Chemical Engineering Commons^™

Turning Down The Heat: Fine-Tuning Tempo-Modified Nanocellulose And Emim-Ac Ionic Liquid Membranes For Kidney Dialysis, Olivia Reid

Chemical Engineering Undergraduate Honors Theses

TEMPO modified nanocellulose membranes are utilized across various laboratory and industrial applications from protein purification to advancements in kidney dialysis. This study investigates the effect of varying coagulation temperatures on the morphology and transport properties of these membranes to enhance their performance for targeted filtration. It was hypothesized that higher temperatures would accelerate the solvent-nonsolvent exchange during phase inversion, resulting in larger pore structures. Conversely, lower temperatures were expected to slow solvent diffusion, yielding smaller, more uniform pores. The membranes[JH1]  were synthesized using 2,2,6,6-tetramethylpiperidinyl-1-oxyl (TEMPO) to improve selectivity and antifouling characteristics. Scanning electron microscopy (SEM) served as the primary …

Strengthening Kidney Dialysis One Membrane At A Time: Enhancing Tempo-Oxidized Nanocellulose And Ionic Liquid Membrane Strength Through The Variation Of Cosolvents, Bailey M. Butler

Chemical Engineering Undergraduate Honors Theses

Chronic kidney disease occurs when the kidneys lose the ability to effectively filter the blood, which causes waste build up. End-stage kidney disease (ESKD) is the most severe case of kidney disease and requires either dialysis or a kidney transplant. Hemodialysis, the most common form of dialysis, is an extremely time-intensive and physically burdensome process that is currently limited by membrane performance. The polysulfone (PSf) membranes that are widely used for dialysis today have many limitations, including fouling, toxin rejection, and essential protein loss. Recently, new membranes made from TEMPO-Oxidized nanocellulose dissolved in 1-ethyl-3-methylimidazolium acetate (EMIM-Ac) have shown promising characteristics, …

From Kernel To Carbon Footprint: Using Life Cycle Analysis To Teach Sustainability In Chemical Engineering, Neal Z. Kinney

Chemical Engineering Undergraduate Honors Theses

Many chemical engineering departments in the United States are currently lacking developed sustainability coursework, leaving many students without a developed understanding of topics such as life cycle analysis (LCA). [1] Therefore, there is a need for engaging and flexible educational tools that can be easily incorporated into course frameworks. This study develops an interactive learning module, expanding upon the work from Pollution Prevention Through Popcorn, a study developed by Rowan University. [2] The module combines experimental analysis of popcorn popping methods with life cycle assessment using OpenLCA to evaluate the environmental impacts of common types of popcorn packaging. Results of …

Shooting For The Stars: Stem Outreach Strategies Between 2nd And 7th Grade, Paige Miller

Chemical Engineering Undergraduate Honors Theses

Engineering and planetary science outreach programs are increasingly important as industries and research organizations face growing demand for STEM professionals. Despite the importance of these fields, many students receive little exposure to engineering careers during their early educational experiences. This honors thesis examines the effectiveness of interactive STEM outreach presentations designed for elementary and middle school students. Specifically, this study evaluates outreach activities centered on chemical engineering applications and the NASA M2M CO₂ regeneration project for Martian environments.

Two student age groups participated in this study: 2nd grade students at Butterfield Elementary School and 7th grade students at Woodland Junior …

A Baseline Study Of Artificial Intelligence Use Among Chemical Engineering Undergraduates At The University Of Arkansas, Natalie J. Erickson

Chemical Engineering Undergraduate Honors Theses

In recent years, artificial intelligence (AI) has shifted from a novel innovation to a tool used in daily life, particularly within higher education. While anecdotal evidence suggests high levels of student engagement with AI, empirical data regarding usage patterns remains limited. This baseline study investigates AI integration among undergraduate chemical engineering students at the University of Arkansas. Through an anonymous survey (N=68; comprising 20 freshmen, 14 sophomores, 16 juniors, and 18 seniors), researchers assessed usage frequency, student comfort levels, and their evolving relationship with AI tools. The findings reveal that 75% of respondents utilize AI for coursework at least once …

