Chemical Engineering Commons^™

Comparative Analysis Of Simulation Models Of The Production Of Ethylbenzene, Osariemen Imafidon

Honors Theses

Process Engineering is all about making sure a raw material can become the desired product with as little variation as possible, while achieving the customer's specifications. Many equipment used for chemical processes cannot be physically inspected during operation at steady state, hence, the need for simulation software. The objective of this study was to compare the results of three different simulation packages to evaluate their efficacy within process design.

This study focused on the economic analysis of the production of Ethylbenzene using various models. The base case variables were inputted into each model to simulate the calculations for a fully …

The Artificial Leaf: An Investigation Into The Sociotechnical Integration Of New Solar Energy Innovations, Alexandra K. Treml, Jamie M. Mears

Senior Honors Projects, 2020-current

Increasing global demand, combined with the volatility of fossil fuels, has called for a large-scale increase in renewable energy production. Photovoltaics hold significant potential, but by nature, solar energy is intermittent and lacks dispatchability. Researchers around the world are working to create innovative solutions that utilize semiconductors found in solar cell technologies in new ways. This project harnesses photoelectrochemical water-splitting, which uses light energy to dissociate water molecules into hydrogen and oxygen. When the water-splitting device is submerged in saltwater and illuminated by sunlight, oxygen and hydrogen gas are produced on opposite surfaces, and can be either released or stored …

Ultrasound-Assisted Post-Pyrolysis Magnetization Of Microporous Biochar For Effective Removal Of Heavy Metals, Ronish Shrestha

Honors Theses

Low cost and efficient adsorption of heavy metals from wastewater and thorough removal of adsorbent after water treatment have become the two essential needs for the commercial use of any adsorbent. Biochar (BC), the solid byproduct of pyrolysis with microporous carbonaceous structure, has been increasingly recognized as an efficient adsorbent for a vast number of pollutants. Magnetization, though eases the separation and reuse of BC, significantly reduces its adsorption capacity to a comparatively much higher extent. In this study, a hybrid post-pyrolysis magnetization was developed which sustained and even significantly increased the adsorption capacity of biochar. The process included i) …

Comparative Analysis Of The Results From The Ideal Gas Assumptions With More Rigorous Calculations From Pro/Ii Of The Production Of Pharmaceutical Grade Acetone, Soibifaa Frank-Briggs

Honors Theses

The Chemical engineering team was assigned by Landshark Inc to investigate the production of 30,000 tonnes/yr of pharmaceutical-grade acetone with a purity of 99.9 wt.% from the dehydrogenation of isopropanol (IPA). The team was tasked with determining the necessary process and unit operation criteria to ensure the economic feasibility of the proposed plant.

The major goal of this thesis is to provide a data comparison of the reactor in acetone production process when designed in Microsoft Excel and Pro/II. The first part of this thesis will introduce the base case briefly, transition into engineering optimizations and show the results found …

Chemical And Thermal Sintering Of Supported Metals With Emphasis On Cobalt Catalysts During Fischer−Tropsch Synthesis, Mahmood Rahmati, Mohammad-Saeed Safdari, Thomas H. Fletcher, Morris D. Argyle, Calvin H. Bartholomew

Faculty Publications

This comprehensive critical review combines, for the first time, recent advances in nanoscale surface chemistry, surface science, DFT, adsorption calorimetry, and in situ XRD and TEM to provide new insights into catalyst sintering. This work provides qualitative and quantitative estimates of the extent and rate of sintering as functions of nanocrystal (NC) size, temperature, and atmosphere. This review is unique in that besides summarizing important, useful data from previous studies, it also advances the field through addition of (i) improved or new models, (ii) new data summarized in original tables and figures, and (iii) new fundamental perspectives into sintering of …

Bulk Properties Correlated To The Hydrogen Bond Organization In Dendrimers, Hyperbranched Polymers, And Linear Polymers, Beibei Chen

Dissertations

Although a lot of research was conducted on dendritic polymers, our understanding of their structure-property is still limited. Our previous study, which focused on a family of dendritic polymers based on 2,2-bis(hydroxymethyl) propionic acid (bis-MPA) as a monomer, discovered unique hydrogen bond organizations contributed by their dendritic structures. However, the influence of the H-bond organization on bulk properties has yet to be understood. The goal of this dissertation is to elucidate the correlation between the H-bond organization with the dielectric and volumetric properties of bis-MPA based dendritic polymers, with an emphasis on developing a fundamental understanding of to what extent …

