Chemical Engineering Commons^™

A Promising Modification Of Pt Surfaces With Cnts For Decreasing Poisoning Impact In Direct Methanol Fuel Cells, Islam M. Al-Akraa Dr., Yaser M. Asal Mr, Aya A. Khalifa Ms.

Chemical Engineering

Direct methanol fuel cells (DMFCs) are clean energy sources that have many applications due to the high energy density of methanol as a fuel. However, this type of fuel cells (FCs) has limitations that are preventing it from being commercialized. One such limitation is the adsorption of intermediates such as CO into the surface of the Platinum (Pt) catalyst during methanol oxidation (MO) which deactivates its active sites, where the reaction is taking place, and leads to poisoning of the electrode over the long term. In this study, multi-walled carbon nanotubes (MWCNTs) have been introduced to the Pt-modified glassy carbon …

Novel Adsorbent For Industrial Wastewater Treatment Applications, Islam M. Al-Akraa, Ahmed Y. Zakaria Eng, Dalia A. Ali Eng, Hany A. Elazab Dr, Hoda A. Elsawy Dr

Chemical Engineering

In this study, the hydroxyapatite powder is investigated for both of methylene blue and thymol blue in aqueous solution. The physical and chemical properties of the adsorbent were evaluated systematically using the different techniques including Microsoft Excel programming, linear regression model and also the coefficient of determination. Batch adsorption experiments were conducted to determine the effect of contact time, solution pH, initial dye concentrations, and also the adsorbent dosage on adsorption. The adsorption kinetic parameters confirmed the better fitting of pseudo-second order kinetic model for both of methylene blue and thymol blue. The isotherm data of methylene blue and thymol …

Enhanced Electro-Oxidation Of Methanol At Pt-Au Nanocatalyst For Direct Methanol Fuel Cells, Islam M. Al-Akraa Dr., Yaser M. Asal Mr, Ahmad M. Mohammad Prof

Chemical Engineering

In this investigation, a Pt-Au nanocatalyst prepared by the coelectrodeposition of Pt (PtNPs) and Au (AuNPs) nanoparticles is assembled onto a glassy carbon (GC) electrode for efficient methanol oxidation (MO). Several molar ratios between PtNPs and AuNPs have been used and the corresponding catalytic activity towards MO is tracked. The Pt1:Au1 catalyst showed the highest catalytic activity (5 times higher oxidation peak current (Ip) and a 126 mV negative shift in the onset potential (Eonset) toward MO). The catalyst’s morphology, composition and activity are investigated and the ehancement mechanism is recognized.

A Simple And Effective Way To Overcome Carbon Monoxide Poisoning Of Platinum Surfaces In Direct Formic Acid Fuel Cells, Islam M. Al-Akraa Dr., Yaser M. Asal Mr, Sohair A. Darwish Ms

Chemical Engineering

A glassy carbon (GC) electrode modified with multi-walled carbon nanotubes (MWCNTs) and platinum nanoparticles (PtNPs), Pt/MWCNTs-GC, has been introduced for formic acid electro-oxidation (FAO). A similar loading of PtNPs has been conserved for a proper comparison between the Pt/MWCNTs-GC and the unmodified Pt/GC electrodes. The modification with MWCNTs could enhance the loading of PtNPs onto the GC electrode in a way that minimizes its agglomeration and increases its dispersion in the CNTs network. This not only increases the surface area exposed to the reaction but also interrupts the contiguity of the Pt active sites minimizing the adsorption of the poisoning …

Empirical Modeling Of Urea Synthesis Chemical Equilibria, Moustafa A. Soliman

Chemical Engineering

In this paper empirical formulas for the chemical equilibrium of reactions involved in urea synthesis are derived. Their accuracy is checked against data obtained from the application of Aspen Plus to a urea plant based on Stamicarbon technology. The accurate results obtained support their application in the simulation of the reactions involved in urea synthesis.