Polymer Charge Effects On Scaling In Membrane Distillation, Lucia Milans Del Bosch

Chemical Engineering Undergraduate Honors Theses

This research evaluates the effectiveness of polymeric inhibitors at suppressing scaling during direct contact membrane distillation (DCMD). Anionic polyacrylic acid (PAA), neutral polyethylene glycol (PEG), and cationic polyethyleneimine (PEI), were investigated. Experiments were conducted using both hypersaline single-salt and multi-component mixed-salt feeds to determine how the presence of different ions influences performance. Results from single-salt experiments showed that PAA and PEG effectively maintained permeate flux through chelation and steric hindrance, respectively, while PEI caused rapid membrane failure due to interfacial aggregation and pore wetting. In complex mixed-salt solutions, PEG was the additive, maintaining a steady flux with only a 7.33% …

Surface-Functionalized Silica Nanoparticles For Enhanced Bioavailability In Ophthalmic Mucoadhesive Drug Delivery Applications, Kaylee M. Drake

Chemical Engineering Undergraduate Honors Theses

This study investigates the stimuli-responsive behavior of porcine gastric mucin (PGM) as a model for the conjunctival mucous membrane of the human eye to optimize mucoadhesive ophthalmic drug delivery. As a versatile biopolymer, PGM has a dynamic matrix structure that functions as a selectively permeable barrier, regulating transport across mucosal membranes. To improve drug bioavailability and retention in ocular treatments, silica nanoparticles (SiNPs) were modified with varying surface functional groups and incorporated into the mucin at different physiological pH levels to examine the resulting microstructural changes. Leveraging the amphiphilic and negatively charged characteristics of mucin, positively charged and hydrophobic SiNPs …

Cationic Polymer-Grafted Magnetic Nanoparticles For Enhanced Removal Of Anionic Dyes From Wastewater, Joia A. Traver

Chemical Engineering Undergraduate Honors Theses

Water scarcity and pollution are escalating global challenges, with textile industry wastewater often enriched with toxic dyes posing significant risks to environmental and human health. These contaminants increase turbidity, reduce dissolved oxygen levels, and ultimately impair aquatic ecosystems. This thesis focuses on the remediation of dye-contaminated water using nanoscale polymeric adsorbents. Methyl orange, a common anionic dye widely used in textile and leather industries, was selected as the model contaminant due to its terminal sulfonate group, which enables strong electrostatic and hydrogen-bonding interactions with cationic functional materials.

In this work, magnetic nanoparticles grafted with cationic polymers were synthesized and evaluated …

Performance Of Zirconia-Based Catalysts For Cold Plasma-Assisted Dry Methane Reforming, Levi Pile

Chemical Engineering Undergraduate Honors Theses

This study investigates the performance of zirconia-based catalysts in non-thermal plasma (NTP)–assisted dry methane reforming (DMR) for synthesis gas (syngas) production. This work explores an alternative pathway for converting carbon dioxide and methane into valuable products under milder conditions than conventional thermal processes. Experiments were conducted in a radiofrequency plasma reactor to evaluate the effects of plasma power, feed flow rate, and reactant ratios on conversion efficiency. The performance of plasma-only conditions was compared with packed-bed systems using zirconia catalysts. Results show that plasma-only systems achieved modest conversion rates (~16.5% for CH₄ and ~12.0% for CO₂), while …

Predicting Personalized Myocardial Fibrosis Response Patterns Using A Mechanistic Signaling Network Model, Jared Noel

Chemical Engineering Undergraduate Honors Theses

Myocardial fibrosis is a key driver of heart failure progression and exhibits substantial patient-to-patient variability, complicating the development of effective personalized therapies. In this study, we present an integrated computational framework that combines a mechanistic signaling network model with patient-specific proteomic data to predict individualized fibrotic responses and therapeutic strategies. Using proteomic measurements from the Framingham Heart Study, we generated personalized baseline states and performed systematic in silico perturbation screens to evaluate candidate drug targets across 132 signaling nodes. Results reveal that while global network response structure is conserved, therapeutic efficacy varies widely between patients in both magnitude and breadth, …