Advancing Space Flight Medical Care Through On-Demand Protein Therapeutic Production Capabilities, Emily Long Zhao

Utah Space Grant Consortium

Cell-free protein synthesis (CFPS) is an in vitro protein synthesis system that provides a uniquely adaptable platform for protein production. In recent years, lyophilization of CFPS have expanded the capabilities of this system by improving reagent stability outside of cold-chain storage. This project sought to utilize lyophilized CFPS reagents to develop a convenient, shelf-stable, on-demand therapeutic protein production platform. The therapeutic protein production potential of this novel platform was demonstrated by the successful expression of an FDA approved therapeutic protein. With the advancement of shelf-stable, on-demand protein therapeutic production platforms comes the potential to provide point-of-care medical treatment for space-flight …

One-Dimensional Turbulence Modeling Of Soot Formation And Transport In Non-Premixed Turbulent Flames, Victoria B. Stephens

Utah Space Grant Consortium

Soot modeling in turbulent flames involves tightly coupled problems of combustion chemistry, particle transport, compressible fluid dynamics, and turbulence behavior in addition to soot chemistry and transport. Significant uncertainties accompany soot modeling and transport in such systems, hindering progress toward accurate combustion models and predictive simulation tools. The one-dimensional turbulence (ODT) model, using a stochastic approach to turbulence modeling, captures the full range of length and time scales in a simulation and provides detailed statistical data of the flow con-figuration, chemistry, and particle transport. Previously, ODT has demonstrated accuracy and computational efficiency compared to direct numerical simulation (DNS) of turbulent, …

Improving Pv Module Efficiency Through Cooling, Blake Bradley

Chemical Engineering Undergraduate Honors Theses

The Solarbacks researched and designed a variety of cooling methods that could be used to improve the efficiency of photovoltaics. These cooling methods can be separated into two categories: active and passive methods. The active cooling method of hydraulic cooling and the passive cooling methods of heat sinks (fins), optical coatings, thermosyphons, phase change materials, and thermoelectric generators were all taken into consideration as potential cooling methods. Passive cooling methods were preferred because the use of electricity required for the cooling mechanism would reduce the net electricity and subsequent profit from the panels.

Two variations of hydraulic cooling were researched: …

Improving Pv Module Efficiency Through Cooling, Megan Reynolds

Chemical Engineering Undergraduate Honors Theses

The Solarbacks researched and designed a variety of cooling methods that could be used to improve the efficiency of photovoltaics. These cooling methods can be separated into two categories: active and passive methods. The active cooling method of hydraulic cooling and the passive cooling methods of heat sinks (fins), optical coatings, thermosyphons, phase change materials, and thermoelectric generators were all taken into consideration as potential cooling methods. Passive cooling methods were preferred because the use of electricity required for the cooling mechanism would reduce the net electricity and subsequent profit from the panels.

Two variations of hydraulic cooling were researched: …

Solution To Exide Technologies Inbatec Inefficiency, Shixuan Hou, Reagan Gilker, Mary Fairley, Spencer Christian, Covenson Latouche

Chemical Engineering Undergraduate Honors Theses

The inefficiency of the battery charging time in Inbatec Units 1 and 2 in the Exide Technologies Fort Smith was initially investigated by a student team in Fall 2019, and the investigation was continued into Spring 2020. The Exide Technologies facility in Fort Smith, Arkansas utilizes 13 Inbatec units to charge the lead-acid batteries. The Inbatec systems circulate the sulfuric acid solution through a cooling tower to maintain to optimal charging temperature. Previous analysis of the charging process for Inbatec Units 1 and 2 show the cooling tower have the capacity to quickly remove the excess heat in the sulfuric …

Investigating The Effect Of Hydrophilic Block Length On The Co-Assembly Behavior Of Amphiphilic Triblock Copolymers, Alexandra M. Garrett

Honors Theses

Polymer vesicles and micelles have been of interest in the scientific community for the past few decades due to potential biomedical applications in areas such as drug delivery, nanoreactors, and biosensing. Polymer vesicles and micelles are formed through the self-assembly of amphiphilic block copolymers. The objective of this project is to gain a better understanding of the influence of hydrophilic block copolymer length and composition in controlling the resulting morphologies from the co-assembly of triblock copolymers. First, a hydrophobic block composed of poly(methyl acrylate) was synthesized using reversible addition-fragmentation chain-transfer (RAFT) polymerization mediated by a difunctional chain-transfer agent. The block …