Approximate Analytical Solution For Mathematical Models Of Thermal Ignition And Non-Isothermal Catalytic Zero Order Reaction In A Spherical Geometry, Moustafa A. Soliman

Chemical Engineering

In this paper an approximate analytical solution for the Frank-Kamenetskii equation modeling thermal ignition without the depletion of the combustibles in a spherical annulus and non-isothermal zero order reaction in spherical catalyst particle is presented. The approximate solution is compared with the numerical solution and is in good agreement with the numerical solution. The approximate solution obtained is valid for all values of the distance parameter. Multiple solutions occur for some range of Frank-Kamenetskii parameter (λ). The multiplicity is infinite for the case of a solid sphere and λ=2.Interesting relation is obtained for λ at the turning points. For the …

Development Of A Dynamic Model And Control System For Load-Following Operation Of Supercritical Pulverized Coal Power Plants, Parikshit S. Sarda

Graduate Theses, Dissertations, and Problem Reports (ETD)

Thermal power plants that have been designed to operate at their rated capacity are being forced to cycle their load and operate under low-load condition to meet changing load demands due to the increased penetration of renewables into the electric grid. The rapid load-following operation is leading to challenging control problems. The goal of this research is to develop dynamic model and control system for efficient load-following operation. The focus of this work is on supercritical pulverized coal (SCPC) power plants. The steady-state model is developed using Aspen Plus and Aspen Custom Modeler and then converted to a pressure-driven Aspen …

Mechanism Study Of Shale Gas Conversion Via Chemical Looping And Heterocatalytic Processes, Lei Bai

Graduate Theses, Dissertations, and Problem Reports (ETD)

The shale gas revolution has significantly changed the energy landscape in US. The technical-feasible, energy-effective schemes for shale gas combustion and utilization, especially from remote resources, have attracted increasing interest due to expensive transportation/distribution cost. In this research, for the first time, chemical looping combustion (CLC) of methane with inherent CO₂ capture, oxidative coupling of methane (OCM) and dehydro-aromatization (DHA) of ethane are systematically studied as promising alternatives at O₂-rich, O₂-lean and non-oxidative conditions, respectively.

Chemical looping combustion is bridging clean fuel combustion in energy production with inherent CO₂ capture. CLC utilized an oxygen …

New Method Of Manufacturing Carbon Foam, Matthew D. Artimez

Graduate Theses, Dissertations, and Problem Reports (ETD)

Carbon foam is a product that has some unique features. Carbon foam is a light weight material that has a high crush strength. It is electrically conductive, but because it is composed of air space between the tendrils, it is not a thermal conductor. Since it contains no volatile content, it is noncombustible. All these features allow carbon foam to have many modern applications. Currently, there are only three methods of producing carbon foam, and all three are not cost- efficient enough to meet the demand of potential new markets.

In this thesis, a new procedure of producing carbon foam …

Development Of A Sustainability Evaluation And Control Framework For Chemical Processes, Shuyun Li

Graduate Theses, Dissertations, and Problem Reports (ETD)

Industry, government, and society have begun to shift from economic stand-alone focus to the inclusion of sustainability in the decision-making process. This shift can be attributed to the growing environmental and social awareness that makes consumers and stakeholders not only care about product quality and cost, but also products and processes that minimize the environmental impact and conserve natural resources. As a result, some progress has been made in recognizing and understanding the challenges of sustainable development, which helps evaluating the sustainability performance of a specific process/product. In particular, sustainability assessment tools and methodologies have been developed to help the …

Design Of Geothermal District Heating And Cooling System For The West Virginia University, Oluwasogo Bolaji Alonge

Graduate Theses, Dissertations, and Problem Reports (ETD)

Recent Appalachian Basin Geothermal Play Fairway Analysis estimated elevated heat flows in north-central West Virginia. This region provides an optimal and unique combination of elevated temperatures and flow necessary for geothermal development along with year-round surface demand for heating and cooling on the campus. Therefore, West Virginia University’s (WVU’s) Morgantown campus has been identified as a prime location in the eastern United States for the development of a geothermal direct-use heating and cooling application. The objective of this study was to perform a feasibility analysis for the development of a geothermal district heating and cooling (GDHC) system for WVU campus …

