Construction Engineering and Management Commons^™

The Development Of A Convenient And Consistent Methodology For Flight Proficiency To Certify Multi-Rotor Uas Pilots For State Departments Of Transportation, Colin H. Dees, Joseph M. Burgett

The Professional Constructor

To fly an unmanned aircraft system (UAS), commonly referred to as a “drone,” the Federal Aviation Administration (FAA) requires pilots to pass a knowledge test. There is no requirement at the state or federal level for drone operators to demonstrate the ability to operate a UAS. The National Institute of Science and Technology (NIST) has created an exam for public and private entities to assess basic UAS flight proficiency. It is the only nationally recognized flight proficiency protocol. NIST does not provide a scoring recommendation and leaves it to the user to determine the minimum criteria to pass. There is …

A Productivity Rate-Based Comparative Carbon Footprint Cost Analysis Of Small To Large-Sized Open-Cut Pipeline Installation Activities For Sanitary Sewerage Construction: A System Boundary Concept, Amir Reza Zakeri

Civil Engineering Theses

Underground sanitary sewer pipelines are essential components of urban infrastructure; however, open-cut pipeline installation requires excavation, bedding preparation, pipe placement, backfilling, embedment, and compaction activities that rely heavily on construction equipment and fuel consumption. As a result, open-cut installation can generate measurable greenhouse gas emissions during the construction phase. With increasing attention to sustainable infrastructure delivery, there is a need for a consistent approach to quantify construction-phase carbon footprint and convert those emissions into a comparable economic indicator. Accordingly, this thesis aims to create and apply a productivity rate-based calculation framework for estimating and comparing construction-phase CO₂e emissions and carbon …

Smart Dynamic Concrete: Effect Of Coarse Aggregate Size Distribution On Fresh, Mechanical And Durability Properties, Venu Sipelli, Kamineni Aditya, Shravya Sripadapu

Mansoura Engineering Journal

SDC is a self-flowing concrete that demonstrates improved material efficiency through optimized aggregate gradation. Unlike SCC, which relies on high powder content for improved flowability, SDC provides improved flowability by optimized aggregate gradation, making it a promising alternative to SCC. This paper presents the fresh, mechanical, and durability performance of M40-grade SDC using OPC 53 grade cement, GGBS, CRF, and polycarboxylate-based superplasticizer. A constant cementitious content of 470 kg/m³ and water–cement ratio of 0.38 were maintained. The fresh, mechanical, and durability performances of SDC using three types of coarse aggregate combinations, namely, 70% 10 mm + 30% 20 mm, 75% …

Impact Of Natural Disasters On Construction And Engineering Solutions, Karima Ao Damson

Williams Honors College, Honors Research Projects

This Honors Research Project seeks to research and explain the impact of natural disasters on the construction and reconstruction of infrastructure in countries with the highest risk of natural disasters and compare them to the requirements in the United States in the states most prone to natural disasters. The objectives are to identify the countries most prone to natural disasters, describe the environmental impacts of the natural disasters, describe the impacts on construction and reconstruction requirements, and research whether construction and civil engineering solutions currently applied to the individual countries could be improved or reproduced in other countries exposed to …

The Professional Constructor, Full Issue

The Professional Constructor

Full Issue, Winter 2026

Volume 50, Number 01

Managing Green And Sustainable Construction Projects: A Computational Analysis Of Associated Risks And Challenges For Improved Performance, Bahaa Chammout, Islam H. El-Adaway

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Green and sustainable building practices have emerged as effective strategies to address the environmental challenges posed by the construction industry. This includes unsustainable resource utilization, excessive waste production, greenhouse gas emissions, and high energy consumption. However, the integration of green and sustainable initiatives in construction introduces distinct risks and challenges that affect project management and may lead to claims and disputes. To this end, and while previous research examined dispute causation across various aspects of the construction industry, there is limited investigation of the unique and complex nature of risks and challenges - and consequently conflicts, claims, and disputes - …

Managing And Accelerating The Circular Economy Transitions Within The Construction Value Chain Using Network Governance And Game Theory Systems Perspectives, Radwa Eissa, Islam H. El-Adaway

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The fragmented nature of the construction industry has hindered its transition toward circular economy (CE) practices. While game theory (GT) has been successfully applied to support the strategic decisions of CE transitions in other sectors, CE-GT models in the construction domain remain extremely limited. This paper addresses two research questions: (1) how are CE network governance activities currently modeled using GT across domains? (2) How can such models be transferred and adapted to solve strategic interactions within the construction value chain in a manner that enables CE practices to emerge as equilibrium outcomes? These questions are driven by the need …