Synthesizing And Modeling The Optical Properties Of Silica Aerogel, Hannah Margavio

Honors Theses

Silica aerogel has attracted the attention of researchers for decades for its applications in insulation materials, storage, and solar-thermal devices. The appeal surrounding silica aerogel is attributed to its unique combination of physical and chemical properties. Silica aerogel is a highly porous, optically transparent nano-polymer with a low thermal conductivity. Additionally, the material boasts a super-low density, high specific surface area, and low dielectric constant. The following report proposes a viable method of synthesizing polyvinylpolymethylsilane (PVPMS) aerogel as well as a model for determining the optical performance of TMOS aerogel by determining its radiative properties. First, the report will explore …

Pollution Prevention Via Recovery Of Cerium (Iv) Oxide In Optics Company, Eugene Park, William Gallagher, Sydor Optics, Flint Creek Resources

Articles

Pollution prevention methods were applied at an optics manufacturer in an effort to improve recovery of a valuable polishing component, cerium oxide (ceria), 77% of which was lost to dragout and sewer discharge. Centrifugation and microfiltratiion were evaluated to develop a process that would increase recovery of used ceria, which would then be sent back to the ceria supplier for reclamation and reuse. Full-scale implementation included a high-speed centrifuge that operates continuously with a microfiltration system through recirculation in a single process tank. Sydor Optics has improved ceria recovery from 23% to 48%, saving thousands of dollars annually.

Solution To Exide Technologies Inbatec Inefficiency, Mary Fairley, Reagan Gilker, Spencer Christian, Shixuan Hou, Covenson Latouche

Chemical Engineering Undergraduate Honors Theses

The inefficiency of the battery charging time in Inbatec Units 1 and 2 in the Exide Technologies Fort Smith was initially investigated by a student team in Fall 2019, and the investigation was continued into Spring 2020. The Exide Technologies facility in Fort Smith, Arkansas utilizes 13 Inbatec units to charge the lead-acid batteries.

The Inbatec systems circulate the sulfuric acid solution through a cooling tower to maintain to optimal charging temperature. Previous analysis of the charging process for Inbatec Units 1 and 2 show the cooling tower have the capacity to quickly remove the excess heat in the sulfuric …

Improving Pv Module Efficiency Through Cooling, Harrison Dawson

Chemical Engineering Undergraduate Honors Theses

The Solarbacks researched and designed a variety of cooling methods that could be used to improve the efficiency of photovoltaics. These cooling methods can be separated into two categories: active and passive methods. The active cooling method of hydraulic cooling and the passive cooling methods of heat sinks (fins), optical coatings, thermosyphons, phase change materials, and thermoelectric generators were all taken into consideration as potential cooling methods. Passive cooling methods were preferred because the use of electricity required for the cooling mechanism would reduce the net electricity and subsequent profit from the panels.

Two variations of hydraulic cooling were researched: …

Characterization Of Oxone Mediated Tempo-Oxidized Nano Cellulose Mixed-Matrix Membranes During Ultrafiltration And Hemodialysis, Kristyn Robling

Biomedical Engineering Undergraduate Honors Theses

The ninth leading cause of death in the United States is kidney disease, and hemodialysis is the process most commonly prescribed for treatment. It utilizes a selectively permeable membrane filter to remove toxins such as urea from the blood and retain necessary protein levels. However, traditional filters, such as cellulose triacetate, used during dialysis can be inefficient in terms of separation performance and reduction of fouling. Recent exploration of nanoparticles has resulted in the creation of Oxone Mediated TEMPO-Oxidized Nano Cellulose which has properties that are believed to increase hydrophilicity, increase tensile capacity, decrease membrane resistance and lower fouling, making …

Numerical And Experimental Analysis Of Air-Cooled Condensers, Kaipo Kekaula

UNLV Theses, Dissertations, Professional Papers, and Capstones

The scope of this project is to numerically and experimentally dry cooling process in air-cooled condensers (ACCs) designed for concentrated solar power (CSP) applications. This effort is driven by the growing economic and political pressure to reduce water consumption during power generation due to limited water resources in the arid geographic climate of the southwestern United States. A computational approach is used in conjunction with experimental validation to gain a more complete understanding of these systems.