Overview Of Homechem: House Observations Of Microbial And Environmental Chemistry, Delphine K. Farmer, Marina E. Vance, Jon P. D. Abbatt, Andrew Abeleira, Michael R. Alves, Richard Corsi, Peter F. Decarlo, Allen H. Goldstein, Vicki H. Grassian, Lea Hildebrandt Ruiz, Jose L. Jimenez, Tara Kahan, Multiple Additional Authors

Mechanical and Materials Engineering Faculty Publications and Presentations

The House Observations of Microbial and Environmental Chemistry (HOMEChem) study is a collaborative field investigation designed to probe how everyday activities influence the emissions, chemical transformations and removal of trace gases and particles in indoor air. Sequential and layered experiments in a research house included cooking, cleaning, variable occupancy, and window-opening. This paper describes the overall design of HOMEChem and presents preliminary case studies investigating the concentrations of reactive trace gases, aerosol particles, and surface films. Cooking was a large source of VOCs, CO2, NOx, and particles. By number, cooking particles were predominantly in the ultrafine mode. Organic aerosol dominated …

The Cooperative Effects Of Channel Length-Bias, Width Asymmetry, Gradient Steepness, And Contact-Guidance On Fibroblasts’ Directional Decision Making, Quang Long Pham

Dissertations

Cell migration in complex micro-environments, that are similar to tissue pores, is important for predicting locations of tissue nucleation and optimizing scaffold architectures. Firstly, how fibroblast cells - relevant to tissue engineering, affect each other’s directional decisions when encountered with a bifurcation of different channel lengths was investigated. It was found that cell sequence and cell mitosis influence the directional choices that the cells made while chemotaxing. Specifically, the fibroblasts chose to alternate between two possible paths - one longer and the other shorter - at a bifurcation. This finding was counter-intuitive given that the shorter path had a steeper …

Experimental And Numerical Characterization Of Multiphase Subsurface Oil Release, Feng Gao

Dissertations

Subsurface oil release is commonly encountered in the natural environment and engineering applications and has received the substantial attention of researchers after the disastrous Deepwater Horizon Blowout oil spill in 2009. The main focus on the present research is to systematically study the hydrodynamics of underwater oil jet under a variety of conditions, including the effect of dispersant and different gas to oil ratios (GOR) by using experimental measurement as well as a Computational Fluid Dynamics (CFD) approach, from which the measured turbulent characteristics (e.g., velocity, turbulent kinetic energy, turbulence dissipation rate, etc.) of underwater oil jet are thoroughly examined …

Overcoming Conventional Modeling Limitations Using Image- Driven Lattice-Boltzmann Method Simulations For Biophysical Applications, Olufemi E. Kadri

Dissertations

The challenges involved in modeling biological systems are significant and push the boundaries of conventional modeling. This is because biological systems are distinctly complex, and their emergent properties are results of the interplay of numerous components/processes. Unfortunately, conventional modeling approaches are often limited by their inability to capture all these complexities. By using in vivo data derived from biomedical imaging, image-based modeling is able to overcome this limitation.

In this work, a combination of imaging data with the Lattice-Boltzmann Method for computational fluid dynamics (CFD) is applied to tissue engineering and thrombogenesis. Using this approach, some of the unanswered questions …

Interactions Between Polymer Nanoparticles And Blood Plasma Applied To Drug Delivery Systems, Mark Bannon

Theses

Targeted nanoparticle drug delivery has the potential to replace current forms of cancer therapy with previously unparalleled efficiency. Upon introduction into the human body, nanoparticles exhibit a substantial increase in diameter due to a biomolecular corona formation caused by interactions between blood plasma proteins and the nanoparticles. These interactions must be analyzed and understood for targeted delivery to reach its potential in both feasibility and efficiency.

