shell, Ecuador for the non-profit Reach Beyond. The main goals of each project were to provide fresh water, and achieve net zero electrical consumption.

A Case Study On Achieving 100% Customer Satisfactory Homes In Production Home Building, Garrett Whitlock

Construction Management

No abstract provided.

Bs News November/December

Building Services Engineering

No abstract provided.

Analysis Of Transit Accessibility For People With Disabilities, Rostam Khalid Mohammed Ameen Qatra

Masters Theses

The inconvenience of public transit systems and unavailability of bus stops in the United States has resulted in a heavy reliance on the private automobile. One of the main issues in transit services is accessibility, particularly for people with disabilities. This research is intended to compare estimated job accessibility measures by transit in Kalamazoo county for workers with reduced physical mobility and without. Using OpenTripPlanner (OTP) software, General Transit Feed Specification (GTFS), Open Street Map (OSM) and Longitudinal Employer-Housing Dynamics (LODES) data were analyzed to estimate job accessibility for people with mobility constraints. By using the shortest tree path method, …

Occupancy Estimation In Smart Building Using Hybrid Co2/Light Wireless Sensor Network, Chen Mao, Qian Huang

ASA Multidisciplinary Research Symposium

Smart building, which delivers useful services to residents at lowest cost and maximum comfort, has gained increasing attention in recent years. A variety of emerging information technologies have been adopted in modern buildings, such as wireless sensor networks, internet of things, big data analytics, deep machine learning, etc. Most people agree that a smart building should be energy efficient, and consequently, much more affordable to building owners. Building operation accounts for major portion of energy consumption in the United States. HVAC (heating, ventilating, and air conditioning) equipment is a particularly expensive and energy consuming of building operation. As a result, …

Comparison Of Lean Construction In India And United States Of America, Vedangi Mahashabde

Masters Theses & Specialist Projects

The concept of Lean Construction has been introduced successfully into the Construction Industry to increase efficiency and profit by elimination of non-value adding activities or ‘Waste’. Lean Construction is an adaptation of Lean manufacturing principles and is the future of the Construction Industry in developing as well as developed countries. There has been much study and documentation conducted on ‘Lean Construction’ in USA. Even though people have started practicing Lean in India, there is lack of documented information available about it. Professionals within the Industry could already be minimizing ‘Waste’ and/or following Lean principles without the knowledge of the term …

Using Building Information Modeling (Bim) And The Last Planner System (Lps) To Reduce Construction Process Delay, Zaid K. Ai Hussein

Masters Theses & Specialist Projects

The construction industry suffers from many practical problems and challenges; most being related to construction management. One of the most common recurring problems in construction projects is delay. Delay is a primary factor that can have an effect on project duration, scheduled delivery date, as well as the overhead cost of the project. This study investigated the problem of delays in construction projects. The research focused on the combination of Building Information Modeling (BIM) and Last Planner System (LPS) together to measure the execution time of construction projects. The aim of this study was to determine whether using BIM and …

High-Level Multi-Objective Model For Microgrid Design, Siamak Talebi

Theses and Dissertations

Recently, there is vast inclination toward using renewable energy in rural areas away from the main electricity generation plants. Small airports located in rural areas are good candidates to apply sustainable energy for electrical power needs. Because of the intermittency of the renewable sources, it is important to have energy storage to guarantee an uninterrupted and stable power supply for end users. In this work, a high-level micro grid model is proposed considering making decisions about different factors such as different renewable sources capacity, storage and system capacity. A multi-objective model of a microgrid high-level design is used to formulate …

Capacity Building For Sustainable Workforce In The Construction Industry, Edelmiro F. Escamilla, Mohammadreza Ostadalimakhmalbaf

The Professional Constructor

Research has shown that the construction industry will face workforce shortages that will increase delivery cost and completion time. The purpose of this paper is to first identify and synthesize the fundamental factors impacting recruitment and retention of the potential construction workforce. A qualitative approach was employed in order to collect and synthesize known factors related to workforce development and capacity building for the construction industry. The paper then presents a conceptual framework for conducting research on capacity generation of a sustainable construction workforce—by considering the impact of family unit and cultural values, career path perceptions, higher educational attainment, and …