Traditionally research into ACCs have been largely limited to air-side heat transfer modelling as it accounts for a large portion of the total thermal …

Removal Of Fluoride From Mine Water Via Adsorption For Land-Applied Soil Amendment, Kevin Le, Adrian Damian, Mary Johnson, Ethan Phan, Courtney Golman, Michelle Dopp, Jacqueline Payne

Chemical Engineering Undergraduate Honors Theses

The team researched, designed, and economically analyzed a full-scale adsorption column system to be applied in mining processes that leave high amounts of fluoride in their effluent. This system was designed to remove fluoride from water saturated with calcium sulfate, as calcium sulfate is present in high amounts in certain mining processes. Currently, high density sludge (HDS) is commonly employed to reduce fluoride concentrations, but due to solubility limits the sludge treatment cannot lower fluoride below 10 mg/L (ppm). The current enforceable EPA standard for discharged water is at 4 mg/L (ppm), although mining companies anticipate that this standard will …

Removal Of Fluoride From Mine Water Via Adsorption For Land-Applied Soil Amendment, Michelle Dopp, Kevin Le, Ethan Phan, Mary Johnson, Jacqueline Payne, Adrian Damian, Courtney Golman

Chemical Engineering Undergraduate Honors Theses

The Moo Pig Sooie’s researched, designed, and economically analyzed a full-scale adsorption column system to be applied in mining processes that leave high amounts of fluoride in their effluent. This system was designed to remove fluoride from water saturated with calcium sulfate, as calcium sulfate is present in high amounts in certain mining processes. Currently, high density sludge (HDS) is commonly employed to reduce fluoride concentrations, but due to solubility limits the sludge treatment cannot lower fluoride below 10 mg/L (ppm). The current enforceable EPA standard for discharged water is at 4 mg/L (ppm), although mining companies anticipate that this …

Analysis Of Blood Purification Studies On Oxone Mediated Tempo-Oxidized Nano Cellulose Mixed-Matrix Membranes, Tony Roller

Biomedical Engineering Undergraduate Honors Theses

End-stage renal disease (ESRD) is currently the ninth leading cause of death in the United States, and of the 661,00 Americans diagnosed with ESRD, approximately 468,800 were on hemodialysis in 2016. Hemodialysis refers to a technique where a machine combined with a membrane, often referred to as an artificial kidney, is used to clean blood by removing any waste such as urea, potassium, and other smaller waste products while preserving the concentrations and integrity of cells and proteins in the blood. It has been shown in artificial blood studies that cellulose nanomaterials, like TEMPO/Oxidized cellulose nanoparticles (TOCNs), can be integrated …

Electrodialysis Device For In Vivo Power Delivery, Jessica L. Orton

Biomedical Engineering Undergraduate Honors Theses

It is estimated that over 3 million cardiac pacemakers have been implanted in patients globally. Current lithium-iodine pacemaker batteries last an average of about 10 years before the entire pacemaker unit must surgically be replaced, increasing the patient’s risk of procedure-related complications. Therefore, it is necessary to investigate means by which to extend the pacemaker battery lifetime. The renal vein and renal artery in the body naturally produce a salinity gradient through the filtering work of the kidneys. This salinity gradient energy potential can be harnessed through reverse electrodialysis (RED). RED is an electrochemical process that harnesses the Gibbs Free …

Quantifying Air Pollution At The Stamford Transportation Center, Brianna Mancuso, Kristina Wagstrom

Honors Scholar Theses

There is a need to analyze particulate matter concentrations at the Stamford Transportation Center according to the Western Connecticut Coalition of Governments. Stamford has recently undergone rapid urbanization and large scale construction resulting in traffic congestion. Congested traffic areas in urban centers are key contributors to poor air quality. Therefore, there is a need to analyze the pollution concentrations at the bus stops near the station. Every day, hundreds of shuttles and cars idle around the Transportation Center. Thousands of passengers wait at nearby bus stops every day and can potentially be exposed to high amounts of vehicle produced pollution …

Solution To Exide Technologies Inbatec Inefficiency, Spencer Christian, Shixuan Hou, Mary Fairley, Reagan Gilker, Covenson Latouche

Chemical Engineering Undergraduate Honors Theses

The inefficiency of the battery charging time in Inbatec Units 1 and 2 in the Exide Technologies Fort Smith was initially investigated by a student team in Fall 2019, and the investigation was continued into Spring 2020. The Exide Technologies facility in Fort Smith, Arkansas utilizes 13 Inbatec units to charge the lead-acid batteries. The Inbatec systems circulate the sulfuric acid solution through a cooling tower to maintain to optimal charging temperature. Previous analysis of the charging process for Inbatec Units 1 and 2 show the cooling tower have the capacity to quickly remove the excess heat in the sulfuric …

