Chemical Engineering Commons^™

Deoxygenation Of Palm Fatty Acid Distillate To Green Diesel Over Molybdenum Nitride And Carbide-Based Catalysts In A Trickle-Bed Reactor, Wanwipa Leangsiri

Chulalongkorn University Theses and Dissertations (Chula ETD)

In this present work, the deoxygenation of palm fatty acid distillate (PFAD) to green diesel over γ-Al2O3 supported bimetallic CoMo and NiMo carbide and nitride catalysts was conducted in a trickle bed reactor. The catalysts were prepared by a single-step decomposition method of mixture containing hexamethylenetetramine and corresponding metal salts in presence of hydrogen and nitrogen for carbide and nitride forms, respectively at 700 oC. The prepared catalysts were characterized by XRD, XPS, N2-sorption, SEM/EDX and TGA techniques. The catalyst performance was evaluated at a temperature of 330 °C, hydrogen pressure of 5 MPa, LHSV of 1 h−1, and H2/feed …

Data Analytics Of Natural Gas Injection Enhanced Oil Recovery For Unconventional Reservoirs, Ali Waqar

Masters Theses

"Unconventional Enhanced Oil recovery, via the injection of natural gas has attracted great attention, as studies and projects have shown to be promising. An overview of pertinent studies has been carried out. Core Scale Laboratory Experiments, Core Scale Simulation, Field Scale simulation and pilot projects are analyzed. Data is collected for Core, Reservoir, Operational, and recovery information. Thereafter, Data analysis techniques are applied to identify data ranges, distributions, trends, relationships, and to eventually reach conclusions.

Huff and Puff injection is the preferred mode of injection, delivering most promising results for unconventional reservoirs. Across all the studies, with increase in amount …

Evaluation Of Eor Potential Of Low Salinity Polymer In Enhancing Heavy Oil Recovery On The Alaska North Slope, Shize Yin

Masters Theses

"Alaska's North Slope (ANS) contains vast amount of viscous oil resources that have not been extracted. This study focuses on the investigation over the potential shown by low-salinity polymer flooding in improving the recovery of ANS heavy oil through laboratory experiments.

At the beginning, coreflooding experiments were performed with silica sandpacks. The synergy between low-salinity water flooding and polymer flooding was proved, and the low-salinity polymer showed a better performance than the normal-salinity polymer. Further, the sandpacks prepared with formation sand from an oilfield on the ANS was then employed so as to simulate the reservoir condition. A series of …

Experimental And Computational Characterization Of Sodium Nitrate @ Silica Nano Capsules For Thermal Energy Storage Applications, Wataru Hashimoto

Graduate Research Theses & Dissertations

In this investigation, a nanocapsule composed of a sodium nitrate core and a silicon dioxide shell is synthesized, characterized, and analyzed utilizing a mixture of analytical and computational tools. The sol-gel method was selected as the process of nanoencapsulation. Analytical characterization techniques employed in this investigation include differential scanning calorimetry (DSC) to measure melting temperatures and enthalpies of fusion, dynamic light scattering (DLS) to calculate particle size distributions, scanning electron microscopy (SEM) to analyze surface characteristics, transmission electron microscopy (TEM) to perform shell characterization, and energy dispersive X-ray spectroscopy (EDS) to determine chemical composition. Preliminary results indicated a decrease in …

Fundamental Study Of Supported Metal Catalysts Prepared By Metal In Lithium Solution For Energy Science, Haiping Xu

Graduate Research Theses & Dissertations

Electrochemical carbon dioxide reduction reaction (CO2RR) is a promising technique for energy conversion and storage from intermittent electricity sources (ie. wind and solar). By coupling electrochemical CO2 reduction (CO2R) to a renewable energy source atmospheric CO2 could be converted back into a fuel such as ethanol, or a commodity chemical such as ethanol or acetic acid. These products could then be consumed for energy or used to generate more valuable chemical products effectively removing CO2 from the atmosphere. To commercialize this process, it is highly desired to prepare catalysts that selectively reduce CO2 at low overpotential with long durability. Research …

Bimetallic Nanoparticles Integrated Membranes For Groundwater Remediation: Synthesis, Characterization And Applications, Hongyi Wan

Theses and Dissertations--Chemical and Materials Engineering

The detoxification of chlorinated organics from groundwater, such as trichloroethylene (TCE), tetrachloroethylene (PCE), polychlorinated biphenyl (PCB) and carbon tetrachloride (CTC), is a challenging area. Reductive dechlorination has been investigated using iron and iron-based nanoparticles, such as bare Fe, sulfidized Fe (S-Fe) and palladized Fe (Pd-Fe). However, issues including particle agglomeration, difficulties in recycling and particle leaching have been reported to hinder the application and wide usage of these techniques. The integration of nanoparticles and membranes can address these issues because of the large surface area, stability, and the potential for versatile functionalities. In this study, commercial polyvinylidene difluoride (PVDF) microfiltration …