Analytical And Empirical Data-Driven Risk-Governance Design Across The Different Phases: Creating Informed Policy Adjustments For The Transportation Project Lifecycle, Mariam A. Elazhary

Doctoral Dissertations

"Transportation infrastructure is a critical foundation for economic productivity, yet agencies still face challenges in translating the expanding transportation datasets into defensible, phase-specific risk-governance tools. This dissertation addresses this gap by developing analytical and empirical, data-driven approaches to support risk governance across the transportation project lifecycle. Module 1 uses a panel model with bid-letting data to examine how out-of-state contractor participation affects pre-award competition and to derive entry-governance rules. Module 2 analyzes nonfatal injury data through iterative multiple linear regression and fatality data through association-rule change mining to identify multi-factor safety-risk configurations and develop adaptive safety-governance provisions. Module 3 develops …

Advancing Management Strategies For Airport Infrastructure Development: A Holistic Project Delivery And Contractual Perspective, Ramy Ahmed Anwar Ahmed Khalef

Doctoral Dissertations

The airport sector plays a vital role in the US infrastructure. Neglecting the maintenance and improvement of such critical domain poses serious repercussions. Current initiatives within the aviation sector have fallen short in providing substantial quantitative or qualitative support for comprehensive project and risk management processes. This research fills this knowledge gap. The associated objectives include: (1) identifying a holistic set of Design-Build risk factors and providing associated research recommendations; (2) enhancing the understanding of Design-Build (DB) with respect to Design-Bid-Build (DBB) on key risks impacting schedule/cost performance in airport projects; (3) establishing a risk-based benchmarking framework to evaluate schedule/cost …

Bond Behavior Of Uhpc-Nsc Interfaces For Bridge Deck Repair Under Flexural Loading, Larissa Santiago La Banca

Graduate Studies Theses and Dissertations 2026

The use of ultra-high performance concrete (UHPC) has increased due to its superior mechanical properties and strong bond with normal-strength concrete (NSC). It is widely used as a repair material, particularly in bridge decks, where maintenance remains a challenge. However, the interface between UHPC and NSC is often the weakest region of the composite system and requires careful evaluation.

This study investigates the bond behavior between UHPC and NSC using different surface preparations, test setups, and UHPC materials. The experimental program included unreinforced beams with vertical interfaces tested under three- and four-point flexural loading, and reinforced slabs with horizontal interfaces …

Assessing The Criticality Of Construction Trades: Skilled Labor Shortages And Their Cost And Schedule Impacts, Tamima Elbashbishy, Islam H. El-Adaway

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Skilled labor shortages are a pressing issue in the construction industry. Existing research has primarily focused on the effects of labor shortages at the project or industry level, but there is limited exploration of how these shortages vary across specific trades and their distinct impacts on project outcomes. Evidence indicates that labor shortages vary significantly among trades. This paper addresses this knowledge gap through quantitatively assessing the criticality of key construction trades based on the (1) extent of skilled labor shortages currently witnessed in each trade, (2) impact of these shortages on cost and schedule performance, and (3) degree of …

Moving From Feasible Solutions To Sustainable Systems In The Built Environment, Mohammed Ali Berawi, Mustika Sari, Perdana Miraj

CSID Journal of Infrastructure Development

The built environment plays a crucial role in global sustainability efforts. Buildings, infrastructure, and cities consume large amounts of energy and materials that shape social behavior, and lock in environmental impacts. Over the past two decades, research has produced a wide range of technical solutions to reduce these impacts. Renewable energy systems, energy-efficient buildings, alternative construction materials, and new construction methods are no longer experimental concepts. Many have proven technical and economic potential. Yet, real-world transformation remains slow and uneven. This gap suggests that sustainability challenges in the built environment are no longer driven by a lack of technology. Instead, …

Barriers To The Adoption Of Modular Construction Technology In South Africa, Mokete Matoba, Christopher Amoah

CSID Journal of Infrastructure Development

Construction, mining, and manufacturing are the most significant contributors to South Africa's GDP. While manufacturing and other industries utilise advanced technologies to enhance productivity, he construction industry continues to lag behind in technological adoption. This study examines the barriers that hinder the South African construction industry from leveraging the benefits of modular construction technologies (MCT). The study employed a quantitative research method, using closed-ended questions to collect data. The questionnaires were emailed to South African construction industry professionals selected through a combination of purposive and convenience sampling. A total of 98 questionnaires were distributed, of which 46 were returned. However, …