Electrochemical And Mechanical Evaluation Of Cellulose Acetate Electrolyte Films As A Function Of Polyetherimide And Polyethylene Glycol Additives For Supercapacitor Applications, Chase E. Golden

Chemical Engineering Undergraduate Honors Theses

Polymer electrolytes for supercapacitor applications require a balance between mechanical robustness and electrochemical performance. In this study, cellulose acetate (CA) films were modified with additives such as polyetherimide (PEI) and polyethylene glycol (PEG) to test how compositional changes influence mechanical performance, ionic conductivity, and electrochemical charge storage. Films were cast using phase inversion, soaked in a 1 M NaCl aqueous solution, and characterized using Fourier-transform infrared spectroscopy (FTIR), electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), and tensile testing. Films were also evaluated based on fluid uptake for insight into electrolyte retention.

Characterizations show that the addition of PEI increased ionic …

Demonstration Of The Relationship Between Irwin Spire Quantity And Boundary Layer Depth In The Chemical Hazards Research Center Wind Tunnel, Jace D. Beckwith

Chemical Engineering Undergraduate Honors Theses

Atmospheric Dispersion Models (ADMs) are computer-based simulations used to model gas releases for enforcing regulatory compliance, designing facilities, and responding to emergencies. Because ADMs rely on complex mathematical models, they require experimental validation to ensure accuracy. Wind tunnels offer a controlled, repeatable method for gathering validation data. The Chemical Hazards Research Center (CHRC) at the University of Arkansas operates an ultra-low speed wind tunnel for this purpose. A key feature of this tunnel is its simulated Atmospheric Boundary Layer (ABL). The simulated ABL is a turbulent layer in which wind speed increases logarithmically with height from near zero at the …

Design Of Aluminum-Air Battery Systems And Optimization Of Cetyltrimethylammonium Bromide And 8-Hydroxyquinoline Additives In Alkaline Electrolytes, Steve Chen

Chemical Engineering Undergraduate Honors Theses

The first portion of this thesis focuses on the design and component optimization of aluminum-air batteries to power a car for the Chem-E-Car competition. A range of separators, cathodes, and current collectors was evaluated to determine the optimal configuration for maximizing output. The resulting system consisted of 1000 series aluminum as the anode, cellulose separators saturated in 1 M potassium hydroxide as the electrolyte, and composite PVDF and graphite as the cathode. The improved batteries achieved a power density of 2.14 x 10^-4 W/cm² and were utilized for the Chem-E-Car competition. The second portion of the thesis investigates …

An Efficient Implementation Of Gibbs-Duhem Integration For Solid-Liquid Phase Coexistence In Binary Lennard-Jones System With Relevance To Aav Capsid Separation, Muhi Muntaka

Graduate Theses and Dissertations

Gene therapy using adeno-associated viruses (AAVs) holds promise for treating genetic diseases, but high manufacturing costs limit its widespread use. A major challenge is separating functional (full) AAV capsids from non-functional (empty) ones, which are produced in similar amounts and have nearly identical structures. Conventional purification methods, such as density gradient ultracentrifugation and chromatography, face drawbacks like low yield, poor scalability, and high cost, often requiring multi-step processes. Recently, selective crystallization has emerged as a promising alternative, offering improved efficiency, scalability, and product quality. However, optimizing this method requires a deep understanding of thermodynamic phase behavior in multicomponent systems. In …

A Probabilistic Approach To Multiscale Simulation: Evaluating Machine-Learned Backmapping Models Of Diphenylalanine, Sage Paschall

2026 Research Poster Competition

Diphenylalanine (FF) has demonstrated the tendency to form several nanostructures, a subset of which are electrically conductive and have exciting potential applications in biotechnology and nanoelectronics. However, the exact mechanisms underlying this self-assembly process remain largely ambiguous. Atomistic-scale molecular dynamics (MD) simulations allow for the evaluation of atomic-level interactions crucial in understanding the driving thermodynamic forces behind self-assembly, but are too computationally expensive to span the necessary timescale to observe the self-assembly process in action. Coarse-grained (CG) models allow for simulation at the appropriate timescale but come at the cost of vital atomistic detail. It is therefore important to develop …