Characterization And Electrochemical Performance Of Dopamine-Sensitized Titania Thin Films, Joshua Garay

Theses and Dissertations--Chemical and Materials Engineering

Sensitization of mesoporous titania films with dopamine and polydopamine for visible light photoelectrochemical activity is investigated. Sensitization effectiveness is compared with 8 mM dopamine solutions of varying pH (acidic, basic, and neutral), as well as with a basic polydopamine solution. Vibrational changes due to dopamine attachment are determined from detached powders by Fourier-transform infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA) is used to quantify organics attached. X-ray photoelectron spectroscopy (XPS) of intact films probes the chemically induced charge shift from dopamine attachment. Cyclic voltammetry identifies the irreversible dopamine oxidation and tin reduction voltages. Finally, chronoamperometric curves are used to compare …

Effect Of Silica Nanoconfinement Of Lipid Bilayers On Its Phase Transition And On The Colloidal Stability Of Silica Nanoparticles, Aniruddha Atul Shirodkar

Theses and Dissertations--Chemical and Materials Engineering

In this work, we incorporated 4-(N-Boc-aminometyl) phenylboronic acid (BA), at different concentrations, into 1,2-dipalmitoyl-sn-glycero-3- phosphocholine (DPPC) bilayers confined within nanopores of two different mean pore diameters of 7.4 nm and 11.7 nm of micron sized silica particles. The confinement of DPPC into nanopores resulted in the depression in the main phase transition temperatures compared to the liposomal system. The addition of BA was found to induce disruptions in the acyl chains of the lipid molecules at all concentrations of the solute. The lipid bilayer cooperativity was found to be higher in the confined systems compared to the liposomal systems despite …

Silica Nanoporous Confinement Effects On Ionic Liquid Properties For Better Design Of Small Molecule Separation, Electrochemical Devices And Drug Delivery, Yuxin He

Theses and Dissertations--Chemical and Materials Engineering

Silica nanoconfinement provides a high level of control of ionic liquids (ILs) in localizing catalysts, creating distinct environment for tuning reactivity and controlling the partition of solvents, reactants and products. Silica thin films with two different pore sizes (2.5 nm and 8 nm) were synthesized to study the effect of nanopore confinement on ionic liquids 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM][PF₆]), and 1-butyl-3-methylimidazolium chloride ([BMIM][Cl]). Silica thin films with accessible 8 nm pore diameters were synthesized using evaporation-induced self-assembly (EISA) with Pluronic P123 as templating surfactant on a chemically neutral modified substrate. The silica films with similar orthogonal aligned mesostructured but …

Nanostructured Metal Thin Films As Components Of Composite Membranes For Separations And Catalysis, Michael J. Detisch

Theses and Dissertations--Chemical and Materials Engineering

Novel metallic thin film composite membranes are synthesized and evaluated in this work for improved separations and catalysis capabilities. Advances in technology that allow for improved membrane performance in solvent separations are desirable for low molecular weight organic separation applications such as those in pharmaceutical industries. Additionally, the introduction of catalytic materials into membrane systems allow for optimization of complex processes in a single step. By adding a nanostructured metallic thin film to its surface, a polymer membrane may be modified to exhibit these improved properties. Using magnetron sputtering, thin metal films may be deposited on commercially available membranes to …

A Framework For Heterologous Biosynthesis Of Natural Products In Mammalian Cells Via Polymer-Mediated Transfections, Logan Warriner

Theses and Dissertations--Chemical and Materials Engineering

With the promise to treat a multi-faceted list of serious inherited and acquired diseases, such as cancer, neurodegenerative and infectious diseases, and inherited genetic indications, gene therapy has continued to push the boundaries of traditional medicine since its earliest implementation. While much progress has been made, clinical success has largely remained elusive. Immunogenicity, difficulty producing commercially relevant quantities, and having a limited genetic payload still limits the ability of viruses to act as directed delivery agents for genetic material. As such, researchers have turned to cationic synthetic materials as a means of delivering nucleic acids, which can circumvent the immune …

Microfiltration Membrane Pore Functionalization Approaches For Chloro-Organic Remediation To Heavy Metal Sorption, Mohammad Saiful Islam