Effects Of Calcination Conditions Of Locust Bean Pod On The Mechanical Properties Of Locust Bean Pod Ash High-Strength Concrete, Iorwuese Anum, Umar Abdullahi, Megat Azmi Megat Johari, Felix Nkapheeyan Isa

CSID Journal of Infrastructure Development

Locust Bean Pod Ash (LBPA) is produced from the calcination of Locust Bean Pod (LBP), an agricultural waste of the African locust bean tree (Parkia biglobosa). This study evaluated the use of LBPA obtained through controlled calcination and open burning as a supplementary cementitious material (SCM) in high-strength concrete (HSC). Cement was replaced by LBPA at 5%, 10%, 15%, and 20% by weight using both ashes—LC for ash produced through calcination at 600 °C, and LO for ash obtained through open burning. Slump and strength were assessed, including compressive strength (100 × 100 × 100 mm cubes) and splitting tensile …

Enhancing Health And Safety Practices In Construction Site In Developing Nations Through Technology Advancement In South Western Nigeria, Mubaraq Lawal, Abba Mahmud, Ismail Gbolahan Dere, Thankgod Agbo Owoicho

CSID Journal of Infrastructure Development

The construction sector plays a critical role in urban development and economic growth, yet it continues to face major challenges that threaten worker health and safety. Traditional safety measures are not always sufficient for the complex conditions found on construction sites, which creates a need for technology‑based solutions. This study investigates the relationship between technology adoption and health and safety practices in the construction industry in Lagos, Nigeria. The study identifies the major causes of site accidents, examines the level of technology use on construction sites, and reviews existing literature through both primary and secondary data. Primary data were collected …

Exploring The Horizontal Static And Dynamic Shading Devices To Minimize Cooling Load In Tropical Buildings, Hilmi Fitriatulamal, Ova Candra Dewi, Miktha Farid Alkadri, Kartika Rahmasari

CSID Journal of Infrastructure Development

Shading devices are essential for reducing solar radiation and cooling loads in buildings located in tropical climates. In the Jakarta region, the highest solar factor is observed on west- and east-facing facades, followed by north- and south-facing orientations. National building policy in Indonesia encourages facades to face north–south to reduce solar heat gain. This study explores horizontal static and dynamic shading devices on north-facing facades and evaluates their impact on cooling load reduction and daylight performance. The methodology includes calculating and simulating energy use intensity (EUI) using EnergyPlus and conducting illuminance analysis using Radiance and Grasshopper. Key parameters considered in …

Smart Building Rating System: A Comparative Analysis Of National And International Rating Systems, Amanah Hamidah, Mohammed Ali Berawi, Mustika Sari, Gunawan Saroji

CSID Journal of Infrastructure Development

Smart buildings have become a key part of the Fourth Industrial Revolution, driven by the need for efficient, sustainable, and adaptive built environments. Their importance is growing alongside Indonesia’s effort to develop smart cities. This study compares Indonesia’s national smart building certification system, established under Ministerial Regulation No. 10 of 2023, with two international systems: the European Union’s Smart Readiness Indicator (SRI) and the SmartScore certification. The analysis uses a literature review and comparative method to examine each system’s assessment criteria, scoring method, and certification tier. The findings show that Indonesia’s regulation includes six parameters, such as cybersecurity and operational …

The Use Of Local Materials For The Interior Quality Of Swahili Building Design In Tanzania, Luiana Makundi, Jacob Lutta

Tanzania Journal of Engineering and Technology (TJET)

Swahili architecture in Tanzania is recognized by spatial capacity to adapt environmental changes. This research explores the role of locally available materials in shaping the interior quality by focusing on functional, aesthetic appeal and supporting sustainable environment. A mixed-methods approach was applied which, involves field surveys, case study and interviews with different local professionals in building industry. Dar-es-Salaam was used as a case study area that was critically analysed to identify construction practices and applications of local materials in building interior spaces. A particular focus was placed on materials durability, aesthetic, ecological, environmental balance and thermal efficiency which seems to …

Shaking Table Test And Numerical Simulation Of Seismic Response Characteristics Of Rock Slope With Muddy Interlayer, Duan Chenggang, Fang Yanlin, Tian Yeqing, Zhou Zhijun