Experimental Measurement Demonstration Of Initial And Steady-State Heights Of A Co2 Vertical Jet Fountain In Still Air, Brock Mcrae

Chemical Engineering Undergraduate Honors Theses

Atmospheric releases of heavier-than-air gases pose acute near-field hazards in low wind, yet the near-source behavior of vertical dense-gas jets in still air is sparsely documented. This thesis demonstrates a repeatable laboratory method for measuring the initial and steady-state rise heights of a carbon dioxide (CO₂) jet issued vertically from a floor nozzle in the CHRC ultra-low-speed wind tunnel under still-air conditions. Controlled mixtures (pure CO₂, 50/50 CO₂-air, 25/75 CO₂-air) were released at four flow rates (75, 100, 125, 150 LPM) with five repeats per condition. A fixed camera and tape-measure scale enabled video extraction of jet height using Kinovea …

Calibration And Validation Of Cyclic Stretching Platform For Stiffness Testing Of Engineered Heart Tissue, Jillian Welsh

Chemical Engineering Undergraduate Honors Theses

Cardiac fibrosis (CF) is a major contributor to the high mortality rate of heart failure which affects over 23 million people worldwide. CF involves cardiac fibroblasts depositing extracellular matrix, made primarily of collagen type I, which stiffens the heart walls over time. As testing new drugs for CF is deterred by the high cost and time required for animal and clinical trials, this research helps to solve the problem by providing an in vitro platform to study fibrosis.

The work involved creating tissues containing human cardiac fibroblast (HCFB) cells. Spring testing was conducted to determine the force applied by the …

Advanced Membrane Methods For Treatment Of Toxic Contaminants And Education Of Early-Career Researchers, Thomas Mckean Iii

Graduate Theses and Dissertations

Membrane technologies are attractive as they are linearly scalable and often require lower operating costs compared to other technologies. One area where they are particularly effective is the treatment of water contaminated with toxic substances. The simplicity of this removal mechanism provides reliable performance capable of meeting stringent removal requirements. However, membrane fouling is a major challenge that often limits their commercial viability. This research sought to investigate novel approaches to pretreatment and membrane modification to overcome fouling and high operating pressures. In addition, membrane separation processes can often be developed into simple yet educational experiments that are ideal for …

Novel Electroactive Polymer Actuators Using All-Polyelectrolyte Poly(Ionic Liquid) Ionogels, Kayla Foley, Iwei Chu, Keisha B. Walters

Chemical Engineering Faculty Publications and Presentations

Poly(ionic liquid)-based ionogels are excellent all-poly(electrolyte) candidates for electroactive actuation applications, but investigation of their actuation behavior and ionogel properties has largely been limited to styrenic block copolymers. In this work, ionogels were prepared from a novel poly(ionic liquid) (PIL) block copolymer, poly[(2-dimethyl amino) ethyl methacrylate)]-block-poly[4-vinylbenzyl-3-butyl imidazolium bis(trifluoromethylsulfonyl)imide] (PDMAEMA-b-PVBBImTf(2)N) combined with an ionic liquid, 1-butyl-3-methyl imidazolium tetrafluoroborate (C(4)C(1)ImBF(4)), at weight percentages between 0 to 40 wt%. Under a low applied voltage (4 V DC) microscale actuation was achieved for films prepared from the neat PDMAEMA-b-PVBBImTf(2)N block copolymer, as well as its corresponding 10 wt% ionogel; this result critically expands the …

Aminated Phenolated Lignin For Effective Anionic Dye Removal For Water Remediation, David Chem, Samantha Glidewell, Fatema Tarannum, Keisha B. Walters