Theses and Dissertations--Chemical and Materials Engineering

Microfiltration polyvinylidene fluoride (PVDF) membranes have distinct advantage for open structure in terms of high internal surface area and ease of access in the pore domain. Functionalization of PVDF membranes with different functional groups (-COOH, -OH, -SH) enables responsive (pH, temperature) properties to membrane, tuning of effective pore size, controlling permeate flux. PVDF microfiltration membrane functionalization with suitable responsive polymer such as poly acrylic acid (PAA) to incorporate carboxyl (-COOH) group enables further modification of functionalized PAA-PVDF membranes for different application ranging from catalysis, bio reactor to heavy metal sorption platform. As a catalytic reactor bed, this PAA-PVDF membranes are …

The Development Of Temperature And Ph Responsive Hydrogels And Membranes For Selective Sorption Of Perfluoroorganics And Nanoparticle Integrated Catalytic Degradation Of Pcb, Anthony Saad

Theses and Dissertations--Chemical and Materials Engineering

The functionalization and use of responsive and catalytic polymeric membranes and materials were explored for contaminant capture and degradation. While membranes have a wide variety of uses across multiple industries, the inclusion of materials that are temperature and pH responsive in the membrane pore domain yields a wide range of applications and possibilities for water treatment. Temperature and pH responsive polymers, as well as controlled nanostructured materials, were synthesized in membrane pores for advanced adsorption-desorption and catalytic treatment of emerging organic contaminants in water. In this study, supported by the NIEHS, poly-N-isopropylacrylamide (PNIPAm) was used as a model thermo-responsive polymer, …

A Thermodynamic And Feasibility Study Of Green Solvents For The Fabrication Of Water Treatment Membranes, Xiaobo Dong

Theses and Dissertations--Chemical and Materials Engineering

Nonsolvent induced phase separation (NIPS) has been widely used to fabricate polymeric membranes. In NIPS, a polymer is dissolved in a solvent to form a dope solution, which is then cast on a substrate and immersed in a nonsolvent bath, where phase inversion occurs. Petroleum-derived organic solvents, such as N-Methyl-2-Pyrrolidone (NMP) and Dimethylacetamide (DMAc), have been traditionally used to fabricate polymeric membranes via NIPS. However, these solvents may have negative impacts on environmental and human health; therefore, using greener and less toxic solvents, preferably derived from biomass, is of great interest to make membrane fabrication sustainable. In this dissertation, two …

Heart Tissue Reconstruction By Light-Controlled Cell Adhesion, Patterning And Alignment On Decellularized Scaffolds, Cong Li

Theses and Dissertations--Chemical and Materials Engineering

There is an urgent demand for engineered tissues and organs because of extremely limited donor tissues available for transplant. The challenge of tissue rejection has motivated many researchers to try to remove all of the cells from a heart and then add back in patient matched cells. These recellularized hearts are a promising avenue towards a functional bioartifical heart that is less likely to be rejected. Decellularized extracellular matrix (ECM) scaffolds generated from animal hearts do not have the cellular components that elicit immune rejection in patient, and they also preserve the native heart tissue structure. While decellularization techniques are …

Polymeric Nanocomposite Membranes With Phosphorene Based Pore Fillers For Fouling Control, Joyner Eke

Theses and Dissertations--Chemical and Materials Engineering

Phosphorene is a two-dimensional material exfoliated from bulk phosphorus. Specifically, relevant to the field of membrane science, the band gap of phosphorene provides it with potential photocatalytic properties, which could be explored in making reactive membranes able to control the accumulation of compounds on the surface during filtration, or fouling. Another reason phosphorene is a promising candidate as a membrane material additive is due to its catalytic properties which can potentially destroy foulants on the membrane surface.

The first goal of this study was to develop an innovative and robust membrane able to control and reverse fouling with minimal changes …

Thermal / Structural Analysis Of The Hb 650 Thermal Shield, Gerald J. Smith

Graduate Research Theses & Dissertations

Fermilab’s PIP-II project’s superconducting linear accelerator (Linac) will drive the next generation of particle accelerators through a revolution in beam intensity. Key to beam intensification are the high efficiencies of niobium-tin superconducting radiofrequency (SRF) cavities operating at cryogenic temperatures near 5 Kelvin. A multifaceted approach is employed to achieve and maintain the extreme temperature. Vacuum provides the first barrier to thermal convection. Physical thermal intercept zones further isolate the exterior shell vacuum vessel at 300 Kelvin from the supercooled beamline. The first thermal intercept lies just inside the exterior vacuum vessel forming the 40 Kelvin zone. This 40K thermal shield …

Formulation Strategies To Enhance Solubility And Permeability Of Small Molecules For Drug Delivery Applications, Pradeep Kumar Bolla