To study the formation of the protein corona, polystyrene nanoparticles were incubated in vitro in goat blood plasma for 10-minute intervals, diluted to different degrees and then measured to obtain the hydrodynamic diameter of …

Performance Of C2H4 Reductant In Activated-Carbon-Supported Mnox-Based Scr Catalyst At Low Temperatures, Guangli Liu, Dongtai Han, Jie Cheng, Yongshi Feng, Wenbin Quan, Li Yang, Kozo Saito

Mechanical Engineering Faculty Publications

Hydrocarbons as reductants show promising results for replacing NH₃ in SCR technology. Therefore, considerable interest exists for developing low-temperature (< 200 °C) and environmentally friendly HC-SCR catalysts. Hence, C₂H₄ was examined as a reductant using activated-carbon-supported MnOx-based catalyst in low-temperature SCR operation. Its sensitivity to Mn concentration and operating temperature was parametrically studied, the results of which showed that the catalyst activity followed the order of 130 °C > 150 °C > 180 °C with an optimized Mn concentration near 3.0 wt.%. However, rapid deactivation of catalytic activity also occurred when using C₂H₄ as the reductant. The mechanism of deactivation was explored and is …

Stabilization Strategies Of Pt Catalysts Forproton Exchange Membrane Fuel Cells, Da-Ping He, Shi-Chun Mu

Journal of Electrochemistry

The low service lifetime of proton exchange membrane fuel cells (PEMFCs) is the main bottleneck for their commercial applications. One of the main factors is that the expensive metal Pt catalyst is easy to degradation under the harsh working environment of PEMFC (such as variable voltage, strong acidity, gas-liquid two-phase flow), which leads to the inevitable decay of the catalytic performance, thus, seriously restricting the lifetime of PEMFC. Therefore, the electrochemical stability of Pt-based electrocatalysts has become an important and hot topic to improve the PEMFC lifetime. In this paper, we review the recent development in enhancing the stability of …

The Pilot Application Of Electrochemical Impedance Spectroscopy On Dynamic Proton Exchange Membrane Fuel Cell, Jian-Wei Guo, Jian-Long Wang

Journal of Electrochemistry

By analyzing Electrochemical Impedance Spectroscopy (EIS) in applications of dynamic proton exchange membrane fuel cell (PEMFC), bottlenecks which restrict EIS tool development have been pointed out in this paper. Though the high-frequency resistance in EIS is largely accepted as cell inner-resistance, this can only be applied for cell with low current. The low-frequency resistance is difficult to be realized due to its relation with mass transfer. Furthermore, the improved Randles equivalent circuits are built up preliminarily, thus, penetrating into studies for mass transfer reaction, cell operation/degeneration, and high temperature fuel cell. Inspiringly, EIS is becoming an analyzing tool for stack …

Research Progress In Hydrogen Evolution Low Noble/Non-Precious Metal Catalysts Of Water Electrolysis, Yang Li, Zhao-Yan Luo, Jun-Jie Ge, Chang-Peng Liu, Wei Xing

Journal of Electrochemistry

Hydrogen energy technology with hydrogen as an energy carrier is gaining more and more attention due to its cleanliness and high energy density. Hydrogen fuel cell vehicles have been listed as one of the ultimate energy technologies in the 21st century. Among them, sustainable hydrogen production technology is a necessary prerequisite for the future development of hydrogen energy economy. Electrolyzed water technology driven by renewable resources represents an important way to support the sustainable development of hydrogen energy economy. The development and utilization of high activity, low cost hydrogen evolution catalysts is a key factor in improving the efficiency and …

Fuel Cell Performance Curve After Mea Optimization Structural Optimization Of Low Pt Membrane Electrode Assembly, Yan Rao, Shang Li, Fen Zhou, Tian Tian, Qing Zhong, Zhao-Hui Wan, Jin-Ting Tan, Mu Pan

Journal of Electrochemistry

Membrane electrode assemblies (MEAs) are the key component of proton exchange membrane fuel cell. For a long time, much attention has been paid to develop MEA technology. At present, the research, development and industrialization of fuel cell has entered a new era. More strict requirements for MEA, especially for the reduction of Pt loading with a challenging target of 0.125 mg·W^-1 have to be met. In this paper, the performance losses under low Pt loading are analyzed in terms of activation polarization, ohm polarization and mass-transfer polarization. It is proposed that research should be focused on the activity of …