Chemical Engineering Faculty Publications and Presentations

Lignin, a renewable biopolymer sourced from plant cell walls, is gaining attention due to its extensive availability from natural resources, native functional groups, low cost, and biodegradability in various applications. In recent years, lignin and its derivatives have been utilized as adsorbents, flocculants, and sterilants in a broad range of applications, including wastewater treatment and sustainable packaging. The growing global demand for clean water-driven by rapid industrialization, urban expansion, and agricultural intensification-has made effective wastewater treatment a pressing environmental priority. In this effort, a dual-functionalization strategy to transform raw lignin into a high-performance adsorbent for the removal of hazardous anionic …

Simulation Of Photochemical Effects On Air Quality, Grace Li

Chemical Engineering Undergraduate Honors Theses

Nitrogen dioxide (NO₂) and ozone (O₃) are both EPA criteria air pollutants in the troposphere, largely generated by combustion and therefore present in significant concentrations in urban areas. Sunlight facilitates chemical reactions between pollutants and ambient air. Aerosols modulate the amount of available energy required to drive such photochemical reactions, ultimately impacting air quality. Simulating photolysis rates with FastJX software is a resource-efficient strategy to study how these aerosols can affect air quality.

Polymer-Enhanced Nanopore Sensing, Eugene Gyasi Agyemang

Graduate Theses and Dissertations

The resistive pulse technique characterizes single analytes by detecting fluctuations in the ion current as they pass through a narrow orifice connecting two electrolyte-filled chambers, each containing a single electrode. The amplitude, shape, frequency, and duration of these fluctuations primarily provide information about the analyte’s size, shape, concentration, and net surface charge, respectively. One configuration for resistive pulse measurements is of an electrolyte-filled nanopipette immersed in a bath, where the nanopipette tip acts as the nanoscale orifice. It was previously shown that incorporating the large quantities polymer polyethylene glycol (PEG 8K, 50% w/v) into the external electrolyte bath dramatically enhanced …

Wind Tunnel Model Of The Jack Rabbit Ii Field Experiments In The Mock Urban Array: Part 2. Approach Wind Conditions And Particle Image Velocimetry Measurements Of Simulated Chlorine Releases, Paulo V. Lopez, Thomas O. Spicer, Chad T. Smith

Chemical Engineering Faculty Publications and Presentations

The Jack Rabbit II (JR-II) Mock Urban Environment field test was reproduced in a 1:50 scale physical model in the wind tunnel at the Chemical Hazards Research Center of the University of Arkansas. The agreement of the approaching wind characteristics between field test and model was verified using 3D Laser Doppler Velocimetry (LDV). 2D Particle Image Velocimetry (PIV) tests were conducted in the model to obtain velocity measurements in the MUE. Velocity measurements taken before and during a simulated chlorine release were compared. PIV results show the general flow complexity in the last rows of the MUE and the impact …

Leveraging Oxygen Mobility With Zirconia In Low-Temperature Plasma For Enhanced Methane Reforming To Syngas, Fnu Gorky, Levy Pile, Grace Jones, Apolo Nambo, Mourad Benamara, Maria L. Carreon

Chemical Engineering Faculty Publications and Presentations

Despite extensive efforts to optimize the single-step production of syngas, hydrocarbons, and oxygenates via plasma catalysis, several challenges remain unresolved. In particular, understanding the various reaction pathways is hindered by the complexity of the reactions and the diverse range of chemical products formed. In this study, our main objective is to evaluate and compare the influence of zirconia on reaction pathways, methane (CH4) and carbon dioxide (CO2) conversions (%), and syngas selectivity (%) relative to the plasma-only route. Experiments were conducted at a low radio-frequency plasma power of 50 Watts without external heating. The results demonstrated significantly enhanced conversions of …

Optimized Electrocoagulation Pre-Treatment For Fouling Reduction During Nanofiltration Of Lake Water Containing Microcystin-Lr, Thomas Mckean, Chidambaram Tharmaraiselvan, Sarah Do, S. Ranil Wickramasinghe