Comparing Owner Perceptions Vs. Performance Reality On Construction Management At Risk Public School Projects, Noel Carpenter, Dennis C. Bausman

The Professional Constructor

Over the past decade construction expenditures for education have reached approximately $350 billion with $195 billion of that total spent on K-12 public schools. Public funding through state and local taxes is the primary source of support for construction and school districts are charged with spending these dollars wisely. Within the confines of procurement statutes school districts must select a delivery method that best suits their needs. Two commonly used delivery methods are Design-Bid-Build and Construction Manager at Risk (CM at Risk). This paper examines qualitative and quantitative data collected from one hundred thirty-seven new K-12 school projects constructed in …

Free Fall Of Self-Consolidating Concrete In Walls Three Meters High, Donald J. Phillippi, Katie Loughmiller, Ray Buyle, Michael Cesena

The Professional Constructor

Self-consolidating concrete, (SCC) is a highly flowable, non-segregating concrete that allows for concrete placement without vibration or external consolidation. SCC also allows rapid concrete placement with reduced labor costs, resulting in vastly improved concrete surface finishes and architectural applications (RMCAO 2009). To accomplish SCC, the concrete industry has developed improvements in high-range water reducer admixtures for flowability and viscosity-modifying admixtures for stability. The current project investigated six specimens, which provided an evaluation of SCC allowed to free fall 3 m (10 ft) that filled wall formwork with different inclinations and amounts of steel reinforcement. The purpose of the investigation was …

Bicp Global Bim Study, Barry Mcauley, Alan Hore, Roger West

Articles

The BICP is a direct response to the 2014 Construction 2020 report calling on Enterprise Ireland to work with industry organisations to promote the use of BIM and develop the appropriate technical skills amongst Irish construction firms so that they can successfully compete in markets where BIM is widely adopted or a requirement. There are four distinct work packages to achieve the strategic objectives of the BICP which include amongst other things a systematic review of BIM adoption in international regions, with particular focus on the enablers to support national implementation programmes. This study focused on exploring the value proposition …

Fall 2016 - Volume 41, Number 1, Full Issue

The Professional Constructor

No abstract provided.

Portable Modular Conveyor, Purdue Ect Team

ECT Fact Sheets Archive

The Portable Modular Conveyor-Material Placer (PMC) is a quick, easy, dependable and cost effective way to place materials in the limits of the confined grade or work area. This specialized piece of equipment was developed to place concrete in front of a concrete slip form-paving machine. The typical method of placing concrete requires a self-propelled belt placer, which is very expensive to purchase and mobilize to the jobsite. The PMC creates a significant cost savings in labor and equipment with the PMC. It is a direct replacement for conventional material placing equipment, including all in grade belt placing machines. As …

Bs News September/October

Building Services Engineering

No abstract provided.

Strength Of Reinforced Concrete Beams With High-Strength Steel, Brian C. Rogers, Aishwarya Puranam, Santiago Pujol

The Summer Undergraduate Research Fellowship (SURF) Symposium

Structures are commonly made of reinforced concrete, which is a composite material made of concrete and steel reinforcement. Using high-strength steel, with yield stress larger than 100 ksi, could help reduce the quantity of steel required in structural members, thus reducing costs and improving constructability. The hypothesis being tested is that smaller quantities of high-strength steel reinforcement (HSSR) can be used in place of conventional steel in reinforced concrete beams while maintaining similar strength and deformation at failure. Two reinforced concrete beams with two different types of longitudinal steel reinforcement were constructed. The beams were 18 in. wide, 30 in. …

Modeling Atypical Building Use With Commercially Available Building Simulation Software, Sarah E. Schanck

Theses and Dissertations

National Guard armories are audited to provide recommendations for future energy reduction measures. The annual energy consumption of a New Jersey National Guard Armories cannot be modeled directly with commercially available building simulation software, due to discrepancies between the modeling capabilities of the software and the reality of the armory. A building simulation software, eQUEST, was chosen for use in this project. Discrepancies between eQUEST inputs and reality were identified and correction factors developed to minimize the effect of each discrepancy on predicted energy consumption, with the end goal of accuracy between predicted and actual energy consumption. In addition, an …