Open Access Theses & Dissertations

All the new chemical entities/drug molecules intended for therapeutic use must be administered using an appropriate delivery system/dosage form to achieve maximum bioavailability. However, designing a drug delivery system is complex as several factors such as lipophilicity, molecular mass, crystallinity, ionic charge, polymorphic forms and hydrogen bonding) affect the solubility and permeability of these molecules. Biopharmaceutics drug classification system (BCS) categorizes the existing drugs into four classes based on the aqueous solubility and membrane permeability and it is reported that >70% of the drugs are poorly soluble and belong to BCS class II and BCS class IV. Several physical, chemical …

Pharmaceutical Manufacturing In The 21st Century: Identification And Analysis Of Key Elements, Robert N. Mills

Honors Program: Senior Projects (Public)

The availability of quality pharmaceutical products impacts the lives of the global population on a daily basis. The importance of product availability and quality within pharmaceutical manufacturing requires that quality systems put into place are capable of accurately and robustly capturing the quality compliance, or lack thereof, of the various stages of production. This review intends to analyze current expert-recommended best practices within key elements of a pharmaceutical manufacturing quality control system and provide recommendations throughout. The quality elements discussed include Quality by Design method validation, necessary equipment determination, and equipment qualification, followed by documentation control and data flow.

Optimization And Validation Of The Neurolux Wireless Optoelectronics System For Optogenetics, Karis Courey, Su Hyun Lee Ph.D., Adam Smith Ph.D., Nicholas Cilz Ph.D., Sarah K. Williams Avram Ph.D., Adi Cymerblit-Sabba Ph.D., June Song, Nicholas Leipzig Ph.D., W. Scott Young M.D., Ph.D.

Williams Honors College, Honors Research Projects

Utilizing light and genetic engineering, optogenetics permits the manipulation of events within cells via light using the light-sensitive properties of single-component microbial opsins. Microbial opsins are activated by a light source, such as lasers, light-emitting diodes, and incandescent sources that deliver light to the region of interest either directly or indirectly, such as through fiberoptics. In classical in vivo optogenetics, the wiring of optic fibers necessitates tethering of animals by the optic fiber to the light source. The novel NeuroLux wireless optoelectronic system for optogenetics circumvents issues pertaining to classical optogenetics by utilizing near-field power transfer via magnetic coil antennae …

Methods For Film Coating Electrospun Fibers, Kristopher Dejean

Williams Honors College, Honors Research Projects

Electrospinning uses high voltages to form polymer nanofiber membranes. These membranes have potential for use in filtration, tissue engineering, drug delivery, and catalysis. The nonwoven fiber mat is malleable but has a low tensile strength compared to a solid film of the same polymer. Joining the fibers with a thin film is desired to balance the strength and flexibility. Three methods of producing a film on fiber membrane were tested. The techniques are spraying then melting, spin coating, and dip coating. Electrospinning setup conditions, solvent ratios, damage to fibers, and spin coating speeds were determined. Research was abruptly stopped and …

Chloride Effect In Fly Ash Geopolymer Cement, Evan Dimmick

Williams Honors College, Honors Research Projects

The production of ordinary portland cement (OPC) poses a significant impact on the world's carbon dioxide emissions through the wide global use of concrete. Geopolymer cements (GPC) made from alkali activated fly ash can serve as a replacement to OPCs, reducing the carbon dioxide emissions by as much as 80%. GPCs exhibit adequate or superior mechanical performance to OPCs. The corrosion of carbon steel rebar in concrete occurs largely from chloride ion attack. The focus of this project will be to experimentally determine the coefficient of diffusion for chloride ions in GPCs and OPCs and compare to the corrosion performance …

Exploring Shape-Memory Polymers From Silicone I And 1,10-Decanediol Blends, Kristina Nguyen

Williams Honors College, Honors Research Projects

Shape-memory polymers (SMPs) are polymeric materials that have dual-shape capabilities. These materials can deform to a temporary shape and will recover to their permanent original shape when induced by an external stimulus such as heat. The purpose of this project was to investigate the thermo-mechanical properties and shape-memory behavior of various blends of Silicone I and 1,10-decanediol to determine if a unique blend of these components can be utilized to develop shape memory surface relief patterns.