Chemical Engineering Faculty Publications and Presentations

Microcystin-LR (MCLR) is a toxin produced by harmful algal blooms that is emerging as a threat to drinking and recreational water systems worldwide. Nanofiltration (NF) is an effective technique for purifying contaminated water sources; however, membrane fouling caused by coexisting organic matter limits the practicality of the process. This research studies the use of an electrocoagulation (EC) pretreatment to limit fouling during the NF process. Water for this study was taken from Lake Fayetteville, a local body of water where MCLR concentrations have been recorded to be >15 µg/L. EC was performed using polyaluminum chloride as a background electrolyte at …

Personalized Model Of Cardiac Fibroblast Signaling Using Patient-Specific Data, Elizabeth A. Schuler

Chemical Engineering Undergraduate Honors Theses

Heart disease is the leading cause of death worldwide for both men and women, and cardiac fibroblasts are critical to heart form and function. Essential roles of cardiac fibroblasts include cell-cell communication, cell-cell signaling, and synthesizing and degrading the extracellular matrix (ECM), which controls structural support and tissue repair of the heart. Abnormal fibroblast signaling can lead to negative impacts, including fibrosis, impaired heart function, and inflammation. A computational model of cardiac fibroblast signaling on Netflux and MATLAB software was adapted and utilized to determine the effect of patient-specific levels of cytokines, hormones, growth factors, peptides, and membrane tension on …

Multifunctional Pvdf Ionogels With Magnetic Nanoparticles For Electroactive And Magnetic Actuation, Alfredo Carrillo Valverde

Chemical Engineering Undergraduate Honors Theses

The fast development of compact and multifunctional electronics has driven interest in smart materials capable of responding to multiple stimuli. Ionogels, polymers that have been swollen with ionic liquids (IL), offer several favorable electrochemical and thermal properties due to their intrinsic ion conductivity, wide electrochemical window, non-flammability, and high thermal stability. However, their poor mechanical properties (e.g., modulus and strength) limit their use in applications. In this work, multifunctional PVDF ionogel composites were made by blending magnetically responsive iron oxide nanoparticles (Fe₃O₄ MNPs) into the polymer matrix. The influence of MNP concentration (9-21 wt%) on composition, ionic …

Using Gaussian Process Regression To Learn Thermodynamic Equations Of State With Uncertainty Quantification, Austen T. Lee

Chemical Engineering Undergraduate Honors Theses

This study investigates the use of derivative-informed Gaussian Process (GP) models to estimate thermodynamic behavior across temperature and density by building a Helmholtz-based equation of state. Argon, a stable monatomic gas, was chosen as a case study within the vapor region. The GP model was trained using values of experimentally measurable properties found by taking first and second derivatives of the original potential function. Results show that while the GP model offered uncertainty quantification and informed thermodynamic behavior, it predicted values that deviated from the ground truth depending on the property. The model exhibited high confidence in regions with substantial …

Development And Validation Of A Computational Fluid Dynamics Model Using Wind Tunnel Experiments, Savanah G. Godwin

Chemical Engineering Undergraduate Honors Theses

A gas release computational fluid dynamics model was developed and validated using a previous wind tunnel experiment conducted by Daniel Williams. This simulation was modeled using CHEM software, and based on experimental conditions used in the University of Arkansas’ Chemical Hazard Research Center’s wind tunnel. These include ultra-low wind speeds, working in the atmospheric boundary layer, and using finite release durations with a neutrally buoyant gas. The simulation was developed in two phases: inflow and release. The inflow phase consisted of the development of the atmospheric boundary layer. The data from the simulation aligned well with the wind tunnel data. …

Modeling Cell Buildup And Release In An Ultrafiltration Cartridge, Holiday B. Derosier

Chemical Engineering Undergraduate Honors Theses

While membrane filtration has improved greatly and has been incorporated into many modern practices, there isn’t much data on material exchange in and out of the lumen and how that effects the overall efficiency of the process. This data may help to accurately measure the reliability and efficiency of a filtration membrane system, which can lead to improvements in filtration sustainability, process lifespan, and product quality.

This project aims to model the material balance within a perfusion bioreactor ultrafiltration system in MATLAB, with a focus on bioreactors and cell buildup and release from the lumen. The results of this study …