Morphological Control Of Ptcu2 Octahedron And Oxygen Reduction Electrocatalytic Performance Of Ptcu For Fuel Cell, Long-Sheng Cao, Lei Wan, Zhi-Gang Shao, Hong-Mei Yu, Ming Hou, Bao-Lian Yi

Journal of Electrochemistry

Platinum acetylacetonate (Pt(acac)₂) and copper acetylacetonate (Cu(acac)₂) were co-reduced to prepare PtCu₂ octahedron alloy catalyst in N,N-dimethylformamiade by solvothermal method. The PtCu₂ showed lattice compression, and high ratio of non-oxidized Pt with high electronic binding energy. All those structural features contributed to weak adsorption strength of oxygen species on Pt and lower d-band centre position. The influence of structure-directing agent on morphology of PtCu alloy was systematically studied. In the half cell test, as a result of the uniform morphology and regular octahedron of PtCu₂ formed, the mass activity and area specific activity …

Effects Of So2 In Air On Performance Of Direct Methanol Fuel Cell, Bin Qin, Fen-Ning Jing, Xue-Jing Sun, Gong-Quan Sun, Hai Sun

Journal of Electrochemistry

Direct methanol fuel cells (DMFC) generally use oxygen as an oxidant. Contaminants such as sulfides and nitrides in the air can affect the performance of the DMFC. In this work, the effects of SO₂ on the performance of DMFC were investigated and the mechanism of poisoning was analyzed, by means of constant current discharge curve, polarization performance curve, cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). In the CV scan, the permeated methanol was oxidized at a low potential to eliminate its effect on the SO₂ poisoning behavior test. The results showed that the SO₂ poisoning resulted …

Recent Progress In Pt-Based Catalysts For Oxygen Reduction Reaction, Jing Li, Xin Feng, Zi-Dong Wei

Journal of Electrochemistry

One major challenge for a large-scale commercialization of the proton-exchange membrane fuel cells (PEMFCs) technologies that enable a shift to ‘zero-emission’ personal transportation, is the expensive and unstable Pt catalysts, which are mainly used to catalyze the sluggish kinetics of the oxygen reduction reaction (ORR) occurred on the air electrode of PEMFCs. Many research works have targets to improve the stability of Pt-based catalysts and to construct Pt/transitional metal alloys with low Pt loading amount. Herein, we provide a minireview for the Pt-based ORR catalysts based on our recent work, which covers a brief background introduction, the stability improvement of …

Fuel Cells Reactor For Chemicals And Electric Energy Cogeneration, Zhi-Lin Heng, Xiao-Zi Yuan, Yi-Mei Yin, Zi-Feng Ma

Journal of Electrochemistry

As an energy conversion device, fuel cells can efficiently convert chemical energy into electrical energy. With the developing of technology, it is used as a reactor to conduct the synthesis of high value-added chemicals while generating electrical energy. Having benefits such as mild reaction conditions, controllability of the reaction process, high selectivity of the product, as well as high efficiency of energy utilization, it is widely used in many fields such as preparation of high value-added industrial products, gas separation, water treatment, etc. This paper introduces the current trends and statuses of fuel cell reactors in the cogeneration of chemicals …

Progress Of Self-Humidifying Membrane Electrode Assembly For Low Temperature Proton Exchange Membrane Fuel Cell, Bin Chi, Yue-Kun Ye, Shi-Jie Jiang, Shi-Jun Liao

Journal of Electrochemistry

The self/non-humidification membrane electrode assembly(SH-MEA)is an important pathway towards the self- humidification fuel cell and plays a crucial role for the large scale commercialization of low temperature proton exchange membrane fuel cell (LT-PEMFC), because it not only can reduce the volume and complexity of fuel cell system, resulting in the decrease of the cost, but also can improve the output power density of the fuel cell system. Currently, the researches on the self-humidifying MEA of LT-PEMFC mainly focus on three aspects: the preparation of self-humidification proton exchange membrane, the construction of self-humidification catalyst layer, and the construction of composite self-humidifying …