Journal of China & Foreign Highway

In order to study the seismic macroscopic failure process and dynamic response characteristics of rock slope with muddy interlayer and reveal the influence of muddy interlayer on slope stability,a similar slope model with concave and convex slope types was designed,and shaking table test was carried out;finite element analysis was used for numerical modeling analysis,and the results obtained by the two models were compared.The results show that:① The macroscopic deformation and failure process of the model slope is divided into three stages.Muddy interlayer dislocates,and cracks occur;mud interlayer slips,and cracks expand;slope collapses;② The seismic load has a decisive influence on the stability …

Effect Of Lithium Slag Dosage On Strength And Dry Shrinkage Properties Of Cement Stabilized Recycled Macadam, Zhao Ziyu, Gan Xianyong

Journal of China & Foreign Highway

To improve the mechanical properties and dry shrinkage properties of cement stabilized bases formed by cold in-place recycling of cement concrete pavements,lithium slag was mixed into the recycled mixture in mass ratios of 0%,6%,9%,and 12%.The effects of lithium slag dosage on the mechanical,dry shrinkage,and water stability properties of the recycled base were analyzed through the unconfined compressive strength,splitting,dry shrinkage,and water stability tests,and the mechanism underlying the improving effect of lithium slag on the cement stabilized base formed by cold in-place recycling of the cement concrete pavement was analyzed by X-ray diffraction (XRD ) and scanning electron microscopy (SEM ).The results …

Optimization Of Infill Concrete Dimension In Composite Girder Box Based On Igrnn, Wang Yafeng, Liu Jian, Ke Hongjun

Journal of China & Foreign Highway

The mechanical performance of the negative bending moment zone of steel-concrete composite continuous girders has always been a focus of attention in bridge engineering.Existing research mainly proposes improvement measures for the tension of concrete bridge decks,while paying little attention to the common phenomenon of steel girders bearing pressure.The steel girders in steel-concrete composite girders,especially the steel bottom plate in the negative bending moment area of the pier top,bear the highest compressive stress of the entire bridge.Therefore,by taking a steel-concrete composite girder bridge in Zhejiang Province as the engineering background,it is proposed to partially fill the interior of the box girder …

Research On Cable Force Optimization Of Long-Span Cable-Stayed Bridges Based On Rbfnn+Improved Parti Cle Swarm Optimization Algorithm, Deng Da, He Bowen, Liu Guokun

Journal of China & Foreign Highway

In view of the cable force optimization problem of long-span cable-stayed bridges,a cable force optimization method considering the reliability index of stay cables was proposed based on the response surface fitted by the radial basis function neural network (RBFNN ).The RBFNN-based response surface model for solving the reliability index was established by fitting the structural implicit function through RBFNN training.The improved particle swarm optimization algorithm was used to search for the optimal solution of the cable force optimization model considering the reliability index.The research results show that RBFNN can accurately predict the structural responses and fit the structural implicit performance …

Design Optimization And Experimental Study Of Cfrp Plate Anchorage With Clip-Extension Type, Qi Yijia, Xiao Dan, Wang Zhongqiang

Journal of China & Foreign Highway

Existing anchorage is prone to damaging the carbon-fiber reinforced polymer (CFRP ) plate due to the “notch effect ” and uneven distribution of clamping stress.This study proposed a new clip-extension type anchorage for the CFRP plate.This design utilized the ductility of steel for stress diffusion and guided the compressive stress zone in the CFRP plate away from the notched end,realizing a smooth transition of the clamping force of the CFRP plate at the clip port and effectively reducing the “notch effect ”.The design also reduced the strain difference between the carbon fibers,resulting in a more synchronized lateral deformation of the …

Research And Applicat Ion Of Ultra Large-Scale Consolidated Under-Reamed Drilled Shaft Technology Under Special Environmental And Geological Conditions, Ding Yi, Yu Kun, Shi Haiyang, Pei Xiaofeng, Zhu Bo

Journal of China & Foreign Highway

This article aims to add ress the poor economic efficiency of large-diameter and ultra-long piles,the high risk of hole collapse in thick sandy soil,and the limited space across the canal faced by the Bridge over Yellow River Diversion to Qindao Canal on Zhanhua ‒ Linyi Expressway.According to the comparison of conventional drilled cast-in-place piles with combined pile-end and pile-side post-grouting,the industry ’s under-reamed drilled shaft foundation with the largest disc diameter (4.5 m) and the largest single-pile volume (456 m3) was proposed and designed.At the same time,supporting devices such as three-arm rotary cutting drill bits and long arm borehole diameter …

Analysis Of Influence Of Internal Erosion On Deformation Of Subway Station Structure, Qin Tianxin, Wang Chen, Tan Xuyan, Wei Shengming, Liang Fayun