Removal Of Fluoride From Mine Water Via Adsorption For Land-Applied Soil Amendment, Jacqueline Payne, Mary Johnson, Kevin Le, Michelle Dopp, Courtney Golman, Adrian Damian, Ethan Phan

Chemical Engineering Undergraduate Honors Theses

The process of mining minerals and elements from ores and rocks creates acid rock drainage (ARD). This drainage is water that contains heavy metals and minerals that can be dangerous for human consumption or damaging to the environment. The mining industry has employed various water treatment methods to prevent these metals and minerals from being discharged into water sources such as ponds, lakes, and streams. Currently, the most used treatment process in the mining industry is a cost-effective highdensity sludge (HDS) process. This method reduces the concentration of metals and elements with the use of lime/limestone. However, the concentration of …

Removal Of Fluoride From Mine Water Via Adsorption For Land-Applied Soil Amendment, Ethan Phan, Adrian Damian, Kevin Le, Mary Johnson, Courtney Golman, Michelle Dopp, Jacqueline Payne

Chemical Engineering Undergraduate Honors Theses

The process of mining minerals and elements from ores and rocks creates acid rock drainage (ARD). This drainage is water that contains heavy metals and minerals that can be dangerous for human consumption or damaging to the environment. The mining industry has employed various water treatment methods to prevent these metals and minerals from being discharged into water sources such as ponds, lakes, and streams. Currently, the most used treatment process in the mining industry is a cost-effective high-density sludge (HDS) process. This method reduces the concentration of metals and elements with the use of lime/limestone. However, the concentration of …

Scale-Up Of Polyaniline Cellulose Membranes, Isaac Bodemann

Chemical Engineering Undergraduate Honors Theses

Polyaniline coated cellulose membranes show impressive conductive properties that may be used to innovate traditional charged separation techniques, such as electrodeionization. However, these membranes are not sold to consumers, so they cannot be easily integrated into such systems. This research focuses on the scale-up and development of positively charged anion exchange membranes to be used in EDI cells. Novel cellulose membranes were made using lab-specific cellulose. These membranes were then coated using a polyaniline technique adopted from a paper titled, “Flexible Electrically Conductive Nanocomposite Membrane Based on Bacterial Cellulose and Polyaniline." This paper details the methods used to add the …

Solution To Exide Technologies Inbatec Inefficiency, Reagan Gilker, Mary Fairley, Spencer Christain, Shixuan Hou, Covenson Latouche

Chemical Engineering Undergraduate Honors Theses

The inefficiency of the battery charging time in Inbatec Units 1 and 2 in the Exide Technologies Fort Smith was initially investigated by a student team in Fall 2019, and the investigation was continued into Spring 2020. The Exide Technologies facility in Fort Smith, Arkansas utilizes 13 Inbatec units to charge the lead-acid batteries.

The Inbatec systems circulate the sulfuric acid solution through a cooling tower to maintain to optimal charging temperature. Previous analysis of the charging process for Inbatec Units 1 and 2 show the cooling tower have the capacity to quickly remove the excess heat in the sulfuric …

Improving Pv Module Efficiency Through Cooling, Ashley Cox

Chemical Engineering Undergraduate Honors Theses

The Solarbacks researched and designed a variety of cooling methods that could be used to improve the efficiency of photovoltaics. These cooling methods can be separated into two categories: active and passive methods. The active cooling method of hydraulic cooling and the passive cooling methods of heat sinks (fins), optical coatings, thermosyphons, phase change materials, and thermoelectric generators were all taken into consideration as potential cooling methods. Passive cooling methods were preferred because the use of electricity required for the cooling mechanism would reduce the net electricity and subsequent profit from the panels.

Two variations of hydraulic cooling were researched: …

Removal Of Fluoride From Mine Water Via Adsorption For Land-Applied Soil Amendment, Adrian Damian, Kevin Le, Mary Johnson, Ethan Phan, Courtney Golman, Michelle Dopp, Jacqueline Payne

Chemical Engineering Undergraduate Honors Theses

The process of mining minerals and elements from ores and rocks creates acid rock drainage (ARD). This drainage is water that contains heavy metals and minerals that can be dangerous for human consumption or damaging to the environment. The mining industry has employed various water treatment methods to prevent these metals and minerals from being discharged into water sources such as ponds, lakes, and streams. Currently, the most used treatment process in the mining industry is a cost-effective highdensity sludge (HDS) process. This method reduces the concentration of metals and elements with the use of lime/limestone. However, the concentration of …