A Review Of Proton Exchange Membrane Fuel Cell Catalyst Layer By Electrospinning, Yong Liu, Han Ding, De-Chun Si, Jie Peng, Jian-Bo Zhang

Journal of Electrochemistry

The limitation of catalyst layer for proton exchange membrane fuel cell (PEMFC) in cost, durability and performance constitutes the bottleneck for the commercialization of fuel cell vehicles. Electrospun catalyst layer, with high catalyst utilization, increased triple phase boundary (TPB) and triple phase channel (TPC), has been developed by many researchers. This paper reviews the research progress in the electrospun catalyst layer for PEMFC, combined with the author’s work. Firstly, the development progress of catalyst layer is summarized, and the catalyst layer is classified and analyzed based on its fabrication method and structure character. Next, the fabrication process, physical property characterization, …

Fe-N Doped Hollow Carbon Nanospheres Linked By Carbon Nanotubes For Oxygen Reduction Reaction, Ya-Lin Zhang, Chi Chen, Liang-Liang Zou, Zhi-Qing Zou, Hui Yang

Journal of Electrochemistry

The development of non-precious metal catalysts for oxygen reduction reaction (ORR) is essential for large-scale application of proton exchange membrane fuel cells. Herein, we present the in situ formed Fe-N doped hollow carbon nanospheres linked by carbon nanotubes composite, synthesized by using ZIF-8 as sacrificed template to form polydopamine (PDA) hollow nanospheres, followed by complexing with FeCl₃, high temperature heat-treatment and NH₃-etching. ZIF-8 was gradually decomposed simultaneously with PDA coating due to the loss of Zn²⁺ grabbed by PDA. NH3 etching resulted in the improved surface area, while the reducibility of NH₃ resulted in …

Facile Synthesis Of Pt-Cu Alloy Nanodendrites As High-Performance Electrocatalysts For Oxygen Reduction Reaction, Liu-Xuan Luo, Guang-Hua Wei, Shui-Yun Shen, Feng-Juan Zhu, Chang-Chun Ke, Xiao-Hui Yan, Jun-Liang Zhang

Journal of Electrochemistry

Structures and compositions have significant effects on the catalytic properties of nanomaterials. Herein, a facile etching-based method was employed to synthesize Pt-Cu nanodendrites (NDs) with uniform and homogeneous alloy structures for enhancing oxygen reduction reaction (ORR). The formation of dendritic morphology was ascribed to the etching effect caused by the oxidative etchants of the Br^-/O₂ pair. The atomic ratio of Pt/Cu in Pt-Cu NDs could be easily tuned by altering the ratio of the Pt/Cu precursors, without deteriorating the dendritic morphology. The most active carbon-supported Pt₁Cu₁ NDs (Pt₁Cu₁ NDs/C) exhibited the …

Acid Treated Carbon As Anodic Electrocatalysts Toward Direct Ascorbic Acid Alkaline Membrane Fuel Cells, He-Mu Chen, Chen-Xi Qiu, Yuan-Yuan Cong, Hui-Yuan Liu, Zi-Hui Zhai, Yu-Jiang Song

Journal of Electrochemistry

In order to improve the hydrophilicity and electrocatalytic activity, commercial carbon black (BP 2000) was subjected to acid treatment to obtain acid-treated carbon (ATC). The generation of rich oxygen-containing groups on the surface of the ATC was proved by X-ray photoelectron spectra (XPS), Fourier transform-infra red spectra (FTIR), thermogravimetric analysis (TG) and contact angle measurement. UV-vis spectra were firstly recorded to calculate activation energy (Ea) of ascorbic acid (AA) chemical oxidation in alkaline conditions by oxygen in air and the Ea value was determined to be 37.1 kJ·mol^-1. Additionally, electrochemical impedance spectra (EIS) were used to evaluate unprecedented …