Journal of China & Foreign Highway

Under the long-term effects of disasters such as rainstorms and floods,the soil layer around subway stations may be affected by internal erosion,threatening the structural safety of urban subway stations.To explore the influence of internal erosion on subway station structures,this study conducted isotropic consolidation and triaxial compression tests on gap-graded sand soil.Eroded soil specimens were simulated by adjusting the fine particle content to explore the pattern of variations in physical and mechanical properties caused by internal erosion.Results indicate that internal erosion alters the stress-strain relationship of gap-graded sand soil,increasing compressibility,decreasing shear strength,and weakening dilatancy.Drucker-Prager (DP) cap model parameters for eroded sand …

Evaluation Method For Nighttime Visual Space Improvement On Mountain Roads, Zhao Yan, Chen Yanli, Chen Jiale

Journal of China & Foreign Highway

To address issues such as poor visual guidance,narrow field of view,and short sight distance during nighttime driving on mountain roads,this study proposed a visual space enhancement evaluation method applicable to mountainous roads at night.By integrating active and passive traffic safety facilities,a visual space enhancement strategy adapted to the nighttime environment of mountain roads was proposed.A multidimensional evaluation indicator for visual space was established based on co-simulation.The effectiveness of the strategy was verified from the perspectives of visual space expansion and driving safety improvement by taking a trunk highway in the Qinling mountainous region as a case study.The results show that …

Utilization Technology And Compaction Quality Control Of Hardened Layer In Beam Yard Of Rock-Filled Roadbed, Cheng Xiaoliang, Tian Wendi, Gao Mengke, Zhou Xujia

Journal of China & Foreign Highway

To investigate the utilization technology and compaction quality control of hardened layers in the beam yard of rock-filled roadbed,the optimization design and construction control methods for rock-filled roadbed under different conditions were proposed based on a highway project in Guangdong Province.When the elevation of the hardened layer was lower than the top surface elevation of the roadbed and the top surface bending and settlement value of the hardened layer was less than that of the rock-filled roadbed,the gravel material could be filled directly on the hardened layer to the top surface elevation of the roadbed,and acceptance and pavement design could …

Reflection Cracking Resistance And Fatigue Performance Of Super-Flexible Fma Mixture, Lan Yong, Deng Xinghe, Zhang Zida, Wu Kuanghuai, Ding Weizhe, Guan Xuebing, Peng Tiekun

Journal of China & Foreign Highway

To investigate the fatigue performance and reflection cracking resistance of super-flexible fluid mastic asphalt (FMA ) mixtures,this study designed a super-flexible FMA- 13 mixture by the mastic flow for filling (MaFF ) method.The effects of temperature and maximum horizontal tensile displacement on the cracking resistance of both FMA- 13 and GAC- 13 (as the control ) mixtures were explored via the Overlay Tester.Additionally,small-scale accelerated pavement loading tests were conducted to analyze the effect of load cycles on the rebound modulus of the FMA- 13 mixture.A nonlinear fatigue damage model was employed to predict the fatigue life of both mixtures.The results …

Research On Pavement Roughness Evaluation Method Based On Smartphones, Siriguleng Bai, Yili Guoqi, A Rong, Guo Guoying, Wang Jing

Journal of China & Foreign Highway

To address the low efficiency and high cost of current detection methods,as well as the insufficient accumulation of pavement damage data on rural low-grade roads,this study developed a vehicle vibration data acquisition application based on smartphones and proposed a conversion method for calculating an index equivalent to the international roughness index (IIRI).Vertical acceleration signals collected during vehicle travel were proposed through high-pass filtering and denoising to calculate the vertical displacement,from which a converted I'IRI was derived.Experimental results show that although the data collected by smartphones has slightly lower accuracy than that collected by professional detection equipment,the proposed I'IRI exhibits a …

Sound Attenuation Characteristics In Relation To Compaction Degree In Sandy Soil, Liu Junbin, Long Shiguo

Journal of China & Foreign Highway

In order to investigate the effect of water content and compaction degree on the attenuation characteristics of sound waves in sandy soil,this paper first determined the particle gradation of the soil through a sieving test and identified its optimal water content through a compaction test.Then,six sets of ring knife specimens of sandy soil with different water contents and nine sets with varying compaction degrees were prepared.Ultrasonic testing was carried out using the acoustic transmission method,and the received acoustic signals were subjected to time-frequency analysis to extract acoustic characteristic parameters indicative of the compaction degree.Finite element simulation was employed to explore …