Careful iterative experiments were used to develop a robust procedure for the fabrication of crosslinked sheets of blends of Silicone I and 1,10-decanediol over …

Effects Of Hofmeister Ions On Solubility And Swelling On Gelatin Hydrogels, Hannah Eldridge

Williams Honors College, Honors Research Projects

Hydrogels are known to be weak and brittle, due to the amounts of water that they hold. Gelatin-based hydrogels specifically are inexpensive and easily accessible, but often have poor physical properties. The goal of my project was to strengthen gelatin-based hydrogels and improve their mechanical properties by forming these hydrogels in different aqueous solutions containing kosmotropic Hofmeister's ions. Prior research has shown that these ions are able to take water away from gelatin-based gels, which forms a tougher hydrogel. The success of this project will be measured by studying the solubility and swelling effects that different Hofmeister ions have on …

Methods For Film Coating Electrospun Fibers, Kristopher Dejean

Williams Honors College, Honors Research Projects

Electrospinning uses high voltages to form polymer nanofiber membranes. These membranes have potential for use in filtration, tissue engineering, drug delivery, and catalysis. The nonwoven fiber mat is malleable but has a low tensile strength compared to a solid film of the same polymer. Joining the fibers with a thin film is desired to balance the strength and flexibility. Three methods of producing a film on fiber membrane were tested. The techniques are spraying then melting, spin coating, and dip coating. Electrospinning setup conditions, solvent ratios, damage to fibers, and spin coating speeds were determined. Research was abruptly stopped and …

Testing The Effectiveness Of Reflective "Cool" Pigments, Ashleigh Carpenter

Williams Honors College, Honors Research Projects

This project is an exploration of reflective "cooling" pigments used in coatings for the exterior of a structure in order to control the temperature inside. The pigments reflect sunlight to reduce the heating effect inside a structure. While the project will include the synthesis and testing of these pigments, the focus will be on the design and construction of an apparatus to test the effectiveness of these pigments. An apparatus will be constructed with a heat source and two structures of identical dimensions. The set-up will allow for the temperature of the inside of the structures to be recorded at …

Electrification Of Domestic Hot Water To Aid The Integration Of Renewable Energy In The California Grid, Alejandro Cervantes

Cal Poly Humboldt theses and projects

Water heating in residential buildings, also known as domestic hot water (DHW), is the third largest use of energy after appliances and space conditioning. About 90% of the residential buildings in the state use natural gas fueled water heaters, 6% use electricity, and a small percent use liquefied petroleum gas (LPG) or solar water heaters. The current energy use associated with residential water heating is small relative to the total amount of energy consumption in the residential building sector, but it is still a contributor of greenhouse gas (GHG) emissions. Improving hot water systems can be beneficial for bill customer …

Higher Tensile Forces Across Cellular Junctions And An Intact Nuclear Linc Complex Is Required For Epithelial Function And Stability, Fnu Vani Narayanan

Theses and Dissertations

Recent advances in three-dimensional (3D) cell culture systems have provided key insights into the understanding of biochemical and physiological states of native tissue. A significant progress in the field of mechanobiology involves measuring cellular traction forces in a more native 3D environment. However, the effects of mechanical forces exerted across cellular junctions and the nuclear LINC complex, in an organized 3D system has not been investigated thus far. Epithelial cells spontaneously form acini (also known as cysts or spheroids) with a single, fluid-filled central lumen, when grown in 3D matrices. The size of the lumen is dependent on apical secretion …

Beneficiation Of Coal Using Supercritical Water And Carbon Dioxide Extraction, Matthew Decuir Virginia Commonwealth University Cl

Theses and Dissertations

This work explores the use of carbon dioxide, water, and their mixtures as solvent for the pre-combustion beneficiation of raw coal without using any toxic mineral acids in the temperature range of 200-400℃. The fluid polarity, ionic constant, and supercritical point can be adjusted by H₂O/CO₂ ratio and temperature. Adding carbon dioxide to hydrothermal fluid also increases the ionization by forming carbonic acid. Extractions with supercritical fluids have several benefits including enhanced mass transport, ease of separation and recycle, wide range of extractive capability and tunability, better inherent safety, and in the case of carbon dioxide and …

Self-Assembled Metal Nanoparticle/Polymer Nanocomposites As Nanoreactors For One-Pot Reactions, Andrew Harrison

Theses and Dissertations

Polymer nanoreactors incorporating gold nanoparticle catalysts were self-assembled via Flash Nanoprecipitation. The incorporated gold nanoparticles maintained catalytic activity, which was evaluated using reduction of 4-nitrophenol with sodium borohydride as a model reaction. The diffusion coefficient for 4-nitrophenol was determined by NMR and used to calculate the second Damköhler number, which indicated that the systems were not diffusion limited. Despite similar diffusion coefficients, catalytic performance was strongly affected by the co-precipitant. For example, the apparent reaction rate per surface area using castor oil was over 8-fold greater than polystyrene. Thus, we measured the partition coefficient of 4-nitrophenol between water and castor …